BH6172GU_11 [ROHM]
System Regulator with High Efficiency DC/DC Converters; 系统调节器,高效率DC / DC转换器型号: | BH6172GU_11 |
厂家: | ROHM |
描述: | System Regulator with High Efficiency DC/DC Converters |
文件: | 总17页 (文件大小:382K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Power Management ICs for Mobile Phones
System Regulator
with High Efficiency DC/DC Converters
No.11032EAT04
BH6172GU
●Descriptions
BH6172GU incorporates 1 DCDC+ 5 Linear LDO regulators. It is integrated in a small 2.6mm×2.6mm size package, with 16
steps adjustable Vo’s for every channel, low voltage output (0.8V~) to support almost any kind of mobile application now
available.
●Features
1) 1ch 500mA, high efficiency Step-down Converter. (16 steps adjustable VO by I2C)
2) 5-channel CMOS-type LDOs. (16 steps adjustable VO by I2C, 150mA×3, 300mA×2)
3) Power ON/OFF control enabled by I2C interface or external pin
4) I2C compatible Interface. (Device address is “1001111”)
5) Wafer Level CSP package(2.6mm×2.6mm) for space-constrained applications
6) Discharge resistance selectable for power-down sequence ramp speed control
7) Over-current protection in all LDO regulators
8) Over-current protection in Step-down Converter
9) Over-voltage protection in Step-down Converter
10) Thermal shutdown protection
●Applications
Mobile phones, Portable game systems, Portable mp3 players, Portable DVD players, Portable TV, Portable GPS,
PDA, Portable electronic dictionaries, etc.
●Absolute maximum ratings (Ta=25℃)
Parameter
Symbol
Ratings
Unit
Maximum Supply Voltage (VBAT)
Maximum Supply Voltage (PBAT)
Maximum Supply Voltage (VUSB)
Maximum Supply Voltage (DVDD)
VBATMAX
VPBATMAX
VUSBMAX
DVDDMAX
6.0
6.0
6.0
4.5
V
V
V
V
Maximum Input Voltage 1
(LX, FB, OUT1, OUT2, OUT3, OUT4, OUT5,
EN_LD1, EN_LD2, EN_LD3, EN_LD4)
VINMAX1
VBAT + 0.3
V
Maximum Input Voltage 2
(NRST, CLK, DATA)
VINMAX2
Pd
DVDD + 0.3
900*1
V
mW
℃
Power Dissipation
Operating Temperature Range
Storage Temperature Range
Topr
-35 ~ +85
-55 ~ +125
Tstg
℃
*
This is an allowable loss of the ROHM evaluation glass epoxy board(60mm×60mm×16mm).
To use at temperature higher than 25℃ , derate 9.0mW per 1℃.
*1 Must not exceed Pd or ASO.
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
2011.03 - Rev.A
1/16
Technical Note
BH6172GU
●Recommended Operating Conditions (Ta=25℃)
Parameter
VBAT Voltage
Symbol
Ratings
Unit
VBAT
VPBAT
VUSB
2.20 ~ 5.50*2
2.20 ~ 5.50*2
2.20 ~ 5.50*2*3
1.70 ~ 4.20*4
V
V
V
V
PBAT Voltage
VUSB Voltage
DVDD Voltage
VDVDD
*2 Whenever the VBAT or PBAT or VUSB voltage is under the LDO, SWREG output voltage,
or else under certain levels, the LDO and SWREG output is not guaranteed to meet its published specifications.
*3 VUSB Power Supply can be externally connected to the VBAT, PBAT Power Supply when necessary.
*4 The DVDD Voltage must be under the Battery Voltage VBAT, PBAT at any times.
●Electrical Characteristics (Unless otherwise specified, Ta=25℃, VBAT=PBAT =3.6V, VUSB=5.0V)
Limits
Parameter
Circuit Current
Symbol
Unit
Condition
Min.
Typ.
Max.
VBAT Circuit Current 1
(OFF)
LDO1~5=OFF
SWREG1=OFF
NRST=L
IQVB1
-
-
0.4
0
1
1
µA
µA
VUSB Circuit Current 1
(OFF)
IQUSB1
DVDD=0V
LDO1~5=OFF
SWREG1=OFF
NRST=L
VBAT Circuit Current 2
(OFF)
IQVB2
-
0.4
1
µA
DVDD=0V
VUSB=VBAT external connection
VBAT Circuit Current 3
(STANDBY)
LDO1~5=OFF
SWREG1=OFF
NRST=H
IQVB3
-
-
0.7
0
1.4
1
µA
µA
VUSB Circuit Current 2
(STANDBY)
IQUSB2
DVDD=2.6V
LDO1~5=OFF
SWREG1=OFF
NRST=H
DVDD=2.6V
VBAT Circuit Current 4
(STANDBY)
IQVB4
-
0.7
1.4
µA
VUSB=VBAT external connection
VBAT Circuit Current 5
(Active)
LDO1~5=ON(no load, initial voltage)
SWREG1=ON(no load, initial voltage)
NRST=H
IQVB5
-
-
170
35
300
70
µA
µA
VUSB Circuit Current 3
(Active)
IQUSB3
DVDD=2.6V
LDO1~5=ON(no load, initial voltage)
SWREG1=ON(no load, initial voltage)
NRST=H
VBAT Circuit Current 6
(Active)
IQVB6
-
200
350
µA
DVDD=2.6V
VUSB=VBAT external connection
◎This product is not especially designed to be protected from radioactivity.
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
2011.03 - Rev.A
2/16
Technical Note
BH6172GU
●Electrical Characteristics (Unless otherwise specified, Ta=25℃, VBAT=PBAT =3.6V, VUSB=5.0V, DVDD=2.6V)
Limits
Parameter
Symbol
Unit
Condition
Min.
Typ.
Max.
Logic pin character
Input
“H” level
DVDD
×0.7
DVDD
+0.3
VIH1
VIL1
IIC1
-
-
V
V
Pin voltage: DVDD
NRST
(CMOS input)
Input
“L” level
DVDD
×0.3
-0.3
0
Pin voltage: 0 V
Input leak
current
0.3
-
1
-
µA
V
Input
“H” level
VIH2
VIL2
IIC2
1.44
-
EN_LD1,
EN_LD2,
EN_LD3,
EN_LD4
Input
“L” level
-
0.4
1
V
Input leak
current
(NMOS input)
-1
0
µA
Digital characteristics (Digital pins: CLK and DATA )
DVDD
DVDD
+0.3
Input "H" level
Input "L" level
Input leak current
VIH3
VIL3
IIC3
-
-
V
V
×0.8
-0.3
DVDD
×0.2
-1
-
0
-
1
µA
V
Pin voltage: DVDD
IOL=6mA
DATA output "L" level voltage
SWREG
VOL
0.4
initial value
Io=100mA
Output Voltage
VOSW
IOSW
0.94
1.00
-
1.06
V
mA
%
Output current
-
-
500
Vo=1.00V
Efficiency
ηSW
90
-
-
-
-
-
Io=100mA, Vo=2.40V, VBAT=3.2V
Oscillating Frequency
Output Inductance
Short circuit current
Output Capacitance
fOSC
-
1.7
2.2
500
4.7
MHz Vo=1.00V
LSWREG
ISHTSW
CSWREG
1.5
-
µH
mA
µF
Ta= -30~75℃
Ta= -30~75℃
Ta= -30~75℃
with SWREG's DC bias
3.3
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
2011.03 - Rev.A
3/16
Technical Note
BH6172GU
●Electrical Characteristics (Unless otherwise specified, Ta=25℃, VBAT=PBAT =3.6V, VUSB=5.0V)
Limits
Parameter
Symbol
Unit
Condition
Min.
Typ.
Max.
LDO1
initial value
Io=1mA@VBAT=4.5V
Output Voltage
VOM1
0.970
1.000
1.030
V
Io=150mA@VBAT=3.4V
Output current
VOM1C
VOM1DP
⊿VIM1
-
-
-
-
-
150
mA
V
Vo=1.0V
Io=50mA
Dropout Voltage
Input Voltage Stability
Load Stability
0.1
2
-
-
-
VBAT=3.4~4.5V, Io=50mA
Vo=1.0V
mV
mV
Io=50µA~150mA, VBAT=3.6V
Vo=1.0V
⊿VLM1
20
VR=-20dBV, fR=120Hz
Io=50mA, Vo=2.6V
BW=20Hz~20kHz
Ripple rejection ratio
Short circuit current
RRM1
-
60
-
dB
ISHTM3
COUT1
-
-
180
1.0
-
-
mA
µF
Vo=0V
Ta= -30~75℃
with LDO's DC bias
Output Capacitor
LDO2
initial value
Io=1mA@VBAT=4.5V
Output Voltage
VOM2
2.522
2.600
2.678
V
Io=150mA@VBAT=3.4V
Output current
VOM2C
VOM2DP
⊿VIM2
-
-
-
-
-
150
mA
V
Vo=2.6V
Io=50mA
Dropout Voltage
Input Voltage Stability
Load Stability
0.1
2
-
-
-
VBAT=3.4~4.5V, Io=50mA
Vo=2.6V
mV
mV
Io=50µA~150mA, VBAT=3.6V
Vo=2.6V
⊿VLM2
20
VR=-20dBV, fR=120Hz
Io=50mA, Vo=2.6V
BW=20Hz~20kHz
Ripple rejection ratio
Short circuit current
RRM2
-
60
-
dB
ISHTM3
COUT2
-
-
180
1.0
-
-
mA
µF
Vo=0V
Ta= -30~75℃
with LDO's DC bias
Output Capacitor
LDO3
initial value
Io=1mA@VBAT=4.5V
Io=150mA@VBAT=3.4V
Output Voltage
VOM3
2.716
2.800
2.884
V
Output current
VOM3C
VOM3DP
⊿VIM3
-
-
-
-
-
300
mA
V
Vo=2.8V
Io=50mA
Dropout Voltage
Input Voltage Stability
Load Stability
0.1
2
-
-
-
VBAT=3.4~4.5V, Io=50mA
Vo=2.8V
mV
mV
Io=50µA~300mA, VBAT=3.6V
Vo=2.8V
⊿VLM3
20
VR=-20dBV, fR=120Hz
Io=50mA, Vo=2.6V
BW=20Hz~20kHz
Ripple rejection ratio
RRM3
-
60
-
dB
Short circuit current
Output Capacitor
ISHTM3
COUT3
-
-
180
1.0
-
-
mA
µF
Vo=0V
Ta= -30~75℃
with LDO's DC bias
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
2011.03 - Rev.A
4/16
Technical Note
BH6172GU
●Electrical Characteristics (Unless otherwise specified, Ta=25℃, VBAT=PBAT =3.6V, VUSB=5.0V)
Limits
Parameter
Symbol
Unit
Condition
Min.
Typ.
Max.
LDO4
initial value
Io=1mA@VBAT=4.5V
Output Voltage
VOM4
1.746
1.800
1.854
V
Io=300mA@VBAT=3.4V
Output current
VOM4C
VOM4DP
⊿VIM4
-
-
-
-
-
300
mA
V
Vo=1.8V
Io=50mA
Dropout Voltage
Input Voltage Stability
Load Stability
0.1
2
-
-
-
VBAT=3.4~4.5V, Io=50mA
Vo=1.8V
mV
mV
Io=50µA~300mA, VBAT=3.6V
Vo=1.8V
⊿VLM4
30
VR=-20dBV, fR=120Hz
Io=50mA, Vo=2.6V
BW=20Hz~20kHz
Ripple rejection ratio
Short circuit current
RRM4
-
60
-
dB
ISHTM4
COUT4
-
-
340
1.0
-
-
mA
µF
Vo=0V
Ta= -30~75℃
with LDO's DC bias
Output Capacitor
LDO5
initial value
Io=1mA@VUSB=5.5V
Output Voltage
VOM5
3.201
3.300
3.399
V
Io=150mA@VUSB=4.4V
Output current
VOM5C
VOM5DP
⊿VIM5
-
-
-
-
-
150
mA
V
Vo=3.3V
Io=50mA
Dropout Voltage
Input Voltage Stability
Load Stability
0.1
2
-
-
-
VUSB=4.4~5.5V, Io=50mA
Vo=3.3V
mV
mV
Io=50µA~150mA, VUSB=5.5V
Vo=3.3V
⊿VLM5
20
VR=-20dBV, fR=120Hz
Io=50mA, Vo=2.6V
BW=20Hz~20kHz
Ripple rejection ratio
RRM5
-
60
-
dB
Short circuit current
Output Capacitor
ISHTM5
COUT5
-
-
180
1.0
-
-
mA
µF
Vo=0V
Ta= -30~75℃
with LDO's DC bias
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
2011.03 - Rev.A
5/16
Technical Note
BH6172GU
●SWREG & LDOs Output Voltage table
Initial
Output Voltage
Parameter
SWREG
Usage example
Power Supply
Load max
Adjustable range
CORE
CORE
I/O1
VBAT/PBAT
VBAT
1.00V
1.00V
2.60V
2.80V
1.80V
3.30V
500mA
150mA
150mA
300mA
300mA
150mA
0.80-2.40V
1.00-3.30V
1.00-3.30V
1.20-3.30V
1.20-3.30V
1.20-3.30V
LDO1
LDO2
LDO3
LDO4
LDO5
VBAT
MEMORY
I/O2
VBAT
VBAT
USB
VBAT/VUSB
Parameter
SWREG
LDO1
LDO2
LDO3
LDO4
LDO5
0.80V
0.85V
0.90V
0.95V
1.00V
1.05V
1.10V
1.15V
1.20V
1.365V
1.40V
1.50V
1.65V
1.80V
1.85V
2.40V
1.00V
1.10V
1.20V
1.30V
1.40V
1.50V
1.60V
1.70V
1.80V
1.85V
2.60V
2.70V
2.80V
2.85V
3.00V
3.30V
1.00V
1.10V
1.20V
1.30V
1.40V
1.50V
1.60V
1.70V
1.80V
1.85V
2.60V
2.70V
2.80V
2.85V
3.00V
3.30V
1.20V
1.30V
1.40V
1.50V
1.60V
1.70V
1.80V
1.85V
1.90V
2.00V
2.60V
2.70V
2.80V
2.85V
3.00V
3.30V
1.20V
1.30V
1.40V
1.50V
1.60V
1.70V
1.80V
1.85V
1.90V
2.00V
2.60V
2.70V
2.80V
2.85V
3.00V
3.30V
1.20V
1.30V
1.40V
1.50V
1.60V
1.70V
1.80V
1.85V
1.90V
2.00V
2.60V
2.70V
2.80V
2.85V
3.00V
3.30V
Programmable
Output Voltages
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
2011.03 - Rev.A
6/16
Technical Note
BH6172GU
●Block diagram, Ball matrix
4.7µF
OUT1
init 1.00V
150mA
LDO1
DVDD
DATA
1.00-3.30V
0.1V step
1µF
1µF
1µF
1µF
VBAT1
OUT2
GND
TEST2
EN_LD2
EN_LD1
OUT4
EN_LD3
EN_LD4
TEST
VBAT2
NRST
CLK
OUT3
OUT1
DVDD
FB
EN_LD1
E
D
C
B
A
I2CIF
CLK
OUT2
init 2.60V
150mA
LDO2
1.00-3.30V
0.1V step
NRST
EN_LD2
PBAT
OUT3
init 2.80V
300mA
LDO3
1.20-3.30V
0.1V step
4.7µF
2.2µH
LX
SWREG
0.8-2.40V
4.7µF
EN_LD3
PGND
500mA
OUT4
init 1.00V
init 1.80V
300mA
LDO4
1.20-3.30V
0.1V step
FB
REFC
DATA
EN_LD4
(OPEN) TEST
(OPEN) TEST2
VUSB
1µF
1µF
OUT5
VUSB
PGND
LX
PBAT
REFC
init 3.30V
150mA
OUT5
REF
LDO5
1.20-3.30V
0.1V step
0.1µF
1
2
3
4
5
Fig.1 Block diagram
Fig.2 Ball matrix
●Pin description
Ball No.
PIN Name
Function
B4
C4
E1
E4
A5
A4
A3
B5
D4
D5
D1
E5
E3
A1
B1
C2
D2
D3
C3
A2
C5
C1
B3
E2
DATA
CLK
Data input/output for I2C
CLK input for I2C
VBAT1
VBAT2
PBAT
LX
Power Supply 1
Power Supply 2
Power Supply for SWREG
Inductor Connect pin for SWREG
Ground for SWREG
Voltage Feed back pin for SWREG
RESET Input Pin (Low Active)
LDO1 Output
PGND
FB
NRST
OUT1
OUT2
OUT3
OUT4
OUT5
REFC
EN_LD1
EN_LD2
EN_LD3
EN_LD4
VUSB
DVDD
GND
LDO2 Output
LDO3 Output
LDO4 Output
LDO5 Output
Reference Voltage Output
LDO1 Enable Pin
LDO2 Enable Pin
LDO3 Enable Pin
LDO4 Enable Pin
USBVBUS Power Supply*1
Digital Power Supply
Analog Ground
TEST
TEST2
TEST PIN (Always keep OPEN at normal use)
TEST PIN (Always keep OPEN at normal use)
*
EST, TEST2 pin is used during our company shipment test.
lease keep TEST pin and TEST2 pin “OPEN” at all times.
*1 USB Power Supply can be externally connected to the VBAT Power Supply when necessary.
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
2011.03 - Rev.A
7/16
Technical Note
BH6172GU
●I2C Bus Interface
The I2C compatible synchronous serial interface provides access to programmable functions and register on the device.
This protocol uses a two-wire interface for bi-directional communications between the LSI’s connected to the bus.
The two interface lines are the Serial Data Line (DATA), and the Serial Clock Line (CLK). These lines should be connected to
the power supply DVDD by a pull-up resistor, and remain high even when the bus is idle.
1. Start and Stop Conditions
When CLK is high, pulling DATA low produces a start condition and pulling DATA high produces a stop condition.
Every instruction is started when a start condition occurs and terminated when a stop condition occurs. During read, a stop
condition causes the read to terminate and the chip enters the standby state. During write, a stop condition causes the
fetching of write data to terminate, after which writing starts automatically. Upon the completion of writing, the chip enters
the standby state. Two or more start conditions cannot be entered consecutively.
tSU.STA
tHD.STA
tSU.STO
CLK
DATA
Start condition
Stop condition
Fig.3 I2C Start, Stop condition
2. Data transmission
Data on the DATA input can be modified while CLK is low. When CLK is high, modifying the DATA input means a start or
stop condition.
tSU.DAT
tHD.DAT
CLK
DATA
Modify data
Modify data
Fig.4 I2C Data Transmission Timing
All other acknowledge, write, and read timings all conform to the I2C standard.
3. Device addressing
The device address for this device is “1001111”.
Read/write instruction
Device address
code
R/W
1
0
0
1
1
1
1
MSB
LSB
Fig.5 I2C device address
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
2011.03 - Rev.A
8/16
Technical Note
BH6172GU
●I2C Bus AC specification
Characteristics
Symbol
Min.
Max.
Unit
CLK clock frequency
CLK clock “low” time
CLK clock “high” time
Bus free time
fCLK
tLOW
0
400
kHz
µs
µs
µs
µs
µs
ns
ns
µs
1.3
0.6
1.3
0.6
0.6
0
-
-
-
-
-
-
-
-
tHIGH
tBUF
Start condition hold time
Start condition setup time
Data input hold time
Data input setup time
Stop condition setup time
tHD.STA
tSU.STA
tHD.DAT
tSU.DAT
tSU.STO
100
0.6
tF
tR
tLOW
tHIGH
CLK
tSU.STO
tHD.DAT tSU.DAT
tSU.STA tHD.STA
DATA
(INPUT)
tBUF
Fig.6 Bus timing 1
CLK
DATA
DO
(INPUT)
tWR
Start condition
Acknowledge output
Write data input
Stop condition
Fig.7 Bus timing 2
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
2011.03 - Rev.A
9/16
Technical Note
BH6172GU
●I2C Register information
○REGCNT(SWREGON, LDO*ON)
Control each SWREG, LDO.
0
1
ON
OFF
○SWADJ(SWREGADJ[3:0])
Change SWREG output voltage by 16 steps.
“0000”
0.80V
“1111”
2.40V
○LDOADJ*(LDO*ADJ[3:0])
Change LDO1~5 output voltage by 16 steps.
“0000”
1.00V(LDO1, 2), 1.20V(LDO3, 4, 5)
“1111”
3.30V
○PDSEL(SWPDSEL, LDO*PDSEL)
Change the discharge resistance of SWREG, LDO.
0
1
1kΩ
10kΩ
○PDCNT(SWPD, LDO*PD)
Enable/disable the discharge resistance of SWREG, LDO.
0
1
Discharge disable
Discharge enable
○EN_SEL(ENLD*_EN)
Select either an enable pin or I2C register for LDO1~4 ON/OFF control.
0
1
External enable pin selected
I2C register selected
www.rohm.com
2011.03 - Rev.A
10/16
© 2011 ROHM Co., Ltd. All rights reserved.
Technical Note
BH6172GU
●Reference data(ICC)
ICC(OFF) VUSB=5.0V
ICC(OFF) VBAT=VUSB short
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
VBAT [V]
VBAT [V]
ICC(ACTIVE) VBAT=VUSB short
ICC(STBY) VBAT=VUSB short
1
10
9
8
7
6
5
4
3
2
1
0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
3.2
3.7
4.2
4.7
5.2
5.7
VBAT [V]
VBAT [V]
●Reference data(SWREG)
SWREG Load Regulation VO=1.0V
SWREG Line Regulation VO=1.0V
2
1.9
1.8
1.7
1.6
1.5
1.4
1.3
1.2
1.1
1
6
5.5
5
VBAT
4.5
4
3.5
3
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
2.5
2
1.5
1
0.5
0
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
0
50
100
150
200
250
IO [mA]
300
350
400
450
500
VBAT [V]
SWREG Efficiency vs Io (Vo=1.365V)
VBAT=3.6V
100
90
80
70
60
50
40
30
20
10
0
0
50
100
150
200
250
300
350
400
450
500
IO[mA]
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
2011.03 - Rev.A
11/16
Technical Note
BH6172GU
●Reference data(Output stability)
4
3.5
3
4
4
3.5
3
LDO3 Load Regulation 3.0V
LDO2 Load Regulation 2.60V
LDO1 Load Regulation 1.20V
3.5
3
2.5
2
2.5
2
2.5
2
1.5
1
1.5
1
1.5
1
0.5
0
0.5
0
0.5
0
0
50
100
150
200
0
50
100
150
200
250
300
0
50
100
150
200
IO [mA]
IO [mA]
IO [mA]
4
3.5
3
4
LDO4 Load Regulation 1.80V
LDO5 Load Regulation 3.30V
3.5
3
2.5
2
2.5
2
1.5
1
1.5
1
0.5
0
0.5
0
0
100
200
300
400
0
50
100
150
200
IO [mA]
IO [mA]
●Reference data(Input stability)
6
6
6
LDO1 Line Regulation 1.20V
5.5
LDO2 Line Regulation 2.60V
LDO3 Line Regulation 3.0V
5.5
5
5.5
5
5
4.5
4
VBAT
VBAT
VBAT
4.5
4
4.5
4
3.5
3
3.5
3
3.5
3
2.5
2
2.5
2
2.5
2
1.5
1
1.5
1
1.5
1
0.5
0
0.5
0
0.5
0
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
VBAT [V]
VBAT [V]
VBAT [V]
6
5.5
5
6
5.5
5
LDO4 Line Regulation 1.80V
LDO5 Line Regulation 3.30V
VBAT
4.5
4
4.5
4
VUSB
3.5
3
3.5
3
2.5
2
2.5
2
1.5
1
1.5
1
0.5
0
0.5
0
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
VBAT [V]
VUSB [V]
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
2011.03 - Rev.A
12/16
Technical Note
BH6172GU
●Reference data(Load transient response)
LDO1
LDO2
IO
IO
IO
IO
LDO2
LDO1
LDO1
LDO2
LDO3
LDO4
IO
IO
IO
IO
LDO3
LDO3
LDO4
LDO4
LDO5
IO
IO
LDO5
LDO5
●Reference data(Rise time)
LDO1
LDO2
EN_LD1
LDO1
EN_LD2
LDO2
LDO3
LDO4
EN_LD3
EN_LD4
LDO3
LDO4
www.rohm.com
2011.03 - Rev.A
13/16
© 2011 ROHM Co., Ltd. All rights reserved.
Technical Note
BH6172GU
●Reference data(VBAT line transient response)
LDO1
LDO2
LDO3
VBAT
VBAT
VBAT
LDO1
LDO3
LDO2
LDO4
LDO5
VBAT
VUSB
LDO5
LDO4
www.rohm.com
2011.03 - Rev.A
14/16
© 2011 ROHM Co., Ltd. All rights reserved.
Technical Note
BH6172GU
●Notes for use
(1) Absolute maximum ratings
If applied voltage (VBAT, VADP, VUSB), operating temperature range (Topr), or other absolute maximum ratings are exceeded,
there is a risk of damage. Since it is not possible to identify short, open, or other damage modes, if special modes in which
absolute maximum ratings are exceeded are assumed, consider applying fuses or other physical safety measures.
(2) Recommended operating range
This is the range within which it is possible to obtain roughly the expected characteristics. For electrical characteristics, it is
those that are guaranteed under the conditions for each parameter. Even when these are within the recommended
operating range, voltage and temperature characteristics are indicated.
(3) Reverse connection of power supply connector
There is a risk of damaging the LSI by reverse connection of the power supply connector. For protection from reverse connection,
take measures such as externally placing a diode between the power supply and the power supply pin of the LSI.
(4) Power supply lines
In the design of the board pattern, make power supply and GND line wiring low impedance. When doing so, although the
digital power supply and analog power supply are the same potential, separate the digital power supply pattern and analog
power supply pattern to deter digital noise from entering the analog power supply due to the common impedance of the
wiring patterns. Similarly take pattern design into account for GND lines as well. Furthermore, for all power supply pins of
the LSI, in conjunction with inserting capacitors between power supply and GND pins, when using electrolytic capacitors,
determine constants upon adequately confirming that capacitance loss occurring at low temperatures is not a problem for
various characteristics of the capacitors used.
(5) GND voltage
Make the potential of a GND pin such that it will be the lowest potential even if operating below that. In addition, confirm
that there are no pins for which the potential becomes less than a GND by actually including transition phenomena.
(6) Shorts between pins and misinstallation
When installing in the set board, pay adequate attention to orientation and placement discrepancies of the LSI.
If it is installed erroneously, there is a risk of LSI damage. There also is a risk of damage if it is shorted by a foreign
substance getting between pins or between a pin and a power supply or GND.
(7) Operation in strong magnetic fields
Be careful when using the LSI in a strong magnetic field, since it may malfunction.
(8) Inspection in set board
When inspecting the LSI in the set board, since there is a risk of stress to the LSI when capacitors are connected to low
impedance LSI pins, be sure to discharge for each process. Moreover, when getting it on and off of a jig in the inspection
process, always connect it after turning off the power supply, perform the inspection, and remove it after turning off the
power supply. Furthermore, as countermeasures against static electricity, use grounding in the assembly process and take
appropriate care in transport and storage.
(9) Input pins
Parasitic elements inevitably are formed on an LSI structure due to potential relationships. Because parasitic elements
operate, they give rise to interference with circuit operation and may be the cause of malfunctions as well as damage.
Accordingly, take care not to apply a lower voltage than GND to an input pin or use the LSI in other ways such that
parasitic elements operate. Moreover, do not apply a voltage to an input pin when the power supply voltage is not being
applied to the LSI. Furthermore, when the power supply voltage is being applied, make each input pin a voltage less than
the power supply voltage as well as within the guaranteed values of electrical characteristics.
(10) Ground wiring pattern
When there is a small signal GND and a large current GND, it is recommended that you separate the large current GND
pattern and small signal GND pattern and provide single point grounding at the reference point of the set so that voltage
variation due to resistance components of the pattern wiring and large currents do not cause the small signal GND voltage
to change. Take care that the GND wiring pattern of externally attached components also does not change.
(11) Externally attached capacitors
When using ceramic capacitors for externally attached capacitors, determine constants upon taking into account a
lowering of the rated capacitance due to DC bias and capacitance change due to factors such as temperature.
(12) Thermal shutdown circuit (TSD)
When the junction temperature becomes higher than a certain specific value, the thermal shutdown circuit operates and
turns the switch OFF. The thermal shutdown circuit, which is aimed at isolating the LSI from thermal runaway as much as
possible, is not aimed at the protection or guarantee of the LSI. Therefore, do not continuously use the LSI with this circuit
operating or use the LSI assuming its operation.
(13) Thermal design
Perform thermal design in which there are adequate margins by taking into account the permissible dissipation (Pd) in
actual states of use.
(14) Rush Current
Extra care must be taken on power coupling, power, ground line impedance, and PCB design while excess amount of rush
current might instantly flow through the power line when powering-up a LSI which is equipped with several power supplies,
depending on on/off sequence, and ramp delays.
www.rohm.com
2011.03 - Rev.A
15/16
© 2011 ROHM Co., Ltd. All rights reserved.
Technical Note
BH6172GU
●Ordering part number
B
H
6
1
7
2
G U
-
E
2
Part No.
Part No.
Package
GU: VCSP85H2
Packaging and forming specification
E2: Embossed tape and reel
VCSP85H2(BH6172GU)
1PIN MARK
<Tape and Reel information>
Tape
Embossed carrier tape
3000pcs
Quantity
E2
Direction
of feed
2.60 0.05
The direction is the 1pin of product is at the upper left when you hold
reel on the left hand and you pull out the tape on the right hand
(
)
S
0.06
S
φ
24- 0.3 0.05
0.05
A B
A
E
B
D
C
B
A
φ
(
0.15)INDEX POST
Direction of feed
1pin
1
2
3
4
5
P=0.5×4
0.3 0.05
Reel
Order quantity needs to be multiple of the minimum quantity.
(Unit : mm)
∗
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
2011.03 - Rev.A
16/16
Notice
N o t e s
No copying or reproduction of this document, in part or in whole, is permitted without the
consent of ROHM Co.,Ltd.
The content specified herein is subject to change for improvement without notice.
The content specified herein is for the purpose of introducing ROHM's products (hereinafter
"Products"). If you wish to use any such Product, please be sure to refer to the specifications,
which can be obtained from ROHM upon request.
Examples of application circuits, circuit constants and any other information contained herein
illustrate the standard usage and operations of the Products. The peripheral conditions must
be taken into account when designing circuits for mass production.
Great care was taken in ensuring the accuracy of the information specified in this document.
However, should you incur any damage arising from any inaccuracy or misprint of such
information, ROHM shall bear no responsibility for such damage.
The technical information specified herein is intended only to show the typical functions of and
examples of application circuits for the Products. ROHM does not grant you, explicitly or
implicitly, any license to use or exercise intellectual property or other rights held by ROHM and
other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the
use of such technical information.
The Products specified in this document are intended to be used with general-use electronic
equipment or devices (such as audio visual equipment, office-automation equipment, commu-
nication devices, electronic appliances and amusement devices).
The Products specified in this document are not designed to be radiation tolerant.
While ROHM always makes efforts to enhance the quality and reliability of its Products, a
Product may fail or malfunction for a variety of reasons.
Please be sure to implement in your equipment using the Products safety measures to guard
against the possibility of physical injury, fire or any other damage caused in the event of the
failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM
shall bear no responsibility whatsoever for your use of any Product outside of the prescribed
scope or not in accordance with the instruction manual.
The Products are not designed or manufactured to be used with any equipment, device or
system which requires an extremely high level of reliability the failure or malfunction of which
may result in a direct threat to human life or create a risk of human injury (such as a medical
instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuel-
controller or other safety device). ROHM shall bear no responsibility in any way for use of any
of the Products for the above special purposes. If a Product is intended to be used for any
such special purpose, please contact a ROHM sales representative before purchasing.
If you intend to export or ship overseas any Product or technology specified herein that may
be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to
obtain a license or permit under the Law.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact us.
ROHM Customer Support System
http://www.rohm.com/contact/
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
R1120
A
相关型号:
BH6176GU-E2
Power Supply Support Circuit, Adjustable, 6 Channel, CMOS, PBGA25, 2.60 X 2.60 MM, ROHS COMPLIANT, VCSP-25
ROHM
BH6176GU_11
Silicon Monolithic Integrated Circuit Power Management LSI for MultiMedia LSI on Cellular
ROHM
©2020 ICPDF网 联系我们和版权申明