BP3622 [ROHM]
ROHM的13.56MHz无线充电模块是面向小型传感设备和可穿戴设备设计而成的。可实现Qi标准难以实现的超小型设备的无线充电功能。13.56MHz是与NFC通信协议相同的频段,因此可以共用NFC通信天线进行供电。通过成对使用已完成天线设计和匹配调试的BP3621(发射)和BP3622(接收)模块,可以大大缩短天线设计和匹配调试的开发时间。;型号: | BP3622 |
厂家: | ROHM |
描述: | ROHM的13.56MHz无线充电模块是面向小型传感设备和可穿戴设备设计而成的。可实现Qi标准难以实现的超小型设备的无线充电功能。13.56MHz是与NFC通信协议相同的频段,因此可以共用NFC通信天线进行供电。通过成对使用已完成天线设计和匹配调试的BP3621(发射)和BP3622(接收)模块,可以大大缩短天线设计和匹配调试的开发时间。 通信 无线 |
文件: | 总21页 (文件大小:1193K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Wireless Charger Module
13.56 MHz Wireless Charger Module
BP3622
General Description
Package
BP3622 is a compact wireless charger module with
integrated antenna board.
Features
- Wireless power receiver
W (Typ.) × D (Typ.) × H (Typ.)
24.0 mm × 17.0 mm × 1.5 mm
- Optimized for wireless charging with BP3621
- 212 kbps wireless communication
Major Performance
Parameter
Description
Power supply
Antenna size
Board
Max 200 mW (d = 10.0 mm)
16.0 mm × 16.0 mm
FR-4, t = 0.4 mm
Parts are mounted on one side
0.5 mm pitch / 8 pin FPC connector
0.38 g
Host interface
Weight
Block Diagram
BP3622
ISO_V
RFDET
P12
SDA_S
SCL_S
BAT
Matching
Circuit
Wireless
Charger
LSI
Flexible
Cable
Antenna coil
Connector
Diode
INT_S
GND
Bridge
Figure 1. Block Diagram
www.rohm.com
© 2021 ROHM Co., Ltd. All rights reserved.
TSZ22111・14・001
TSZ02201-BP3622-1-2
15.Sep.2021 – Rev.001
1/18
Datasheet
BP3622
1. Absolute Maximum Ratings
No.
Parameter
Symbol
Rating
Unit
Condition
Ta=25 ºC
1
2
3
4
Input Voltage
VDD
VDIN
Ii
-0.3 to +6.5
-0.3 to VDD + 0.3
-10 to +10
V
V
Input Voltage (Digital IO *1)
Input Current (Digital IO *1)
Output Voltage (Digital IO *1)
Ta=25 ºC
Ta=25 ºC
Ta=25 ºC
Humidity:
mA
V
VDO
-0.3 to VDD + 0.3
5
6
Operating temperature range
Storage temperature range
Topr
-10 to +50
-20 to +50
ºC
ºC
35 % to 85 %RH
No dew condensation
Humidity:
Tstg
35 % to 85 %RH
No dew condensation
(*1) Digital IO: P12, RFDET, INT_S, SCL_S, SDA_S
(Note) The absolute maximum ratings represent values that shall not be exceeded for even an instant on all operating
or testing conditions. Design systems with a margin for the ratings listed above.
(Note) This module can be operated only in combination with BP3621. Operation with other systems is not
guaranteed.
www.rohm.com
© 2021 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ2201-BP3622-1-2
2/18
15.Sep.2021 – Rev.001
Datasheet
BP3622
2. Recommended Operating Conditions
Specification
No.
Parameter
Symbol
Unit
Condition
Min.
-10
-
Typ.
25
Max.
1
2
3
Operating temperature range
Distance between Antennas
Load resistance
Topr
Dant
Rload
50
-
ºC
mm
Ω
10.0
-
*1
*2
100
200
(*1) The power feeding antenna and the power receiving antenna should face each other horizontally.
See Figure 5 and Figure 6 for reference.
(*2) See Figure 2 and Figure 3 for reference.
www.rohm.com
© 2021 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ2201-BP3622-1-2
3/18
15.Sep.2021 – Rev.001
Datasheet
BP3622
3. Electrical Characteristics
DC Function
(Ta=25 ºC)
Specification
Typ.
No.
1
Parameter
Symbol
Unit
Condition
Min.
Max.
VDD
-
VOH
VOL
-
-
-
-
V
V
V
Output Voltage
0.5
(INT_S, SDA_S, RFDET)
-
0.4
VDD
0.7
VIH1
×VDD
Input Voltage
2
(SCL_S, SDA_S, P12)
0.3 ×
VDD
VIL1
0
-
V
(*1) P12 settled “Pull Up Input, Detect High signal”.
“Pull Up” is done in this module.
“Pull Up” voltage depends on the power supplied from BP3621. (1.8 V to 5.5 V)
“Pull Up” resistance value is typ. 100 kΩ.
Power Supply Characteristics
(Ta=25 ºC)
Condition
Specification
No.
Parameter
Symbol
Unit
Min.
Typ.
200
Max.
1
2
Output Power *1
Output Voltage *1*2
WBAT
VBAT
-
-
mW
V
4.5
-
5.5
(*1) During power supply from BP3621.
(*2) Set the load resistance value so that the output voltage does not fall below 4.5 V.
(Note) The characteristics of this module are ensured when using a BP3621 with a matching capacitor (optimized
matching constant) as the power feeding system.
www.rohm.com
© 2021 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ2201-BP3622-1-2
4/18
15.Sep.2021 – Rev.001
Datasheet
BP3622
4. Typical Performance Curves
Lower limit under each condition
Upper limit
240
220
200
180
160
140
120
100
BP3621 VDD=5.5V
BP3621 VDD=5.0V
BP3621 VDD=4.5V
80
100
120
140
160
180
200
220
Load resistance [Ω]
Figure 2. Output Power vs Load resistance
Lower limit under each condition
Upper limit
5.2
5.1
5.0
4.9
4.8
4.7
4.6
4.5
BP3621 VDD=5.5V
BP3621 VDD=5.0V
BP3621 VDD=4.5V
80
100
120
140
160
180
200
220
Load resistance [Ω]
Figure 3. Output Voltage vs Load resistance
www.rohm.com
© 2021 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ2201-BP3622-1-2
5/18
15.Sep.2021 – Rev.001
Datasheet
BP3622
45
40
35
30
25
20
15
10
5
BP3621 VDD=5.5V
BP3621 VDD=5.0V
BP3621 VDD=4.5V
0
0
50
100
150
200
Elapsed time [s]
Figure 4. Surface temperature of IC vs Elapsed time
www.rohm.com
© 2021 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ2201-BP3622-1-2
6/18
15.Sep.2021 – Rev.001
Datasheet
BP3622
Antenna center
BP3621
BP3622
Available feeding range = 7mm @Load resistance = 120 Ω
Available feeding range = 10mm @Load resistance = 200 Ω
Figure 5. Available feeding range (Top view)
4mm
BP3622
Antenna center
Available feeding area @Load resistance = 200 Ω
BP3621
4mm
10mm
Figure 6. Available feeding area (Side view)
www.rohm.com
© 2021 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ2201-BP3622-1-2
7/18
15.Sep.2021 – Rev.001
Datasheet
BP3622
5. I2C AC Function
(Standard mode: 100 kHz, Ta=25 ºC)
Specification
No.
1
Parameter
Symbol
fSCL
Unit
kHz
µs
Condition
Min.
Typ.
Max.
100
SCL_S clock frequency
SCL_S hold time
-
-
2
tHD:STA
4.0
-
-
(start/repeated start condition)
SCL_S “L” level time
SCL_S “H” level time
SCL_S setup time
3
4
tLOW
4.7
4.0
-
-
-
-
µs
µs
tHIGH
5
tSU:STA
4.7
-
-
µs
(repeated start condition)
SDA_S hold time
6
7
tHD:DAT
tSU:DAT
0
-
-
-
-
µs
µs
SDA_S setup time
0.25
SDA_S setup time
8
9
tSU:STO
tBUF
4.0
4.7
-
-
-
-
µs
µs
(P: Stop condition)
Bus free time
(Fast mode: 400 kHz, Ta=25 ºC)
Specification
No.
1
Parameter
Symbol
fSCL
Unit
kHz
µs
Condition
Min.
Typ.
Max.
400
SCL_S clock frequency
SCL_S hold time
-
-
2
tHD:STA
0.6
-
-
(start/repeated start condition)
SCL_S “L” level time
SCL_S “H” level time
SCL_S setup time
3
4
tLOW
1.3
0.6
-
-
-
-
µs
µs
tHIGH
5
tSU:STA
0.6
-
-
µs
(repeated start condition)
SDA_S hold time
6
7
tHD:DAT
tSU:DAT
0
-
-
-
-
µs
µs
SDA_S setup time
0.1
SDA_S setup time
8
9
tSU:STO
tBUF
0.6
1.3
-
-
-
-
µs
µs
(P: Stop condition)
Bus free time
www.rohm.com
© 2021 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ2201-BP3622-1-2
8/18
15.Sep.2021 – Rev.001
Datasheet
BP3622
6. Operation Flow
When BP3621 detects BP3622, it starts pre-charge operation and charge operation.
Check if a TAG is BP3622
BP3621
BP3622
Figure 7. Operation Flow
BP3621/BP3622 has three functions for controlling the power supply.
1.Communication function (Communication) BP3621 checks the response from BP3622 to determine
whether the power is supplied. Then, BP3621 receives the state of BP3622 and checks the power
supply change request and full charge status.
2.Power Supply Function (Power Transfer) BP3621 transfers power to BP3622.
3.Notification function (Notify) BP3622 requests to communicate with BP3621 to notify a power
supply change request or abnormal condition detection during power supply.
www.rohm.com
© 2021 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ2201-BP3622-1-2
15.Sep.2021 – Rev.001
9/18
Datasheet
BP3622
7. Physical Dimension
The antenna pattern is drawn on the back of the component mounting side.
Direction to face BP3621
Antenna Center
Flexible Cable Connector
Unit: mm
Figure 8. Physical Dimension
(Note) Dimensions without tolerances are for reference only.
(Note) When the product is shipped, the actuator of the connector is open. The height dimension is when the actuator
is closed.
www.rohm.com
© 2021 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ2201-BP3622-1-2
10/18
15.Sep.2021 – Rev.001
Datasheet
BP3622
8. Precautions for Installation
1. This module has an antenna on the side opposite to the component mounting side.
2. Use the power feeding side antenna facing the antenna side of this module.
3. Align the center of the antenna of this module with the center of the power feeding antenna.
4. Attach double-sided tape to the antenna side and attach it to any position.
(Double-sided tape is not included with this product.)
5. Do not block the magnetic flux between the antennas.
6. This module is equipped with Hirose FH34SRJ-8S-0.5SH(50) as a flexible cable connector.
(Flexible cable is not included with this product.)
www.rohm.com
© 2021 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ2201-BP3622-1-2
11/18
15.Sep.2021 – Rev.001
Datasheet
BP3622
9. Pin Descriptions
1
8
Flexible cable
insertion direction
Figure 9. Pin Number (flexible cable connector)
Connections for unused pins
Open
Pin No.
1
Pin Name
I/O
-
Function
ISO_V
Logic IO voltage
RF signal detection output
- Hi-Z: No Active
2
RFDET
O
Open
- Low: Active after Power on and finish the
initial setting
Charger IC status input
- Pull Up Input, Detect High signal
I2C serial data access
I2C clock
3
P12 *1
I
GND
4
5
6
SDA_S
SCL_S
BAT
I/O
I
Open
Open
-
O
Power output
Interrupt information output
- High: No Active
7
8
INT_S
GND
O
-
Open
- Low: Active when an interrupt occurs
Ground
-
(*1) When “Low” voltage is input to the P12 pin, power is output from the BAT pin.
www.rohm.com
© 2021 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ2201-BP3622-1-2
12/18
15.Sep.2021 – Rev.001
Datasheet
BP3622
10. PCB Marking Specification
Unit: mm
Figure 10. PCB Marking Specification
Marking
137*▲▲▲▼: Production Lot Number (8 digits)
↓
(Example) 137 → Year 2021, Week 37, *▲▲▲▼ (internal serial number)
www.rohm.com
© 2021 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ2201-BP3622-1-2
13/18
15.Sep.2021 – Rev.001
Datasheet
BP3622
11. Reference Circuit
Figure 11. Reference Circuit Diagram
www.rohm.com
© 2021 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ2201-BP3622-1-2
14/18
15.Sep.2021 – Rev.001
Datasheet
BP3622
12. Packing Specification
12.1 Packing Method
25 pieces of products are packaged in the packaging tray, and it is piled up 12 steps to make 300 pieces with an empty
tray on the top, and it is packed into the packaging case.
The number of piling might change according to the quantity of delivery without previous notice.
Packaging tray
Fixed by adhesive cellophane tape.
Packaging trays are rotated 180 degrees
and stacked alternately.
BP3622: 25 pieces
Fixed by adhesive cellophane tape.
Packaging case
Figure 12. Packing Method
www.rohm.com
© 2021 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ2201-BP3622-1-2
15/18
15.Sep.2021 – Rev.001
Datasheet
BP3622
12.2 Label Indication
The label with following things is stuck at the packing case.
1
2
3
4
5
6
7
Type name (BP3622)
Quantity
Lot No.
Shipment inspection stamp
Country of origin
Manufacturing company name (Trade mark)
Logotype of lead free
Please refer to the following example of the label indication.
(a) For products of ROHM APOLLO
(b) For products of ROHM INTEGRATED SYSTEMS (THAILAND)
Figure 13. Label Indication
www.rohm.com
© 2021 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ2201-BP3622-1-2
16/18
15.Sep.2021 – Rev.001
Datasheet
BP3622
13. Product Weight
0.38 g (Typ.)
14. Manufacturing Country
JAPAN
THAILAND
15. Notice
● Precaution on using this Product
1) This Product may be subjected to radio wave interference from other equipment emitting radio waves.
2) This Product emits radio waves due to the specification. To use equipment emitting radio waves, certification
under the Radio Act should be obtained by region in which the Product is used. For the standards for certification
under the Radio Act to be obtained for the use of this Product, separately contact your ROHM representative.
www.rohm.com
© 2021 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ2201-BP3622-1-2
17/18
15.Sep.2021 – Rev.001
Datasheet
BP3622
16. Revision History
Rev.
001
Date
15.Sep.2021
Contents
New Issue
www.rohm.com
© 2021 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ2201-BP3622-1-2
18/18
15.Sep.2021 – Rev.001
Notice
Precaution on using ROHM Products
1. Our Products are designed and manufactured for application in ordinary electronic equipment (such as AV equipment,
OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you
intend to use our Products in devices requiring extremely high reliability (such as medical equipment (Note 1), transport
equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car
accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or
serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance.
Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any
damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific
Applications.
(Note1) Medical Equipment Classification of the Specific Applications
JAPAN
USA
EU
CHINA
CLASSⅢ
CLASSⅣ
CLASSⅡb
CLASSⅢ
CLASSⅢ
CLASSⅢ
2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3. Our Products are designed and manufactured for use under standard conditions and not under any special or
extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any
special or extraordinary environments or conditions. If you intend to use our Products under any special or
extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of
product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (Exclude cases where no-clean type fluxes is used.
However, recommend sufficiently about the residue.) ; or Washing our Products by using water or water-soluble
cleaning agents for cleaning residue after soldering
[h] Use of the Products in places subject to dew condensation
4. The Products are not subject to radiation-proof design.
5. Please verify and confirm characteristics of the final or mounted products in using the Products.
6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse, is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7. De-rate Power Dissipation depending on ambient temperature. When used in sealed area, confirm that it is the use in
the range that does not exceed the maximum junction temperature.
8. Confirm that operation temperature is within the specified range described in the product specification.
9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
Precaution for Mounting / Circuit board design
1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must
be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products,
please consult with the ROHM representative in advance.
For details, please refer to ROHM Mounting specification
Notice-PGA-E
Rev.004
© 2015 ROHM Co., Ltd. All rights reserved.
Precautions Regarding Application Examples and External Circuits
1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the
characteristics of the Products and external components, including transient characteristics, as well as static
characteristics.
2. You agree that application notes, reference designs, and associated data and information contained in this document
are presented only as guidance for Products use. Therefore, in case you use such information, you are solely
responsible for it and you must exercise your own independent verification and judgment in the use of such information
contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses
incurred by you or third parties arising from the use of such information.
Precaution for Electrostatic
This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper
caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be
applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,
isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).
Precaution for Storage / Transportation
1. Product performance and soldered connections may deteriorate if the Products are stored in the places where:
[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2
[b] the temperature or humidity exceeds those recommended by ROHM
[c] the Products are exposed to direct sunshine or condensation
[d] the Products are exposed to high Electrostatic
2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period
may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is
exceeding the recommended storage time period.
3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads
may occur due to excessive stress applied when dropping of a carton.
4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of
which storage time is exceeding the recommended storage time period.
Precaution for Product Label
A two-dimensional barcode printed on ROHM Products label is for ROHM’s internal use only.
Precaution for Disposition
When disposing Products please dispose them properly using an authorized industry waste company.
Precaution for Foreign Exchange and Foreign Trade act
Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign
trade act, please consult with ROHM in case of export.
Precaution Regarding Intellectual Property Rights
1. All information and data including but not limited to application example contained in this document is for reference
only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any
other rights of any third party regarding such information or data.
2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the
Products with other articles such as components, circuits, systems or external equipment (including software).
3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any
third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM
will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to
manufacture or sell products containing the Products, subject to the terms and conditions herein.
Other Precaution
1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.
2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written
consent of ROHM.
3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the
Products or this document for any military purposes, including but not limited to, the development of mass-destruction
weapons.
4. The proper names of companies or products described in this document are trademarks or registered trademarks of
ROHM, its affiliated companies or third parties.
Notice-PGA-E
Rev.004
© 2015 ROHM Co., Ltd. All rights reserved.
Daattaasshheeeett
General Precaution
1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents.
ROHM shall not be in an y way responsible or liable for failure, malfunction or accident arising from the use of a ny
ROHM’s Products against warning, caution or note contained in this document.
2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior
notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s
representative.
3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all
information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or
liable for any damages, expenses or losses incurred by you or third parties resulting from inaccuracy or errors of or
concerning such information.
Notice – WE
Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明