ESR03EZPD1002 [ROHM]

Fixed Resistor, Metal Glaze/thick Film, 0.25W, 10000ohm, 150V, 0.5% +/-Tol, 100ppm/Cel, Surface Mount, 0603, CHIP;


型号：	ESR03EZPD1002
厂家：	ROHM
描述：	Fixed Resistor, Metal Glaze/thick Film, 0.25W, 10000ohm, 150V, 0.5% +/-Tol, 100ppm/Cel, Surface Mount, 0603, CHIP 电阻器
文件：	总4页 (文件大小：148K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

Anti-surge thick film chip resistor

ESR03 (0603 size : 1 / 5W)

zFeatures

1) Power rating of 1 / 5W (MCR03 1/10W)

2) Superior anti surge to MCR series

3) Highly reliable chip resistor

Ruthenium oxide dielectric offers superior resistance to the elements.

4) ROHM resistors have approved ISO–9001, ISO/TS 16949 certification.

Design and specifications are subject to change without notice. Carefully check the specification sheet before using or

ordering it.

zApplications

Automotive, LCD Monitor, projector, power supply, charger, inverter and so on.

zRatings

Item

Conditions

Specifications

0.2W (1/5W)

Rated power

Power must be derated according to the power derating curve in

Figure 1 when ambient temperature exceeds 70°C.

at 70°C

100

−55

100

155

AMBIENT TEMPERATURE (°C)

Fig.1

Rated voltage

The voltage rating is calculated by the following equation.

If the value obtained exceeds the limiting element voltage,

the voltage rating is equal to the maximum operating voltage.

E: Rated voltage (V)

P: Rated power (W)

E= P×R

R: Nominal resistance (Ω)

Limiting element voltage

50V

Nominal resistance

See Table 1.

Operating temperature

−55°C to +155°C

Table 1

Resistance range

Resistance temperature coefficient

Resistance tolerance

(Ω)

(ppm/°C)

D ( 0.5%)

10 ≤ R ≤ 1M

1 ≤ R ≤ 10M

100

200

(E24)

( 1%)

( 5%)

1 ≤ R ≤ 10M (E24)

zBefore using components in circuits where they will be exposed to transients such as pulse loads (short–duration, high– level

loads), be certain to evaluate the component in the mounted state. In addition, the reliability and performance of this

component cannot be guaranteed if it is used with a steady state voltage that is greater than its rated voltage.

www.rohm.com

2009.10 - Rev.C

1/3

ESR03

Data Sheet

Characteristics

Guaranteed value

Resistor type

Item

Test conditions (JIS C 5201-1)

JIS C 5201-1 4.5

J : 5%

Resistance

F : 1%

D : 0.5%

Variation of resistance

with temperature

JIS C 5201-1 4.8

Measurement : −55 / +25 / +125°C

See Table.1

JIS C 5201-1 4.13

Rated voltage (current) ×2.5, 2s.

Maximum overload voltage : 100V

Overload

(2.0%+0.1Ω)

A new uniform coating of minimum of

95% of the surface being immersed

and no soldering damage.

JIS C 5201-1 4.17

Rosin·Ethanol (25%WT)

Soldering condition : 235 5°C

Duration of immersion : 2.0 0.5s.

Solderability

(1.0%+0.05Ω)

No remarkable abnormality on the appearance.

JIS C 5201-1 4.18

Soldering condition : 260 5°C

Duration of immersion : 10 1s.

Resistance to

soldering heat

(1.0%+0.05Ω)

(3.0%+0.1Ω)

JIS C 5201-1 4.19

Test temp. : −55°C to +125°C 5cyc

Rapid change of

temperature

JIS C 5201-1 4.24

40°C, 93%RH

Test time : 1,000h to 1,048h

Damp heat, steady state

(3.0%+0.1Ω)

JIS C 5201-1 4.25.1

Rated voltage (current), 70°C

1.5h : ON − 0.5h : OFF

Test time : 1,000h to 1,048h

Endurance at 70°C

(3.0%+0.1Ω)

(1.0%+0.05Ω)

JIS C 5201-1 4.25.3

155°C

Endurance

Test time : 1,000h to 1,048h

JIS C 5201-1 4.29

23 5°C, Immersion cleaning, 5 0.5min.

Solvent : 2-propanol

Resistance to solvent

(1.0%+0.05Ω)

Without mechanical damage such as breaks.

JIS C 5201-1 4.33

Bend strength of

the end face plating

(5.0%+0.05Ω)

EIAJ ED-4701 1300 Test method 304

Voltage : 3kv

Static electric

characteristics

R : 1.5kΩ

C : 100pF

Apply cycle : 1 time

zDimensions (Unit : mm)

0.3 0.2

No.

Material

Resistive element (Oxide metal thick film)

Silver thick film electrode

0.3 0.2

1.6 0.1

Nickel electrode

Sn electrode

Alumina substrate

Overcoating (Resin)

Marking

www.rohm.com

2009.10 - Rev.C

2/3

ESR03

Data Sheet

Packaging

Reel

Taping

Heat crimp cover / Tape

Thick paper

mount

Chip resistor Square punchout hole

(Underside paper tape)

Label

(Unit : mm)

EIAJ ET-7200B compliant

3.5 0.05

8.0 0.3

1.75 0.1

1.1 0.1

1.9 0.1

(Unit: mm)

+0.1

−1.5

+1.0

1.5

4.0 0.1

2.0 0.05

Max. 1.1

φ180

φ60

φ13 0.2

zPart No. Explanation

E S R 0 3 E Z P

Part No.

Resistance tolerance

Nominal resistance

Resistance code, 3 or 4 digits.

Resistance

tolerance

Resistance

code

0.5%

3 digits

4 digits

Packaging Specifications Code

Resistance tolerance

J( 5%) F( 1%) D( 0.5%)

Part No.

Code

Packaging specifications

Paper tape (4mm Pitch)

Reel

Basic ordering unit(pcs)

5,000

ESR03

EZP

φ180mm (7inch)

Reel (φ180mm) : Compatible with JEITA standard "EIAJ ET-7200B"

: Standard product

www.rohm.com

2009.10 - Rev.C

3/3

Notice

N o t e s

No copying or reproduction of this document, in part or in whole, is permitted without the

consent of ROHM Co.,Ltd.

The content speciﬁed herein is subject to change for improvement without notice.

The content speciﬁed herein is for the purpose of introducing ROHM's products (hereinafter

"Products"). If you wish to use any such Product, please be sure to refer to the speciﬁcations,

which can be obtained from ROHM upon request.

Examples of application circuits, circuit constants and any other information contained herein

illustrate the standard usage and operations of the Products. The peripheral conditions must

be taken into account when designing circuits for mass production.

Great care was taken in ensuring the accuracy of the information speciﬁed in this document.

However, should you incur any damage arising from any inaccuracy or misprint of such

information, ROHM shall bear no responsibility for such damage.

The technical information speciﬁed herein is intended only to show the typical functions of and

examples of application circuits for the Products. ROHM does not grant you, explicitly or

implicitly, any license to use or exercise intellectual property or other rights held by ROHM and

other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the

use of such technical information.

The Products speciﬁed in this document are intended to be used with general-use electronic

equipment or devices (such as audio visual equipment, ofﬁce-automation equipment, commu-

nication devices, electronic appliances and amusement devices).

The Products speciﬁed in this document are not designed to be radiation tolerant.

While ROHM always makes efforts to enhance the quality and reliability of its Products, a

Product may fail or malfunction for a variety of reasons.

Please be sure to implement in your equipment using the Products safety measures to guard

against the possibility of physical injury, ﬁre or any other damage caused in the event of the

failure of any Product, such as derating, redundancy, ﬁre control and fail-safe designs. ROHM

shall bear no responsibility whatsoever for your use of any Product outside of the prescribed

scope or not in accordance with the instruction manual.

The Products are not designed or manufactured to be used with any equipment, device or

system which requires an extremely high level of reliability the failure or malfunction of which

may result in a direct threat to human life or create a risk of human injury (such as a medical

instrument, transportation equipment, aerospace machinery, nuclear-reactor controller,

fuel-controller or other safety device). ROHM shall bear no responsibility in any way for use of

any of the Products for the above special purposes. If a Product is intended to be used for any

such special purpose, please contact a ROHM sales representative before purchasing.

If you intend to export or ship overseas any Product or technology speciﬁed herein that may

be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to

obtain a license or permit under the Law.

Thank you for your accessing to ROHM product informations.

More detail product informations and catalogs are available, please contact us.

ROHM Customer Support System

http://www.rohm.com/contact/

www.rohm.com

R0039

相关型号：