ESR10EZPD82R5 [ROHM]

Fixed Resistor, Metal Glaze/thick Film, 0.25W, 82.5ohm, 150V, 0.5% +/-Tol, 100ppm/Cel, Surface Mount, 0805, CHIP;


型号：	ESR10EZPD82R5
厂家：	ROHM
描述：	Fixed Resistor, Metal Glaze/thick Film, 0.25W, 82.5ohm, 150V, 0.5% +/-Tol, 100ppm/Cel, Surface Mount, 0805, CHIP 电阻器
文件：	总7页 (文件大小：106K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

ESR10

Resistors

Endured surge thick film chip resistor

ESR10 (2012 size : 1 / 4W)

zFeatures

1) Power rating of 1 / 4W (Rated power is more than twice that of MCR series)

2) Superior anti surge to MCR series

3) Highly reliable chip resistor

Ruthenium oxide dielectric offers superior resistance to the elements.

4) ROHM resistors have approved ISO–9001 certification.

Design and specifications are subject to change without notice. Carefully check the specification sheet before using or

ordering it.

zRatings

Item

Conditions

Specifications

0.25W (1 / 4W)

Rated power

Power must be derated according to the power derating curve in

Figure 1 when ambient temperature exceeds 70°C.

at 70°C

100

−55

100

155

AMBIENT TEMPERATURE (°C)

Fig.1

Rated voltage

The voltage rating is calculated by the following equation.

If the value obtained exceeds the limiting element voltage,

the voltage rating is equal to the maximum operating voltage.

E: Rated voltage (V)

P: Rated power (W)

E= P×R

R: Nominal resistance (Ω)

Limiting element voltage

150V

Nominal resistance

See Table 1.

Operating temperature

−55°

C to +155°C

1/6

ESR10

Resistors

Table 1

Resistance range

Resistance temperature coefficient

Resistance tolerance

(Ω)

(ppm/°C)

D ( 0.5%)

10 ≤ R ≤ 1M

5.6 ≤ R ≤ 10M (E24)

100

200

(E24,96)

( 5%)

zBefore using components in circuits where they will be exposed to transients such as pulse loads (short–duration, high– level loads), be certain to evaluate the

component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that

is greater than its rated voltage.

Characteristics

Guaranteed value

Resistor type

Item

Resistance

Test conditions (JIS C 5201-1)

JIS C 5201-1 4.5

J : 5%

D : 0.5%

Variation of resistance

with temperature

JIS C 5201-1 4.8

Measurement : −55 / +25 / +125°C

See Table.1

JIS C 5201-1 4.13

Rated voltage (current) ×2.5, 2s.

Maximum overload voltage : 200V

Overload

(2.0%+0.1Ω)

A new uniform coating of minimum of

95% of the surface being immersed

and no soldering damage.

JIS C 5201-1 4.17

Rosin·Ethanol (25%WT)

Soldering condition : 235 5°C

Duration of immersion : 2.0 0.5s.

Solderability

(1.0%+0.05Ω)

No remarkable abnormality on the appearance.

JIS C 5201-1 4.18

Soldering condition : 260 5°C

Duration of immersion : 10 1s.

Resistance to

soldering heat

(1.0%+0.05Ω)

(3.0%+0.1Ω)

JIS C 5201-1 4.19

Test temp. : −55°C to +125°C 5cyc

Rapid change of

temperature

JIS C 5201-1 4.24

40°C, 93%RH

Test time : 1,000h to 1,048h

Damp heat, steady state

(3.0%+0.1Ω)

JIS C 5201-1 4.25.1

Rated voltage (current), 70°C

1.5h : ON − 0.5h : OFF

Test time : 1,000h to 1,048h

Endurance at 70°C

(3.0%+0.1Ω)

(1.0%+0.05Ω)

JIS C 5201-1 4.25.3

155°C

Endurance

Test time : 1,000h to 1,048h

JIS C 5201-1 4.29

23 5°C, Immersion cleaning, 5 0.5min.

Solvent : 2-propanol

Resistance to solvent

(1.0%+0.05Ω)

Without mechanical damage such as breaks.

JIS C 5201-1 4.33

Bend strength of

the end face plating

(5.0%+0.05Ω)

EIAJ ED-4701 1300 Test method 304

Voltage : 3kv

Static electric

characteristics

R : 1.5kΩ

C : 100pF

Apply cycle : 1 time

2/6

ESR10

Resistors

zExternal dimensions (Unit : mm)

0.4 0.2

No.

Material

Resistive element

0.4 0.2

2.0 0.1

Silver thick film electrode

Nickel electrode

Sn electrode

Alumina substrate

Overcoating

Packaging

Reel

Taping

φD0

Heat crimp cover/Tape

(Underside paper tape)

Thick paper

mount

Chip resistor Square punchout hole

(Unit: mm)

Label

EIAJ ET-7200B compliant

+0.2

−0.1

+0.2

−0.1

8.0±0.3

3.5±0.05

1.75±0.1

1.65

2.4

(Unit: mm)

+0.1

4.0±0.1

2.0±0.05

Max. 1.1

φ1.5

−1.5

+1.0

φ180

φ60

φ13 0.2

3/6

ESR10

Resistors

zPart designation

3-digit or 4-digit IEC coding system

Part No.

Nominal resistance

Packaging / Processing specifications

Resistance tolerance

Standard ordering

Unit(pcs)

0.5%

Part No. Code

Packaging

Paper tape

ESR10

EZP

5,000

zDimensions

2.20

2.15

2.10

2.05

2.00

1.95

1.90

1.85

1.80

1.45

1.40

1.35

1.30

1.25

1.20

1.15

1.10

1.05

0.75

JIS C 5201-1 SEC 4.4

SAMPLE SIZE : n=20pcs

MICROMETER

JIS C 5201-1 SEC 4.4

SAMPLE SIZE : n=20pcs

MICROMETER

JIS C 5201-1 SEC 4.4

SAMPLE SIZE : n=20pcs

MICROMETER

0.70

0.65

0.60

0.55

0.50

0.45

0.40

0.35

10 100 1k 10k 100k 1M 10M

100

1k 10k 100k 1M 10M

RESISTANCE (Ω)

Fig.2 Dimensions (length)

Fig.3 Dimensions (width)

Fig.4 Dimensions (thickness)

Electrical characteristics

6.0

4.0

500

400

300

200

100

JIS C 5201-1 SEC 4.8

SAMPLE SIZE : n=10pcs

25°C / −55°C

JIS C 5201-1 SEC 4.5

SAMPLE SIZE : n=20pcs

20°C 65%RH

JIS C 5201-1 SEC 4.5

SAMPLE SIZE : n=20pcs

20°C 65%RH

4.0

25°C / 125°C

2.0

0.0

2.0

0.0

−100

−200

−300

−2.0

−4.0

−6.0

−2.0

−4.0

−6.0

−400

−500

10 100 1k

10k 100k 1M 10M

10 100 1k 10k 100k 1M 10M

100

10k 100k 1M

RESISTANCE (Ω)

Fig.7 Variation of resistance with

temperature (J class)

Fig.5 Resistance (J class)

Fig.6 Resistance (D class)

4/6

ESR10

Resistors

500

400

300

200

100

5.0

4.0

3.0

2.0

1.0

0.0

JIS C 5201-1 SEC 4.8

SAMPLE SIZE : n=10pcs

25°C / −55°C

JIS C 5201-1 SEC 4.13

SAMPLE SIZE : n=10pcs

RATED VOLTAGE×2.5

TIMES : 2s

25°C / 125°C

MAXIMUM OVERLOAD VOLTAGE : 200V

−1.0

−2.0

−3.0

−4.0

−5.0

−100

−200

−300

JIS C 5201-1 SEC 4.17

SAMPLE SIZE : n=10pcs

SOLDERING CONDITION : 235°C 2s

−400

−500

10 100 1k 10k 100k 1M 10M

100

10k 100k

10 100 1k 10k 100k 1M 10M

RESISTANCE (Ω)

Fig.9 Overload

Fig.8 Variation of resistance with

temperature (D class)

Fig.10 Solderability

2.5

4.0

3.0

JIS C 5201-1 SEC 4.19

SAMPLE SIZE : n=10pcs

−55°C / 125°C 1000cyc

JIS C 5201-1 SEC 4.24

SAMPLE SIZE : n=10pcs

40°C 93%RH WITH NO LOAD 1,000h

JIS C 5201-1 SEC 4.18

SAMPLE SIZE : n=10pcs

SOLDERING CONDITION : 260°C 10s

2.0

1.5

1.0

0.5

0.0

2.0

1.5

1.0

0.5

0.0

2.0

1.0

0.0

−0.5

−1.0

−1.5

−0.5

−1.0

−1.5

−1.0

−2.0

−3.0

−4.0

−2.0

−2.5

−2.0

−2.5

10 100 1k 10k 100k 1M 10M

RESISTANCE (Ω)

Fig.12 Rapid change of temperature

Fig.11 Resistance to soldering heat

Fig.13 Damp heat, steady state

4.0

3.0

4.0

3.0

2.0

1.5

JIS C 5201-1 SEC 4.25.1

SAMPLE SIZE : n=10pcs

70°C 1,000h

JIS C 5201-1 SEC 4.25.3

SAMPLE SIZE : n=10pcs

155°C WITH NO LOAD 1,000h

JIS C 5201-1 SEC 4.29

SAMPLE SIZE : n=10pcs

IPA, 5min.

THE RATED VOLTAGE 1.5h on, 0.5h off

2.0

1.0

0.5

0.0

−1.0

−2.0

−3.0

−4.0

−1.0

−2.0

−3.0

−4.0

−0.5

−1.0

−1.5

−2.0

10 100 1k 10k 100k 1M 10M

RESISTANCE (Ω)

Fig.14 Endurance at 70°C

Fig.15 Endurance

Fig.16 Component solvent resistance

5/6

ESR10

Resistors

2.5

10.0

EIAJ ED-4701/300

VOLTAGE : 3kV

R : 1.5kΩ C : 100pF

APPLY CYCLE : 1TIME

JIS C 5201-1 SEC 4.33

SAMPLE SIZE : n=10pcs

ENDURANCE WITH 90mm WIDTH

2.0

1.5

1.0

0.5

0.0

5.0

0.0

−0.5

−1.0

−1.5

−5.0

−2.0

−2.5

−10.0

10 100 1k 10k 100k 1M 10M

RESISTANCE (Ω)

Fig.17 Bend strength of the end

face plating

Fig.18 Static electric aharacteristics

6/6

Appendix

Notes

No technical content pages of this document may be reproduced in any form or transmitted by any

means without prior permission of ROHM CO.,LTD.

The contents described herein are subject to change without notice. The specifications for the

product described in this document are for reference only. Upon actual use, therefore, please request

that specifications to be separately delivered.

Application circuit diagrams and circuit constants contained herein are shown as examples of standard

use and operation. Please pay careful attention to the peripheral conditions when designing circuits

and deciding upon circuit constants in the set.

Any data, including, but not limited to application circuit diagrams information, described herein

are intended only as illustrations of such devices and not as the specifications for such devices. ROHM

CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any

third party's intellectual property rights or other proprietary rights, and further, assumes no liability of

whatsoever nature in the event of any such infringement, or arising from or connected with or related

to the use of such devices.

Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or

otherwise dispose of the same, no express or implied right or license to practice or commercially

exploit any intellectual property rights or other proprietary rights owned or controlled by

ROHM CO., LTD. is granted to any such buyer.

Products listed in this document are no antiradiation design.

The products listed in this document are designed to be used with ordinary electronic equipment or devices

(such as audio visual equipment, office-automation equipment, communications devices, electrical

appliances and electronic toys).

Should you intend to use these products with equipment or devices which require an extremely high level of

reliability and the malfunction of with would directly endanger human life (such as medical instruments,

transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other

safety devices), please be sure to consult with our sales representative in advance.

About Export Control Order in Japan

Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control

Order in Japan.

In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause)

on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction.

Appendix1-Rev1.1

ESR10EZPD82R5 [ROHM]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB

SI9137LG

SI9122E