MCR01ZZPF1023 [ROHM]

Fixed Resistor, Metal Glaze/thick Film, 0.063W, 102000ohm, 50V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0402, CHIP;


型号：	MCR01ZZPF1023
厂家：	ROHM
描述：	Fixed Resistor, Metal Glaze/thick Film, 0.063W, 102000ohm, 50V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0402, CHIP
文件：	总5页 (文件大小：74K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

MCR01

Resistors

Compact Thick Film Chip Resistors

MCR01 (1005 size : 1 / 16W)

zFeatures

1) Extremely small light

Area ratio is 60% smaller than that of chip 1608, while weight ratio has been cut 75%.

2) Highly reliable chip resistor

Ruthenium oxide dielectric offers superior resistance to the elements.

3) Electrodes not corroded by soldering

Thick film makes the electrodes very strong.

4) Flat surface further facilitates mounting

Mounting can also be automated.

5) ROHM resistors have approved ISO9001- / ISO/TS 16949- certification.

zRatings

Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with the

product before using or ordering it.

Item

Conditions

Specifications

0.063W (1 / 16W)

Power must be derated according to the power derating curve in

Figure 1 when ambient temperature exceeds 70°C.

Rated power

at 70°C

100

−55

100 125

155

AMBIENT TEMPERATURE (°C)

Fig.1

Rated voltage

The voltage rating is calculated by the following equation.

If the value obtained exceeds the limiting element voltage,

the voltage rating is equal to the maximum operating voltage.

E: Rated voltage (V)

P: Rated power (W)

R: Nominal resistance (Ω)

E= P×R

Limiting element voltage

50V

Nominal resistance

See Table 1.

−55°C to +155°C

Operating temperature

Rev.J

1/4

MCR01

Resistors

Table 1

Jumper type

Resistance

Max. 50mΩ

Resistance range

Resistance temperature coefficient

Resistance tolerance

(Ω)

(ppm / °C)

+500 / −250

200

Rated current

1.0 to 9.1

(E24)

Operating temperature

−55°C to +155°C

J ( 5%)

10 to 10M (E24)

F ( 1%)

D ( 0.5%)

10 to 2.2M (E24, E96)

100

10 to 91

(E24)

100 to 1M (E24)

zBefore using components in circuits where they will be exposed to transients such as pulse loads (short–duration, high– level loads), be certain to

evaluate the component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with

a steady state voltage that is greater than its rated voltage.

Characteristics

Guaranteed value

Resistor type Jumper type

J : 5%

Item

Resistance

Test conditions (JIS C 5201-1)

JIS C 5201-1 4.5

Max. 50mΩ

F : 1%

D : 0.5%

Variation of resistance

with temperature

JIS C 5201-1 4.8

Measurement : +25 / +125°C

See Table.1

JIS C 5201-1 4.13

Rated voltage (current) ×2.5, 2s.

Limiting Element Voltage×2 : 100V

Overload

(2.0%+0.1Ω)

Max. 50mΩ

A new uniform coating of minimum of

95% of the surface being immersed

and no soldering damage.

JIS C 5201-1 4.17

Rosin·Ethanol (25%WT)

Soldering condition : 235 5°C

Duration of immersion : 2.0 0.5s.

Solderability

(1.0%+0.05Ω)

No remarkable abnormality on the appearance.

Max. 50mΩ

JIS C 5201-1 4.18

Soldering condition : 260 5°C

Duration of immersion : 10 1s.

Resistance to

soldering heat

(1.0%+0.05Ω)

(3.0%+0.1Ω)

Max. 50mΩ

JIS C 5201-1 4.19

Test temp. : −55°C to +125°C 5cyc

Rapid change of

temperature

Max. 100mΩ

JIS C 5201-1 4.24

40°C, 93%RH

Test time : 1,000h to 1,048h

Damp heat, steady state

(3.0%+0.1Ω)

Max. 100mΩ

JIS C 5201-1 4.25.1

Rated voltage (current), 70°C

1.5h : ON − 0.5h : OFF

Test time : 1,000h to 1,048h

Endurance at 70°C

(3.0%+0.1Ω)

(1.0%+0.05Ω)

Max. 100mΩ

Max. 50mΩ

JIS C 5201-1 4.25.3

125°C

Endurance

Test time : 1,000h to 1,048h

JIS C 5201-1 4.29

23 5°C, Immersion cleaning, 5 0.5min.

Solvent : 2-propanol

Resistance to solvent

JIS C 5201-1 4.33

Bend strength of

the end face plating

Without mechanical damage such as breaks.

Rev.J

2/4

MCR01

Resistors

zDimensions (Unit : mm)

0.2 0.1

No.

Material

Resistive element (Oxide metal thick film)

Silver thick film electrode

Nickel electrode

+0.05

0.25

−0.1

1.0 0.05

Sn electrode

Alumina substrate

Overcoating (Resin)

Packaging

Reel

Taping

φD0

Heat crimp cover tape

(Underside paper tape)

Thick paper

mount

Chip resistor Square punchout hole

(Unit : mm)

8.0 0.3

3.5 0.05

1.75 0.1

0.7 0.1

1.2 0.1

Label

+0.1

EIAJ ET-7200B compliant

4.0 0.1

2.0 0.05

Max. 1.1

φ1.5

(Unit : mm)

Narrow pitch (1mm pitch) version

φD0

+1.0

φ180

φ13 0.2

φ60

−1.5

Bulk case

Heat crimp cover tape

(Underside paper tape)

Thick paper

mount

Slider

Square punchout hole

(Unit : mm)

Chip resistor

Shutter

12 0.1

−0.2

1.75 0.1

8.0 0.3

3.5 0.05

0.7 0.1

1.2 0.1

110 0.7

+0.1

EIAJ ET-7200B compliant

4.0 0.1

1.0 0.05

Max. 1.1

φ1.5

(Unit : mm)

Rev.J

3/4

MCR01

Resistors

zPart No. Explanation

M C R 0 1 M Z P

Part No.

Resistance tolerance Nominal resistance

0.5%

Resistance code, 3 or 4 digits.

000 denotes jumper type.

Resistance

tolerance

Resistance

code

J is also used

for jumper

F, D

4 digits

3 digits

Packaging Specifications Code

Resistance tolerance

Part No.

Code

Packaging specifications

Paper tape (2mm Pitch)

Reel

Basic ordering unit (pcs)

Remarks

(

)

(

)

(

)

0.5%

−

MCR01

MZP

ZZP

PZPI

φ180mm

−

10 000

−

Narrow pitch taping

Paper tape (1mm Pitch)

Bulkcase

20 000

50 000

−

Reel (φ180mm) : Compatible with JEITA standard "EIAJ ET-7200B"

: Standard product

Rev.J

4/4

Appendix

Notes

No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM

CO.,LTD.

The content specified herein is subject to change for improvement without notice.

The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you

wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM

upon request.

Examples of application circuits, circuit constants and any other information contained herein illustrate the

standard usage and operations of the Products. The peripheral conditions must be taken into account when

designing circuits for mass production.

Great care was taken in ensuring the accuracy of the information specified in this document. However, should

you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no respon-

sibility for such damage.

The technical information specified herein is intended only to show the typical functions of and examples of

application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or

exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility

whatsoever for any dispute arising from the use of such technical information.

The Products specified in this document are intended to be used with general-use electronic equipment or

devices (such as audio visual equipment, office-automation equipment, communication devices, electronic

appliances and amusement devices).

The Products are not designed to be radiation tolerant.

While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or

malfunction for a variety of reasons.

Please be sure to implement in your equipment using the Products safety measures to guard against the

possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as

derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your

use of any Product outside of the prescribed scope or not in accordance with the instruction manual.

The Products are not designed or manufactured to be used with any equipment, device or system

which requires an extremely high level of reliability the failure or malfunction of which may result in a direct

threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment,

aerospace machinery, nuclear-reactor controller, fuel-controller or other safety device). ROHM shall bear no

responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended

to be used for any such special purpose, please contact a ROHM sales representative before purchasing.

If you intend to export or ship overseas any Product or technology specified herein that may be controlled under

the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law.

Thank you for your accessing to ROHM product informations.

More detail product informations and catalogs are available, please contact your nearest sales office.

THE AMERICAS / EUROPE / ASIA / JAPAN

ROHM Customer Support System

www.rohm.com

TEL : +81-75-311-2121

FAX : +81-75-315-0172

21 Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan

Appendix1-Rev3.0

相关型号：