MCR100JZHF1211 [ROHM]

RES SMD 1.21K OHM 1% 1W 2512;


型号：	MCR100JZHF1211
厂家：	ROHM
描述：	RES SMD 1.21K OHM 1% 1W 2512
文件：	总9页 (文件大小：1022K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

General purpose chip resisitors

MCR series

Datasheet

●

Features

1)Full line up from ultra small size 01005 to 2512 with jumper type.

2)High reliability metal glazed thick film.

3)ROHM resistors have obtained ISO9001/IATF16949 certification.

4)Corresponds toAEC-Q200 (Except MCR004)

Automotive

Grade

Size

Packaging

Part No.

Type code

Quantity/ Reel

specifications

(mm)

0402

0603

1005

1608

2012

3216

3225

5025

6432

(inch)

01005

0201

0402

0603

0805

1206

1210

2010

2512

Available

MCR004

MCR006

MCR01

QLP

YLP

MZP

EZP

JZH

Paper tape(2mmPitch)

Paper tape(4mmPitch)

Embossed tape(4mmPitch)

20,000

15,000

10,000

5,000

4,000

－

Yes

MCR03

MCR10

MCR18

▲MCR25

▲MCR50

▲MCR100

*▲：NRND(Not Recommended for New Design)

●

Part number description

M C R

0 0 4

Q L P

1 0 0

Part No.

Size (mm [inch])

Type code

Resistance tolerance

Nominal resistance

Resistance code, 3 or 4 digits.

000 denotes jumper type.

004(0402 [01005])

006(0603 [0201])

01(1005 [0402])

03(1608 [0603])

10(2012 [0805])

18(3216 [1206])

25(3225 [1210])

50(5025 [2010])

100(6432 [2512])

D(±0.5%)

F(±1%)

FX(±1%) *Only MCR03EZP

J(±5%) (Including jumper type)

MCR

(General purpose

chip resistors)

Resistance

tolerance

Resistance

code

：

D,F

4 digits

3 digits

：

EX.)

1Ω=1R0 (±5%)

9.1Ω=9R1 (±5%)

10Ω=10R0 (±0.5%,±1%)

100 (±5%)

2.2MΩ=2204 (±0.5%,± 1%)

225 (±5%)

www.rohm.com

1/6

2020.07 - Rev.Q

MCR series

●Productslist

Part No.

Datasheet

Rated power Limiting element Temperature Resistance

Operating

temperature range

(℃)

Resistancerange

(Ω)

Type code

QLP

(70℃)

voltage

(V)

coefficient

(ppm/ ℃)

±300

±250

+600/-100

±300

tolerance

(%)

(W)

F ( ±1%)

J ( ±5%)

(E24/96 series)

10≦Ｒ＜100

100≦Ｒ≦1M

1.0≦Ｒ＜10

10≦Ｒ＜100

100≦Ｒ≦1M

(E24/96 series)

(E24 series)

0.031

0.05

0.063

0.1

MCR004

MCR006

MCR01

MCR03

MCR10

-55～ +125

-55～ +155

±250

Jumper type ) Rmax ： 50mΩMax., Imax ： 0.5A

D ( ±0.5%)

F ( ±1%)

J ( ±5%)

(E24/96 series)

(E24 series)

±200

±100

±200

+600 / -200

±200

10≦Ｒ＜1k

1k≦Ｒ≦1M

10≦Ｒ≦10M

1.0≦Ｒ＜10

10≦Ｒ≦10M

YLP

MZP

EZP

J ( ±5%)

(E24 series)

Jumper type ) Rmax ： 50mΩMax., Imax ： 0.5A

D ( ±0.5%)

F ( ±1%)

J ( ±5%)

(E24/96 series)

(E24 series)

±100

±50

±100

+500/-250

±200

10≦R＜100

100≦R≦1M

10≦R≦2.2M

1.0≦R＜10

10≦R≦10M

J ( ±5%)

(E24 series)

Jumper type ) Rmax ： 50mΩMax., Imax ： 1A

D ( ±0.5%)

FX( ±1%)

J ( ±5%)

(E24/96 series)

(E24 series)

±100

±50

±100

±400

±200

10≦R<100

100≦R≦1M

10≦R≦10M

1.0≦R<10

J ( ±5%)

(E24 series)

10≦R≦10M

Jumper type ) Rmax ： 50mΩMax., Imax ： 1A

D ( ±0.5%)

F ( ±1%)

J ( ±5%)

(E24/96 series)

(E24 series)

±100

±50

±100

±400

±200

10≦R<100

100≦R≦1M

10≦R≦2.2M

1.0≦R<10

0.1

150

-55～ +155

0.125

J ( ±5%)

(E24 series)

10≦R≦10M

Jumper type ) Rmax ： 50mΩMax., Imax ： 2A

D ( ±0.5%)

F ( ±1%)

J ( ±5%)

(E24/96 series)

(E24 series)

±100

±50

±100

±400

±200

10≦R<100

100≦R≦1M

10≦R≦2.2M

1.0≦R<10

0.125

0.25

200

MCR18

▲MCR25

▲MCR50

EZP

JZH

J ( ±5%)

(E24 series)

10≦R≦10M

Jumper type ) Rmax ： 50mΩMax., Imax ： 2A

F ( ±1%)

J ( ±5%)

(E24/96 series)

(E24 series)

±100

500±350

±500

10≦R≦1M

1.0≦R<2.2

2.2≦R<5.6

5.6≦R≦3.3M

200

0.25to0.5

0.5

-55～ +155

±200

Jumper type ) Rmax ： 50mΩMax., Imax ： 2A

F ( ±1%)

J ( ±5%)

(E24/96 series)

(E24 series)

±100

500±350

±500

±200

±350

10 ≦ R ≦ 180k

1.0 ≦ R <2.2

2.2 ≦ R <10

10 ≦ R ≦ 330k

330k <R ≦ 560k

Jumper type ) Rmax ： 50mΩMax., Imax ： 3A

F ( ±1%)

J ( ±5%)

(E24/96 series)

(E24 series)

±100

500±350

±500

±350

±200

10≦R≦82k

1.0≦R<2.2

2.2≦R<10

10≦R<24

200

▲MCR100

JZH

-55～ +125

24≦R≦100k

Jumper type ) Rmax ： 50mΩMax., Imax ： 4A

Design and specifications are subject to change without notice.Carefully check the specification sheet supplied

with the product before using or ordering it.

Rated voltage is determained from the following.

When rated voltage exceeds the limiting element voltage, the limitng element voltage shall be the rated voltage.

Rated voltage =

* E24 : Standard products,

E96 : Custom products

*1. Rated powerꢀ1Ω～9.76Ω ： 0.25W,ꢀ10Ω～9.76kΩ ： 0.5W,ꢀ10kΩ～3.3MΩ ： 0.33W

www.rohm.com

2/6

2020.07 - Rev.Q

MCR series

●Chip resistor dimensions and markings

■MCR004 / 006 / 01 / 03

Datasheet

■MCR10 / 18 / 25 / 50 / 100

There are three or four digits used for the calculation

number according to IEC code and R is used for the

decimal point.

(Unit:mm)

Marking

Part No.

Type code

QLP

(mm)

(inch)

existence

MCR004

0402

01005

0.40±0.02

0.20±0.02

0.13±0.02

0.10±0.03

MCR006

MCR01

YLP

MZP

EZP

JZH

0603

1005

1608

2012

3216

3225

5025

6432

0201

0402

0603

0805

1206

1210

2010

2512

0.60±0.03

1.00±0.05

1.60±0.10

2.00±0.10

3.20±0.15

5.00±0.15

6.30±0.15

0.30±0.03

0.50±0.05

0.80±0.10

1.25±0.10

1.60±0.15

2.50±0.15

3.20±0.15

0.23±0.03

0.35±0.05

0.45±0.10

0.55±0.10

0.55±0.15

0.10±0.05

0.20±0.10

0.30±0.20

0.40±0.20

0.50±0.25

0.60±0.25

0.15±0.05

+0.05

0.25

-0.10

MCR03

0.30±0.20

0.40±0.20

0.50±0.25

0.60±0.25

Yes*

Yes

MCR10

MCR18

▲MCR25

▲MCR50

▲MCR100

Marking method of jumper type

Jumper type

Marking existence

MCR004 / 006 / 01 / 25 / 50 / 100

MCR03 / 10 / 18

Yes

*Marking method of MCR25/50/100

Blueglass over coat is used for the jumper type.There is no marking on the jumper type.

*Marking method of MCR03

For MCR03 series resistors, the printingprocess restricts the marking to three digits/characters. Consequently, 1%tolerance resistors

with values fromthe E24 series will be markedthe same as 5%resistors with the same value, but 1%tolerance resistors

with values fromthe E96 series will not bemarked. However, regarding E96 series, the resistance values which overlaps

with E24 series will be indicated by 3 digits.

Examples:

MCR03EZPJ243

(5%tolerance, E24 / 24 kΩ)

(1%tolerance, E24 / 24 kΩ)

(1%tolerance, E96 / 24.3 kΩ)

(1%tolerance, E24,E96 / 200Ω)

Marking =243

No Marking

MCR03EZPFX2402

MCR03EZPFX2432

MCR03EZPFX2000

Marking =201

MCR18EZPJ243

MCR18EZPF2402

MCR18EZPF2432

(5%tolerance, E24 / 24 kΩ)

(1%tolerance, E24 / 24 kΩ)

(1%tolerance, E96 / 24.3 kΩ)

Marking =243

Marking =2402

Marking =2432

www.rohm.com

3/6

2020.07 - Rev.Q

MCR series

Datasheet

●Land pattern example

(Unit:mm)

Dimensions

Part No.

MCR004

MCR006

MCR01

MCR03

MCR10

MCR18

MCR25

MCR50

MCR100

0.12

0.3

0.5

1.0

1.2

2.2

3.8

5.1

0.48

0.84

1.3

2.0

2.6

4.0

6.0

8.1

0.22

0.3

0.5

0.8

1.15

1.5

2.3

3.0

0.18

0.27

0.4

0.5

0.7

0.9

1.1

1.5

●Derating curve

When the ambient temperature exceeds 70°C, power dissipation must be adjusted according to the derating curve below.

■MCR004 / 006 / 100

■MCR01 / 03 / 10 / 18 / 25 / 50

●Characteristics

Test items

Guaranteed value

Resistor type Jumper type

See "Products list"

Test conditions

Resistance

20℃

Variationof resistance

with temperature

See "Products list"

Measurement：+25/-55, +25/+125℃

Test voltage is the smaller one of ① or ②

①Rated voltage(current)×2.5， 2s

②Maximumoverload voltage※

Overload

±(2.0％＋0.1Ω) MAX. 50mΩ

Anew uniformcoating of minimumof

95%of the surface being immersed and

no soldering damage.

Rosin-ethanol solution(25%mass)

Soldering condition：245±5℃

Duration of immersion：2.0±0.5s

Solderability

Resistanceto

soldering heat

±(1.0％＋0.05Ω)

No remarkable abnormality on the appearance.

MAX. 50mΩ

Soldering condition：260±5℃

Duration of immersion：10±1s

±(1.0％＋0.05Ω)

MAX. 50mΩ

Test temp.

-55℃～+125℃ 1,000cycles(MCR01)

-55℃～+125℃ 100cycles(MCR004/006)

-55℃～+125℃ 5cycles(MCR03/10/18/25/50/100)

Rapidchange of

temperature

±(3.0％＋0.1Ω)

MAX. 100mΩ

40℃，93％(Relative humidity)

Test time：1,000h

Rated voltage(current),70℃±3℃

1.5h:ON－0.5h:OFF

Dampheat, steady state

Enduranceat 70℃

Test time：1,000h

±(3.0％＋0.1Ω)

MAX. 100mΩ

155℃(MCR01/03/10/18/25/50)

125℃(MCR004/006/100)

Test time：1,000h

Endurance

±(1.0％＋0.05Ω)

MAX. 50mΩ

23±5℃, Immersion cleaning, 5±0.5min

Resistanceto solvent

Solvent: 2-propanol

Bend strength of

the end face plating

Without mechanical damage such as breaks.

※Maximum overload voltage (Test voltage)

Compliance Standard(s) : IEC60115-8

JISC 5201-8

MCR004 MCR006 MCR01 MCR03 MCR10 MCR18 MCR25 MCR50 MCR100

30V

50V

100V

300V 400V 400V 400V 400V

www.rohm.com

4/6

2020.07 - Rev.Q

MCR series

Datasheet

(Unit : mm)

●Tape dimensions

■Paper tape

Type code

QLP

Part No.

MCR004

8.0±0.2

3.5±0.05 1.75±0.1 0.24±0.03 0.45±0.03

3.5±0.05 1.75±0.1 0.38±0.03 0.68±0.03

MCR006

MCR01

MCR03

MCR10

MCR18

YLP

MZP

EZP

8.0±0.2

8.0±0.3

3.5±0.05 1.75±0.1

0.7±0.1

1.2±0.1

1.9±0.1

1.1±0.1

+0.2

2.4

3.5±0.05 1.75±0.1 1.65

3.5±0.05 1.75±0.1 1.95

-0.1

+0.1

-0.05

+0.15

3.5

-0.05

Part No.

Type code

QLP

+0.1

MCR004

Φ1.5

4.0±0.1

2.0±0.05 2.0±0.05 MAX0.5

2.0±0.05 2.0±0.05 MAX1.1

+0.1

MCR006

MCR01

MCR03

MCR10

MCR18

YLP

MZP

EZP

Φ1.5

4.0±0.1

+0.1

4.0±0.1

2.0±0.05 MAX1.1

+0.1

MAX

1.1

2.0±0.05

(Unit : mm)

■Embossed tape

Part No.

Type code

JZH

MCR25

8.0±0.3

12.0±0.3

3.5±0.05 1.75±0.1

5.5±0.05 1.75±0.1

3.0±0.1

3.4±0.2

3.5±0.2

3.5±0.1

5.6±0.2

6.7±0.2

MCR50

JZH

MCR100

Part No.

Type code

JZH

+0.1

Φ1.5

MCR25

4.0±0.1

2.0±0.05 MAX1.1

+0.1

Φ1.5

MCR50

JZH

4.0±0.1

+0.1

Φ1.5

MAX

2.0±0.05 1.1

MCR100

www.rohm.com

5/6

2020.07 - Rev.Q

MCR series

Datasheet

●Reel dimensions

Using two kinds of reels for taping.

①MCR 004/006/01/03/10/18/25/50/100

②MCR 004/006/01/03/10/18/25

(Unit : mm)

Part No.

MCR004

MCR006

MCR01

MCR03

MCR10

MCR18

MCR25

MCR50

MCR100

Typecode

QLP

YLP

MZP

EZP

+1.0

-1.5

+1.0

EZP

JZH

Φ180

Φ60

Φ13±0.2

+1.0

JZH

www.rohm.com

6/6

2020.07 - Rev.Q

Notice

Precaution on using ROHM Products

(Note 1)

1. If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment

aircraft/spacecraft, nuclear power controllers, etc.) and whose malfunction or failure may cause loss of human life,

bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales

representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way

responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any

ROHM’s Products for Specific Applications.

(Note1) Medical Equipment Classification of the Specific Applications

JAPAN

USA

CHINA

CLASSⅢ

CLASSⅣ

CLASSⅡb

CLASSⅢ

2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor

products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate

safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which

a failure or malfunction of our Products may cause. The following are examples of safety measures:

[a] Installation of protection circuits or other protective devices to improve system safety

[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure

3. Our Products are not designed under any special or extraordinary environments or conditions, as exemplified below.

Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the

use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our

Products under any special or extraordinary environments or conditions (as exemplified below), your independent

verification and confirmation of product performance, reliability, etc, prior to use, must be necessary:

[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents

[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust

[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,

H2S, NH3, SO2, and NO2

[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves

[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items

[f] Sealing or coating our Products with resin or other coating materials

[g] Use of our Products without cleaning residue of flux (Exclude cases where no-clean type fluxes is used.

However, recommend sufficiently about the residue.); or Washing our Products by using water or water-soluble

cleaning agents for cleaning residue after soldering

[h] Use of the Products in places subject to dew condensation

4. The Products are not subject to radiation-proof design.

5. Please verify and confirm characteristics of the final or mounted products in using the Products.

6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse, is applied,

confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power

exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect

product performance and reliability.

7. De-rate Power Dissipation depending on ambient temperature. When used in sealed area, confirm that it is the use in

the range that does not exceed the maximum junction temperature.

8. Confirm that operation temperature is within the specified range described in the product specification.

9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in

this document.

Precaution for Mounting / Circuit board design

1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product

performance and reliability.

2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must

be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products,

please consult with the ROHM representative in advance.

For details, please refer to ROHM Mounting specification

Notice-PAA-E

Rev.004

Precautions Regarding Application Examples and External Circuits

1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the

characteristics of the Products and external components, including transient characteristics, as well as static

characteristics.

2. You agree that application notes, reference designs, and associated data and information contained in this document

are presented only as guidance for Products use. Therefore, in case you use such information, you are solely

responsible for it and you must exercise your own independent verification and judgment in the use of such information

contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses

incurred by you or third parties arising from the use of such information.

Precaution for Electrostatic

This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper

caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be

applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,

isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).

Precaution for Storage / Transportation

1. Product performance and soldered connections may deteriorate if the Products are stored in the places where:

[a] the Products are exposed to sea winds or corrosive gases, including Cl₂, H₂S, NH₃, SO₂, and NO₂

[b] the temperature or humidity exceeds those recommended by ROHM

[c] the Products are exposed to direct sunshine or condensation

[d] the Products are exposed to high Electrostatic

2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period

may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is

exceeding the recommended storage time period.

3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads

may occur due to excessive stress applied when dropping of a carton.

4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of

which storage time is exceeding the recommended storage time period.

Precaution for Product Label

A two-dimensional barcode printed on ROHM Products label is for ROHM’s internal use only.

Precaution for Disposition

When disposing Products please dispose them properly using an authorized industry waste company.

Precaution for Foreign Exchange and Foreign Trade act

Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign

trade act, please consult with ROHM in case of export.

Precaution Regarding Intellectual Property Rights

1. All information and data including but not limited to application example contained in this document is for reference

only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any

other rights of any third party regarding such information or data.

2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the

Products with other articles such as components, circuits, systems or external equipment (including software).

3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any

third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM

will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to

manufacture or sell products containing the Products, subject to the terms and conditions herein.

Other Precaution

1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.

2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written

consent of ROHM.

3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the

Products or this document for any military purposes, including but not limited to, the development of mass-destruction

weapons.

4. The proper names of companies or products described in this document are trademarks or registered trademarks of

ROHM, its affiliated companies or third parties.

Notice-PAA-E

Rev.004

Daattaasshheeeett

General Precaution

1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents.

ROHM shall not be in an y way responsible or liable for failure, malfunction or accident arising from the use of a ny

ROHM’s Products against warning, caution or note contained in this document.

2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior

notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s

representative.

3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all

information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or

liable for any damages, expenses or losses incurred by you or third parties resulting from inaccuracy or errors of or

concerning such information.

Notice – WE

Rev.001

MCR100JZHF1211 [ROHM]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB

SI9137LG

SI9122E