MNR02M0APJ331 [ROHM]
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 330ohm, 25V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0404, CHIP;型号: | MNR02M0APJ331 |
厂家: | ROHM |
描述: | Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 330ohm, 25V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0404, CHIP 电阻器 |
文件: | 总5页 (文件大小:77K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MNR02
Resistors
Compact Chip Resistor Networks
MNR02 (1005 × 2 size)
zFeatures
1) Extremely small and light
Area ratio is 60% smaller than that of chip 1616 (MNR12), while weight ratio has been cut 75%.
2) High-density mounting
Can be mounted even more densely than two 1005 chips (MCR01). Also, the cost of mounting has been reduced.
3) Compatible with a wide range of mounting equipment.
Squared corners make it excellent for mounting using image recognition devices.
4) Convex electrodes
Easy to check the fillet after soldering is finished.
5) ROHM resistors have obtained ISO9001- / ISO/TS 16949- certification.
zRatings
Design and specifications are subject to change without notice. Carefully check the specification sheet before using or
ordering it.
Item
Conditions
Specifications
0.063W (1 / 16W)
Rated power
Power must be derated according to the power derating curve in
Figure 1 when ambient temperature exceeds 70°C.
at 70°C
100
80
60
40
20
0
−55
0
70
100 125
155
AMBIENT TEMPERATURE (°C)
Fig.1
Rated voltage
The voltage rating is calculated by the following equation.
If the value obtained exceeds the limiting element voltage,
the voltage rating is equal to the maximum operating voltage.
E: Rated voltage (V)
P: Rated power (W)
E = P×R
Limiting element voltage
25V
R: Nominal resistance (Ω)
Nominal resistance See Table 1.
Operating temperature
−55°C to +125°C
Rev.E
1/4
MNR02
Resistors
Jumper type
Resistance
Max. 50mΩ
1A
Rated current
Operating temperature
−55°C to +125°C
Table 1
Resistance range
Resistance temperature coefficient
Resistance tolerance
J ( 5%)
(Ω)
(ppm / °C)
10 to 1M (E24)
300
•Before using components in circuits where they will be exposed to transients such as pulse loads (short-duration, high-level loads), be certain to evaluate the
component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that
is greater than its rated voltage.
zCharacteristics
Guaranteed value
Items
Resistance
Test conditions (JIS C 5201-1)
JIS C 5201-1 4.5
Resistor type
J : 5%
Variation of resistance
with temperature
JIS C 5201-1 4.8
Measurement : −55 / +25 / +125°C
See Table.1
JIS C 5201-1 4.13
Rated voltage (current) ×2.5, 2s.
Limiting Element Voltage×2 : 50V
Overload
(2.0%+0.1Ω)
A new uniform coating of minimum of
95% of the surface being immersed
and no soldering damage.
JIS C 5201-1 4.17
Rosin·Ethanol (25%WT)
Soldering condition : 235 5°C
Duration of immersion : 2.0 0.5s.
Solderability
(1.0%+0.05Ω)
No remarkable abnormality on the appearance.
JIS C 5201-1 4.18
Soldering condition : 260 5°C
Duration of immersion : 10 1s.
Resistance to
soldering heat
(1.0%+0.05Ω)
(3.0%+0.1Ω)
JIS C 5201-1 4.19
Test temp. : −55°C to +125°C 5cyc
Rapid change of
temperature
JIS C 5201-1 4.24
40°C, 93%RH
Test time : 1,000h to 1,048h
Damp heat, steady state
(3.0%+0.1Ω)
JIS C 5201-1 4.25.1
Rated voltage (current), 70°C
1.5h : ON − 0.5h : OFF
Test time : 1,000h to 1,048h
Endurance at 70°C
(3.0%+0.1Ω)
(1.0%+0.05Ω)
JIS C 5201-1 4.25.3
125°C
Endurance
Test time : 1,000h to 1,048h
JIS C 5201-1 4.29
23 5°C, Immersion cleaning, 5 0.5min.
Solvent : 2-propanol
Resistance to solvent
(1.0%+0.05Ω)
Without mechanical damage such as breaks.
JIS C 5201-1 4.33
Bend strength of
the end face plating
Rev.E
2/4
MNR02
Resistors
zDimensions (Unit: mm)
1.0 0.1
B
6
1
Cross section A-A'
Cross section B-B'
No.
1
Material
5
Resistive element (Oxide metal thick film)
Silver thick film electrode
Nickel electrode
2
6
1
A
A'
3
4
Sn electrode
5
2
5
Alumina substrate
3
4
B'
6
Overcoating (Resin)
0.35 0.1
+0.1
+0.05
−0.1
0.33
0.34
−0.05
0.68
zEquivalent circuit
R1
R2
R1 = R2
Rev.E
3/4
MNR02
Resistors
zPackaging
Reel
Taping
P
0
P
2
φ
D
0
E
F
A
0
W
A
B
D
P
1
Heat crimp cover / Tape
Chip network
resistors
Thick paper (Underside paper tape)
mount
Square punchout hole
T
2
C
Label
(Unit: mm)
EIAJ ET-7200B compliant
W
F
E
A
0
B0
(Unit: mm)
D
8.0 0.3
3.5 0.05
1.75 0.1
1.17 0.1
1.17 0.1
A
B
C
D
0
P
0
P
1
P
2
T2
0
−1.5
+1
0
+1.0
0
φ180
φ60
9
φ13 0.2
+0.1
4.0 0.1
2.0 0.1
2.0 0.05
Max. 0.5
φ1.5
0
zPart No. Explanation
P
Part No.
Resistance tolerance
Nominal resistance
J
5%
Resistance code, 3 or 4 digits.
000 denotes jumper type.
J is also used
for jumper.
Resistance
tolerance
Resistance
code
Packaging Specifications Code
:
3digits
J
Resistance tolerance
J( 5%)
Part No. Code
MNR02 M0AP
Packaging specifications
Reel
Basic ordering unit (pcs)
Paper tape (2mmPitch)
φ180mm
10,000
Reel (φ180mm) : Compatible with JEITA standard "EIAJ ET-7200B"
: Standard product
Rev.E
4/4
Appendix
Notes
No technical content pages of this document may be reproduced in any form or transmitted by any
means without prior permission of ROHM CO.,LTD.
The contents described herein are subject to change without notice. The specifications for the
product described in this document are for reference only. Upon actual use, therefore, please request
that specifications to be separately delivered.
Application circuit diagrams and circuit constants contained herein are shown as examples of standard
use and operation. Please pay careful attention to the peripheral conditions when designing circuits
and deciding upon circuit constants in the set.
Any data, including, but not limited to application circuit diagrams information, described herein
are intended only as illustrations of such devices and not as the specifications for such devices. ROHM
CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any
third party's intellectual property rights or other proprietary rights, and further, assumes no liability of
whatsoever nature in the event of any such infringement, or arising from or connected with or related
to the use of such devices.
Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or
otherwise dispose of the same, no express or implied right or license to practice or commercially
exploit any intellectual property rights or other proprietary rights owned or controlled by
ROHM CO., LTD. is granted to any such buyer.
Products listed in this document are no antiradiation design.
The products listed in this document are designed to be used with ordinary electronic equipment or devices
(such as audio visual equipment, office-automation equipment, communications devices, electrical
appliances and electronic toys).
Should you intend to use these products with equipment or devices which require an extremely high level
of reliability and the malfunction of which would directly endanger human life (such as medical
instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers
and other safety devices), please be sure to consult with our sales representative in advance.
It is our top priority to supply products with the utmost quality and reliability. However, there is always a chance
of failure due to unexpected factors. Therefore, please take into account the derating characteristics and allow
for sufficient safety features, such as extra margin, anti-flammability, and fail-safe measures when designing in
order to prevent possible accidents that may result in bodily harm or fire caused by component failure. ROHM
cannot be held responsible for any damages arising from the use of the products under conditions out of the
range of the specifications or due to non-compliance with the NOTES specified in this catalog.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact your nearest sales office.
THE AMERICAS / EUROPE / ASIA / JAPAN
ROHM Customer Support System
Contact us : webmaster@ rohm.co.jp
www.rohm.com
TEL : +81-75-311-2121
FAX : +81-75-315-0172
Copyright © 2008 ROHM CO.,LTD.
21 Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan
Appendix1-Rev2.0
相关型号:
MNR02M0APJ332
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 3300ohm, 25V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0404, CHIP
ROHM
MNR02M0APJ334
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 330000ohm, 25V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0404, CHIP
ROHM
MNR02M0APJ360
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 36ohm, 25V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0404, CHIP
ROHM
MNR02M0APJ361
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 360ohm, 25V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0404, CHIP
ROHM
MNR02M0APJ363
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 36000ohm, 25V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0404, CHIP
ROHM
MNR02M0APJ364
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 360000ohm, 25V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0404, CHIP
ROHM
MNR02M0APJ472
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 4700ohm, 25V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0404, CHIP
ROHM
MNR02M0APJ560
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 56ohm, 25V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0404, CHIP
ROHM
MNR02M0APJ562
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 5600ohm, 25V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0404, CHIP
ROHM
MNR02M0APJ624
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 620000ohm, 25V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0404, CHIP
ROHM
MNR02M0APJ682
Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 6800ohm, 25V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0404, CHIP
ROHM
©2020 ICPDF网 联系我们和版权申明