MNR04M0ABJ622 [ROHM]

RESISTOR, NETWORK, FILM, ISOLATED, SURFACE MOUNT, 0408, CHIP;


型号：	MNR04M0ABJ622
厂家：	ROHM
描述：	RESISTOR, NETWORK, FILM, ISOLATED, SURFACE MOUNT, 0408, CHIP
文件：	总4页 (文件大小：80K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

MNR04

Resistors

Chip resistor networks

MNR04 (1005 × 4 size)

!Features

1) Extremely small and light

Area ratio is 60% smaller than that of chip 3216 (MNR14), while weight ratio has been cut 75%.

2) High-density mounting

Can be mounted even more densely than four 1005 chips (MCR01), and mounting costs are lower.

3) Can be mounted on a wide variety of devices

Squared corners make it excellent for mounting on image recognition devices.

4) Convex electrodes

Easy to check the fillet after soldering is finished.

5) ROHM resistors comply with the international standard ISO-9001.

Furthermore, changes to the design and specifications of products may occur without notice. Therefore, before

ordering or using this product, please make sure to reconfirm the specification sheet before ordering or using this

product.

!Ratings

Item

Conditions

Specifications

0.063W (1 / 16W)

Rated power

Power must be derated according to the power derating curve in

at 70°C

Figure 1 when ambient temperature exceeds 70°C.

100

Ð 55

100 125

AMBIENT TEMPERATURE (°C)

Fig.1

Rated voltage

The voltage rating is calculated by the following equation. If the

value obtained exceeds the limiting element voltage, the voltage

rating is equal to maximum operating voltage.

E : Voltage rating (V)

E = P×R

P : Power rating (W)

R : Nominal resistance (Ω)

Limiting element voltage 25V

Nominal resistance

See Table 1.

Operating temperature

−55°C~+125°C

1/4

MNR04

Resistors

Jumper type

Table 1

Resistance range

Resistance temperature

coefficient (ppm / °C)

Resistance

Max.50mΩ

Resistance tolerance

J ( 5%)

(Ω)

Rated current

10≤R≤1M

(E24)

300

Operating temperature −55°C~+125°C

•Before using components in circuits where they will be exposed to transients such as pulse loads (short-duration, high-level loads), be certain to evaluate the

component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that

is greater than its rated voltage.

!Characteristics

Guaranteed value

Item

Test conditions (JIS C 5201-1)

JIS C 5201-1 4.5

Resistor type

J : 5%

Jumper type

Max. 50mΩ

Resistance

Variation of resistance

with temperature

JIS C 5201-1 4.8

Measurement : −55 / +25 / +125°C

See Table.1

JIS C 5201-1 4.13

Rated voltage (current) ×2.5, 2s.

Limiting Element Voltage×2 : 50V

Overload

(2.0%+0.1Ω)

Max. 50mΩ

A new uniform coating of minimum of

95% of the surface being immersed

and no soldering damage.

JIS C 5201-1 4.17

Rosin·Ethanol (25%WT)

Soldering condition : 235 5°C

Duration of immersion : 2.0 0.5s.

Solderability

(1.0%+0.05Ω)

No remarkable abnormality on the appearance.

Max. 50mΩ

JIS C 5201-1 4.18

Soldering condition : 260 5°C

Duration of immersion : 10 1s.

Resistance to

soldering heat

(1.0%+0.05Ω)

(3.0%+0.1Ω)

Max. 50mΩ

JIS C 5201-1 4.19

Test temp. : −55°C~+125°C 5cyc

Rapid change of

temperature

JIS C 5201-1 4.24

40°C, 93%RH

Test time : 1,000h~1,048h

Damp heat, steady state

(3.0%+0.1Ω)

Max. 50mΩ

JIS C 5201-1 4.25.1

Rated voltage (current), 70°C

1.5h : ON − 0.5h : OFF

Test time : 1,000h~1,048h

Endurance at 70°C

(3.0%+0.1Ω)

(1.0%+0.05Ω)

Max. 50mΩ

JIS C 5201-1 4.25.3

125°C

Endurance

Test time : 1,000h~1,048h

JIS C 5201-1 4.29

23 5°C, Immersion cleaning, 5 0.5min.

Solvent : 2-propanol

Resistance to solvent

JIS C 5201-1 4.33

Bend strength of

the end face plating

Without mechanical damage such as breaks.

2/4

MNR04

Resistors

!External dimensions (Units: mm)

2.0 0.2

a : 0.4 0.15

b : 0.3 0.15

No.

Material

Thick dielectric glaze of Ruthenium

Thick film of silver for primary electrode

Nickel-coated secondary electrode

External electrode coated with Sn/Pb or Sn

Alumina substrate

∗

0.5

Overcoating

Cross section A - A'

Cross section B - B'

∗ The pitch between electrodes.

!Equivalent circuit

R1 = R2 = R3 = R4

3/4

MNR04

Resistors

!Packaging

Reel

Taping

φD

Heat crimp cover / Tape

Thick paper mount

Chip network resistors

(Underside paper tape) Square punchout hole

Label

(Units : mm)

EIAJ ET-7200A compliant

(Units : mm)

8.0 0.3

3.5 0.05

1.75 0.1

1.2 0.1

2.2 0.1

−3

+1.0

φ180

φ60

φ13 0.2

+0.1

4.0 0.1

2.0 0.1

2.0 0.05

Max. 0.5

φ1.5

!Product designation

Part no.

Packaging / Processing specifications

Circuit configuration Resistance Nominal resistance

code

tolerance

Packaging

Taping

Package style

Paper tape with reel (10,000)

Code Part no.

M0 MNR02 / 04

3-digit IEC coding system

AB MNR04 / 12 / 14 / 32 / 34

4/4

相关型号：