MNR04M0ABJ750 [ROHM]
RESISTOR, NETWORK, FILM, ISOLATED, SURFACE MOUNT, 0408, CHIP;型号: | MNR04M0ABJ750 |
厂家: | ROHM |
描述: | RESISTOR, NETWORK, FILM, ISOLATED, SURFACE MOUNT, 0408, CHIP 电阻器 |
文件: | 总4页 (文件大小:80K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MNR04
Resistors
Chip resistor networks
MNR04 (1005 × 4 size)
!Features
1) Extremely small and light
Area ratio is 60% smaller than that of chip 3216 (MNR14), while weight ratio has been cut 75%.
2) High-density mounting
Can be mounted even more densely than four 1005 chips (MCR01), and mounting costs are lower.
3) Can be mounted on a wide variety of devices
Squared corners make it excellent for mounting on image recognition devices.
4) Convex electrodes
Easy to check the fillet after soldering is finished.
5) ROHM resistors comply with the international standard ISO-9001.
Furthermore, changes to the design and specifications of products may occur without notice. Therefore, before
ordering or using this product, please make sure to reconfirm the specification sheet before ordering or using this
product.
!Ratings
Item
Conditions
Specifications
0.063W (1 / 16W)
Rated power
Power must be derated according to the power derating curve in
at 70°C
Figure 1 when ambient temperature exceeds 70°C.
100
80
60
40
20
0
Ð 55
0
70
100 125
AMBIENT TEMPERATURE (°C)
Fig.1
Rated voltage
The voltage rating is calculated by the following equation. If the
value obtained exceeds the limiting element voltage, the voltage
rating is equal to maximum operating voltage.
E : Voltage rating (V)
E = P×R
P : Power rating (W)
R : Nominal resistance (Ω)
Limiting element voltage 25V
Nominal resistance
See Table 1.
Operating temperature
−55°C~+125°C
1/4
MNR04
Resistors
Jumper type
Table 1
Resistance range
Resistance temperature
coefficient (ppm / °C)
Resistance
Max.50mΩ
Resistance tolerance
J ( 5%)
(Ω)
Rated current
1A
10≤R≤1M
(E24)
300
Operating temperature −55°C~+125°C
•Before using components in circuits where they will be exposed to transients such as pulse loads (short-duration, high-level loads), be certain to evaluate the
component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that
is greater than its rated voltage.
!Characteristics
Guaranteed value
Item
Test conditions (JIS C 5201-1)
JIS C 5201-1 4.5
Resistor type
J : 5%
Jumper type
Max. 50mΩ
Resistance
Variation of resistance
with temperature
JIS C 5201-1 4.8
Measurement : −55 / +25 / +125°C
See Table.1
JIS C 5201-1 4.13
Rated voltage (current) ×2.5, 2s.
Limiting Element Voltage×2 : 50V
Overload
(2.0%+0.1Ω)
Max. 50mΩ
A new uniform coating of minimum of
95% of the surface being immersed
and no soldering damage.
JIS C 5201-1 4.17
Rosin·Ethanol (25%WT)
Soldering condition : 235 5°C
Duration of immersion : 2.0 0.5s.
Solderability
(1.0%+0.05Ω)
No remarkable abnormality on the appearance.
Max. 50mΩ
JIS C 5201-1 4.18
Soldering condition : 260 5°C
Duration of immersion : 10 1s.
Resistance to
soldering heat
(1.0%+0.05Ω)
(3.0%+0.1Ω)
Max. 50mΩ
Max. 50mΩ
JIS C 5201-1 4.19
Test temp. : −55°C~+125°C 5cyc
Rapid change of
temperature
JIS C 5201-1 4.24
40°C, 93%RH
Test time : 1,000h~1,048h
Damp heat, steady state
(3.0%+0.1Ω)
Max. 50mΩ
JIS C 5201-1 4.25.1
Rated voltage (current), 70°C
1.5h : ON − 0.5h : OFF
Test time : 1,000h~1,048h
Endurance at 70°C
(3.0%+0.1Ω)
(1.0%+0.05Ω)
(1.0%+0.05Ω)
Max. 50mΩ
Max. 50mΩ
Max. 50mΩ
JIS C 5201-1 4.25.3
125°C
Endurance
Test time : 1,000h~1,048h
JIS C 5201-1 4.29
23 5°C, Immersion cleaning, 5 0.5min.
Solvent : 2-propanol
Resistance to solvent
JIS C 5201-1 4.33
Bend strength of
the end face plating
Without mechanical damage such as breaks.
2/4
MNR04
Resistors
!External dimensions (Units: mm)
2.0 0.2
a : 0.4 0.15
b : 0.3 0.15
a
b
No.
Material
Thick dielectric glaze of Ruthenium
Thick film of silver for primary electrode
Nickel-coated secondary electrode
External electrode coated with Sn/Pb or Sn
Alumina substrate
B
A
A'
∗
∗
∗
0.5
0.5
0.5
B'
Overcoating
Cross section A - A'
Cross section B - B'
∗ The pitch between electrodes.
!Equivalent circuit
R1
R2
R3
R4
R1 = R2 = R3 = R4
3/4
MNR04
Resistors
!Packaging
Reel
Taping
P
0
P
2
φD
0
E
F
A
0
W
A
B
D
P
1
Heat crimp cover / Tape
Thick paper mount
Chip network resistors
(Underside paper tape) Square punchout hole
T
2
C
Label
(Units : mm)
EIAJ ET-7200A compliant
W
F
E
A
0
B0
(Units : mm)
D
8.0 0.3
3.5 0.05
1.75 0.1
1.2 0.1
2.2 0.1
A
B
C
D
0
P
0
P
1
P
2
T2
0
−3
+1.0
0
+1
0
φ180
9
φ60
φ13 0.2
+0.1
4.0 0.1
2.0 0.1
2.0 0.05
Max. 0.5
φ1.5
0
!Product designation
Part no.
Packaging / Processing specifications
Circuit configuration Resistance Nominal resistance
code
tolerance
Packaging
Taping
Package style
Paper tape with reel (10,000)
Code Part no.
M0 MNR02 / 04
3-digit IEC coding system
AB MNR04 / 12 / 14 / 32 / 34
J
5%
4/4
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明