MNR34J5ABJ131 [ROHM]

Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.125W, 130ohm, 200V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 1220, CHIP;


型号：	MNR34J5ABJ131
厂家：	ROHM
描述：	Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.125W, 130ohm, 200V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 1220, CHIP 电阻器
文件：	总5页 (文件大小：76K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

MNR34

Resistors

Compact Chip Resistor Networks

MNR34 (3216×4 size)

zFeatures

1) Convex electrodes

Easy to check the fillet after soldering is finished.

2) Compatible with a wide range of mounting equipment.

Squared corners make it excellent for mounting using image recognition devices.

3) High-density mounting

Can be mounted even more densely than four 3216 chips (MCR18). Also, the number of parts and cost of mounting

have been reduced.

4) ROHM resistors have approved ISO9001- / ISO/TS 16949- certification.

Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with

the product before using or ordering it.

zRatings

Item

Conditions

Specifications

0.125W (1 / 8W)

Rated power

Power must be derated according to the power derating curve in

at 70°C

Figure 1 when ambient temperature exceeds 70°C.

100

−55

100 125

AMBIENT TEMPERATURE (°C)

Fig.1

Rated voltage

The voltage rating is calculated by the following equation.

If the value obtained exceeds the limiting element voltage,

the voltage rating is equal to the maximum operating voltage.

E: Rated voltage (V)

P: Rated power (W)

E= P×R

200V

Limiting element voltage

R: Nominal resistance (Ω)

Nominal resistance

Operating temperature

See Table 1.

−55°C to +125°C

Rev.E

1/4

MNR34

Resistors

Jumper type

Table 1

Max. 50mΩ

Resistance

Resistance range

Resistance temperature coefficient

Resistance tolerance

J ( 5%)

(Ω)

(ppm / °C)

Rated current

10 to 1M (E24)

200

Operating temperature

−55°C to +125°C

•Before using components in circuits where they will be exposed to transients such as pulse loads (short-duration, high-level loads), be certain to evaluate the

component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that

is greater than its rated voltage.

zCharacteristics

Guaranteed value

Item

Resistance

Test conditions (JIS C 5201-1)

JIS C 5201-1 4.5

Resistor type

J : 5%

Jumper type

Max. 50mΩ

Variation of resistance

with temperature

JIS C 5201-1 4.8

Measurement : −55 / +25 / +125°C

See Table.1

JIS C 5201-1 4.13

Rated voltage (current) ×2.5, 2s.

Limiting Element Voltage×2 : 400V

Overload

(2.0%+0.1Ω)

Max. 50mΩ

A new uniform coating of minimum of

95% of the surface being immersed

and no soldering damage.

JIS C 5201-1 4.17

Rosin·Ethanol (25%WT)

Soldering condition : 235 5°C

Duration of immersion : 2.0 0.5s.

Solderability

(1.0%+0.05Ω)

No remarkable abnormality on the appearance.

Max. 50mΩ

JIS C 5201-1 4.18

Soldering condition : 260 5°C

Duration of immersion : 10 1s.

Resistance to

soldering heat

(1.0%+0.05Ω)

(3.0%+0.1Ω)

Max. 50mΩ

JIS C 5201-1 4.19

Test temp. : −55°C to +125°C 5cyc

Rapid change of

temperature

JIS C 5201-1 4.24

40°C, 93%RH

Test time : 1,000h to 1,048h

Damp heat, steady state

(3.0%+0.1Ω)

Max. 50mΩ

JIS C 5201-1 4.25.1

Rated voltage (current), 70°C

1.5h : ON − 0.5h : OFF

Test time : 1,000h to 1,048h

Endurance at 70°C

(3.0%+0.1Ω)

(1.0%+0.05Ω)

Max. 50mΩ

JIS C 5201-1 4.25.3

125°C

Endurance

Test time : 1,000h to 1,048h

JIS C 5201-1 4.29

23 5°C, Immersion cleaning, 5 0.5min.

Solvent : 2-propanol

Resistance to solvent

JIS C 5201-1 4.33

Bend strength of

the end face plating

Without mechanical damage such as breaks.

Rev.E

2/4

MNR34

Resistors

zDimensions (Unit : mm)

5.2 0.4

Cross section A-A'

∗

No.

Material

1.27

Resistive element

(Oxide metal thick film)

Cross section B-B'

Silver thick film electrode

Nickel electrode

A 1 0 3

Sn electrode

0.55 0.1

Alumina substrate

Overcoating (Glass)

0.5 0.2

1.0 0.2

0.8 0.2

Pitch of the upper electrode.

∗

zEquivalent circuit

R1=R2=R3=R4

zPackaging

Reel

Taping

(Unit: mm)

Label

1.75 0.1

EIAJ ET-7200B compliant

12.0 0.3

5.5 0.05

3.4 0.1

5.6 0.1

(Unit: mm)

+0.1

4.0 0.1

2.0 0.05

1.0 0.15

4.0 0.1

φ1.5

−1.5

+1.0

−0

φ60

φ180

φ13 0.2

Rev.E

3/4

MNR34

Resistors

zPart No. Explanation

J 5

3 4

Part No.

Resistance tolerance Nominal resistance

Resistance code, 3 digits,

000 denotes Jumper type.

J is also used

for jumper.

Packaging Specifications Code

Resistance tolerance

Part No. Code

Packaging specifications

Reel

φ180mm (7in).

Basic ordering unit (pcs)

J( 5%)

MNR34 J5AB

Embossed tape (4mmPitch)

4,000

Reel (φ180mm) : Compatible with JEITA standard "EIAJ ET-7200B"

: Standard product

Rev.E

4/4

Appendix

Notes

No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM

CO.,LTD.

The content specified herein is subject to change for improvement without notice.

The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you

wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM

upon request.

Examples of application circuits, circuit constants and any other information contained herein illustrate the

standard usage and operations of the Products. The peripheral conditions must be taken into account when

designing circuits for mass production.

Great care was taken in ensuring the accuracy of the information specified in this document. However, should

you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no respon-

sibility for such damage.

The technical information specified herein is intended only to show the typical functions of and examples of

application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or

exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility

whatsoever for any dispute arising from the use of such technical information.

The Products specified in this document are intended to be used with general-use electronic equipment or

devices (such as audio visual equipment, office-automation equipment, communication devices, electronic

appliances and amusement devices).

The Products are not designed to be radiation tolerant.

While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or

malfunction for a variety of reasons.

Please be sure to implement in your equipment using the Products safety measures to guard against the

possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as

derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your

use of any Product outside of the prescribed scope or not in accordance with the instruction manual.

The Products are not designed or manufactured to be used with any equipment, device or system

which requires an extremely high level of reliability the failure or malfunction of which may result in a direct

threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment,

aerospace machinery, nuclear-reactor controller, fuel-controller or other safety device). ROHM shall bear no

responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended

to be used for any such special purpose, please contact a ROHM sales representative before purchasing.

If you intend to export or ship overseas any Product or technology specified herein that may be controlled under

the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law.

Thank you for your accessing to ROHM product informations.

More detail product informations and catalogs are available, please contact your nearest sales office.

THE AMERICAS / EUROPE / ASIA / JAPAN

ROHM Customer Support System

www.rohm.com

TEL : +81-75-311-2121

FAX : +81-75-315-0172

21 Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan

Appendix1-Rev3.0

相关型号：