MNR34J5ABJ [ROHM]

Chip resistor networks; 片式电阻网络


型号：	MNR34J5ABJ
厂家：	ROHM
描述：	Chip resistor networks 片式电阻网络
文件：	总6页 (文件大小：103K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

MNR34

Resistors

Chip resistor networks

MNR34 (3216×4 size)

zFeatures

1) Convex electrodes

Easy to check the fillet after soldering is finished.

2) Compatible with a wide range of mounting equipment.

Squared corners make it excellent for mounting using image recognition devices.

3) High-density mounting

Can be mounted even more densely than four 3216 chips (MCR18). Also, the number of parts and cost of mounting

have been reduced.

4) ROHM resistors have approved ISO-9001 certification.

Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with

the product before using or ordering it.

zRatings

Item

Conditions

Specifications

0.125W (1 / 8W)

Rated power

Power must be derated according to the power derating curve in

at 70°C

Figure 1 when ambient temperature exceeds 70°C.

100

−55

100 125

AMBIENT TEMPERATURE (°C)

Fig.1

Rated voltage

The voltage rating is calculated by the following equation.

If the value obtained exceeds the limiting element voltage,

the voltage rating is equal to the maximum operating voltage.

E: Rated voltage (V)

P: Rated power (W)

E= P×R

200V

Limiting element voltage

R: Nominal resistance (Ω)

Nominal resistance

Operating temperature

See Table 1.

−55°C to +125°C

Rev.A

1/5

MNR34

Resistors

Jumper type

Table 1

Resistance range

Resistance temperature coefficient

(ppm / °

Max. 50mΩ

Resistance

Resistance tolerance

J ( 5%)

(Ω)

Rated current

10≤R≤1M (E24)

200

Operating temperature

−55°C to +125°C

•Before using components in circuits where they will be exposed to transients such as pulse loads (short-duration, high-level loads), be certain to evaluate the

component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that

is greater than its rated voltage.

zCharacteristics

Guaranteed value

Item

Resistance

Test conditions (JIS C 5201-1)

JIS C 5201-1 4.5

Resistor type

J : 5%

Jumper type

Max. 50mΩ

Variation of resistance

with temperature

JIS C 5201-1 4.8

Measurement : −55 / +25 / +125°C

See Table.1

JIS C 5201-1 4.13

Rated voltage (current) ×2.5, 2s.

Limiting Element Voltage×2 : 400V

Overload

(2.0%+0.1Ω)

Max. 50mΩ

A new uniform coating of minimum of

95% of the surface being immersed

and no soldering damage.

JIS C 5201-1 4.17

Rosin·Ethanol (25%WT)

Soldering condition : 235 5°C

Duration of immersion : 2.0 0.5s.

Solderability

(1.0%+0.05Ω)

No remarkable abnormality on the appearance.

Max. 50mΩ

JIS C 5201-1 4.18

Soldering condition : 260 5°C

Duration of immersion : 10 1s.

Resistance to

soldering heat

(1.0%+0.05Ω)

(3.0%+0.1Ω)

Max. 50mΩ

JIS C 5201-1 4.19

Test temp. : −55°C to +125°C 5cyc

Rapid change of

temperature

JIS C 5201-1 4.24

40°C, 93%RH

Test time : 1,000h to 1,048h

Damp heat, steady state

(3.0%+0.1Ω)

Max. 50mΩ

JIS C 5201-1 4.25.1

Rated voltage (current), 70°C

1.5h : ON − 0.5h : OFF

Test time : 1,000h to 1,048h

Endurance at 70°C

(3.0%+0.1Ω)

(1.0%+0.05Ω)

Max. 50mΩ

JIS C 5201-1 4.25.3

125°C

Endurance

Test time : 1,000h to 1,048h

JIS C 5201-1 4.29

23 5°C, Immersion cleaning, 5 0.5min.

Solvent : 2-propanol

Resistance to solvent

JIS C 5201-1 4.33

Bend strength of

the end face plating

Without mechanical damage such as breaks.

Rev.A

2/5

MNR34

Resistors

zExternal dimensions (Unit : mm)

5.2 0.4

Cross section A-A'

∗

No.

Material

1.27

Thick dielectric glaze of oxide metal

(only silver used for jumper)

Cross section B-B'

Thick film of silver for electrode

Nickel-coated electrode

Sn electrode

A 1 0 3

0.55 0.1

Alumina substrate

Overcoating

0.5 0.2

1.0 0.2

0.8 0.2

Pitch of the upper electrode.

∗

zEquivalent circuit

R1=R2=R3=R4

zPackaging

Reel

Taping

(Unit: mm)

Label

1.75 0.1

EIAJ ET-7200B compliant

12.0 0.3

5.5 0.05

3.4 0.1

5.6 0.1

(Unit: mm)

+0.1

4.0 0.1

2.0 0.05

1.0 0.15

4.0 0.1

φ1.5

−1.5

+1.0

−0

φ60

φ180

φ13 0.2

Rev.A

3/5

MNR34

Resistors

zProduct designation

J 5

3 4

Part No.

Resistance tolerance Nominal resistance

Resistance code, 3 digits,

000 denotes Jumper type.

J is also used

for jumper.

Packaging Specifications Code

Resistance tolerance

Part No. Code

Packaging specifications

Reel

φ180mm (7in).

Basic ordering unit (pcs)

J( 5%)

MNR34 J5AB

Embossed tape (4mmPitch)

4,000

Reel (φ180mm) : Compatible with JEITA standard "EIAJ ET-7200B"

: Standard product

zElectrical characteristics

400

300

6.0

JIS C 5201-1 4.13

JIS C 5201-1 4.8

SAMPLE SIZE : n=20pcs

25°C / −55°C 25°C / 125°C

JIS C 5201-1 4.5

SAMPLE SIZE : n=40pcs

20°C 65%RH

SAMPLE SIZE : n=20pcs

RATED VOLTAGE × 2.5TIMES 2s

LIMITING ELEMENT

4.0

200

VOLTAGE×2 : 400V

2.0

100

−100

−200

−300

−400

−2.0

−4.0

−6.0

−2.0

−4.0

−6.0

100

10k 100k

100

10k 100k

100

10k 100k

RESISTANCE (Ω)

Fig.2 Resistance

Fig.4 Overload

Fig.3 Variation resistance with

temperature

3.0

2.0

3.0

2.0

6.0

4.0

2.0

JIS C 5201-1 4.18

SAMPLE SIZE : n=20pcs

SOLDERING CONDITION

JIS C 5201-1 4.19

SAMPLE SIZE : n=20pcs

−55°C / 125°C 5cyc

JIS C 5201-1 4.24

SAMPLE SIZE : n=20pcs

40°C 93%RH WITH NO LOAD

1,000h

: 260°C 10s

1.0

−1.0

−2.0

−3.0

−2.0

−1.0

−2.0

−3.0

−4.0

−6.0

100

10k 100k

100

10k 100k

100

10k 100k

RESISTANCE (Ω)

Fig.6 Rapid change of

temperature

Fig.5 Resistance to soldering heat

Fig.7 Damp heat, steady state

Rev.A

4/5

MNR34

Resistors

2.0

1.5

6.0

4.0

6.0

4.0

JIS C 5201-1 4.25.1

SAMPLE SIZE : n=20pcs

70°C 1,000h

OVERLOAD : THE RATED

VOLTAGE

JIS C 5201-1 4.29

SAMPLE SIZE : n=20pcs

IPA, 5min.

JIS C 5201-1 4.25.3

SAMPLE SIZE : n=20pcs

125°C WITH NO LOAD 1,000h

1.0

2.0

0.5

−0.5

−1.0

−1.5

−2.0

−4.0

−6.0

−2.0

−4.0

−6.0

100

10k 100k

100

10k 100k

100

10k 100k

RESISTANCE (Ω)

Fig.9 Endurance

Fig.8 Endurance at 70°C

Fig.10 Resistance to solvents

Rev.A

5/5

Appendix

Notes

No technical content pages of this document may be reproduced in any form or transmitted by any

means without prior permission of ROHM CO.,LTD.

The contents described herein are subject to change without notice. The specifications for the

product described in this document are for reference only. Upon actual use, therefore, please request

that specifications to be separately delivered.

Application circuit diagrams and circuit constants contained herein are shown as examples of standard

use and operation. Please pay careful attention to the peripheral conditions when designing circuits

and deciding upon circuit constants in the set.

Any data, including, but not limited to application circuit diagrams information, described herein

are intended only as illustrations of such devices and not as the specifications for such devices. ROHM

CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any

third party's intellectual property rights or other proprietary rights, and further, assumes no liability of

whatsoever nature in the event of any such infringement, or arising from or connected with or related

to the use of such devices.

Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or

otherwise dispose of the same, no express or implied right or license to practice or commercially

exploit any intellectual property rights or other proprietary rights owned or controlled by

ROHM CO., LTD. is granted to any such buyer.

Products listed in this document are no antiradiation design.

The products listed in this document are designed to be used with ordinary electronic equipment or devices

(such as audio visual equipment, office-automation equipment, communications devices, electrical

appliances and electronic toys).

Should you intend to use these products with equipment or devices which require an extremely high level of

reliability and the malfunction of with would directly endanger human life (such as medical instruments,

transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other

safety devices), please be sure to consult with our sales representative in advance.

About Export Control Order in Japan

Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control

Order in Japan.

In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause)

on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction.

Appendix1-Rev1.1

相关型号：