PMR10EZPFU6L00 [ROHM]

Ultra-Low Ohmic Resistors for Current Detection; 超低阻值电阻器的电流检测


型号：	PMR10EZPFU6L00
厂家：	ROHM
描述：	Ultra-Low Ohmic Resistors for Current Detection 超低阻值电阻器的电流检测电阻器
文件：	总5页 (文件大小：150K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

Ultra-Low Ohmic Resistors for Current Detection

PMR10

Features

1) Ultra low-ohmic resistance range (2m~)

2) Improved current detection accuracy by trimming-less structure.

Highly recommended for large current / High speed switching circuit.

3) Completely Pb free product

4) ISO9001- / ISO/TS 16949-approved

Ratings

Item

Conditions

Specifications

0.5W (1 / 2W)

For resistors operated at the ambient temperature in

excess of 70 , the load shall be derated in accordance with Fig.1

Rated power

at 70°C

100

−55

100 125

155

AMBIENT TEMPERATURE (°C)

Fig.1

Rated voltage

Rated current

Rated voltage and current are determined from the following.

E: Rated voltage (V)

E= P×R

I : Rated current (A)

P: Rated power (W)

R: Nominal resistance (Ω)

I = P / R

Nominal resistance

See Table 1.

−55°C to +155°C

Operating temperature

Table.1

RESISTANCE

SPECIAL

CODE

TEMPERATURE

COEFFICIENT (ppm / ˚C)

TOLERANCE

(mΩ)

2,3,4

F ( 1%)

G ( 2%)

J ( 5%)

150

5,6,7,8,9,10

www.rohm.com

2010.09 - Rev.D

1/4

PMR10

Data Sheet

Characteristics

Guaranteed value

Resistor type

Item

Test conditions (JIS C 5201-1)

JIS C 5201-1 4.5

Measuring method : Measure under

terminations by 4 probes.

F : 1%

G : 2%

J : 5%

Fig.2 (Under terminations)

Resistance

probes

Variation of resistance

with temperature

JIS C 5201-1 4.8

Measurement : 25 / −55 / +25 / +125°C

See Table.1

2.0%

JIS C 5201-1 4.13

Rated power ×2.5, 2s.

Overload

JIS C 5201-1 4.17

A new uniform coating of minimum of

95% of the surface being immersed

and no soldering damage.

Rosin·Ethanol (25%WT)

Soldering condition : 235 5°C

Duration of immersion : 2.0 0.5s.

Solderability

JIS C 5201-1 4.18

Soldering condition : 260 5°C

Duration of immersion : 10 1s.

1.0%

Resistance to

soldering heat

No remarkable abnormality on the appearance.

JIS C 5201-1 4.19

Test temp. : −55°C to +125°C 5cyc

Rapid change of

temperature

1.0%

3.0%

JIS C 5201-1 4.24

40°C, 93%RH

Test time : 56days

Damp heat, steady state

JIS C 5201-1 4.25.1

70°C,Rated power

1.5h : ON − 0.5h : OFF

Test time : 1,000h to 1,048h

3.0%

Endurance at 70°C

JIS C 5201-1 4.25.3

155°C

3.0%

0.5%

Endurance

Test time : 1,000h to 1,048h

JIS C 5201-1 4.29

23 5°C

Solvent : 2-propanol

Resistance to solvent

JIS C 5201-1 4.33

Bend strength of

the end face plating

Without open

www.rohm.com

2010.09 - Rev.D

2/4

PMR10

Data Sheet

Dimensions&Construction

Measure

Resistance

0.15

0.25

(The Surface)

2mΩ

0.55

5L00

0.75

0.60

0.45

0.55

0.45

0.35

0.40

0.35

3mΩ

4mΩ

0.42

5mΩ

6mΩ

7mΩ

8mΩ

9mΩ

10mΩ

2.00

1.20

0.32

0.28

(The back)

No.

①

②

③

④

⑤

Material

⑤

④

Resistive metal element (Ni-Cu/Ni-Cr Alloy)

Primary electrode(Cu)

①

(The cross section)

External electrode(Sn)

②

③

④

Overcoat (Resin : Black)

Marking (Resin :Yellow)

Part No. Explanation

P M R 1 0 E Z P

Part No.

Resistance tolerance

Special part number

Nominal resistance

5 to 10mΩ

2 to 4mΩ

Resistance code, 3 or 4 digits.

Resistance

tolerance

Resistance

code

F,G

4 digits

3 digits

Resistance Tolerance

Resistance

Value (Ω)

F,G

2mΩ

3mΩ

4mΩ

5mΩ

6mΩ

7mΩ

8mΩ

9mΩ

10mΩ

2L0

3L0

4L0

5L0

6L0

7L0

8L0

9L0

10L

2L00

3L00

4L00

5L00

6L00

7L00

8L00

9L00

10L0

Packaging Specifications Code

Resistance tolerance

Part No.

Code

EZP

Packaging specifications

Paper tape (4mm Pitch)

Reel

Basic ordering unit (pcs)

J( 5%) G( 2%)

F(±1%)

PMR10

180mm (7in.)

5 000

Reel (φ180) : Compatible with JEITA standard "EIAJ ET-7200B"

: Standard product

www.rohm.com

2010.09 - Rev.D

3/4

PMR10

Data Sheet

Packaging

Reel

Taping

Top tape

Base paper

Components

Cavity

Bottom Tape

Label

(Unit : mm)

EIAJ ET-7200B compliant

(Unit : mm)

+0.2

-0.1

+0.2

-0.1

8.0 0.3

3.5 0.05

1.75 0.1 1.65

2.4

+1.0

4.0 0.1

2.0 0.05

Max. 1.1

www.rohm.com

2010.09 - Rev.D

4/4

Notice

N o t e s

No copying or reproduction of this document, in part or in whole, is permitted without the

consent of ROHM Co.,Ltd.

The content speciﬁed herein is subject to change for improvement without notice.

The content speciﬁed herein is for the purpose of introducing ROHM's products (hereinafter

"Products"). If you wish to use any such Product, please be sure to refer to the speciﬁcations,

which can be obtained from ROHM upon request.

Examples of application circuits, circuit constants and any other information contained herein

illustrate the standard usage and operations of the Products. The peripheral conditions must

be taken into account when designing circuits for mass production.

Great care was taken in ensuring the accuracy of the information speciﬁed in this document.

However, should you incur any damage arising from any inaccuracy or misprint of such

information, ROHM shall bear no responsibility for such damage.

The technical information speciﬁed herein is intended only to show the typical functions of and

examples of application circuits for the Products. ROHM does not grant you, explicitly or

implicitly, any license to use or exercise intellectual property or other rights held by ROHM and

other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the

use of such technical information.

The Products speciﬁed in this document are intended to be used with general-use electronic

equipment or devices (such as audio visual equipment, ofﬁce-automation equipment, commu-

nication devices, electronic appliances and amusement devices).

The Products speciﬁed in this document are not designed to be radiation tolerant.

While ROHM always makes efforts to enhance the quality and reliability of its Products, a

Product may fail or malfunction for a variety of reasons.

Please be sure to implement in your equipment using the Products safety measures to guard

against the possibility of physical injury, ﬁre or any other damage caused in the event of the

failure of any Product, such as derating, redundancy, ﬁre control and fail-safe designs. ROHM

shall bear no responsibility whatsoever for your use of any Product outside of the prescribed

scope or not in accordance with the instruction manual.

The Products are not designed or manufactured to be used with any equipment, device or

system which requires an extremely high level of reliability the failure or malfunction of which

may result in a direct threat to human life or create a risk of human injury (such as a medical

instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuel-

controller or other safety device). ROHM shall bear no responsibility in any way for use of any

of the Products for the above special purposes. If a Product is intended to be used for any

such special purpose, please contact a ROHM sales representative before purchasing.

If you intend to export or ship overseas any Product or technology speciﬁed herein that may

be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to

obtain a license or permit under the Law.

Thank you for your accessing to ROHM product informations.

More detail product informations and catalogs are available, please contact us.

ROHM Customer Support System

http://www.rohm.com/contact/

www.rohm.com

R1010

相关型号：