5.0SMDJ60A [RUILON]

Transient Voltage Suppressors; 瞬态电压抑制器


型号：	5.0SMDJ60A
厂家：	Ruilongyuan Electronics Co.,Ltd
描述：	Transient Voltage Suppressors 瞬态电压抑制器
文件：	总7页 (文件大小：952K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

ELECTRONICS

Transient

Voltage

Suppressors

5.0SMDJ Series

Speciﬁcations are subject to change without notice.

Circuit Protection

System

Please refer to http://www.ruilon.com for current information.

Transient Voltage Suppressors - 5.0SMDJ Series

UNI

Features

1. Halogen-free

2. Rohs compliant

3. Typical maximum temperature coefﬁcient

4. ΔV = 0.1% x V @25°C x ΔT

5. Glass passivated Chip junction in DO-214AB package

6. 5000W peak pulse capadility at 10×1000μs waveform, repetition rate (duty

cycles):0.01%

7. Fast response time:typically less than 1.0ps from 0 Volts to BV min

8. Excellent clamping capability

9. Low incremental surge resistance

10. Typical IR less than 5μA above 12V

Cathode

Anode

11. High temperature soldering guaranteed: 260°C/40 seconds / 0.375”,

12. (9.5mm) lead length, 5lbs., (2.3kg) tension

13. Plastic package has underwriters laboratory ﬂammability classiﬁcation

94v-0

UNI

Applications

TVS devices are ideal for the protection of I/O interfaces,VCC bus and other vulnerable circuits used in telecom, computer,

industrial and consumer electronic applications.

Mechanical Characteristics

Rating

Symbol

P_PPM

P_D

Value

5000

6.5

Units

Watts

Amps

Peak Pulse Power Dissipation at TA=25°C by 10/1000μs

Waveform (Fig.2)(Note 1), (Note 2)

Power Dissipation on Inﬁnite Heat

Sink at TA=50°C

Peak Forward Surge Current, 8.3ms

Single Half Sine Wave (Note 3)

IFSM

300

Maximum Instantaneous Forward Voltage at 100A for

Unidirectional Only

V_F

5.0

Operating junction and Storage Temperature Range.

Typical Thermal Resistance Junction to Lead

T T

-55°C to 150°C

°C

STG

R_uJL

R_uJA

°C/W

Typical Thermal Resistance Junction

to Ambient

Notes:

1. Non-repetitive current pulse , per Fig. 4 and derated above TA = 25°C per Fig. 3.

2. Mounted on copper pad area of 0.31x0.31” (8.0 × 8.0mm) to each terminal.

3. Measured on 8.3ms single half sine wave or equivalent square wave for unidirectional device only,duty cycle=4 per minute

maximum.

Speciﬁcations are subject to change without notice.

Circuit Protection

System

Page:1

Please refer to http://www.ruilon.com for current information.

Transient Voltage Suppressors - 5.0SMDJ Series

Electriacl Characteristics

Reverse

Stand-Off

Voltage

Maximum

Clamping

Reverse

Leakage

Device Marking

Test

Current

Peak Pulse

Current

Type Number

Code

Breakdown Voltage@I

Voltage@I

RWM

I (µA)

(UNI)

(BI)

UNI

(V)

(V) V

(V)

I (mA)

V (V)

(A)

RWM

BR MIN.

13.30

14.40

15.60

16.70

17.80

18.90

20.00

22.20

24.40

26.70

28.90

31.10

33.30

36.70

40.00

44.40

47.80

50.00

53.30

56.70

60.00

64.40

66.70

71.10

77.80

83.30

86.70

94.40

100.00

111.00

122.00

133.00

140.00

167.00

178.00

189.00

BR MAX.

14.70

15.90

17.20

18.50

19.70

20.90

22.10

24.50

26.90

29.50

31.90

34.40

36.80

40.60

44.20

49.10

52.80

55.30

58.90

62.70

66.30

71.20

73.70

78.60

86.00

92.10

95.80

104.00

111.00

123.00

135.00

147.00

159.00

185.00

197.00

209.00

5.0SMDJ12A 5.0SMDJ12CA 5PEP 5BEP

5.0SMDJ13A 5.0SMDJ13CA 5PEQ 5BEQ

5.0SMDJ14A 5.0SMDJ14CA 5PER 5BER

5.0SMDJ15A 5.0SMDJ15CA 5PES 5BES

5.0SMDJ16A 5.0SMDJ16CA 5PET 5BET

5.0SMDJ17A 5.0SMDJ17CA 5PEU 5BEU

5.0SMDJ18A 5.0SMDJ18CA 5PEV 5BEV

5.0SMDJ20A 5.0SMDJ20CA 5PEW 5BEW

5.0SMDJ22A 5.0SMDJ22CA 5PEX 5BEX

5.0SMDJ24A 5.0SMDJ24CA 5PFZ 5BFZ

5.0SMDJ26A 5.0SMDJ26CA 5PFE 5BFE

5.0SMDJ28A 5.0SMDJ28CA 5PFG 5BFG

5.0SMDJ30A 5.0SMDJ30CA 5PFK 5BFK

5.0SMDJ33A 5.0SMDJ33CA 5PFM 5BFM

5.0SMDJ36A 5.0SMDJ36CA 5PFP 5BFP

5.0SMDJ40A 5.0SMDJ40CA 5PFR 5BFR

5.0SMDJ43A 5.0SMDJ43CA 5PFT 5BFT

5.0SMDJ45A 5.0SMDJ45CA 5PFV 5BFV

5.0SMDJ48A 5.0SMDJ48CA 5PFX 5BFX

5.0SMDJ51A 5.0SMDJ51CA 5PFZ 5BFZ

5.0SMDJ54A 5.0SMDJ54CA 5PGE 5BGE

5.0SMDJ58A 5.0SMDJ58CA 5PGG 5BGG

5.0SMDJ60A 5.0SMDJ60CA 5PGK 5BGK

5.0SMDJ64A 5.0SMDJ64CA 5PGM 5BGM

5.0SMDJ70A 5.0SMDJ70CA 5PGP 5BGP

5.0SMDJ75A 5.0SMDJ75CA 5PGR 5BGR

5.0SMDJ78A 5.0SMDJ78CA 5PGT 5BGT

5.0SMDJ85A 5.0SMDJ85CA 5PGV 5BGV

5.0SMDJ90A 5.0SMDJ90CA 5PGX 5BGX

5.0SMDJ100A 5.0SMDJ100CA 5PHZ 5BHZ

5.0SMDJ110A 5.0SMDJ110CA 5PHE 5BHE

5.0SMDJ120A 5.0SMDJ120CA 5PHG 5BHG

5.0SMDJ130A 5.0SMDJ130CA 5PHK 5BHK

5.0SMDJ150A 5.0SMDJ150CA 5PHM 5BHM

5.0SMDJ160A 5.0SMDJ160CA 5PHP 5BHP

5.0SMDJ170A 5.0SMDJ170CA 5PHR 5BHR

12.0

13.0

14.0

15.0

16.0

17.0

18.0

20.0

22.0

24.0

26.0

28.0

30.0

33.0

36.0

40.0

43.0

45.0

48.0

51.0

54.0

58.0

60.0

64.0

70.0

75.0

78.0

85.0

90.0

100.0

110.0

120.0

130.0

150.0

160.0

170.0

19.9

21.5

252.00

233.00

216.00

205.00

193.00

181.00

172.00

155.00

141.00

129.00

119.00

110.00

103.00

93.90

86.10

77.60

72.10

68.80

64.70

60.70

57.50

53.50

51.70

48.60

44.30

41.40

39.70

36.50

34.30

30.90

28.30

26.00

24.00

20.60

19.30

18.20

800

500

200

100

23.2

24.4

26.0

27.6

29.2

32.4

5.0

35.5

38.9

42.1

45.4

48.4

53.3

58.1

64.5

69.4

72.7

77.4

82.4

87.1

93.6

96.8

103.0

113.0

121.0

126.0

137.0

146.0

162.0

177.0

193.0

209.0

243.0

259.0

275.0

For bidirectional type having VR of 10 volts and less, the IR limit is double.

For parts without A, the VBR is +10% and VC is 5% higher than with A parts.

Speciﬁcations are subject to change without notice.

Circuit Protection

System

Page:2

Please refer to http://www.ruilon.com for current information.

Transient Voltage Suppressors - 5.0SMDJ Series

Ratings and Characteristic Curves

Figure 1 - Peak Pulse Power Rating Curve

Figure 2 - Pulse Derating Curve

Figure 3 - Pulse Waveform

Figure 4 - Typical Junction Capacitance

100000

Bi-directional V= OV

Uni-directional V= OV

10000

1000

100

Uni-directional @ VR

Bi-directional @ VR

1.0

10.0

100.0

1000.0

V_BR- Reverse Breakdown Voltage (V)

Figure 5 - Steady State Power Derating Curve

Figure 6 - Maximum Non-Repetitive Peak Forward

Surge Current Uni-Directional Only

Speciﬁcations are subject to change without notice.

Circuit Protection

System

Page:3

Please refer to http://www.ruilon.com for current information.

Transient Voltage Suppressors - 5.0SMDJ Series

Soldering Parameters

Feﬂow Condition

Lead-free assembly

- Temperature Min (T

- Temperature Max (T

)

150°C

200°C

s(min)

Pre Heat

)

s(min)

- Time (min to max) (t )

60-180 secs

3°C/second max

217°C

Average ramp up rate (Liquidus Temp (T ) to peak

to T - Ramp-up Rate

S(max)

- Temperature (T ) (Liquidus)

Reﬂow

- Time (min to max) (t )

60-150 seconds

+0/-5

°C

Peak Temperature (T

)

260

Time within 5°C of actual peak Temperature (t )

20-40 seconds

6°C/second max

8 minutes Max.

280°C

Ramp-down Rate

Time 25°C to peak Temperature (T

Do not exceed

)

Physical Speciﬁcations

t_p

T_P

one

Weight

0.007 ounce, 0.21 grams

Ramp-up

Critical Z

to T

JEDEC DO214AA. Molded plastic body

over glass passivated junction

Color band denotes cathode except

Bidirectional.

Matte Tin-plated leads, Solderable per

JESD22-B102D

T_L

t_L

Case

T_s(max)

Polarity

Termina

Ramp-down

T_s(min)

t_s

Preheat

Time (t)

Environmental Speciﬁcations

Temperature Cycle

Pressure Cooker

High Temp. Storage

HTRB

JESD22-A104

JESD 22-A102

JESD22-A103

JESD22-A108

JESD22-A106

Thermal Shock

Speciﬁcations are subject to change without notice.

Circuit Protection

System

Page:4

Please refer to http://www.ruilon.com for current information.

Transient Voltage Suppressors - 5.0SMDJ Series

Dimensions

Unit:mm

Millimeters

DO-214AB (SMC J-Bend)

Inches

DIM

Max

0.126

0.280

0.245

0.103

0.060

0.008

0.320

0.012

Min

2.900

6.600

5.590

2.060

0.760

Max

3.200

7.110

6.220

2.620

1.520

0.203

8.130

0.305

Min

0.114

0.260

0.220

0.079

0.030

0.305

0.006

0.129

0.094

7.750

0.152

3.300

24.00

0.165

4.200

0.094

2.400

Part Numbering System

5.0SMDJ

XXX C A

5% VOLTAGE TOLERANCE

BI-DIRECTIONAL

VOLTAGE

SERIES

Packaging

Component

Package

Packaging

Option

Part Number

Quantity

Packaging Speciﬁcation

5.0SMDJxxxXX

DO-214AB

3000

500

Tape & Reel-16mm/13''tape

Tape & Reel – 16mm/7” tape

EIA STD RS-481

5.0SMDJxxxXX-T7

Speciﬁcations are subject to change without notice.

Circuit Protection

System

Page:5

Please refer to http://www.ruilon.com for current information.

RuiLongYuan Electronics Co., Ltd.

· Reproducing and modifying information of the document is prohibited without permission from

Ruilongyuan International Inc.

· Ruilongyuan International Inc. reserves the rights to make changes of the content herein the document anytime

without notiﬁcation. Please refer to our website for the latest document.

· Ruilongyuan International Inc. disclaims any and all liability arising out of the application or use of any product

including damages incidentally and consequentially occurred.

· Ruilongyuan International Inc. does not assume any and all implied warranties, including warranties of ﬁtness

for particular purpose, non-infringement and merchantability.

· Applications shown on the herein document are examples of standard use and operation. Customers are responsible

in comprehending the suitable use in particular applications.Ruilongyuan International Inc. makes no representation or

warranty that such applications will be suitable for the specifed use without further testing or modifcation.

· The products shown herein are not designed and authorized for equipments requiring high level of reliability or relating to

human life and for any applications concerning life-saving or life-sustaining, such as medical instruments, transportation

equipment,aerospace machinery et cetera. Customers using or selling these products for use in such applications do so at

their own risk and agree to fullyindemnify Ruilongyuan International Inc. for any damages resulting from such improper use or

sale.

Tel: +86-755-8290 8296

Fax: +86-755-8290 8002

E-mail: jack@ruilon.com

Speciﬁcations are subject to change without notice.

Circuit Protection

System

Page:6

Please refer to http://www.ruilon.com for current information.

相关型号：