首页 |元器件品牌

RFA6T-79RP4-78SP3-0300 [SAMTEC]

Cable Assembly;
RFA6T-79RP4-78SP3-0300
型号： RFA6T-79RP4-78SP3-0300
厂家： SAMTEC    SAMTEC
描述：

Cable Assembly
文件： 总3页 (文件大小：599K)
中文：  中文翻译
下载：  下载PDF数据表文档文件
 查看货源
RFX6T-XXXXX-XXXXXX-XXXX  
DESIGNED & DIMENSIONED  
REVISION R  
IN MILLIMETERS[INCHES] CABLE CALLOUT  
OVERALL CABLE LENGTH  
MILLIMETERS OF CABLE  
0300 MIN. (SEE NOTE 8 & 9)  
A: CCA-6 (RG-6 CABLE)  
B: CCA-1694A (BELDEN 1694A CABLE)  
DO NOT  
SCALE FROM  
THIS PRINT  
FIG 2  
CABLE STRIPPING DIMENSIONS  
END 2 PLATING OPTION  
END 1 CONNECTOR  
PER CONFIGURATIONS  
2. GOLD / NICKEL COMBINATION  
-74RP: BNC7T-P-C-XX-RA-CA6 (SEE SHEET 2)  
-74SP: BNC7T-P-C-XX-ST-CA6 (SEE SHEET 2)  
-D4SP: BNC7T-P-C-XX-ST-CA6D (SEE SHEET 2)  
-78SP: DIN7A-PP-C-XX-ST-CA6 (SEE SHEET 3)  
-79SP: MBNC7-P-C-XX-ST-CA6 (SEE SHEET 3)  
-79RP: MBNC7-P-C-XX-RA-CA6 (SEE SHEET 3)  
-H4SP: HDBNC-P-C-XX-ST-CA6 (SEE SHEET 2)  
(SEE TABLE 1)(SEE NOTE 12,13,14,15)  
3: ALTERNATE GOLD / NICKEL  
4. ALTERNATE GOLD / GOLD FLASH / NICKEL  
5. ALTERNATE GOLD / GOLD / NICKEL  
6. ALTERNATE H GOLD / H GOLD / NICKEL  
8. ALTERNATE HEAVY GOLD / GOLD FLASH /NICKEL  
(SEE SHEET 2 AND 3 FOR PLATING SPECIFICS)  
(LEAVE BLANK FOR -SING OR -XXXXXX  
END 2 PREPARATION)  
"A" mm  
"B" mm  
"C" mm  
C
END 1 PLATING OPTION  
END 2 CONNECTOR OR PREPARATION  
2. GOLD / NICKEL COMBINATION  
C
C
"D" mm  
"E" mm  
-74RP: BNC7T-P-C-XX-RA-CA6 (SEE SHEET 2)  
-74SP: BNC7T-P-C-XX-ST-CA6 (SEE SHEET 2)  
-D4SP: BNC7T-P-C-XX-ST-CA6D (SEE SHEET 2)  
-78SP: DIN7A-PP-C-XX-ST-CA6 (SEE SHEET 3)  
-79SP: MBNC7-P-C-XX-ST-CA6 (SEE SHEET 3)  
-79RP: MBNC7-P-C-XX-RA-CA6 (SEE SHEET 3)  
-H4SP: HDBNC-P-C-XX-ST-CA6 (SEE SHEET 2)  
-SING: SINGLE ENDED (ONE END ONLY, SEE NOTE 11)  
-XXXXXX: STRIPPED AND TINNED (ONE END ONLY-  
SEE NOTES 11-15 & 17, SHEET 2, FIG 3)  
3: ALTERNATE GOLD / NICKEL  
4. ALTERNATE GOLD / GOLD FLASH / NICKEL  
5. ALTERNATE GOLD / GOLD / NICKEL  
6. ALTERNATE H GOLD / H GOLD / NICKEL  
8. ALTERNATE HEAVY GOLD / GOLD FLASH /NICKEL  
(SEE SHEET 2 AND 3 FOR PLATING SPECIFICS)  
(SEE FIG. 2) "C" FORMAT: X.X mm  
(SEE FIG. 2) "B" FORMAT: X.X mm  
(SEE FIG. 2) "A" FORMAT: X.X mm  
DO NOT LEAVE ANY SPACE BLANK,  
EACH MUST CONTAIN A  
NUMERIC CHARACTER 0 THRU 9.  
NOTES:  
C
1.  
REPRESENTS A CRITICAL DIMENSION  
2. CABLE CUT LENGTH:  
= (LENGTH: XXXX) - (SUBTRACTOR FOR END 1) - (SUBTRACTOR FOR END 2) + 12.0 MM*  
(SEE TABLE 1 FOR SUBTRACTORS)  
(* = ONLY APPLICABLE IF USING A SEMI-AUTOMATED COAXIAL CABLE STRIPPER TO PROVIDE A CLEAN CUT EDGE)  
3. ASSEMBLY TO BE 100% TESTED FOR OPENS & SHORTS  
4. ASSEMBLY TO BE 100% HI-POT TESTED PER TABLE 1  
C
C
5. AFTER FINAL ELECTRICAL TEST, LABEL EACH CABLE ASSEMBLY WITH 1 LABEL-ET  
6. CRITICALS ON CONNECTOR PRINTS TO BE CHECKED IN PROCESS.  
7. FINISHED ASSEMBLIES TO BE PACKAGED PER PACKAGING STANDARD CO-RF-WI-3040-M.  
LOCK WASHERS AND NUTS TO BE SHIPPED UNASSEMBLED. GASKETS TO BE INSTALLED ON CABLE.  
8. CABLE STOCKED IN INCHES, 1 INCH = 25.4 MILLIMETERS  
C
FIG 1  
9. S.I. TEST DATA IS PUBLISHED FOR LENGHTS OF 300MM AND 1000MM. TESTING OF OTHER  
SPECIFIC LENGTHS IS BY REQUEST.  
RFX6T-74SPX-74RPX-XXXX SHOWN  
10. MINIMUM BEND RADIUS FOR RG6 = 63.5 [2.75].  
CABLE STRIPPING DIMENSIONS  
PER END 1 AND END 2 ASSEMBLY PRINTS OR  
STRIPPED AND TINNED (SEE NOTES 11 -15, SHEET 2, FIG3)"  
11. FOR SING ENDED OR STRIPPED AND TINNED ASSEMBLIES: MAKE A DOUBLE ENDED  
ASSEMBLY AT TWICE THE CABLE LENGTH AND TEST BEFORE CUTTING ASSEMBLY IN HALF.  
12. DIM "A", "B", AND "C" HAVE A MINIMUM VALUE OF 0.0mm & A MAXIMUM VALUE OF 9.9mm.  
13. PRODUCTION OF STRIP AND TIN FOR CENTER DIELECTIC USE: A  
THIS PRODUCT MANUFACTURED  
Pb  
14. PRODUCTION OF STRIP AND TIN FOR SHIELD USE: D=A+B  
WITH LEAD-FREE PROCESSING  
F:\DWG\MISC\MKTG\RFX6T-XXXXX-XXXXXX-XXXX-MKT.SLDDRW  
15. PRODUCTION OF STRIP AND TIN FOR JACKET USE: E=A+B+C  
16. CONNECTORS TO BE ORIENTED ACCORDING TO CO-HD-WI-3048-M.  
17. FOR STRIPPED AND TINNED OPTION, ONLY THE CENTER CONDUCTOR IS TINNED.  
UNLESS OTHERWISE SPECIFIED,  
DIMENSIONS ARE IN  
MILLIMETERS [INCHES].  
TOLERANCES ARE:  
PROPRIETARY NOTE  
THIS DOCUMENT CONTAINS INFORMATION  
CONFIDENTIAL AND PROPRIETARY TO  
SAMTEC, INC. AND SHALL NOT BE REPRODUCED  
OR TRANSFERRED TO OTHER DOCUMENTS OR  
DISCLOSED TO OTHERS OR USED FOR ANY  
PURPOSE OTHER THAN THAT WHICH IT WAS  
OBTAINED WITHOUT THE EXPRESSED WRITTEN  
CONSENT OF SAMTEC, INC.  
DECIMALS  
ANGLES  
2
.X: 0.3 [.01]  
520 PARK EAST BLVD, NEW ALBANY, IN 47150  
PHONE: 812-944-6733 FAX: 812-948-5047  
e-Mail info@SAMTEC.com code 55322  
.XX: 0.13 [.005]  
.XXX: 0.051 [.0020]  
MATERIAL:  
SHEET SCALE: 2:1  
DO NOT SCALE DRAWING  
DESCRIPTION:  
SEE END 1 AND END 2 ASSEMBLY PRINTS  
TRUE 75 OHM, RF6T CABLE ASSEMBLY  
NO.  
DWGR. FX6T-XXXXX-XXXXXX-XXXX  
BY: R MUSSER  
03/27/2009  
SHEET 1 OF 3  
REVISION R  
-H4SP  
(STRAIGHT PLUG)  
-74SP  
(STRAIGHT PLUG)  
-74RP  
(USE DRAWING No. HDBNC-P-C-XX-ST-CA6  
FOR ASSEMBLY INSTRUCTIONS)  
(RIGHT ANGLE PLUG)  
(USE DRAWING No. BNC7T-P-C-XX-ST-CA6  
FOR ASSEMBLY INSTRUCTIONS)  
(USE DRAWING No. BNC7T-P-C-XX-RA-CA6  
FOR ASSEMBLY INSTRUCTIONS)  
PLATING  
2: 30μ" MIN. GOLD CENTER CONTACT  
100μ" MIN. NICKEL OUTER CONTACT  
100μ" MIN. NICKEL REMAINING METAL PARTS  
(END CONNECTOR P/N: HDBNC-P-C-HN-ST-CA6)  
3: 10μ" MIN. GOLD CENTER CONTACT  
100μ" MIN. NICKEL OUTER CONTACT  
100μ" MIN. NICKEL REMAINING METAL PARTS  
(END CONNECTOR P/N: HDBNC-P-C-GN-ST-CA6)  
PLATING  
PLATING  
3: 10μ" MIN. GOLD CENTER CONTACT  
4: 10μ" MIN. GOLD CENTER CONTACT  
3μ" MIN. GOLD OUTER CONTACT  
100μ" MIN. NICKEL REMAINING METAL PARTS  
(END CONNECTOR P/N: HDBNC-P-C-GF-ST-CA6)  
3: 10μ" MIN. GOLD CENTER CONTACT  
100μ" MIN. NICKEL OUTER CONTACT  
100μ" MIN. NICKEL REMAINING METAL PARTS  
(END CONNECTOR P/N: BNC7T-P-C-GN-RA-CA6)  
100μ" MIN. NICKEL OUTER CONTACT  
100μ" MIN. NICKEL REMAINING METAL PARTS  
(END CONNECTOR P/N: BNC7T-P-C-GN-ST-CA6)  
8: 30μ" MIN. GOLD CENTER CONTACT  
3μ" MIN. GOLD OUTER CONTACT  
100μ" MIN. NICKEL REMAINING METAL PARTS  
(END CONNECTOR P/N: HDBNC-P-C-HF-ST-CA6)  
NOTE: ALL CRITICAL DIMENSIONS ON BNC7T-P-C-XX-RA-CA6  
THAT APPLY MUST BE VERIFIED.  
NOTE: ALL CRITICAL DIMENSIONS ON BNC7T-P-C-XX-ST-CA6  
THAT APPLY MUST BE VERIFIED.  
NOTE: ALL CRITICAL DIMENSIONS ON HDBNC-P-C-XX-ST-CA6  
THAT APPLY MUST BE VERIFIED.  
-D4SP  
FIG 3  
(DIE CAST STRAIGHT PLUG)  
RFX6T-74SPX-102148-XXXX SHOWN  
(USE DRAWING No. BNC7T-P-C-XX-ST-CA6D  
FOR ASSEMBLY INSTRUCTIONS)  
PLATING  
3: 10μ" MIN. GOLD CENTER CONTACT  
100μ" MIN. NICKEL OUTER CONTACT  
100μ" MIN. NICKEL REMAINING METAL PARTS  
(END CONNECTOR P/N: BNC7T-P-C-GN-ST-CA6D)  
NOTE: ALL CRITICAL DIMENSIONS ON BNC7T-P-C-XX-ST-CA6D  
THAT APPLY MUST BE VERIFIED.  
F:\DWG\MISC\MKTG\RFX6T-XXXXX-XXXXXX-XXXX-MKT.SLDDRW  
PROPRIETARY NOTE  
THIS DOCUMENT CONTAINS INFORMATION  
CONFIDENTIAL AND PROPRIETARY TO  
SAMTEC, INC. AND SHALL NOT BE REPRODUCED  
OR TRANSFERRED TO OTHER DOCUMENTS OR  
DISCLOSED TO OTHERS OR USED FOR ANY  
PURPOSE OTHER THAN THAT WHICH IT WAS  
OBTAINED WITHOUT THE EXPRESSED WRITTEN  
CONSENT OF SAMTEC, INC.  
520 PARK EAST BLVD, NEW ALBANY, IN 47150  
PHONE: 812-944-6733 FAX: 812-948-5047  
e-Mail info@SAMTEC.com code 55322  
DESCRIPTION:  
DO NOT SCALE DRAWING  
SHEET SCALE: 1:1  
TRUE 75 OHM, RF6T CABLE ASSEMBLY  
DWG. NO.  
RFX6T-XXXXX-XXXXXX-XXXX  
SHEET 2 OF  
BY: R MUSSER 03/27/2009  
3
REVISION R  
-78SP  
-79SP  
-79RP  
(STRAIGHT PLUG)  
(STRAIGHT PLUG)  
(RIGHT ANGLE)  
(USE DRAWING No. DIN7A-PP-C-XX-ST-CA6  
FOR ASSEMBLY INSTRUCTIONS)  
(USE DRAWING No. MBNC7-P-C-XX-ST-CA6  
FOR ASSEMBLY INSTRUCTIONS)  
(USE DRAWING No. MBNC7-P-C-XX-RA-CA6  
FOR ASSEMBLY INSTRUCTIONS)  
PLATING  
PLATING  
PLATING  
2: 30μ" MIN. GOLD CENTER CONTACT  
100μ" MIN. NICKEL OUTER CONTACT  
100μ" MIN. NICKEL REMAINING METAL PARTS  
(END CONNECTOR P/N: MBNC7-P-C-HN-ST-CA6)  
2: 30μ" MIN. GOLD CENTER CONTACT  
100μ" MIN. NICKEL OUTER CONTACT  
100μ" MIN. NICKEL REMAINING METAL PARTS  
(END CONNECTOR P/N: MBNC7-P-C-HN-RA-CA6)  
4: 10μ" MIN. GOLD CENTER CONTACT  
3μ" MIN. GOLD OUTER CONTACT  
100μ" MIN. NICKEL REMAINING METAL PARTS  
(END CONNECTOR P/N: DIN7A-PP-C-GF-ST-CA6)  
3: 10μ" MIN. GOLD CENTER CONTACT  
3: 10μ" MIN. GOLD CENTER CONTACT  
5: 10μ" MIN. GOLD CENTER CONTACT  
100μ" MIN. NICKEL OUTER CONTACT  
100μ" MIN. NICKEL OUTER CONTACT  
10μ" MIN. GOLD OUTER CONTACT  
100μ" MIN. NICKEL REMAINING METAL PARTS  
(END CONNECTOR P/N: MBNC7-P-C-GN-ST-CA6)  
100μ" MIN. NICKEL REMAINING METAL PARTS  
(END CONNECTOR P/N: MBNC7-P-C-GN-RA-CA6)  
100μ" MIN. NICKEL REMAINING METAL PARTS  
(END CONNECTOR P/N: DIN7A-PP-C-GG-ST-CA6)  
6: 30μ" MIN. GOLD CENTER CONTACT  
30μ" MIN. GOLD OUTER CONTACT  
100μ" MIN. NICKEL REMAINING METAL PARTS  
(END CONNECTOR P/N: DIN7A-PP-C-HH-ST-CA6)  
NOTE: ALL CRITICAL DIMENSIONS ON MBNC7-P-C-XX-ST-CA6  
THAT APPLY MUST BE VERIFIED.  
NOTE: ALL CRITICAL DIMENSIONS ON MBNC7-P-C-XX-RA-CA6  
THAT APPLY MUST BE VERIFIED.  
NOTE: ALL CRITICAL DIMENSIONS ON DIN7A-PP-C-XX-ST-CA6  
THAT APPLY MUST BE VERIFIED.  
PROPRIETARY NOTE  
THIS DOCUMENT CONTAINS INFORMATION  
CONFIDENTIAL AND PROPRIETARY TO  
SAMTEC, INC. AND SHALL NOT BE REPRODUCED  
OR TRANSFERRED TO OTHER DOCUMENTS OR  
DISCLOSED TO OTHERS OR USED FOR ANY  
PURPOSE OTHER THAN THAT WHICH IT WAS  
OBTAINED WITHOUT THE EXPRESSED WRITTEN  
CONSENT OF SAMTEC, INC.  
520 PARK EAST BLVD, NEW ALBANY, IN 47150  
PHONE: 812-944-6733 FAX: 812-948-5047  
e-Mail info@SAMTEC.com code 55322  
DESCRIPTION:  
DO NOT SCALE DRAWING  
SHEET SCALE: 1:1  
TRUE 75 OHM, RF6T CABLE ASSEMBLY  
DWG. NO.  
RFX6T-XXXXX-XXXXXX-XXXX  
F:\DWG\MISC\MKTG\RFX6T-XXXXX-XXXXXX-XXXX-MKT.SLDDRW  
BY:R MUSSER  
03/27/2009 SHEET 3 OF 3  

相关型号：

SI9130DB

 5- and 3.3-V Step-Down Synchronous Converters

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9135LG-T1

 SMBus Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9135LG-T1-E3

 SMBus Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9135_11

 SMBus Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9136_11

 Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9130CG-T1-E3

 Pin-Programmable Dual Controller - Portable PCs

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9130LG-T1-E3

 Pin-Programmable Dual Controller - Portable PCs

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9130_11

 Pin-Programmable Dual Controller - Portable PCs

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9137

 Multi-Output, Sequence Selectable Power-Supply Controller for Mobile Applications

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9137DB

 Multi-Output, Sequence Selectable Power-Supply Controller for Mobile Applications

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9137LG

 Multi-Output, Sequence Selectable Power-Supply Controller for Mobile Applications

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9122E

 500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification Drivers

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明