SI-8205NHG_技术文档

SI-8205NHG

Application Note

Surface Mounted synchronized rectifier type Chopper Regulator IC

SI-8205NHG

November. 2014 Rev.3.0

SANKEN ELECTRIC CO., LTD.

SI-8205NHG

－－－ Contents －－－

1. General Description

1-1 Features

－－－－－－－－－－

3

1-2 Applications

1-3 Type

2. Specification

2-1 Package Information

2-2 Ratings

－－－－－－－－－－

4

5

7

2-3 Circuit Diagram

3. Terminal Description

3-1 Terminal List

3-2 Functional Description of Terminal

4. Operational Description

4-1 PWM Output Voltage Control

－－－－－－－－－－

8

－－－－－－－－－－

9

4-2 Overcurrent Protection / Thermal Shutdown －－－－－－－－－－ 10

5. Design Notes

5-1 External Components

5-2 Pattern Design Notes

5-3 Power Supply Stability

－－－－－－－－－－ 11

－－－－－－－－－－ 18

－－－－－－－－－－ 20

6. Applications

6-1 Soft Start

－－－－－－－－－－ 21

－－－－－－－－－－ 22

－－－－－－－－－－ 23

6-2 Output ON / OFF Control

6-3 Spike Noise Reduction

6-4 Reverse Bias Protection

6-5 External Synchronization

7. Terminology

－－－－－－－－－－ 24

2

SI-8205NHG

1. General Description

The SI-8205NHG is a synchronized rectifier type chopper regulator IC with a built-in power MOS. Due to

a current control system, it is applicable to such a super low ESR capacitor as a ceramic capacitor. It is

provided with various protection functions such as overcurrent protection, low input prohibition, overheat

protection etc. In order to protect the IC against in-rush current at start-up, the soft start function is provided.

The soft start time can be set by connecting external capacitors. In addition, the internal oscillator can be

operated in 300 kHz to 1MHz by external signals. This device is supplied in a compact and thin HOSP

8-pin package with heat slug on the back side.

●1-1 Features

-

Output current 3.0A

The output current of each output is maximum 3.0A in the HSOP 8-pin surface mounting

package.

-

High efficiency

Maximum efficiency 94%

Output voltage variable

0.5 - 24V

Low ESR capacitor for output

The ceramic capacitor can be used.

Operating frequency

Frequency fixed mode (SYNC pin = GND): 250kHz

External synchronization mode: 300kHz - 1MHz

Built-in functions for overcurrent and thermal shutdown

A current limiting type protection circuit against overcurrent and overheat is built in. (automatic

restoration type)

-

Soft start function (capable of ON/OFF output)

By adding an external capacitor, it is possible to delay the rise speed of the output voltage.

ON/OFF control of the output is also possible.

Small package (SI-8205NHG)

HSOP8 pin package with small heat slug

●1-2 Applications

For on-board local power supplies, power supplies for OA equipment, stabilization of secondary output

voltage of regulator and power supply for communication equipment.

●1-3 Type

-

Type: Semiconductor integrated circuits (monolithic IC)

3

SI-8205NHG

-

Structure: Resin molding type (transfer molding)

2. Specification

●2-1 Package Information

Unit: mm

*1 Type number

*2 Lot number (three digit)

1^stletter: The last digit of year

2^ndletter: Month

1 to 9 for Jan. to Sep.

O for Oct.

N for Nov.

PIN Assignment

1.GND

D for Dec.

3^rdand 4^thletter: week

2.EN/SS

3.VIN

4.SYNC

5.COMP

6.FB

*3 Control number (four digit)

7.BS

8.SW

External Terminal Processing: Sn-2.5Ag plating

4

SI-8205NHG

●2-2 Ratings

Table 1 Absolute Maximum Rating

Parameter

Symbol

Rating

46

Unit

V

Input Voltage VIN

V

IN

52

6

BS Pin voltage

V_BS

V_BS-SW

V_SW

V

BS Pin-SW Pin voltage

SW Pin voltage

46

6

FB Pin voltage

V_FB

6

EN/SS Pin voltage

V_EN/SS

V_FSET

6

FSET Pin voltage

6

COMP Pin voltage

V_COMP

Pd

V

Allowable Power Dissipation *1

1.35

150

W

°C

Tj

Junction Temperature

Storage Temperature

Thermal Resistance

Tstg

-40 to 150

θj-c

θj-a

40

74

°C /W

(Junction and Case) *2

Thermal Resistance

(Junction and Ambient) *2

*1: Since the thermal shutdown is provided, it may be operated at Tj >140°C.

*2: Glass epoxy board: 30.0mm × 30.0mm (copper foil area: 25.0mm × 25.0mm)

Table 2 Recommended Conditions

Parameter

DC Input Voltage

Output Current

Symbol

VIN

SI-8205NHG

7v to 43

Unit

*3

V

A

IO

0 to 3.0

-40 to ＋85

Temperature in Operation

Top

°C

*3: The minimum value of input voltage range is 7V or V_O+ 3V whichever higher.

In the case of V_IN= Vo +2 to Vo +3, IOUT=2A MAX

5

SI-8205NHG

Table 3 Electrical Characteristics

(Ta = 25°C, Vo = 5V, R1 = 9kΩ, R2 = 1kΩ)

Ratings

Parameter

Symbol

Unit

Test Condition

MIN

TYP

MAX

0.505

Setting Reference Voltage

VREF

0.495

0.500

V

VIN=14V, IO=1.0A

Output Voltage

Temperature Coefficient

Efficiency *4

Internal Operation

Frequency

⊿VREF/⊿

VIN=14V, IO=1.0A

Ta=-40°C to +85°C

±0.05

90

mV/°C

%

T

η

VIN=14V, Vo=5V, IO=1A

SYNC=GND

fo

250

kHz

Line Regulation *5

VLine

VLoad

50

mV

VIN=8 to 43V, Vo=5V, IO=1A

VIN=14V, Vo=5V,IO=0.1 to 3.0A ,

f=500kHz

Load Regulation *5

Overcurrent Protection

Start Current

IS

3.1

6.0

35

A

VIN=14V, Vo=5V

Circuit Current in

Non-operation 1

Circuit Current in

Non-operation 2

Flow-out

IIN

12

mA

uA

VIN= 14V, Vcomp=0V

VIN= 14V, VEN/SS= 0V

IIN(off)

Current

at Low Level

IEN/SS

5

μA

VEN/SS=0V, VIN= 12V

Voltage

EN/SS

terminal

Open-ciruit

Voltage

ON Threshold

Voltage

V

SSH

3.0

0.6

4.5

1.3

6.0

2.0

V

VIN=14V

V

C/EH

Ratings

Parameter

Symbol

Unit

Test Condition

MIN

-

TYP

MAX

Synchronous

Threshold

Voltage

Synchronizing

Frequency

1.85

VSYNC

FSYNC

-

V

VIN=14V, Vo=5V, IO=1A

SYNC

Terminal

300

151

1000

kHz VIN=14V, Vo=5V, IO=1A

°C

Thermal Shutdown Start

Tj

160

Temperature

Error Amplifier Voltage

Gain *5

Error Amplifier

Trans-conductance *5

Current Sense

Amplifier Conductance*5

Maximum ON Duty

Minimum ON Duty

High-side Switching

ON resistance *5

Low-side Switching

ON resistance *5

AEA

GEA

GCS

800

3.33

V/V

uA/V

A/V

DMAX

DMIN

RonH

90

150

%

nsec

mΩ

VIN=12V

RonL

150

mΩ

V

･I

O

VI^ON･IIN

*4: Efficiency should be calculated by using the following equation:

*5: This is a design assurance value.

η(%)=

×100

6

SI-8205NHG

●2-3 Circuit Diagram

2-3-1 Internal Equivalent Circuit

VIN

CUR_SNS

REG

ICSpwm

ICSocp

REG_DRV

REG

DRV_REG

S

N

S

I

REG_DRV

REG

BS

REG_BIAS STANDBY

STANDBY

OVC

H/S

Drv

BG

OCP_CMP

RegOK

M1

REG_UVLO

VinOK

VIN_UVLO

Level

Shift

CBoot

PWR_stage

M2

Vo

SW

n

REG

VinOK

REG

Level

Shift

REG

VinOK

LSon

L/S

Drv

Phase

GATE_logic

Set_PH

Forc_Off

Iramp

Phase_

logic

LSoff

OSC_RAMP

REG

STANDBY

g

l

f

e

f

h

FB

s

SYNC

REG

C

H

Res_PH

REG

CUR_COMP

VinOK

OVT

BS_CHG

PH_Open

REG

Forc_Off

OVT

BG

TSD

Set_PH

Control_logic

REG

RegOK

VinOK

INIT_OVP

OVP

OVP_CMP

REG_BIAS

P

M

O

REG

C

_

T

I

N

I

SS_Ref

f

G

REG

FB

EN_SS

EN/SS

Ref

SS_Ref

Err_AMP

STANDBY

REF

GND

COMP

Fig. 1

2-3-2 Typical Connection Diagram

C1:10μF/50V ×2

C2:22μF/16V ×2

C3:270pF

VIN

R5

C4

C4:0.1μF

3

7

Vo

L1

C5:1μF

VIN

2

BS

8

6

SW

FB

A ceramics capacitor should be a good

temperature character.

L1:10μH

EN/SS

C1

SI-8205NHG

C2

4

SYNC

GND

1

D1: SJPB-L6 (SANKEN)

COMP

GND

R1:9kΩ

(at Vo=5V)

R1

C5

5

R2:1kΩ

C3

R3:51kΩ

GND

R5:20Ω to 47Ω

D1

C6

R3

R2

Open

Fig. 2

7

SI-8205NHG

3. Terminal Description

●3-1 Terminal List

Table 4

Terminal

SI-8205NHG

Description

Symbol

GND

EN/SS

VIN

1

2

3

4

5

6

7

8

Ground Terminal

Soft Start Terminal (ON/OFF Terminal)

Input Terminal

SYNC

COMP

FB

External Synchronization Signal Input Terminal

Phase Compensation Terminal

Feedback Voltage Terminal

High side Boost Terminal

BS

Switching Output Terminal

SW

●3-2 Functional Description of Terminal

-

GND (terminal No. 1)

It is a ground terminal.

EN/SS (terminal No. 2)

-

It is a terminal for turning ON/OFF the IC. The soft start of output voltage can be made by connecting

a capacitor to this terminal also.

-

VIN (terminal No. 3)

It is an input voltage of IC.

SYNC (terminal No. 4)

This pin is intended to operate the internal oscillator by external signals.

COMP (terminal No. 5)

It is a phase compensation terminal for controlling the loop stably.

FB (terminal No. 6)

It is a terminal for setting the output voltage. The output voltage is set by R1 and R2.

BS (terminal No. 7)

It is an internal power supply for driving the gate of high side switch Nch - MOS. A capacitor of 10

nF or more is connected between the SW terminal and BS terminal to drive the high side Nch - MOS.

-

SW (terminal No. 8)

It is a switching output terminal which supplies power to the output.

8

SI-8205NHG

4. Operational Description

●4-1 PWM Output Voltage Control

The SI-8205NHG consists of two systems of feedback loops of current control and voltage control and

three blocks which compensate slope and, in the voltage control feedback, the output voltage is fed back

for PWM control loop and the SI-8205NHG is composed of an error amplifier which compares the division

of resistance with the reference voltage of 0.5V. The current control feedback is a loop which feeds back

the inductor current for PWM control and the inductor current shunted by using a sense MOS is detected

by a current sense amplifier. With respect to the slope compensation, in consideration of current control

system, in order to avoid the sub harmonic oscillation, slope compensation is made for the current control

slope. As shown in Fig.5, in the SI-8205NHG, by means of voltage control feedback, current control

feedback and calculation of slope compensation, the PWM control by current control system is made.

M1

BS_M

M2

Reference Voltage 0.5V

Fig.3 Current Control PWM Chopper Regulator Basic Configuration

Since the SI-8205NHG is a current control regulator, the COMP terminal voltage is proportional to the

peak value of the inductor current. When the ULVO is released or current of the EN/SS terminal exceeds

the threshold value, the switching operation is made. At first, switching operation is made by MIN ON duty

or MAX ON duty. The high side switch (hereinafter called as M1) is a switching MOS which supplies

power to the output and a switch for charging the BS capacitor (hereinafter called as BS M) charges the

capacitor C4 to drive M1.

At M1: ON, inductor current is increased by applying voltage to the SW switch and inductor, and the

output of the current detection amplifier which detects it also rises. The signal to which the output of this

current detection amplifier and the Ramp compensation signal are added is compared with the output of the

error amplifier by the current comparator (CUR COMP). When the added signal exceeds the output of the

error amplifier (COMP terminal voltage), the output of the current comparator becomes “H” to reset the RS

flip-flop. Then, M1 turns off and M2 turns on. Thereby, the regenerated current flows through M2 and the

external SBD (D1).

In the SI-8205NHG, the reset signal is generated at each cycle to reset the RS flip-flop. In the case the

9

SI-8205NHG

added signal does not exceed the COMP terminal voltage, the RS flip-flop is reset without fail by the signal

of the 10% OFF Duty circuit.

●4-2 Overcurrent Protection / Thermal Shutdown

過電流保護特性

6

5

4

V

As Vo drops, the oscillating frequency

3

2

is lowered.

1

0

1

2

3

4

5

6

出力電流ꢀI o[A]

Output Current IO [A]

Fig.4 Output Voltage Characteristics in Overcurrent

The SI-8205NHG incorporates a current limiting type overcurrent protection circuit. The overcurrent

protection circuit detects the peak current of a switching transistor and when the peak current exceeds the

set value, the ON time of the transistor is compulsorily shortened to limit the current by lowering the output

voltage. In addition, when the output voltage is lowered, the increase of current at low output voltage is

prevented by dropping the switching frequency. When the overcurrent condition is released, the output

voltage will be automatically restored.

Output Voltage

出力電圧

Restoration Setting

Temperature

Protection Setting Temperature

保護設定温度

復帰設定温度

接合温度

Junction Temperature

Fig.5 Output Voltage Characteristics in Thermal Shutdown

The thermal shutdown circuit detects the semiconductor junction temperature of the IC and when the

junction temperature exceeds the set value (around 150°C), the output transistor is stopped and the output is

turned OFF. When the junction temperature drops from the set value for overheat protection by around

10°C, the output transistor is automatically restored.

* Note for thermal shutdown characteristic

This circuit protects the IC against overheat resulting from the instantaneous short circuit, but it should be

noted that this function does not assure the operation including reliability in the state that overheat

continues due to long time short circuit.

10

SI-8205NHG

5. Cautions

●5-1 External Components

5-1-1 Choke coil L1

The choke coil L1 plays a main role in the chopper type switching regulator. In order to maintain the stable

operation of the regulator, such dangerous state of operation as saturation state and operation at high

temperature due to heat generation must be avoided.

The following points should be taken into consideration for the selection of the choke coil.

a) The choke coil should be fit for the switching regulator.

The coil for a noise filter should not be used because of large loss and generated heat.

b) For the peak detection current control, the inductance current may fluctuate at the cycle of integral

multiple of switching operation frequency.

Such phenomenon is called as sub harmonic oscillation and it may theoretically occur in the peak detection

current control mode.

Therefore, in order to assure stable operation, the inductance current is compensated inside the IC, and it is

required to select a proper inductance value to the output voltage.

Fig. 6 shows the selection range of the inductance L value to avoid the sub harmonic oscillation. The upper

limit of inductance L is variable subject to the input/output conditions, load current etc., therefore please

regard it as a reference in the Fig. 6 below.

Inductance L

Selectable area

Output Voltage Vo [V]

Fig. 6 Selection range of the inductance L value

11

SI-8205NHG

The pulse current of choke coil ΔIL and the peak current ILp are expressed by the following equation:

(Vin Vout)Vout

IL 

－－－(A)

LVin f

IL

2

ILp 

 Iout

－－－(B)

From this equation, you will see that as the inductance L of choke coil is decreased, ΔIL and ILP are

increased. In the event that the inductance is too little, the fluctuation of choke coil current is larger,

resulting in unstable operation of the regulator.

Care should be taken of decrease of inductance of choke coil due to magnetic saturation of overload, load

short circuit etc.

Low inductance

High inductance

Fig.7 Relation between Ripple current I_LPand Output Current I_O

c) The rated current shall be met.

The rated current of the choke coil must be higher than the maximum load current to be used. When the

load current exceeds the rated current of the coil, the inductance is sharply decreased to the extent that it

causes saturation state at last. Please note that overcurrent may flow since the high frequency impedance

becomes low.

d) Noise shall be low.

In the open magnetic circuit core which is of drum shape, since magnetic flux passes outside the coil, the

peripheral circuit may be damaged by noise. It is recommended to use the toroidal type, EI type or EE type

coil which has a closed magnetic circuit type core as much as possible.

5-1-2 Input Capacitor C1

The input capacitor is operated as a bypass capacitor of the input circuit to supply steep current to the

regulator during switching and to compensate the voltage drop of the input side. Therefore, the input

capacitor should be placed as close as to the regulator IC.

Even in the case that the rectifying capacitor of the AC rectifier circuit is located in the input circuit, the

input capacitor cannot play a role of the rectifying capacitor unless it is placed near the SI-8205NHG.

The selection of C1 shall be made in consideration of the following points:

12

SI-8205NHG

a) The requirement of withstand voltage shall be met.

b) The requirement of the allowable ripple voltage shall be met.

IIN

C1電流波形

VIN

1.VIN

Ip

ﾘｯﾌﾟﾙ電流

Ripple Current

0

Iv

C1

Ton

D 

T

Fig.8 Current Flow of C1

Fig. 9 Current Waveform of C1

The ripple current of the input capacitor

is increased in accordance with the

increase of the load current.

If the withstanding voltages or allowable ripple voltages are exceeded or used without derating, it is in

danger of causing not only the decreasing the capacitor lifetime (burst, capacitance decrease, equivalent

impedance increase, etc) but also the abnormal oscillations of regulator.

Therefore, the selection with sufficient margin is needed.

The effective value of ripple current flowing across the input capacitor can be obtained by the following

equation (2):

Vo

Irms 1.2

 Io －－(2)

Vin

For instance, where VIN=20V, Io=3A, Vo=5V

5

I r m1s.2 3  0.9A

20

Therefore, it is necessary to select the capacitor with the allowable ripple current of 0.9A or higher.

5-1-3 Output Capacitor C2

The current control system is a voltage control system to which a loop which detects and feeds back the

inductance current is added. By adding inductor current to the feedback loop, stable operation is realized

without taking into consideration the influence of secondary delay of the LC filter. Therefore, the

capacitance C of the LC filter which is required to compensate the secondary delay can be decreased and

furthermore, stable operation can be obtained, even if the low ESR capacitor (ceramic capacitor) is used.

The output capacitor C2 composes a LC low pass filter together with a choke coil L1 and functions as a

rectifying capacitor of switching output.

The current equivalent to the pulse current ΔIL of the choke coil current is charged and discharged in the

13

SI-8205NHG

output capacitor.

Therefore, it is necessary to meet the requirements of withstand voltage and allowable ripple current with

sufficient margin like the input capacitor.

IL

Vout

L1

C2電流波形

Io

Ripple current

ﾘｯﾌﾟﾙ電流

0

⊿IL

ESR

RL

The ripple current of the output capacitor is

equal to the ripple current of the choke coil and

does not vary even if the load current increases

Fig.11 C2 current curve

C2

Fig.10 C2 current flow

The ripple current effective value of the output capacitor is obtained by the equation (3).

IL

2 3

Irms 

－－－(3)

When ΔIL = 0.5A,

0.5

Irms 

≒0.14A

2 3

Therefore a capacitor having the allowable ripple current of 0.14A or higher is required.

In addition, the output ripple voltage Vrip of the regulator is determined by a product of the pulse current

ΔIL of the choke coil current (= C2 charging/discharging current) and the equivalent series resistance ESR

of the output capacitor.

Vrip  ILC2ESR

－－－(4)

It is therefore necessary to select a capacitor with low equivalent series resistance ESR in order to lower the

output ripple voltage. As for general electrolytic capacitors of same product series, the ESR shall be lower,

for the products of higher capacitance with same withstand voltage, or with higher withstand voltage

(almost proportional to larger externals) with same capacitance.

When ΔIL=0.5A, Vrip=40mV,

C2esr  40  0.5  80m

As shown above, a capacitor with the ESR of 80mΩ or lower should be selected. In addition, since the ESR

varies with temperature and increases at low temperature, it is required to examine the ESR at the actual

operating temperatures. It is recommended to contact capacitor manufacturers for the ESR value since it is

peculiar to capacitors.

14

SI-8205NHG

5-1-4 Flywheel Diode D1

The SI-8205NHG has a switch-over function between synchronous rectification and asynchronous one

subject to input/output conditions, load conditions etc.. Since asynchronous operation is made as well, it is

recommended to connect a fly wheel diode D1 externally.

The flywheel diode D1 is to discharge the energy which is stored in the choke coil at switching OFF.

For the flywheel diode, the Schottky barrier diode must be used. If a general rectifying diode or fast

recovery diode is used, the IC may be destroyed by applying reverse voltage due to the recovery and ON

voltage.

In addition, since the output voltage from the SW terminal (pin 8) of the SI-8205NHG series is almost

equivalent to the input voltage, the flywheel diode with the reverse withstand voltage of the input voltage or

higher should be used.

It is recommended not to use the ferrite bead for the flywheel diode.

5-1-5 Phase compensation elements C3, C6, R3

The stability and responsiveness of the loop are controlled through the COMP terminal.

The COMP terminal is an output of the internal trans-conductance amplifier.

The series combination of a capacitor and resistor sets the combination of pole and zero which determines

characteristics of the control system. The DC gain of voltage feedback loop can be calculated by the

following equation:

VFB

Adc  Rl Gcs AEA 

Vout

Here, VFB is feedback voltage (0.5V). AEA is the voltage gain of error amplifier, G_CStrans-inductance of

current detection and R1 a load resistance value. There are two important poles. One is produced by a

phase compensation capacitor (C3) and an output resistor of the error amplifier.

Another one is produced by a output capacitor and a load resistor. These poles appear at the following

frequencies:

GEA

fp1

2 C3 AEA

1

fp2 

2 C2 Rl

Here, G_EAis the trans-conductance of error amplifier. In this system, one zero is important. This zero is

produced by phase compensation capacitor C3 and phase compensation resistance R3. This zero appears in

the following frequencies:

1

fz1

2 C3 R3

If the output capacitor is large and/or ESR is large, this system may have another important zero. This zero

is produced by the ESR and capacitance of the output capacitor. And it exists in the following frequencies:

1

fESR 

2 C2 RESR

15

SI-8205NHG

In this case, the third pole which is set by the phase compensation capacitor (C6) and phase compensation

resistor (R3) is used to compensate the effect of ESR zero on the loop gain.

This pole exists in the following frequencies:

1

fp3 

2 C6 R3

The objective of design of phase compensation is to form the converter transfer function to obtain the

desired loop gain. The system crossover frequency where the feedback loop has a single gain is important.

The lower crossover frequency will produce the slower line and load transient. In the meantime, the higher

crossover frequency may cause instability of the system. The selection of the most suitable phase

compensation element is described below.

1. A phase compensation resistor (R3) is selected to set the resistor at the desired crossover frequency.

The calculation of R3 is made by the following equation:

2 C2 fc Vout 2 C20.1 fs Vout

R3 







GEAGCS VFB

GEAGCS

VFB

Here, fc is a desired crossover frequency. It should be one tenth or lower of the normal switching frequency

(fs).

2. In order to achieve the desired phase margin, a phase compensation capacitor (C3) is selected.

For the application having a representative inductance value, adequate phase margin is provided by setting

the zero compensation of one fourth or lower of the crossover frequency.

C3 is calculated by the following equation.

4

C3 

2  R3 fc

R3 is a phase compensation resistor.

3. It is required to judge whether the second compensation capacitor C6 is necessary or not.

It will be necessary, when the ESR zero of the output capacitor is located at a frequency which is lower

than the half of the switching frequency.

Namely, it is necessary, when the following equation is applicable.

1

fs



2 C2 RESR

2

In this case, the second compensation capacitor C6 is added and the frequency fp3 of ESR zero is set.

C6 is obtained from the following equation.

C2 RESR

C6 

R3

The constants for each output setting voltage in the case that ceramic capacitors or aluminum electrolytic

capacitors are used are shown in the following table.

The inductor L should be selected by reference to the choke coil L1 of 5-1-1. (Refer to Fig. 6 Scope of

16

SI-8205NHG

selection of inductance L value)

Table

5

fc=50kHz

fc=20kHz

Vout

[V]

L

Cout[uF]

Output

setting

R3

[kΩ]

12

C3

C6

R3

[kΩ]

4.7

7.3

13

C3

C6

[uH]

(ceramic capacitor)

[pF]

1000

680

330

220

100

[pF]

No

[pF]

6800

4700

3300

1800

680

[pF]

No

1.2

2.0 - 10

3.0 - 10

6.8 - 16

8.2 - 22

22 - 68

22 x 2

voltage (use

ceramic

1.8

3.3

5

18

33

capacitors)

51

20

12

124

47

fc=50kHz

fc=20kHz

R3

Cout [uF]/

Vout

[V]

L

ESR [mΩ]

R3

C3

C6

C3

C6

[uH]

(aluminum electrolytic capacitor)

[kΩ]

62

[pF]

220

180

100

[pF]

470

330

180

100

[kΩ]

24

[pF]

1.2

2.0 - 10

3.0 - 10

6.8 - 16

8.2 - 22

22 - 68

220/100

1500

1000

470

1000

680

330

220

100

1.8

3.3

5

91

36

160

240

620

68

100

240

330

12

150

Table 6 Output setting voltage (use aluminum electrolytic capacitors)

17

SI-8205NHG

●5-2 Pattern Design Notes

5-2-1 High Current Line

Since high current flows in the bold lines in the connection diagram, the pattern should be as wide and

short as possible.

V_IN

C4

3

7

V_O

L1

IN

BS

SW

FB

4

8

FEST

SYNC

SI-8205NHD

R1

SI-8205NHG

R4

C1

6

V_FB

2

SS/EN

C2

COMP

5

GND

R2

1

D1

C5

C3

I_ADJ

C6

OPEN

R3

GND

Fig. 12 Circuit Diagram

5-2-2 Input/ Output Capacitor

The input capacitor C1 and the output capacitor C2 should be placed to the IC as close as possible. If the

rectifying capacitor for AC rectifier circuit is on the input side, it can be used as an input capacitor.

However, if it is not close to the IC, the input capacitor should be connected in addition to the rectifying

capacitor. Since high current is discharged and charged through the leads of input/output capacitor at high

speed, the leads should be as short as possible. A similar care should be taken for the patterning of the

capacitor.

C1,C2

Fig. 13 Improper Pattern Example

Fig. 14 Proper Pattern Example

18

SI-8205NHG

5-2-3 FB Terminal (Output Voltage Set-up)

The FB terminal is a feedback detection terminal for controlling the output voltage. It is recommended to

connect it as close as possible to the output capacitor C2. When they are not close, the abnormal oscillation

may be caused due to the poor regulation and increase of switching ripple. The output voltage set-up is

achieved by connecting R1 and R2. I_FBshould be set to be around 0.5mA.

(The I_FBlower limit is 0.5mA, and the upper limit is not defined. However, it is necessary to consider that

the consumption current shall increase according to the I_FBvalue, resulting in lower efficiency.)

R1, R2 and output voltage are calculated from the following equations:

IFB=VFB/R2

*VFB=0.5v±1%

R1=(Vo-VFB) / IFB

R2＝VFB / IFB

Vout＝R1× (VFB/R2) ＋VFB

Fig. 15

-

R2 should be connected for the stable operation when set to Vo = 0.5V.

As to the relationship with the input/output voltage, it is recommended to set the ON width of SW

terminal to be 200 nsec or longer.

The wiring of COMP terminal, FB terminal, R1 and R2 that run parallel to the flywheel diode should be

avoided, because switching noise may interfere with the detection voltage to cause abnormal oscillation. It

is recommended to implement the wiring from the FB terminal to R2 as short as possible.

19

SI-8205NHG

-

Mounting Board Pattern Example

Surface Mounting Type (SI-8205NHG)

Fig. 16 Front side: materials on this side

Fig. 17 Back side: GND side

Fig. 18 Pattern Circuit Diagram

5-3 Power Supply Stability

The phase characteristics of the chopper type regulator are synthesized by the phase characteristics inside

the regulator IC and that of output capacitor Cout and the load resistor Rout. The phase characteristics

inside the regulator IC are generally determined by the delay time of the control block and the phase

characteristic of the output error amplifier. Among these two factors, the phase delay due to the delay time

of the control block rarely causes problems in actual use. Therefore, the phase characteristics of the error

amplifier are important. With respect to the compensation of phase characteristics of the output error

amplifier, external parts such as resistors and capacitors should be connected outside the IC for phase

compensation.

Please refer to phase compensation elements C3, C6 and R3 of 5-1-5.

20

SI-8205NHG

6. Applications

●6-1 Soft Start

When a capacitor is connected to terminal 2, the soft start is activated when the input voltage is applied.

Vout rises in relation with the charging voltage of Css. Therefore, the rough estimation is done by the time

constant calculation of Css charging.

The capacitor Css controls the rise time by controlling the OFF period of PWM control. The rise time tss

and the delay time t_delay are obtained approximately by the following equation:

It is the delay time t_delay when voltage of EN/SS terminal <1.6V.

It is the rise time tss when 1.6V< voltage of EN/SS <2.1V

t_delay = C_EN/SS× V_EN/SS-1/ I_EN/SS= 0.1μF × 1.6V / 5μA = 32msec

tss = C_EN/SS× (V_EN/SS-2– V_EN/SS-1) / I_EN/SS= 0.1μF × 0.5V / 5μA = 10msec

When not using the soft start function, the No.2 terminal should be open.

Fig. 19 Characteristic on Soft Start

Since the EN/SS terminal is pulled up (4.5V TYP) with the internal power supply of IC, the external

voltage can not be applied.

If there is no Css or it is extremely low, Vout rises at the time constants charging the output capacitor with

the output current restricted by the overcurrent protection Is.

Time constants at output capacitor start-up

t = (Co × Vo) / Is (at no load)

21

SI-8205NHG

*The amount of load current is deducted from the Is value at load.

●6-2 Output ON / OFF Control

The output ON-Off control is possible using the EN/SS terminal (No.2). The output is turned OFF when

the terminal 5 voltage falls below V_C/EH(1.6V TYP) by such as open collector. It is possible to use the soft

start together. Since the soft start terminal has been already pulled up (4.5V TYP), no voltage shall be

applied from the external side.

SI-8205NHG

2.EN/SS

Fig. 20 ON / OFF Control 1

Fig. 21 ON / OFF Control 2

●6-3 Spike Noise Reduction

In order to reduce the spike noise, it is possible to compensate the output waveform of the SI-8205NHG

and the recovery time of the diode by a capacitor (snubber), but it should be noted that the efficiency is also

slightly reduced.

8.SW

3.VIN

SI-8205NHG

1.GND

Around 10Ω

Around 1000pF

Fig. 22 Example of Snubber

22

SI-8205NHG

* When the spike noise is observed with an oscilloscope, the lead wire may function as an antenna and the

spike noise may be observed extremely higher than usual if the probe GND lead wire is too long. In the

observation of spike noise, the probe lead wire should be as short as possible and be connected with the

root of the output capacitor.

●6-4 Reverse Bias Protection

A diode for reverse bias protection will be required between input and output when the output voltage is

higher than the input terminal voltage, such as in battery chargers.

3PIN

8PIN

SI-8205NHD

SI-8205NHG

Fig. 23 Diode for Reverse Bias Protection

●6-5 External synchronization

When the external signal is input (300kHz (TYP) to 1MHz (TYP)) to the 4th pin, operation can be

performed at a frequency in synchronization with external signals. Fig.24 shows the operating waveform in

synchronization with external signals. In addition, the operation is performed at a fixed frequency 250kHz

by connecting the 4th pin to GND.

Condition

External synchronization 500 kHz (2 μsec/ div)

External synchronization 1 MHz (1 μsec/ div)

SYNC terminal (external input: 500 kHz)

SYNC terminal (external input: 1 MHz)

SW terminal (operation frequency)

Fig.24 External synchronization operation

23

SI-8205NHG

7. Terminology

-

Jitter

It is a kind of abnormal switching operations and is a phenomenon that the switching pulse width varies in

spite of the constant condition of input and output. The output ripple voltage peak width is increased when

a jitter occurs.

-

Recommended Conditions

It shows the operation conditions required for maintaining normal circuit functions. It is required to meet

the conditions in actual operations.

-

Absolute Maximum Ratings

It shows the destruction limits. It is required to take care so that even one item does not exceed the

specified value for a moment during instantaneous or normal operation.

-

Electrical Characteristics

It is the specified characteristic value in the operation under the conditions shown in each item. If the

operating conditions are different, it may be out of the specifications.

-

PWM (Pulse Width Modulation)

It is a kind of pulse modulation systems. The modulation is achieved by changing the pulse width in

accordance with the variation of modulation signal waveform (the output voltage for chopper type

switching regulator).

-

ESR (Equivalent Series Resistance)

It is the equivalent series resistance of a capacitor. It acts in a similar manner to the resistor

series-connected to the capacitor.

24

SI-8205NHG

Notice

・The contents of this description are subject to change without prior notice for improvement etc. Please

make sure that any information to be used is the latest one.

・Any example of operation or circuitry described in this application note is only for reference, and we are

not liable to any infringement of industrial property rights, intellectual property rights or any other rights

owned by third parties resulting from such examples.

・In the event that you use any product described here in combination with other products, please review the

feasibility of combination at your responsibility.

・Although we endeavor to improve the quality and reliability of our product, in the case of semi-conductor

components, defects or failures which occur at a certain rate of probability are inevitable.

The user should take into adequate consideration the safety design in the equipment or the system in order to

prevent accidents causing death or injury, fires, social harms etc..

・Products described here are designed to be used in the general-purpose electronic equipment (home

appliances, office equipment, communication terminals, measuring equipment etc.).

If used in the equipment or system requiring super-high reliability (transport machinery and its control

equipment, traffic signal control equipment, disaster/crime prevention system, various safety apparatus etc.),

please consult with our sales office. Please do not use our product for the equipment requiring ultrahigh

reliability (aerospace equipment, atomic control, medical equipment for life support etc.) without our written

consent.

・The products described here are not of radiation proof type.

・The contents of this brochure shall not be transcribed nor copied without our written consent.

25


型号：	SI-8205NHG
厂家：	SANKEN ELECTRIC
描述：	Switching Regulator 开关
文件：	总25页 (文件大小：710K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

SI-8205NHG [SANKEN]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB

SI9137LG

SI9122E