LA4592W [SANYO]
1.5-V Preamplifier + Power Amplifier for Headphone Stereo Products; 1.5 -V前置放大器+功率放大器立体声耳机产品型号: | LA4592W |
厂家: | SANYO SEMICON DEVICE |
描述: | 1.5-V Preamplifier + Power Amplifier for Headphone Stereo Products |
文件: | 总5页 (文件大小:164K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Ordering number : EN5662
Monolithic Linear IC
LA4592W
1.5-V Preamplifier + Power Amplifier
for Headphone Stereo Products
functions.
• Ripple filter
Overview
The LA4592W is a single-chip 1.5-V headphone stereo
system IC. The LA4592W adds a variety of functions,
including a switch amplifier (for end product audio quality
switches, the metal tape switch, and other switches) and an
AMSS (Automatic Music Search System) function that
supports blank skipping, to the earlier LA4590W.
Furthermore, the LA4592W provides even lower no-signal
time power levels for lower end-product power
dissipation. In combination with the LA3235W 1.5-V
record preamplifier IC, the LA4592W can be used to
implement a record/playback cassette system with just two
ICs.
• Low boost function (BTL operation in the low-
frequency region)
• Inter-track detection function (Supports AMSS and
blank skipping)
• Two switching amplifiers
• Power switch (standby function)
Features
• Virtual ground impedance is reduced by built-in V
amplifier
REF
• No capacitor required for ripple filter oscillation
prevention.
• Provides ample output power at low frequencies.
Functions
• Stereo preamplifier: supports auto reverse and includes a
muting function.
(P = 24 mW, V = 1.2 V, f = 150 Hz)
O
CC
• High-frequency cutoff capacitors built into the
preamplifier and power amplifier inputs to minimize
buzzing.
• Stereo power amplifier: Includes OCL and muting
Package Dimensions
unit: mm
3163A-SQFP48
[LA4592W]
Ambient temperature, Ta – °C
SANYO: SQFP48
Specifications
Maximum Ratings at Ta = 25°C
Parameter
Maximum supply voltage
Symbol
Conditions
Ratings
3.0
Unit
V
V
CC max
Pd max
Topr
Allowable power dissipation
Operating temperature
Storage temperature
320
–10 to +60
–40 to +125
mW
°C
Tstg
°C
Allowable Operating Ranges at Ta = 25°C
Parameter
Recommended supply voltage
Operating supply voltage range
Symbol
VCC
Conditions
Ratings
1.5
Unit
V
VCCop
0.95 to 2.2
V
SANYO Electric Co.,Ltd. Semiconductor Bussiness Headquarters
TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110 JAPAN
73097HA (OT) No. 5662-1/5
LA4592W
Operating Characteristics at Ta = 25°C, V = 1.2 V, f = 1 kHz, 0.775 V = 0 dB, R = 10 kΩ (preamplifier)
CC
L
RL = 16 Ω (power amplifier)
Ratings
typ
Parameter
Symbol
Conditions
Unit
min
max
16
[PRE + PWR]
I
CCO1
Rg = 2.2 kΩ, RV = 0 Ω
With the power switch off
VO = –20 dBm, RV = 10 kΩ
8.5
54
11
0.1
57
mA
µA
dB
Quiescent current
ICCO2
5
60
Voltage gain (closed loop)
[PRE AMP]
VGT
Voltage gain (open loop)
Voltage gain (closed loop)
Maximum output voltage
Total harmonic distortion
Equivalent input noise voltage
Interchannel crosstalk
F/R crosstalk
VG0
VG1
VO = –20dBm
VO = –20dBm
60
34
100
68
35.3
210
0.08
1.3
dB
dB
mV
%
µV
dB
dB
37
VO max1 THD = 1 %
THD1
VN1
CT1
CT2
VG = 35.3 dB/NAB, VO = 100 mV
0.5
3.0
Rg = 2.2 kΩ, BPF = 20 Hz to 20 kHz
Rg = 2.2 kΩ, TUNE 1 kHz, VO = –20 dBm
Rg = 2.2 kΩ, TUNE 1 kHz, VO = –20 dBm
45
65
56
78
Rg = 2.2 kΩ, Vr = –30 dBm,
fr = 100 Hz, TUNE 100 Hz
Ripple rejection ratio
Rr1
45
52
dB
VIN = –40 dBm, TUNR 1 kHz,
With the muting function on
Muting output voltage
VM1
–90
dBm
[Low Boost + Power Amplifier]
VG3
VG4
VG5
VG6
PO1
PO2
THD2
CT3
VNO
VO = –20 dBm
20.5
20.5
24.5
28
5
13
23
23
27.5
32
9
19
0.3
43
20
25.5
25.5
30.5
36
dB
dB
dB
dB
mW
mW
%
VO = –20 dBm, L.B = ON
VO = –20 dBm, L.B = ON, f = 10 kHz
VO = –20 dBm, L.B = ON, f = 100 Hz
THD = 10 %
THD = 10 %, f = 100 Hz, L.B = ON
PO = 1 mW
Voltage gain (closed loop)
Output voltage
Total harmonic distortion
Interchannel crosstalk
Output noise voltage
1.5
33
VO = –20 dBm, RV = 0 Ω
RV = 0 Ω, BPF = 20 Hz to 20 kHz
38
dB
µV
RV = 0 Ω, Vr = –30 dBm,
Ripple rejection ratio
Muting output voltage
Rr2
50
74
dB
fr = 100 Hz, TUNE 100 Hz
VIN = –30 dBm, TUNE 1 kHz,
With the muting function on
VM2
–90
dBm
Input resistance
Voltage gain difference
[Ripple Filter]
Ri
∆VG3
8
10
0
12
1.5
kΩ
dB
fr = 100 Hz, Vr = –30 dBm, VCC = 1.0 V,
IRF = 25 mA, using a rank 6 2SB1295
Ripple rejection ratio
Rr3
33
39
dB
V
Output voltage
[AMSS]
VRF
VCC = 1.0 V, IRF = 25 mA
0.89
3.33
479
0.94
The preamplifier output voltage
OAMSS1 when the AMSS VO = 0.6 V p-o
With the PWR muting on. (AMSS)
Operating output voltage
Operating output voltage
V
V
4.7
6.64
mV
µV
The preamplifier output voltage
OAMSS2 when the AMSS VO = 0.6 V p-o
With the PWR muting off. (BLANK SKIP)
675
953
The preamplifier output voltage
when the AMSS VO = 0.6 V p-o
Operating output voltage
Operating output voltage
V
V
OAMSS3
2.62
375
3.7
5.23
mV
µV
With pin 34 shorted through a 270-Ω resistor.
With the PWR muting on.
The preamplifier output voltage
when the AMSS VO = 0.6 V p-o
OAMSS4
530
749
With pin 34 shorted through a 270-Ω resistor.
With the PWR muting on.
[SW AMP]
Voltage gain (closed loop)
Maximum output voltage
VG7
VO = –25 dBm
–1.2
25
–0.7
60
–0.2
dB
mV
VO max2 THD = 1 %
With the input pins open, Vr = –30 dBm,
fr = 100 Hz, TUNE 100 Hz
Ripple rejection ratio
Rr4
50
75
dB
Output voltage when off
VM3
VIN = –20 dBm, TUNE 1 kHz, SW OFF
–90
dBm
No. 5662-2/5
LA4592W
AMSS Temperature Characteristics (Values for reference only)
Ratings
typ
Parameter
Symbol
Ta
Conditions
Unit
°C
min
–10
max
50
AMSS
25
The preamplifier output voltage
VOAMSS1 when the AMSS VO = 0.6 V p-o
With the PWR muting on. (AMSS)
3.9
4.7
5.4
mV
µV
Operating output voltage
The preamplifier output voltage
VOAMSS2 when the AMSS VO = 0.6 V p-o
605
675
735
Block Diagram
No. 5662-3/5
LA4592W
Test Circuit Diagram
No. 5662-4/5
LA4592W
Sample Application Circuit
*: Adjust the values of the capacitors marked with an asterisk to match the timing required by the end product.
■ No products described or contained herein are intended for use in surgical implants, life-support systems, aerospace
equipment, nuclear power control systems, vehicles, disaster/crime-prevention equipment and the like, the failure of
which may directly or indirectly cause injury, death or property loss.
■ Anyone purchasing any products described or contained herein for an above-mentioned use shall:
➀ Accept full responsibility and indemnify and defend SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and
distributors and all their officers and employees, jointly and severally, against any and all claims and litigation and all
damages, cost and expenses associated with such use:
➁ Not impose any responsibility for any fault or negligence which may be cited in any such claim or litigation on
SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors or any of their officers and employees
jointly or severally.
■ Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for
volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied
regarding its use or any infringements of intellectual property rights or other rights of third parties.
This catalog provides information as of July, 1997. Specifications and information herein are subject to change
without notice.
No. 5662-5/5
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明