LA7852 [SANYO]
CRT Display Synchronization Deflection Circuit; CRT显示器同步偏转电路型号: | LA7852 |
厂家: | SANYO SEMICON DEVICE |
描述: | CRT Display Synchronization Deflection Circuit |
文件: | 总5页 (文件大小:84K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Ordering number: EN2781B
Monolithic Linear IC
LA7852
CRT Display Synchronization Deflection Circuit
Overview
Package Dimensions
unit : mm
The LA7852 is a sync-deflection circuit IC dedicated to CRT
display use. It can be connected to the LA7832/7833, 7837/
7838 (for vertical output use) to form a sync-deflection circuit
that meets every requirement for CRT display use.
3059-DIP22S
[LA7852]
So far, ICs for color TV use have been applied to the sync-
deflection circuit for CRT display use, and general-purpose ICs
such as one-shot multivibrator, inverter and a lot of transistors
have been used to form the peripherals such as sync input
interface, horizontal phase shifter. The LA7852 contains these
peripherals on chip and adopts a stable circuit for horizontal
oscillation from 15 kHz to 100 kHz aiming at improving the
characteristics required for CRT display use.
The LA7852 has independent GND pins for the horizontal
block and vertical block, thus facilitating pattern layout for
applications where the LA7852 is used at high frequencies.
SANYO : DIP22S
Features
.
.
The vertical pull-in range is approximately 10 Hz at
fv = 60 Hz.
The horizontal oscillation frequency can be adjusted stably
from 15 kHz to 100 kHz.
The horizontal display can be shifted right/left.
The horizontal/vertical sync input can be used intact
regardless of the difference in pulse polarity and pulse width.
The AFC feedback sawtooth wave can be obtained by
simply applying a flyback pulse to the IC as a trigger pulse.
Any duty of the horizontal pulse can be set.
Good vertical linearity because DC bias at vertical output
stage is subjected to sampling control within retrace time.
Excellent interlace and vertical jitter characteristics on the
high-definition display because of independent GND pins for
the horizontal block and vertical block.
Pd max – Ta
.
.
.
.
.
.
Ambient temperature, Ta – °C
Built-in Functions
[Horizontal Block]
[Vertical Block]
.
.
.
AFC
Horizontal OSC
X-ray protector
Horizontal phase shift
AFC sawtooth wave generator
Horizontal pulse duty setting
Vertical OSC
Vertical sawtooth wave generator
Sampling type DC voltage control
.
.
.
.
.
.
SANYO Electric Co.,Ltd. Semiconductor Bussiness Headquarters
TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110 JAPAN
81096HA(II)/9138YT/8228YT,TS No.2781-1/5
LA7852
Specifications
Maximum Ratings at Ta = 25°C
Parameter
Maximum supply voltage
Allowable power dissipation
Operating temperature
Symbol
, V
Conditions
Ratings
14
Unit
V
V
11 22
Pd max
Topr
Ta % 65° C
780
–20 to +85
–55 to +125
mW
°C
Storage temperature
Tstg
°C
Operating Conditions at Ta = 25°C
Parameter
Symbol
Conditions
Ratings
12
Unit
V
Recommended supply voltage
V , V
11 22
Operating voltage range
V
, V
11 22
9 to 13.5
5
V
Recommended vertical pulse input peak value
Operating vertical pulse input peak value range
Recommended horizontal pulse input peak value
Operating horizontal pulse input peak value range
V
V
H
H
Vp-p
Vp-p
Vp-p
Vp-p
PULSE
PULSE
PULSE
PULSE
2 to 6
5
2 to 6
Operating Characteristics at Ta = 25°C, V11, V22 = 12 V
Parameter
Symbol
Conditions
min
typ
max
Unit
V
V
current dissipation
current dissipation
I
12
5
30 mA
12 mA
CC11
11
22
I
CC22
Vertical frequency pull-in range
Vertical free-running frequency
Vp
Vertical sync 60 Hz
fv center 55 Hz
10.0
50
12.0
Hz
Hz
IN
fv
60
Increased/reduced voltage
characteristic of vertical
frequency
∆fv-v
V
= 12 ± 1 V, 55 Hz at 12 V
–0.1
3.8
+0.1
Hz
22
Midpoint control
threshold level
4.4
4.0
V
V
Vertical OSC start voltage
Fvcst
Temperature characteristic of
vertical frequency
Ta = –10 to +60°C
–0.028
12
+0.028 Hz/°C
18 dB
Vertical driver
amplification factor
Gv
I
+
0.85
–1.6
1.6 mA
AFC
Horizontal AFC DC loop gain
I
–
–0.85 mA
AFC
Horizontal free-running
frequency
f
f
center 15.734 kHz
H
–750
+750
4.0
Hz
V
H
Horizontal OSC start voltage
f cst
H
Increased/reduced voltage
characteristic of horizontal
frequency
∆f cv
V
= 12 ± 1 V, 15.734 kHz at 12 V
–50
+50
+50
Hz
Hz
H
11
Horizontal OSC warm-up drift
∆f
5 s to 30 min. after application of power
Ta = –10 to +60°C
–50
–2.9
6.0
H
Temperature characteristic of
horizontal frequency
+2.9 Hz/°C
12.0 mA
Horizontal output drive current
I
13
Increased/reduced voltage
characteristic of phase shifter
delay time
V
= 12 ± 1 V
–0.5
–0.1
–1.0
+0.5 %/V
+0.1 %/°C
+1.0 %/V
+0.13 %/°C
11
Temperature characteristic of
phase shifter delay time
Ta = –10 to +60°C
Increased/reduced voltage
characteristic of phase shifter
delay time
V
= 12 ± 1 V
11
Temperature characteristic of
phase shifter pulse width
Ta = –10 to +60°C
–0.13
9.9
AFC phase comparison center
time
15.734 kHz after FBP input
11.5
µs
No.2781-2/5
LA7852
Parameter
Symbol
Conditions
min
typ
max
+1.5
Unit
%/V
Increased/reduced voltage
characteristic of AFC phase
comparison center time
V
= 12 ± 1 V
–1.5
11
Temperature characteristic of
AFC phase comparison center
time
Ta = –10 to +60°C
–0.2
+0.2
%/°C
Comparison waveform
generating
input operation voltage
V
0.6
0.5
0.9
0.8
V
V
5
Pin 14 voltage at hold-down
operation start
V
14
Equivalent Circuit Block Diagram
No.2781-3/5
LA7852
Sample Application Circuit
(Note)
Co is connected when
oscillation occurs in vertical
output in Sample Application
Circuit.
( ): Negative pulse
mode
VR2 is fixed after adjustment.
(Note) For the LA7853, the vertical pull-in range is
20 Hz at vertical sync 60 Hz.
Unit (resistance: Ω, capacitance: F)
No.2781-4/5
LA7852
Sample Application Circuit
( ): Negative pulse mode
VR2 is fixed after adjustment
A05903
Package
DIP-20S
DIP-20S
DIP-22S
DIP-22S
(Slim Type)
(Slim Type)
(Shrink Type)
(Shrink Type)
Differences in
characteristics
Vertical
pull-in range
(fv = 60 Hz)
10 Hz
20 Hz
10 Hz
20 Hz
Ground pin
Horizontal/vertical
common
horizontal/vertical
common
Horizontal/vertical
separated
Horizontal/vertical
separated
No products described or contained herein are intended for use in surgical implants, life-support systems, aerospace equipment,
nuclear power control systems, vehicles, disaster/crime-prevention equipment and the like, the failure of which may directly or
indirectly cause injury, death or property loss.
Anyone purchasing any products described or contained herein for an above-mentioned use shall:
1 Accept full responsibility and indemnify and defend SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors
and all their officers and employees, jointly and severally, against any and all claims and litigation and all damages, cost and
expenses associated with such use:
2 Not impose any responsibility for any fault or negligence which may be cited in any such claim or litigation on SANYO
ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors or any of their officers and employees jointly or severally.
Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume
production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use
or any infringements of intellectual property rights or other rights of third parties.
This catalog provides information as of August, 1996. Specifications and information herein are subject to change without notice.
No.2781-5/5
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明