概述
数据手册X1G005601019401 概述
CMOS Output Clock Oscillator,
X1G005601019401 数据手册
通过下载X1G005601019401数据手册来全面了解它。这个PDF文档包含了所有必要的细节，如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载Programmable Clock OSC
SG-8018CG
SG-8018CG 21.606000 MHz TJHSA
Product name
Product Number / Ordering code
X1G0056010194xx
Please refer to the 8.Packing information about xx (last 2 digits)
Output waveform CMOS
Pb free / Complies with EU RoHS directive
Reference weight Typ.
13 mg
1.Absolute maximum ratings
Parameter
Symbol
VCC-GND
Min.
-0.3
Typ.
-
Max.
+4.0
Unit
V
Conditions / Remarks
-
Maximum supply voltage
Stored as bare product after
unpacking
ST or OE terminal
Storage temperature
Input voltage
T_stg
VIN
-40
-
-
+125
ºC
V
GND-0.5
Vcc+0.3
2.Specifications(characteristics)
Parameter
Output frequency
Symbol
fo
VCC
Min.
Typ.
21.606000
Max.
Unit
MHz
V
Conditions / Remarks
Supply voltage
Typ. 1.8V / 2.5V / 3.3V
-
1.62
-
-
-
-
-
-
-
-
-
-
-
-
3.63
Operating temperature
Frequency tolerance
Current consumption
Stand-by current
Disable current
Symmetry
T_use
f_tol
ICC
-40
+105
ºC
x10-6
mA
µA
mA
%
T_use : -40 to +105℃
-50
+50
Vcc=3.3V Typ., No load
-
4.4
Vcc=3.3V Typ., ST=GND
I_std
I_dis
SYM
VOH
-
2.5
-
-
-
50%Vcc, L_CMOS=<15pF
45
55
Output voltage
-
90%Vcc
-
10%Vcc
15
V
VOL
-
-
V
Output load condition
Input voltage
CMOS Load
ST Terminal
ST Terminal
L_CMOS
VIH
-
pF
V
70%Vcc
-
-
VIL
30%Vcc
V
Rise time
20% to 80%Vcc,L_CMOS=15pF
20% to 80%Vcc,L_CMOS=15pF
tr
-
-
-
-
-
-
-
-
-
-
6
6
1
-
ns
ns
μs
μs
ms
Fall time
tf
Measured from the time OE or
ST pin crosses 30%Vcc
Disable time
Enable time
Resum time
t_stp
t_sta
t_res
-
Measured from the time STpin
crosses 70%Vcc
3
Measured from the time Vcc
reaches its rated minimum value,
1.62V
Included in Frequency tolerance
10 years
Start-up time
t_str
-
-
-
-
3
-
ms
x10-6/Year
Frequency aging
f_aging
1 Page
3.Timing chart
tr
tf
VCC
80 %VCC
50 %VCC
20 %VCC
GND
tw
t
4.Test circuit
1) Waveform observation
2) Current consumption
* Current consumption under the disable function should be OE = GND
Current consumption under the standby function should be ST = GND.
3) Measurement conditions
(1) L_CMOS includes probe capacitance.
(2) Mount a by-pass capacitor (approx. 0.01 to 0.1 µF) near the mains terminals
of the oscillator (between Vcc and GND)
2 Page
5.External dimensions
(Unit: mm)
6.Footprint(Recommended)
(Unit: mm)
In order to achieve optimum jitter performance,
the 0.1 μF capacitor between VCC and GND
should be placed. It is also recommended that
the capacitors are placed on the device side of
the PCB, as close to the device as possible and
connected together with short wiring pattern.
OE Pin = "H" : Specified frequency output.
OE Pin = "L" : Output is low level (weak pull - down)
ST Pin = "H" : Specified frequency output.
ST Pin = "L" : Output is low level (weak pull - down),
oscillation stops.
7.Reflow profile
Reflow condition (Follow of JEDEC STD-020D.1)
Temperature [ ºC]
300
TP:
TL:
+260ºC OVER
+255ºC
tp: at least 30 s
250
200
150
100
50
Ramp-up rate
+3 ºC/s Max.
Ramp-down rate
-6 ºC/s Max.
tL
+217ºC
Ts max: +200ºC
60 s to 150 s
( +217 ºC over )
ts
Ts min:
+150 ºC
60 s to 120 s
( +150ºC to +200ºC)
Time: +25 ºC to Peak
0
60
120
180
240
300
360
420
480
540
600
660
720
780
Time [ s ]
8.Packing information
[ 1 ]Product number last 2 digits code(xx) description
The recommended code is "00"
X1G0056010194xx
Condition
Condition
1000pcs / Reel
2000pcs / Reel
3000pcs / Reel
Code
01
Code
Any Q'ty vinyl bag(Tape cut)
Any Q'ty / Reel
14
15
00
11
12
250pcs / Reel
3 Page
[ 2 ] Taping specification
Subject to EIA-481 & IEC-60286
(1) Tape dimensions
ꢀꢀꢀMaterial of the Carrier Tape : PS
ꢀꢀꢀMaterial of the Top Tape : PET
Unit: mm
A
B
User direction of feed
Carrier tape
Top tape
F
C
Symbol
Value
A
B
C
D
E
F
Φ1.5
4.0
4.0
5.25
8.0
1.15
(2) Reel dimensions
Material of the Reel : PS
11.4±1.0
9±0.3
Φ180+0-3.0
2±0.5
Φ13±0.2
6-R0.5
Φ10
Φ21±0.8
Form and Size of reel window shows are one of the example
4 Page
9.Notice
NOTICE：PLEASE READ CAREFULLY BELOW BEFORE THE USE OF THIS DOCUMENT ©Seiko Epson Corporation 2020
1. The content of this document is subject to change without notice. ꢀBefore purchasing or using Epson products, please contact with sales
representative of Seiko Epson Corporation (“Epson”) for the latest information and be always sure to check the latest information
published on Epson’s official web sites and resources.
2. This document may not be copied, reproduced, or used for any other purposes, in whole or in part, without Epson’s prior consent.
3. Information provided in this document including, but not limited to application circuits, programs and usage, is for reference purpose only.
Epson makes no guarantees against any infringements or damages to any third parties’ intellectual property rights or any other rights
resulting from the information. This document does not grant you any licenses, any intellectual property rights or any other rights with
respect to Epson products owned by Epson or any third parties.
4. Using Epson products, you shall be responsible for safe design in your products; that is, your hardware, software, and/or systems shall be
designed enough to prevent any critical harm or damages to life, health or property, even if any malfunction or failure might be caused by
Epson products. In designing your products with Epson products, please be sure to check and comply with the latest information
regarding Epson products (including, but not limited to this document, specifications, data sheets, manuals, and Epson’s web site).
Using technical contents such as product data, graphic and chart, and technical information, including programs, algorithms and
application circuit examples under this document, you shall evaluate your products thoroughly both in stand-alone basis and within your
overall systems. You shall be solely responsible for deciding whether to adopt/use Epson products with your products.
5. Epson has prepared this document carefully to be accurate and dependable, but Epson does not guarantee that the information is always
accurate and complete. Epson assumes no responsibility for any damages you incurred due to any misinformation in this document.
6. No dismantling, analysis, reverse engineering, modification, alteration, adaptation, reproduction, etc., of Epson products is allowed.
7. Epson products have been designed, developed and manufactured to be used in general electronic applications and specifically
requires particular quality or extremely high reliability in order to refrain from causing any malfunction or failure leading to critical harm to
life and health, serious property damage, or severe impact on society, including, but not limited to listed below (“Specific Purpose”).
Therefore, you are strongly advised to use Epson products only for the Anticipated Purpose.ꢀ Should you desire to purchase and use
Epson products for Specific Purpose, Epson makes no warranty and disclaims with respect to Epson products, whether express or
implied, including without limitation any implied warranty of merchantability or fitness for any Specific Purpose. Please be sure to
contact our sales representative in advance, if you desire Epson products for Specific Purpose:
Space equipment (artificial satellites, rockets, etc.)/ Transportation vehicles and their control equipment (automobiles, aircraft, trains,
ships, etc.) / Medical equipment/ Relay equipment to be placed on sea floor/ Power station control equipment / Disaster or crime
prevention equipment/Traffic control equipment/ Financial equipment
Other applications requiring similar levels of reliability as the above
8. Epson products listed in this document and our associated technologies shall not be used in any equipment or systems that laws and
regulations in Japan or any other countries prohibit to manufacture, use or sell. Furthermore, Epson products and our associated
technologies shall not be used for the purposes of military weapons development (e.g. mass destruction weapons), military use, or any
other military applications. If exporting Epson products or our associated technologies, please be sure to comply with the Foreign
Exchange and Foreign Trade Control Act in Japan, Export Administration Regulations in the U.S.A (EAR) and other export-related laws
and regulations in Japan and any other countries and to follow their required procedures.
9. Epson assumes no responsibility for any damages (whether direct or indirect) caused by or in relation with your non-compliance with the
terms and conditions in this document or for any damages (whether direct or indirect) incurred by any third party that you give, transfer or
assign Epson products.
10. For more details or other concerns about this document, please contact our sales representative.
11. Company names and product names listed in this document are trademarks or registered trademarks of their respective companies.
10.Contact us
https://www5.epsondevice.com/en/contact/
5 Page
X1G005601019401 相关器件
| 型号 | 制造商 | 描述 | 价格 | 文档 |
| X1G005961004315 | SEIKO | CMOS Output Clock Oscillator, | 获取价格 |
|
| X1M000221001000 | SEIKO | LVDS Output Clock Oscillator, | 获取价格 |
|
| X1M000221001001 | SEIKO | LVDS Output Clock Oscillator, | 获取价格 |
|
| X1M000221001011 | SEIKO | LVDS Output Clock Oscillator, | 获取价格 |
|
| X1M000221001013 | SEIKO | LVDS Output Clock Oscillator, | 获取价格 |
|
| X1M000311001013 | SEIKO | LVPECL Output Clock Oscillator, | 获取价格 |
|
| X1M000311001213 | SEIKO | LVPECL Output Clock Oscillator, | 获取价格 |
|
| X1M000311001500 | SEIKO | LVPECL Output Clock Oscillator, | 获取价格 |
|
| X1M000311001501 | SEIKO | LVPECL Output Clock Oscillator, | 获取价格 |
|
| X1M000311001511 | SEIKO | LVPECL Output Clock Oscillator, | 获取价格 |
|
X1G005601019401 相关文章
Bourns 密封通孔金属陶瓷微调电位计产品选型手册(英文版)
- 2024-09-20
- 5
Bourns 精密环境传感器产品选型手册(英文版)
- 2024-09-20
- 8
Bourns POWrTher 负温度系数(NTC)热敏电阻手册 (英文版)
- 2024-09-20
- 8
Bourns GMOV 混合过压保护组件产品选型手册(英文版)
- 2024-09-20
- 6
