SC195FULTRT [SEMTECH]
3.5MHz, 500mA Synchronous Step Down DC-DC Regulator;型号: | SC195FULTRT |
厂家: | SEMTECH CORPORATION |
描述: | 3.5MHz, 500mA Synchronous Step Down DC-DC Regulator |
文件: | 总18页 (文件大小:581K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
SC195F
3.5MHz, 500mA Synchronous
Step Down DC-DC Regulator
POWER MANAGEMENT
Features
Description
Input Voltage — 2.9V to 5.5V
Output Voltage — 0.8V to 3.3V
Output current capability — 500mA
Efficiency up to 94%
15 Programmable output voltages
Fast transient response
Oscillator frequency — 3.5MHz
100% duty cycle capability
Quiescent current — 4.8 mA typ
Shutdown Current — 0.1µA typ
Internal soft-start
The SC195F is a high efficiency, 500mA step down regula-
tor designed to operate with an input voltage range of
2.9V to 5.5 V. The input voltage range makes it ideal for
battery operated applications with space limitations. The
SC195F operates at a fixed 3.5MHz switching frequency in
normal PWM (Pulse-Width Modulation) mode. The
SC195F also includes fifteen programmable output
voltage settings that can be selected using the four
control pins, eliminating the need for external feedback
resistors. The output voltage can be fixed to a single
setting or dynamically switched between different levels.
Pulling all four control pins low disables the output.
Over-voltage protection
Current limit and short circuit protection
Over-temperature protection
Input under-voltage lockout
Floating control pin protection
MLPQ-UT8 1.5 x 1.5 x 0.6 (mm) package
Pb free, halogen free, and RoHS/WEEE compliant
The SC195F provides several protection features to safe-
guard the device under stressed conditions. These
include short circuit protection, over-temperature protec-
tion, input under-voltage lockout, and soft-start to control
in-rush current. These features, coupled with the small
1.5 x 1.5 x 0.6 (mm) package make the SC195F a versatile
device ideal for step-down regulation in products needing
high efficiency and a small PCB footprint.
Applications
Smart phones and cellular phones
MP3/Personal media players
Personal navigation devices
Digital cameras
Single Li-ion cell or 3 NiMH/NiCd cell devices
Devices with 3.3V or 5V internal power rails
Typical Application Circuit
SC195F
LX
1.0µH
VIN
IN
2.9V to 5.5V
VOUT
0.8V to 3.3V
CIN
4.7µF
LX
OUT
CTL3
CTL2
CTL1
CTL0
COUT
10µF
Control Logic
Lines
GND
Rev 2.0
1
© 2016 Semtech Corporation
SC195F
Pin Configuration
Ordering Information
Device
Package
CTL3
SC195FULTRT(1)(2)
MLPQ-UT8 1.5 x 1.5
Evaluation Board
SC195FEVB
Notes:
(1) Available in tape and reel only. A reel contains 3,000 devices.
(2) Lead-free packaging only. Device is WEEE and RoHS compliant
and halogen-free.
8
1
2
3
CTL2
CTL1
7
6
5
IN
TOP VIEW
LX
CTL0
GND
4
OUT
MLPQ-UT8; 1.5 x 1.5, 8 LEAD
θJA = 116°C/W
Table 1 – Output Voltage Settings
CTL3
CTL2
CTL1
CTL0
Vout
Off
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
Marking Information
0.80
1.00
1.20
1.40
1.50
1.60
1.80
2.30
2.35
2.00
2.40
2.45
2.80
3.00
3.30
5F=SC195F
yw=Date Code
2
SC195F
Absolute Maximum Ratings
Recommended Operating Conditions
IN (V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to +6.0
LX Voltage (V). . . . . . . . . . . . . . . . . . . . . . . . . . . .-1.0 to VIN +0.5
Other Pins (V). . . . . . . . . . . . . . . . . . . . . . . . . . . .-0.3 to VIN + 0.3
Output Short Circuit to GND. . . . . . . . . . . . . . . . Continuous
ESD Protection Level(1) (kV) . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5
Input Voltage Range (V) . . . . . . . . . . . . . . . . . . . . . +2.9 to+5.5
Thermal Information
Thermal Resistance, Junction to Ambient(2) (°C/W). . . . 116
Junction Temperature Range (°C) . . . . . . . . . . . -40 to +150
Storage Temperature Range (°C). . . . . . . . . . . . -65 to +150
Exceeding the above specifications may result in permanent damage to the device or device malfunction. Operation outside of the parameters
specified in the Electrical Characteristics section is not recommended.
NOTES:
(1) Tested according to JEDEC standard JESD22-A114.
(2) Calculated from package in still air, mounted to 3 x 4.5 (in), 4 layer FR4 PCB per JESD51 standards.
Electrical Characteristics
Unless otherwise specified: VIN= 3.6V, CIN=4.7µF, COUT=10µF, LX=1µH, VOUT=2.0V, TJ(MAX)=125°C, TA= -40 to +85 °C. Typical values are TA=+25 °C
Parameter
Symbol
VOUT
Condition
Min
0.8
Typ
Max
3.3 (1)
2.0
Units
V
Output Voltage Range
Output Voltage Tolerance
Line Regulation
VOUT_TOL
ΔVLINEREG
ΔVLOADREG
IOUT
IOUT = 200mA
-2.0
%
2.9 ≤ VIN ≤ 5.5V, IOUT = 200mA
200mA ≤ IOUT ≤ 500mA
0.3
-1
%/V
%/A
mA
mA
mA
V
Load Regulation
Output Current Capability
Current Limit Threshold
Foldback Current Limit
500
800
ILIMIT
1300
2.9
IFB_LIM
ILOAD > ILIMIT
Rising VIN
150
Under-Voltage Lockout
VUVLO
Hysteresis
IOUT = 0mA
VCTL 0-3= 0V
Into LX pin
IOUT= 100mA
IOUT= 100mA
200
4.8
mV
mA
µA
Quiescent Current
IQ
ISD
Shutdown Current
0.1
1.0
1.0
LX Leakage Current
ILX
0.1
µA
High Side Switch Resistance(2)
Low Side Switch Resistance(3)
Switching Frequency
RDSON_P
RDSON_N
fSW
250
350
3.5
mΩ
2.8
4.2
MHz
3
SC195F
Electrical Characteristics (continued)
Parameter
Symbol
tSS
Condition
Min
Typ
350
160
20
Max
Units
µs
Soft-Start
VOUT = 90% of final value (4)
Rising temperature
500
Thermal Shutdown
Thermal Shutdown Hysteresis
TOT
°C
THYST
°C
Logic Inputs - CTL0, CTL1, CTL2, and CTL3
Input High Voltage
VIH
VIL
IIH
1.6
V
V
Input Low Voltage
0.4
5.0
2.0
Input High Current
VCTL 0-3= VIN
-2.0
-2.0
µA
µA
Input Low Current
Notes
IIL
VCTL 0-3= GND
(1) Maximum output voltage is limited to VIN if the input is less than 3.3V.
(2) Measured from IN to LX.
(3) Measured from LX to GND.
(4) Soft start time depends on the load and output capacitance, see Soft Start section.
4
SC195F
Typical Characteristics
CIN = 4.7µF, COUT = 10µF, LX = 1µH, TA = 25°C unless otherwise noted.
Efficiency vs. IOUT Vin=5V
Regulation vs. IOUT Vin=5V
Vin=5V
Vin=5V
94
3.5
3
VID=0.8V
92
VID=0.8V
VID=1V
90
88
86
84
82
80
78
76
74
72
70
68
66
64
62
60
58
56
54
52
50
VID=1V
VID=1.2V
VID=1.4V
VID=1.5V
VID=1.6V
VID=1.8V
VID=2V
VID=1.2V
VID=1.4V
VID=1.5V
VID=1.6V
VID=1.8V
VID=2V
2.5
2
VID=2.3V
VID=2.35V
VID=2.4V
VID=2.45V
VID=2.8V
VID=3V
VID=2.3V
VID=2.35
VID=2.4V
VID=2.45
VID=2.8V
VID=3V
1.5
1
VID=3.3V
VID=3.3V
0.5
0
0.1
0.2
0.3
0.4
0.5
0
0.1
0.2
0.3
0.4
0.5
Load Current (A)
Load Current (A)
Regulation vs. IOUT Vin=4.2V
Efficiency vs. IOUT Vin=4.2V
Vin=4.2V
Vin=4.2V
3.5
3
94
VID=0.8V
VID=1V
92
VID=0.8V
VID=1V
90
88
VID=1.2V
VID=1.4V
VID=1.5V
VID=1.6V
VID=1.8V
VID=2V
86
VID=1.2V
VID=1.4V
VID=1.5V
VID=1.6V
VID=1.8V
VID=2V
84
82
80
2.5
2
78
76
74
72
70
VID=2.3V
VID=2.35V
VID=2.4V
VID=2.45V
VID=2.8V
VID=3V
VID=2.3V
VID=2.35V
VID=2.4V
VID=2.45V
VID=2.8V
VID=3V
68
66
1.5
1
64
62
60
58
56
54
VID=3.3V
52
VID=3.3V
0.5
50
0
0.1
0.2
0.3
0.4
0.5
0
0.1
0.2
0.3
0.4
0.5
Load Current (A)
Load Current (A)
Efficiency vs. IOUT Vin=3.6V
Regulation vs. IOUT Vin=3.6V
Vin=3.6V
Vin=3.6V
3.5
3
98
96
94
92
90
88
86
84
82
80
78
76
74
72
70
68
66
64
62
60
58
56
54
52
50
VID=0.8V
VID=1V
VID=0.8V
VID=1V
VID=1.2V
VID=1.4V
VID=1.5V
VID=1.6V
VID=1.8V
VID=2V
VID=1.2V
VID=1.4V
VID=1.5V
VID=1.6V
VID=1.8V
VID=2V
2.5
2
VID=2.3V
VID=2.35V
VID=2.4V
VID=2.45V
VID=2.8V
VID=3V
VID=2.3V
VID=2.35V
VID=2.4V
VID=2.45V
VID=2.8V
VID=3V
1.5
1
VID=3.3V
VID=3.3V
0.5
0
0.1
0.2
0.3
0.4
0.5
0
0.1
0.2
0.3
0.4
0.5
Load Current (A)
Load Current (A)
5
SC195F
Typical Characteristics (continued)
Line Regulation (VOUT =1.8V)
Frequency vs. Temperature
IOUT = 200mA
1.86
4
3.8
3.6
3.4
1.84
1.82
1V
1.8V
2.8V
3.3V
-40°C
25°C
85°C
1.80
3.2
3
1.78
1.76
-40
-20
0
20
40
60
80
100
2.5
3.0
3.5
4.0
4.5
5.0
5.5
VIN (V)
Temperature (°C)
Light Load Soft-start
Heavy Load Soft-start
ILOAD = 500mA
ILOAD = 10mA
IIN (200mA/div)
IIN (200mA/div)
VOUT (1.0V/div)
ILX (500mA/div)
Vout (1.0V/div)
ILX (500mA/div)
Time (40μs/div)
Time (40μs/div)
Heavy Load Switching — VOUT = 3.3V
Heavy Load Switching — VOUT = 2.8V
VOUT (50mV/div)
VOUT (50mV/div)
VLX (2V/div)
VLX (2V/div)
ILX (200mA/div)
ILX (200mA/div)
Time (200ns/div)
Time (200ns/div)
6
SC195F
Typical Characteristics (continued)
Heavy Load Switching — VOUT = 1.0V
Heavy Load Switching — VOUT = 1.8V
VOUT (50mV/div)
VLX (2.0V/div)
VOUT (50mV/div)
VLX (2V/div)
ILX (200mA/div)
ILX (200mA/div)
Time (200ns/div)
Time (200ns/div)
Load Transient Response — 200 to 500mA
VID Transient Response — PWM
1.2V to 1.8V transition
VOUT (100mV/div)
VOUT (500mV/div)
ILX (200mA/div)
ILX (500mA/div)
ILOAD (500mA/div)
Time (20μs/div)
VCTL2 (2.0V/div)
Time (20μs/div)
Line Transient Response — PWM
Shutdown Transient Response
3.5V to 4.0V transition on VIN
VOUT (2V/div)
VOUT (100mV/div)
ILX (200mA/div)
ILX (200mA/div)
VIN 500mV/div)
VCTL3-0 (2V/div)
Time (20μs/div)
Time (20μs/div)
7
SC195F
Pin Descriptions
Pin
Pin Name
Pin Function
Control bit 2 — see Table 1, page 2, for decoding. This pin has a weak pull-down resistor (> 1MΩ) in place at
reset that is removed when CTL2 is pulled above the logic high threshold.
1
CTL2
Control bit 1 — see Table 1, page 2, for decoding. This pin has a weak pull-down resistor (> 1MΩ) in place at
reset that is removed when CTL1 is pulled above the logic high threshold.
2
3
4
CTL1
CTL0
OUT
Control bit 0 — see Table 1, page 2, for decoding. This pin has a weak pull-down resistor (> 1MΩ) in place at
reset that is removed when CTL0 is pulled above the logic high threshold.
Output voltage sense pin — output voltage regulation point (connection node of inductor and output
capacitor).
5
6
7
GND
LX
Ground reference and power ground for the SC195F.
Switching output — connect an inductor between this pin and the load to filter the pulsed output current.
Input power supply pin — connect a bypass capacitor from this pin to GND.
IN
Control bit 3 — see Table 1, page 2, for decoding. This pin has a weak pull-down resistor (> 1MΩ) in place at
reset that is removed when CTL3 is pulled above the logic high threshold.
8
CTL3
8
SC195F
Block Diagram
Plimit Amp
8
IN
Current Amp
OSC & Slope
Generator
Control
Logic
7
LX
PWM
Comp
500mV
Ref
Error Amp
PSAVE
Comp
Nlimit Amp
6
GND
4
3
2
1
CTL3
CTL2
CTL1
Voltage
Select
CTL0
OUT
5
9
SC195F
Applications Information
power state. Note that applying all zeros to the CTL pins
when changing the output voltages will temporarily
disable the device, so it is important to avoid this combi-
nation when dynamically changing levels.
General Description
The SC195F is a synchronous step-down Pulse Width
Modulated (PWM) DC-DC regulator utilizing a 3.5MHz
fixed-frequency voltage mode architecture. The device is
designed to operate in fixed-frequency PWM mode at all
load conditions. The device requires only two capacitors
and a single inductor to be implemented in most systems.
The switching frequency has been chosen to minimize the
size of the inductor and capacitors while maintaining high
efficiency. The output voltage is programmable, eliminat-
ing the need for external programming resistors. Loop
compensation is also internal, eliminating the need for
external components to control stability.
Adjustable Output Voltage Selection
If an output voltage other than one of the 15 program-
mable settings is needed, an external resistor divider
network can be added to the SC195F to adjust the output
voltage setting. This network scales the output based on
the resistor ratio and the programmed output setting.
The resistor values can be determined using the
equation
ª
º
R
FB1 ꢀ RFB2
RFB2
Programmable Output Voltage
VOUT VSET u
ꢀ ILEAK uRFB1
«
¬
»
¼
The SC195F has 15 fixed output voltage levels which can
be individually selected by programming the CTL control
pins (CTL3-0 — see Table 1 on page 2 for settings). The
device is disabled whenever all four CTL pins are pulled
low and enabled whenever at least one of the CTL pins is
pulled high. This configuration eliminates the need for a
dedicated enable pin. Each CTL pin is internally pulled
down via 1MΩ if VIN is below 1.5V or if the voltage on the
control pin is below the input high voltage. This ensures
that the output is disabled when power is applied if there
are no inputs to the CTL pins. Each weak pull-down is dis-
abled whenever its pin is pulled high and remains disabled
until all CTL pins are pulled low.
where VOUT is the desired output voltage, VSET is the voltage
setting selected by the CTL pins, RFB1 is the resistor
between the output capacitor and the OUT pin, RFB2 is the
resistor between the OUT pin and ground, and ILEAK is the
leakage current into the OUT pin during normal opera-
tion. The current into the OUT pin is typically 1µA, so the
last term of the equation can be neglected if the current
through RFB2 is much larger than 1µA. Selecting a resistor
value of 10kΩ or lower will simplify the design. If ILEAK is
neglected and RFB2 is fixed, RFB1 can be determined using
the equation
VOUT ꢀ VSET
RFB1 RFB2 u
VSET
The output voltage can be set using different approaches.
If a static output voltage is required, the CTL pins can be
tied to either IN or GND to set the desired voltage when-
ever power is applied at IN. If enable control is required,
each CTL pin can be tied to either GND or to a micropro-
cessor I/O line to create the desired control code whenever
the control signal is forced high. This approach is equiva-
lent to using the CTL pins collectively as a single enable
pin. A third option is to connect each of the four CTL pins
to individual microprocessor I/O lines. Any of the 15
output voltages can be programmed using this approach.
If only two output voltages are needed, the CTL pins can
be combined in a way that will reduce the number of I/O
lines to 1, 2, or 3, depending on the control code for each
desired voltage. Other CTL pins could be hard wired to
GND or IN. This option allows dynamic voltage adjust-
ment for systems that reduce the supply voltage at low
Inserting resistance in the feedback loop will adversely
affect the system’s transient performance if feed-forward
capacitance is not included in the circuit. The circuit in
Figure 1 illustrates how the resistor divider and feed-for-
ward capacitor can be added to the SC195F schematic.
The value of feed-forward capacitance needed can be
determined using the equation
2
VSET
ꢀ
VOUT ꢂ 0.5
ꢁ
CFF 4u10ꢂ6 u
RFB1
VOUT ꢂ VSET ꢁꢀVSET ꢂ 0.5
ꢀ ꢁ
10
SC195F
Applications Information (continued)
mode operation. An internal synchronous NMOS rectifier
turns on complementary to the top PMOSFET.
SC195F
LX
VIN
IN
VOUT
LX
OUT
GND
CFF
CIN
The duty cycle (percentage of time PMOS is active)
increases as VIN decreases to maintain output voltage
regulation. As the input voltage approaches the pro-
grammed output voltage, the duty cycle approaches
100% (PMOS always on) and the device enters a pass-
through mode until the input voltage increases or the
load decreases enough to allow PWM switching to
resume.
COUT
RFB1
CTL3
CTL2
CTL1
CTL0
RFB2
Enable
Figure 1 — Application Circuit with External Resistors
To simplify the design, it is recommended to program the
output setting to 1.0V, use resistor values smaller than
10kΩ, and include a feed-forward capacitance calculated
with the equation above. If the output voltage is set to
1.0V, the previous equation reduces to
Protection Features
The SC195F provides the following protection features:
• Current Limited Soft-Start Operation
• Over-Voltage Protection
• Current Limit
2
ꢀ
VOUT ꢂ 0.5
ꢁ
CFF 8u10ꢂ6 u
• Thermal Shutdown
RFB1
ꢀ
VOUT ꢂ1
ꢁ
• Input Voltage Under-Voltage Lockout
Example:
Soft-Start with Current Limit
An output voltage of 1.3V is desired, but this is not a pro-
grammable option. What external component values for
Figure 1 are needed?
The soft-start sequence is activated after a CTL code tran-
sition from an all zeros code to a non-zero code enables
the start up process. From the beginning of a start-up
process, the internal reference start-up takes typically
50μs, then PMOS current limit is stepped through four
levels: 25%, 40%, 60%, and 100%. Each step is maintained
for typically 75μs. A complete 4 steps start-up period
could take 350μs. Before VOUT reaches 90%, the inductor
current is not allowed to go negative. The inductor
current is confined between different current limit levels,
25%, 40%, 60%, or 100% to zero.
Solution: To keep the circuit simple, set RFB2 to 10kΩ so
current into the OUT pin can be neglected and set the
CTL3-0 pins to 0010 (1.0V setting). The necessary compo-
nent values for this situation are
VOUT ꢀ VSET
RFB1 RFB2
u
3k:
VSET
2
ꢀ
VOUT ꢂ 0.5
ꢁ
CFF 8 u10ꢂ6 u
5.69nF
As VOUT reaches 90% of the target value, the device will
transition into a fixed 3.5MHz operation allowing induc-
tor current in both directions.
RFB1
ꢀ
VOUT ꢂ1
ꢁ
PWM and 100% Duty Cycle Operation
Due to current limit operation, if the load is heavy or the
output capacitor is large, the soft start process may expe-
rience all 4 current limit steps before reaching 90% target
voltage. This will make the soft start time long. If the load
is light and output capacitor is small, the device may only
need the first current limit step, reaching 90% of target,
and transition into PWM operation. This makes the soft
start time shorter.
In order to start up from pre-charged output voltage,
SC195F does not allow inductor current to go negative in
soft start stage, refer to the soft start waveforms in the
Typical Characteristics page. When the output voltage
exceeds 90% of the set point, determined by the CTLx
combinations, the device will enter fixed 3.5MHz PWM
11
SC195F
Applications Information (continued)
Over-Voltage Protection
single-pole output filter corner frequency defined by the
equation
Over-voltage protection ensures the output voltage does
not rise to a level that could damage its load. When VOUT
exceeds the regulation voltage by 15%, the PWM drive is
disabled. Switching does not resume until VOUT has fallen
below the regulation voltage by 2%.
ꢁ
I&
ꢀS / u &287
where L = 1μH and COUT = 10μF.
When selecting output filter components, the LC product
should not vary over a wide range. Selection of smaller
inductor and capacitor values will move the corner fre-
quency, potentially impacting system stability.
Current Limit
The SC195F switching stage is protected by a current limit
function. If the output load exceeds the PMOS current
limit for 32 consecutive switching cycles, the device enters
fold-back current limit mode and the output current is
limited to approximately 150mA. Under these conditions,
the output voltage will be the product of IFB-LIM and the
load resistance. The load must fall below IFB-LIM for the
device to exit fold-back current limit mode. This function
makes the device capable of sustaining an indefinite short
circuit on its output under fault conditions.
It is also important to consider the change in inductance
with DC bias current when choosing an inductor. The
inductor saturation current is specified as the current at
which the inductance drops a specific percentage from
the nominal value (approximately 30%). Except for short-
circuit or other fault conditions, the peak current must
always be less than the saturation current specified by the
manufacturer. The peak current is the maximum load
current plus one half of the inductor ripple current at the
maximum input voltage. Load and/or line transients can
cause the peak current to exceed this level for short dura-
tions. Maintaining the peak current below the inductor
saturation specification keeps the inductor ripple current
and the output voltage ripple at acceptable levels.
Manufacturers often provide graphs of actual inductance
and saturation characteristics versus applied inductor
current. The saturation characteristics of the inductor can
vary significantly with core temperature. Core and
ambient temperatures should be considered when exam-
ining the core saturation characteristics.
Thermal Shutdown
The SC195F has a thermal shutdown feature to protect the
device if the junction temperature exceeds 160°C. During
thermal shutdown, the PMOS and NMOS switches are
both disabled, tri-stating the LX output. When the junc-
tion temperature drops by the hysteresis value (20°C), the
device goes through the soft-start process and resumes
normal operation.
Input Voltage Under-Voltage Lockout
Under-Voltage Lockout (UVLO) activates when the input
power supply voltage drops below the UVLO threshold.
This prevents the device from entering an ambiguous
state in which regulation cannot be maintained.
Hysteresis of approximately 200mV is included to prevent
chattering near the threshold.
When the inductor value has been determined, the DC
resistance (DCR) must be examined. Efficiency can be
optimized by lowering the inductor’s DCR as much as pos-
sible. Low DCR in an inductor requires either more surface
area for the increased wire diameter or fewer turns to
reduce the length of the copper winding. Fewer turns
requires an inductor core with a larger cross-sectional area
in order to maintain the same saturation characteristics.
The inductor size must always be considered when exam-
ining the inductor DCR to determine the best compromise
between DCR and component area on a PCB. Note that
the ripple component of the inductor is a small percent-
External Components
Inductor Selection
The SC195F is designed to operate with a suggested 1µH
inductor between the LX pin and the OUT pin.
The SC195F converter has internal loop compensation.
The compensation is designed to work with a specific
12
SC195F
Applications Information (continued)
age of the DC load. AC losses in the inductor core and
winding do not contribute significantly to the total
losses.
is due to its influence on the the loop crossover frequency,
phase margin, and gain margin. Increasing the output
capacitor above this minimum value will reduce the cross-
over frequency and provide greater phase margin.
Magnetic fields associated with the output inductor can
interfere with nearby circuitry. This can be minimized by
the use of low-noise shielded inductors which use the
minimum gap possible to limit the distance that magnetic
fields can radiate from the inductor. Shielded inductors,
however, typically have a higher DCR and are, therefore,
less efficient than a similar sized non-shielded inductor.
The output capacitor determines the output voltage
ripple and contributes load current during large step load
transitions. A capacitor between 10μF and 22μF will
usually be adequate in stabilizing the output during large
load transitions.
Capacitors with X7R or X5R ceramic dielectric are recom-
mended for their low ESR and superior temperature and
voltage characteristics. Y5V capacitors should not be used
as their temperature coefficients make them unsuitable
for this application.
Final inductor selection depends on various design con-
siderations such as efficiency, EMI, size, and cost. Table 2
lists the manufacturers of recommended inductor options.
The inductors with larger packages tend to provide better
overall efficiency, while the smaller package inductors
provide decent efficiency with reduced footprint or height.
The saturation current ratings and DC characteristics are
also shown.
In addition to ensuring stability, the output capacitor
serves other important functions. This capacitor deter-
mines the output voltage ripple — as capacitance
increases, ripple voltage decreases. It also supplies current
during a large load step for a few switching cycles until
the control loop responds (typically 3 switching cycles).
Once the loop responds, regulation is restored and the
desired output is reached. During the period prior to PWM
operation resuming, the relationship between output
voltage and output capacitance can be approximated
using the equation
Table 2 — Recommended Inductors
Saturation
Current
(mA)
L at
400mA
(μH)
Dimensions
LxWxH
Manufacturer
Part Number
L
(μH)
DCR
(Ω)
(mm)
Murata
LQM21PN1R0MC0
1.0 20% 0.19
1.0 20% 0.09
1.0 20% 0.12
1.0 20% 0.08
1.0 30% 0.08
1.0 30% 0.09
1.0 30% 0.08
1.3 30% 0.09
1.0 20% 0.18
800
1500
1200
800
0.75
0.95
0.95
0.88
1.00
1.00
0.78
1.20
0.90
2.0x1.25x0.55
2.5x2.0x1.1
3.2x1.6x0.85
2.5x2.0x1.0
2.0x1.25x1.0
2.0x1.25x1.0
2.5x2.0x0.5
2.5x2.0x1.2
1.6x0.8x0.8
Murata
LQM2HPN1R0MJ0
Murata
LQM31PN1R0M00
3u 'ILOAD
COUT
Taiyo Yuden
CKP25201R0M-T
VDROOP u f
Toko
1350
1100
1300
1200
850
MDT2012-CR1R0N
This equation can be used to approximate the minimum
output capacitance needed to ensure voltage does not
droop below an acceptable level. For example, a load step
from 50mA to 400mA requiring droop less than 50mV
would require the minimum output capacitance to be
FDK
MIPSZ2012D1R0
FDK
MIPSU2520D1R0
FDK
MIPSA2520D1R0
Taiyo Yuden
BRC1608T1R0M
3u0.4
COUT
6.0PF
0.05u 4u106
COUT Selection
The internal voltage loop compensation in the SC195F
In this example, using a standard 10µF capacitor would be
adequate to keep voltage droop less than the desired
limits the minimum output capacitor value to 10μF. This
13
SC195F
Applications Information (continued)
input voltage is twice the output voltage (50% duty cycle
scenario).
limit. Note that if the voltage droop limit were decreased
from 50mV to 25mV, the output capacitance would need
to be increased to at least 12µF (twice as much capaci-
tance for half the droop). Capacitance will decrease from
the nominal value when a ceramic capacitor is biased with
a DC current, so it is important to select a capacitor whose
value exceeds the necessary capacitance value at the pro-
grammed output voltage. Check the manufacturer’s
capacitance vs. DC voltage graphs when selecting an
output capacitor to ensure the capacitance will be
adequate.
The input capacitor provides a low impedance loop for
the edges of pulsed current drawn by the PMOS switch.
Low ESR/ESL X5R ceramic capacitors are recommended
for this function. To minimize stray inductance, the capaci-
tor should be placed as closely as possible to the IN and
GND pins of the SC195F. Table 4 lists the recommended
input capacitor options from different manufacturers.
Table 4 — Recommended Input Capacitors
Rated
Dimensions
Manufacturer
Part Nunber
Value
(μF)
Type
Voltage LxWxH (mm)
Table 3 lists the manufacturers of recommended output
capacitor options.
(VDC)
Case Size
Murata
GRM188R60J475K
1.6x0.8x0.8
0603
4.7 10%
10 10%
4.7 10%
4.7 10%
X5R
X5R
X5R
X5R
6.3
Table 3 — Recommended Output Capacitors
Murata
GRM188R60J106K
1.6x0.8x0.8
0603
6.3
Rated
Dimensions
Manufacturer
Part Nunber
Value
(μF)
Type Voltage LxWxH (mm)
Taiyo Yuden
JMK107BJ475KA
1.6x0.8x0.8
0603
6.3
(VDC)
Case Size
TDK
1.6x0.8x0.8
0603
Murata
GRM188R60J106ME47D
1.6x0.8x0.8
0603
6.3
10 20%
10 10%
10 20%
10 20%
X5R
X5R
X5R
X5R
6.3
C1608X5R0J475KT
Murata
GRM21BR60J106K
2.0x1.25x1.25
0805
6.3
PCB Layout Considerations
Taiyo Yuden
JMK107BJ106MA-T
1.6x0.8x0.8
0603
6.3
The layout diagram in Figure 2 shows a recommended
PCB top-layer for the SC195F and supporting compo-
nents. Specified layout rules must be followed since the
layout is critical for achieving the performance specified in
the Electrical Characteristics table. Poor layout can
degrade the performance of the DC-DC converter and can
contribute to EMI problems, ground bounce, and resistive
voltage losses. Poor regulation and instability can result.
TDK
1.6x0.8x0.8
0603
6.3
C1608X5R0J106MT
CIN Selection
The SC195F input current will appear as a pulse DC
current. To prevent large input voltage ripple, a low ESR
ceramic capacitor is required. A minimum value of 4.7μF
should be used. It is important to consider the DC voltage
coefficient characteristics when determining the actual
required value. For example, a 10μF, 6.3V, X5R ceramic
capacitor with 5V DC applied may exhibit a capacitance as
low as 4.5μF. The value of required input capacitance is
estimated by determining the acceptable input ripple
voltage and calculating the minimum value required for
CIN using the equation
The following guidelines are recommended for designing
a PCB layout:
1. CIN should be placed as close to the IN and GND pins
as possible. This capacitor provides a low impedance
loop for the pulsed currents present at the buck
converter’s input. Use short wide traces to minimize
trace impedance. This will also minimize EMI and
input voltage ripple by localizing the high frequency
current pulses.
2. Keep the LX pin traces as short as possible to minimize
pickup of high frequency switching edges to other
parts of the circuit. COUT and LX should be connected
as close as possible between the LX and GND pins,
with a direct return to the GND.
§
·
VOUT
VOUT
¨
¨
¸
¸
1ꢀ
V
V
IN
©
IN
¹
CIN
§
·
'V
IOUT
¨
¨
¸
ꢀESR f
¸
©
¹
The input voltage ripple is at maximum level when the
14
SC195F
Applications Information (continued)
3. Use a ground plane referenced to the GND pin. Use
several vias to connect to the component side ground
to further reduce noise and interference on sensitive
circuit nodes.
4.8mm
4. Route the output voltage feedback/sense path away
from the inductor and LX node to minimize noise and
magnetic interference.
5. Minimize the resistance from the OUT and GND pins
to the load. This will reduce errors in DC regulation
due to voltage drops in the traces.
CIN
LX
CTL3
3mm
CTL2
CTL1
CTL0
SC195F
COUT
Figure 2 — Recommended PCB Layout
15
SC195F
Outline Drawing — MLPQ-UT8
A
D
B
E
DIMENSIONS
INCHES MILLIMETERS
DIM
A
MIN NOM MAX MIN NOM MAX
-
-
-
-
.020
A1 .000
A2
.024 0.50
.002 0.00
0.60
0.05
(.006)
(0.1524)
PIN 1
INDICATOR
(LASER MARK)
b
D
E
e
.006 .008 .010 0.15 0.20 0.25
.059 BSC
.059 BSC
.016 BSC
1.50 BSC
1.50 BSC
0.40 BSC
L
N
0.12 .014 0.16 0.30 0.35 0.40
8
8
aaa
bbb
.004
.004
0.10
0.10
A2
A
SEATING
PLANE
aaa C
C
A1
LxN
e
2
1
0.20
0.17
0.25
N
bxN
bbb
C A B
NOTES:
1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES).
16
SC195F
Suggested Land Pattern — MLPQ-UT8
Z
DIMENSIONS
G
DIM
INCHES
MILLIMETERS
(.057)
.028
.016
.004
.008
.030
.087
(1.45)
0.70
0.40
0.10
0.20
0.75
2.20
C
G
P
R
X
Y
Z
P
(Z)
(G)
2X (C)
X
R
Y
NOTES:
1.
CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES).
2. THIS LAND PATTERN IS FOR REFERENCE PURPOSES ONLY.
CONSULT YOUR MANUFACTURING GROUP TO ENSURE YOUR
COMPANY'S MANUFACTURING GUIDELINES ARE MET.
17
SC195F
© Semtech 2016
All rights reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright
owner. The information presented in this document does not form part of any quotation or contract, is believed to be
accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any conse-
quence of its use. Publication thereof does not convey nor imply any license under patent or other industrial or
intellectual property rights. Semtech assumes no responsibility or liability whatsoever for any failure or unexpected
operation resulting from misuse, neglect improper installation, repair or improper handling or unusual physical or elec-
trical stress including, but not limited to, exposure to parameters beyond the specified maximum ratings or operation
outside the specified range.
SEMTECH PRODUCTS ARE NOT DESIGNED, INTENDED, AUTHORIZED OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-
SUPPORT APPLICATIONS, DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF SEMTECH PRODUCTS
IN SUCH APPLICATIONS IS UNDERSTOOD TO BE UNDERTAKEN SOLELY AT THE CUSTOMER’S OWN RISK. Should a customer
purchase or use Semtech products for any such unauthorized application, the customer shall indemnify and hold
Semtech and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs damages
and attorney fees which could arise.
Notice: All referenced brands, product names, service names and trademarks are the property of their respective
owners.
Contact Information
Semtech Corporation
Power Management Products Division
200 Flynn Road, Camarillo, CA 93012
Phone: (805) 498-2111 Fax: (805) 498-3804
www.semtech.com
18
相关型号:
SC1972
NPN EPITAXIAL PLANAR TYPE(for RF power amplifiers on VHF band Mobile radio applications)
MITSUBISHI
©2020 ICPDF网 联系我们和版权申明