74AVCH2T45 [SGMICRO]
2-Bit Dual-Supply Voltage Level Transceiver with 3-State Outputs;型号: | 74AVCH2T45 |
厂家: | Shengbang Microelectronics Co, Ltd |
描述: | 2-Bit Dual-Supply Voltage Level Transceiver with 3-State Outputs |
文件: | 总6页 (文件大小:433K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
74AVCH2T45
2-Bit Dual-Supply Voltage
Level Transceiver with 3-State Outputs
GENERAL DESCRIPTION
FEATURES
The 74AVCH2T45 is a 2-bit, dual-supply voltage level
transceiver. The nA and nB are two data input-output
ports, DIR is a direction control input, and VCCA and
● VCCA Supply Voltage Range: 0.8V to 3.6V
● VCCB Supply Voltage Range: 0.8V to 3.6V
● Inputs Accept Voltages up to 3.6V
● +12mA/-12mA Output Current
VCCB are dual-supply pins. The supply voltage of VCCA
and VCCB can range from 0.8V to 3.6V, making the
device suitable for translating among any of the 0.8V,
1.2V, 1.5V, 1.8V, 2.5V and 3.3V voltage nodes. The nA
and DIR signals are referenced to VCCA and nB signals
● Data Rates:
500Mbps (1.8V to 3.3V Translation)
320Mbps (< 1.8V to 3.3V Translation)
320Mbps (Translate to 2.5V or 1.8V)
280Mbps (Translate to 1.5V)
are referenced to VCCB
.
240Mbps (Translate to 1.2V)
When DIR is set high, it allows transmission from nA to
nB. When DIR is set low, it allows transmission from nB
to nA. In suspend mode, when either VCCA or VCCB input
is at GND, both nA and nB are in the high-impedance
state.
● Outputs in High-Impedance State when VCCA or
VCCB = 0V
● No External Pull-up/Pull-down Resistors are
Required Due to the Bus Hold on Data Inputs
● -40℃ to +125℃ Operating Temperature Range
● Available in a Green VSSOP-8 Package
This device is highly suitable for partial power-down
applications using power-off leakage current (IOFF) circuit.
When the device is powered down, the current backflow
will be prevented from passing through the device.
The active bus hold circuitry makes device unnecessary
to use external pull-up/pull-down resistors by holding
unused or floating data inputs at a valid logic level.
FUNCTION TABLE
SUPPLY
CONTROL
INPUT
INPUT/OUTPUT (1)
VOLTAGE
VCCA, VCCB
0.8V to 3.6V
0.8V to 3.6V
GND (3)
DIR (2)
nA
nA = nB
Inputs
Z
nB
Inputs
nB = nA
Z
LOGIC DIAGRAM
L
H
X
5
DIR
H = High Voltage Level
L = Low Voltage Level
X = Don’t Care
2
1A
7
Z = High-Impedance State
1B
3
NOTES:
2A
1. For the I/O data, the input circuit is always active.
2. The DIR pin is referenced to VCCA.
6
2B
3. If at least one of VCCA or VCCB is at GND level, the device
enters suspend mode.
SG Micro Corp
NOVEMBER 2022 – REV. A
www.sg-micro.com
2-Bit Dual-Supply Voltage
74AVCH2T45
Level Transceiver with 3-State Outputs
PACKAGE/ORDERING INFORMATION
SPECIFIED
TEMPERATURE
RANGE
PACKAGE
DESCRIPTION
ORDERING
NUMBER
PACKAGE
MARKING
PACKING
OPTION
MODEL
MEH
XXXX
74AVCH2T45
VSSOP-8
-40℃ to +125℃
74AVCH2T45XVS8G/TR
Tape and Reel, 3000
MARKING INFORMATION
NOTE: XXXX = Date Code, Trace Code and Vendor Code.
Serial Number
Y Y Y
X X X X
Vendor Code
Trace Code
Date Code - Year
Green (RoHS & HSF): SG Micro Corp defines "Green" to mean Pb-Free (RoHS compatible) and free of halogen substances. If
you have additional comments or questions, please contact your SGMICRO representative directly.
ABSOLUTE MAXIMUM RATINGS (1)
Input Transition Rise or Fall Rate, Δt/ΔV
Supply Voltage Range, VCCA............................. -0.5V to 4.6V
Supply Voltage Range, VCCB............................. -0.5V to 4.6V
Input Voltage Range, VI (2) ................................ -0.5V to 4.6V
VCCI = 0.8V to 3.6V .......................................... 5ns/V (MAX)
Operating Temperature Range..................... -40℃ to +125℃
(2)
Output Voltage Range, VO
OVERSTRESS CAUTION
Suspend or 3-State Mode............................... -0.5V to 4.6V
Active Mode
1. Stresses beyond those listed in Absolute Maximum
Ratings may cause permanent damage to the device.
Exposureto absolute maximum rating conditions for extended
periods may affect reliability. Functional operation of the
device at any conditions beyond those indicated in the
Recommended Operating Conditions section is not implied.
A Ports..............................-0.5V to MIN (4.6V, VCCA + 0.5V)
B Ports..............................-0.5V to MIN (4.6V, VCCB + 0.5V)
Output Current, IO (VO = 0V to VCCO
)
High-State or Low-State ..........................................±50mA
Input Clamp Current, IIK (VI < 0)...................................-50mA
Output Clamp Current, IOK (VO < 0V) ...........................-50mA
Supply Current, ICC (ICCA or ICCB).................................100mA
Ground Current, IGND..................................................-100mA
Junction Temperature (3) .............................................+150℃
Storage Temperature Range.......................-65℃ to +150℃
Lead Temperature (Soldering, 10s)............................+260℃
ESD Susceptibility
2. The minimum input voltage ratings and output voltage
ratings may be exceeded if the input and output current ratings
are observed.
3. The performance capability of a high-performance integrated
circuit in conjunction with its thermal environment can create
junction temperatures which are detrimental to reliability.
HBM.............................................................................6000V
CDM ............................................................................1000V
ESD SENSITIVITY CAUTION
This integrated circuit can be damaged if ESD protections are
not considered carefully. SGMICRO recommends that all
integrated circuits be handled with appropriate precautions.
Failureto observe proper handlingand installation procedures
can cause damage. ESD damage can range from subtle
performance degradation tocomplete device failure. Precision
integrated circuits may be more susceptible to damage
because even small parametric changes could cause the
device not to meet the published specifications.
RECOMMENDED OPERATING CONDITIONS
Supply Voltage Range, VCCA...............................0.8V to 3.6V
Supply Voltage Range, VCCB...............................0.8V to 3.6V
Input Voltage Range, VI .........................................0V to 3.6V
Output Voltage Range, VO
Suspend or 3-State Mode....................................0V to 3.6V
Active Mode
A Ports.................................................................0V to VCCA
B Ports.................................................................0V to VCCB
High-State or Low-State Output Current, IO ................±12mA
DISCLAIMER
SG Micro Corp reserves the right to make any change in
circuit design, or specifications without prior notice.
SG Micro Corp
www.sg-micro.com
NOVEMBER 2022
2
2-Bit Dual-Supply Voltage
74AVCH2T45
Level Transceiver with 3-State Outputs
PIN CONFIGURATION
(TOP VIEW)
VCCA
1A
VCCB
1B
1
2
8
7
2A
2B
3
4
6
5
GND
DIR
VSSOP-8
PIN DESCRIPTION
PIN
1
NAME
VCCA
FUNCTION
Supply Voltage VCCA. The nA and DIR signals are referenced to VCCA
.
2, 3
4
1A, 2A
GND
Data Inputs/Outputs.
Ground.
5
DIR
Direction Control Input.
7, 6
8
1B, 2B
VCCB
Data Inputs/Outputs.
Supply Voltage VCCB. The nB signals are referenced to VCCB.
SG Micro Corp
www.sg-micro.com
NOVEMBER 2022
3
PACKAGE INFORMATION
PACKAGE OUTLINE DIMENSIONS
VSSOP-8
D
e
E1
E
3.10
0.75
b
0.25
0.50
RECOMMENDED LAND PATTERN (Unit: mm)
L
ccc C
A2
A1
A
SEATING PLANE
θ
c
L1
C
Dimensions In Millimeters
Symbol
MIN
-
MOD
MAX
1.000
0.150
0.850
0.270
0.230
2.100
2.400
3.200
A
A1
A2
b
-
-
0.000
0.600
0.170
0.080
1.900
2.200
3.000
-
c
D
-
E
-
E1
e
-
0.500 BSC
L
0.150
0°
-
0.120 BSC
-
0.400
8°
L1
θ
ccc
0.100
NOTES:
1. This drawing is subject to change without notice.
2. The dimensions do not include mold flashes, protrusions or gate burrs.
3. Reference JEDEC MO-187 CA.
SG Micro Corp
TX00317.001
www.sg-micro.com
PACKAGE INFORMATION
TAPE AND REEL INFORMATION
REEL DIMENSIONS
TAPE DIMENSIONS
P2
P0
W
Q2
Q4
Q2
Q4
Q2
Q4
Q1
Q3
Q1
Q3
Q1
Q3
B0
Reel Diameter
P1
A0
K0
Reel Width (W1)
DIRECTION OF FEED
NOTE: The picture is only for reference. Please make the object as the standard.
KEY PARAMETER LIST OF TAPE AND REEL
Reel Width
Reel
Diameter
A0
B0
K0
P0
P1
P2
W
Pin1
Package Type
W1
(mm)
(mm) (mm) (mm) (mm) (mm) (mm) (mm) Quadrant
VSSOP-8
7″
9.5
2.25
3.35
1.05
4.0
4.0
2.0
8.0
Q3
SG Micro Corp
TX10000.000
www.sg-micro.com
PACKAGE INFORMATION
CARTON BOX DIMENSIONS
NOTE: The picture is only for reference. Please make the object as the standard.
KEY PARAMETER LIST OF CARTON BOX
Length
(mm)
Width
(mm)
Height
(mm)
Reel Type
Pizza/Carton
7″ (Option)
7″
368
442
227
410
224
224
8
18
SG Micro Corp
www.sg-micro.com
TX20000.000
相关型号:
74AVCH2T45DC
Dual-bit, dual-supply voltage level translator/transceiver; 3-stateProduction
NEXPERIA
74AVCH2T45DC-Q100
Dual-bit, dual-supply voltage level translator/transceiver; 3-stateProduction
NEXPERIA
74AVCH2T45DCTRE4
DUAL-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS
TI
74AVCH2T45DCTRG4
DUAL-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS
TI
74AVCH2T45DCTTE4
DUAL-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS
TI
74AVCH2T45DCURE4
DUAL-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS
TI
74AVCH2T45DCURG4
DUAL-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS
TI
74AVCH2T45DCUTE4
DUAL-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS
TI
74AVCH2T45DCUTG4
DUAL-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS
TI
74AVCH2T45GD,125
74AVCH2T45 - Dual-bit, dual-supply voltage level translator/transceiver; 3-state SON 8-Pin
NXP
©2020 ICPDF网 联系我们和版权申明