SGM31324 [SGMICRO]
Automatic Blink Mode, RGB LED Driver with I2C Interface;型号: | SGM31324 |
厂家: | Shengbang Microelectronics Co, Ltd |
描述: | Automatic Blink Mode, RGB LED Driver with I2C Interface |
文件: | 总17页 (文件大小:719K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
SGM31324
Automatic Blink Mode,
RGB LED Driver with I2C Interface
GENERAL DESCRIPTION
FEATURES
The SGM31324 is a 3-channel, current-regulated RGB
LED driver with an I2C-compatible interface. It is well
suited for various applications powered by a 1-cell
Li-Ion or Li-Polymer, or systems with 3.3V or 5V supply
voltages, as well as 3-cell NiCd, NiMH or Alkaline
batteries. No external components are required for the
three constant current sinks.
● Input Voltage Range: 2.5V to 5.5V
● Ultra-Low 30mV Dropout Voltage at a 10mA Load
per String
● Programmable LED Current through I2C Interface
● 0.125mA to 24mA Current Levels with 0.125mA
Steps
● Automatic Blink Mode on D1 Pin
Maximum LED1 Current: 8mA
Blinking Period: 2s
With two programmable timers, users can adjust LED
blinking time and get the result of fade-in and fade-out for
unique color lighting.
● Independent Channel Control
ON/OFF State Interval Time Control
RGB LED Color Control
Programmable I2C interface allows independent channel
control for LED ON or OFF state and LED brightness due
to 10 internal registers and an internal decoder. Each
current sink can be independently configured with
192-step current levels from 0.125mA to 24mA. The
SGM31324 provides less than 1μA shutdown current.
Programmable Ramp-Up and Ramp-Down Time
● No Noise and Constant LED Current
● Fast and Smooth Startup
● Less than 1μA Shutdown Current
● -40℃ to +85℃ Operating Temperature Range
● Available in a Green UTDFN-1.5×1.5-8L Package
An automatic blink mode allows the LED on D1 pin
(LED1) ON/OFF automatically at an 8mA load every 2
seconds after the EN pin is pulled high.
APPLICATIONS
The SGM31324 is available in a Green UTDFN-
1.5×1.5-8L package. It operates over an ambient
temperature range of -40℃ to +85℃.
Multi-Color LEDs
RGB Indicator LEDs
Impact LED Signs and Displays
Handheld Equipment
TYPICAL APPLICATION
VIN
2.5V to 5.5V
5
CIN
1.0μF
VIN
4
3
2
1
6
D1
D2
D3
EN
GPIO
I2C Control SCL
SCL
SDA
7
I2C Control SDA
GND
8
3 channels
in parallel
Figure 1. Typical Application Circuit
SG Micro Corp
JUNE2018–REV. A.1
www.sg-micro.com
Automatic Blink Mode,
SGM31324
RGB LED Driver withI2C Interface
PACKAGE/ORDERING INFORMATION
SPECIFIED
TEMPERATURE
RANGE
PACKAGE
DESCRIPTION
ORDERING
NUMBER
PACKAGE
MARKING
PACKING
OPTION
MODEL
GGB
XXX
SGM31324 UTDFN-1.5×1.5-8L
SGM31324YUDW8G/TR
Tape and Reel, 4000
-40℃ to +85℃
MARKING INFORMATION
NOTE: XXX = Date Code.
Serial Number
GGB
X XX
Date code - Week (01, 02, 03 …)
Date code - Year ("A" = 2010, "B" = 2011 …)
Green (RoHS & HSF): SG Micro Corp defines "Green" to mean Pb-Free (RoHS compatible) and free of halogen substances. If
you have additional comments or questions, please contact your SGMICRO representative directly.
ABSOLUTE MAXIMUM RATINGS
ESD SENSITIVITY CAUTION
VIN, D1, D2, D3 to GND...................................... -0.3V to 6V
EN to GND........................................................... -0.3V to 6V
SCL, SDA to GND ....................................-0.3V to VIN + 0.3V
Package Thermal Resistance
This integrated circuit can be damaged by ESD if you don’t
pay attention to ESD protection. SGMICRO recommends that
all integrated circuits be handled with appropriate precautions.
Failureto observe proper handlingand installation procedures
can cause damage. ESD damage can range from subtle
performance degradation tocomplete device failure. Precision
integrated circuits may be more susceptible to damage
because very small parametric changes could cause the
device not to meet its published specifications.
UTDFN-1.5×1.5-8L, θJA .......................................... 99.5℃/W
Junction Temperature.................................................+150℃
Storage Temperature Range.......................-65℃ to +150℃
Lead Temperature (Soldering, 10s)............................+260℃
ESD Susceptibility
HBM.............................................................................4000V
MM.................................................................................400V
CDM ............................................................................1000V
DISCLAIMER
SG Micro Corp reserves the right to make any change in
circuitdesign, specificationor other related things if necessary
without notice at any time.
RECOMMENDED OPERATING CONDITIONS
Input Voltage Range...........................................2.5V to 5.5V
Operating Temperature Range......................-40℃ to +85℃
OVERSTRESS CAUTION
Stresses beyond those listed may cause permanent damage
to the device. Functional operation of the device at these or
any otherconditions beyond those indicated in the operational
sectionof thespecificationis not implied. Exposureto absolute
maximum rating conditions for extended periods may affect
reliability.
SG Micro Corp
www.sg-micro.com
JUNE 2018
2
Automatic Blink Mode,
SGM31324
RGB LED Driver withI2C Interface
PIN CONFIGURATION
(TOP VIEW)
EN
D3
D2
D1
1
2
3
4
8
7
6
5
GND
SDA
SCL
VIN
GND
UTDFN-1.5×1.5-8L
PIN DESCRIPTION
NAME
EN
PIN
1
TYPE
FUNCTION
Automatic Blink Mode Enable Pin. Pull it high to enable this mode, and pull it low to
disable this mode. This pin is only used for automatic blink mode control.
I
O
O
O
P
Current Sink 3. The LED current level and ON/OFF states can be set by I2C
interface.
D3
2
Current Sink 2. The LED current level and ON/OFF states can be set by I2C
interface.
D2
3
Current Sink 1. Current level and ON/OFF selections are controlled by serial
interface.
D1
4
VIN
SCL
SDA
GND
GND
5
Input Supply Pin.
6
I
I2C Clock Signal.
7
I/O
G
―
I2C Data Signal.
8
Ground Pin.
Exposed
Pad
Exposed Pad. It should be soldered to the ground.
NOTE: I: input; O: output; I/O: input or output; G: ground; P: power for the circuit.
SG Micro Corp
www.sg-micro.com
JUNE 2018
3
Automatic Blink Mode,
SGM31324
RGB LED Driver withI2C Interface
ELECTRICAL CHARACTERISTICS
(VIN = 3.6V, Full = -40℃ to +85℃, typical values are at TA = +25℃, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
TEMP MIN
TYP
MAX UNITS
POWER SUPPLY
Input Operating Range
VIN
Full
2.5
5.5
90
5
V
mV
%
Sink Pin (Dx) Dropout Voltage
(90% of Nominal Current)
VD_MIN
All channels set to 24mA, REG6-8 = BFh
All channels set to 10mA, REG6-8 = 4Fh
65
+25℃
+25℃
+25℃
Output Current Accuracy
-5
-5
Max(|IDx - IAVG|)/IAVG, all channels set to 10mA,
REG6-8 = 4Fh
Output Current Matching
5
%
All channels set to 20mA, REG6-8 = 9Fh
One channel set to 20mA, other channels off
Device on, all LEDs OFF, Reg4 = 0
280
120
41
340
150
52
+25℃
+25℃
+25℃
+25℃
Supply Current
IIN
μA
Quiescent Current
Shutdown Current
IQ
μA
μA
ISHDN
VIN = VOUT = 3.6V, SCL = 0V, SDA = 0V
0.3
1
CONTROL AND I2C-COMPATIBLE PIN VOLTAGE SPECIFICATIONS (SCL, SDA) (1)
Input Logic Low Threshold
Input Logic High Threshold
VIL
VIH
SDA, SCL
SDA, SCL
0.4
V
V
+25℃
+25℃
1.2
I2C-COMPATIBLE TIMING SPECIFICATIONS (SCL, SDA), SEE Figure 4
SCL (Clock Period)
t1
t2
t3
t4
t5
t6
t7
2.5
1.3
350
0
μs
μs
ns
μs
ns
ns
ns
+25℃
+25℃
+25℃
+25℃
+25℃
+25℃
+25℃
Low Period of The SCL Clock
DATA_IN Setup Time to SCL High
DATA_IN Hold Time after SCL Low
DATA_OUT Stable after SCL Low
SDA Low Setup Time to SCL Low (Start)
SCL High Setup Time to SDA High (Stop)
THERMAL SHUTDOWN
0.8
350
600
600
Thermal Shutdown Threshold
Thermal Shutdown Hysteresis
140
15
℃
℃
SG Micro Corp
www.sg-micro.com
JUNE 2018
4
Automatic Blink Mode,
SGM31324
RGB LED Driver withI2C Interface
TYPICAL PERFORMANCE CHARACTERISTICS
TA = +25℃, VIN = 3.6V, CIN = 1μF, unless otherwise noted.
Quiescent Current vs. Input Voltage (LEDs Off)
Quiescent Current vs. Input Voltage (LEDs On)
0.3
0.25
0.2
0.4
0.35
0.3
0.15
0.1
0.25
0.2
0.05
0
0.15
0.1
2.5
3
3.5
4
4.5
5
5.5
2.5
3
3.5
4
4.5
5
5.5
200
5.5
Input Voltage (V)
Input Voltage (V)
LED Current Variation vs. Input Voltage (at 10mA)
VDX = 0.5V
LED Current vs. Dx Pin Voltage
10
5
25
20
15
10
5
20mA
0
10mA
-5
5mA
-10
-15
0
2.5
3
3.5
4
4.5
5
5.5
0
40
80
120
160
Input Voltage (V)
Dx Pin Voltage (mV)
LED Current vs. Input Voltage (10mA per Channel)
VDX = 0.5V
Logic Threshold vs. Input Voltage
25
20
15
10
5
1
0.9
0.8
0.7
0.6
0.5
VIH
ID3
ID2
ID1
VIL
0
2.5
3
3.5
4
4.5
5
5.5
2.5
3
3.5
4
4.5
5
Input Voltage (V)
Input Voltage (V)
SG Micro Corp
www.sg-micro.com
JUNE 2018
5
Automatic Blink Mode,
SGM31324
RGB LED Driver withI2C Interface
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
TA = +25℃, VIN = 3.6V, CIN = 1μF, unless otherwise noted.
Linear Ramps
Logarithmic-S Ramps
DX
DX
Filtered
ILED
Filtered
ILED
ILED
ILED
Time (100ms/div)
Time (100ms/div)
Flashing LED, 2ms Period
Flashing LED, Extended Falling Ramp
DX
DX
Filtered
ILED
Filtered
ILED
ILED
ILED
Time (500ms/div)
Time (500ms/div)
LED Current Transient 5mA to 20mA
Shutdown Mode Delay (Enable Control SDA toggling)
SDA
DX
SDA
DX
ILED
ILED
Time (200ms/div)
Time (200ms/div)
SG Micro Corp
www.sg-micro.com
JUNE 2018
6
Automatic Blink Mode,
SGM31324
RGB LED Driver withI2C Interface
I2C INTERFACE
1
0
9
1
9
1
9
…
…
…
S
1
1
0
0
0
0
W
A
B7 B6 B5 B4 B3 B2 B1 B0
A
D7 D6 D5 D4 D3 D2 D1 D0
A
P
Slave Address
Register Address
Write Data
Figure 2. I2C Write Sequence for a Single Register
1
0
9
1
9
1
9
…
…
…
S
1
1
0
0
0
0
R
A
B7 B6 B5 B4 B3 B2 B1 B0
A
D7 D6 D5 D4 D3 D2 D1 D0
N
P
Slave Address
Register Address
Read Data
Figure 3. I2C Read Sequence for a Single Register
NOTES:
1.
By Master,
By Slave.
S: Start, P: Stop, W: Write, R: Read, A: Acknowledge (SDA Low), N: Not Acknowledge (SDA High).
SG Micro Corp
www.sg-micro.com
JUNE 2018
7
Automatic Blink Mode,
SGM31324
RGB LED Driver withI2C Interface
REGISTER MAP
All registers are 8-bit and individual bits are named from D[0] (LSB) to D[7] (MSB).
R/W:
R:
Read/Write bit(s)
Read only bit(s)
PORV: Power-On Reset Value
Table 1. Register Map
REGISTER
FUNCTION
NAME
D[7]
D[6]
D[5]
D[4]
D[3]
D[2]
D[1]
D[0]
REG0
REG1
REG2
REG3
REG4
REG5
REG6
REG7
REG8
REG9
Enable/Reset
Flash Period
PWM1 Timer
PWM2 Timer
Channel Control
Ramp Rate
TEST_FAC
RAMP_LINE
TM_SCAL[1:0]
EN_CTRL[1:0]
FLASH_PERIOD[6:0]
TS_RST_MODE[2:0]
PWM1_TM_PER[7:0]
PWM2_TM_PER[7:0]
Reserved
DEV_EN
LED3_EN_TM[1:0]
LED2_EN_TM[1:0]
LED1_EN_TM[1:0]
RISE_TM[3:0]
FALL_TM[3:0]
I_LED1[7:0]
LED1 Current
LED2 Current
LED3 Current
I_LED2[7:0]
I_LED3[7:0]
LED1 Automatic Blink AUTO_ST
Reserved
AUTO_EN
REG0
Table 2. REG0 Register Details
BITS
BIT NAME
DESCRIPTION
PORV
D[7]
TEST_FAC
Test Only. It should be set to 0.
0
Rise or Fall Scaling Factor
00 = 1× Normal (default)
01 = 2× Slower
10 = 4× Slower
11 = 8× Faster
D[6:5]
D[4:3]
TM_SCAL[1:0]
EN_CTRL[1:0]
00
Enable Control
00 = Device ON at SCL = high and SDA = high.
When either SDA or SCL goes low, the device goes into shutdown mode. (default)
01 = Device ON at SCL = high and SDA toggling.
When either SCL goes low or SDA stops toggling, the device goes into shutdown mode.
10 = Device ON at SCL = high regardless of SDA state.
When SCL goes low, the device goes into shutdown mode.
11 = Device always ON.
00
Timer Slot Control and Reset Control
000 = TCtrl: Tslot1 (default)
001 = TCtrl: Tslot2
010 = TCtrl: Tslot3
D[2:0] TS_RST_MODE[2:0] 011 = TCtrl: Tslot4
100 = Do Nothing (bit cleared)
000
101 = Reset Registers Only
110 = Reset Main Digital Only
111 = Reset Complete Chip
NOTE:
1. The device goes into shutdown mode or sleep mode with a typically 600μs delay after the last SDA falling edge.
SG Micro Corp
www.sg-micro.com
JUNE 2018
8
Automatic Blink Mode,
SGM31324
RGB LED Driver withI2C Interface
REGISTER DESCRIPTION (continued)
REG1
Table 3. REG1 Register Details
BITS
BIT NAME
DESCRIPTION
PORV
0 = a logarithmic-like S ramp-up and ramp-down curve. (default)
1 = a simple linear up and down curve.
Flash Period Setting
0000000 = 0.128s (default)
0000001 = 0.384s
D[7]
RAMP_LINE
0
0000010 = 0.512s
0000011 = 0.640s
0000100 = 0.768s
0000101 = 0.896s
0000110 = 1.024s
0000111 = 1.152s
0001000 = 1.28s
0001001 =1.408s
0001010 =1.536s
0001011 =1.664s
0001100 =1.792s
0001101 =1.92s
……
D[6:0] FLASH_PERIOD[6:0] 1101111 = 14.46s
1110000 = 14.59s
0000000
1110001 = 14.72s
1110010 = 14.85s
1110011 = 14.98s
1110100 = 15.10s
1110101 = 15.23s
1110110 = 15.36s
1110111 = 15.49s
1111000 = 15.62s
1111001 = 15.74s
1111010 = 15.87s
1111011 = 16.0s
1111100 = 16.13s
1111101 = 16.26s
1111110 = 16.38s
1111111 = 16.51s
SG Micro Corp
www.sg-micro.com
JUNE 2018
9
Automatic Blink Mode,
SGM31324
RGB LED Driver withI2C Interface
REGISTER DESCRIPTION (continued)
REG2
Table 4. REG2 Register Details
BITS
BIT NAME
DESCRIPTION
Percentage of Period Setting for Flash ON Timer 1
PORV
00000000 = 0.0%
00000001 = 0.4%
00000010 = 0.8%
00000011 = 1.2%
00000100 = 1.6%
00000101 = 2.0%
00000110 = 2.3%
00000111 = 2.7%
00001000 = 3.1%
00001001 = 3.5%
00001010 = 3.9%
00001011 = 4.3%
00001100 = 4.7%
00001101 = 5.1%
……
11101111 = 93.4%
11110000 = 93.8%
11110001 = 94.1%
11110010 = 94.5%
11110011 = 94.9%
11110100 = 95.3%
11110101 = 95.7%
11110110 = 96.1%
11110111 = 96.5%
11111000 = 96.9%
11111001 = 97.3%
11111010 = 97.7%
11111011 = 98.0%
11111100 = 98.4%
11111101 = 98.8%
11111110 = 99.2%
11111111 = 99.6%
D[7:0] PWM1_TM_PER[7:0]
10000001
ON Timer 1 = the corresponding flash period × the corresponding percentage of period
For example, if REG1 = 03h and REG2 = 05h, ON Timer 1 = 0.64s × 2% = 12.8ms
SG Micro Corp
www.sg-micro.com
JUNE 2018
10
Automatic Blink Mode,
SGM31324
RGB LED Driver withI2C Interface
REG3
Table 5. REG3 Register Details
BITS
BIT NAME
DESCRIPTION
Percentage of Period Setting for Flash ON Timer 2
PORV
00000000 = 0.0%
00000001 = 0.4% (default)
00000010 = 0.8%
00000011 = 1.2%
00000100 = 1.6%
00000101 = 2.0%
00000110 = 2.3%
00000111 = 2.7%
00001000 = 3.1%
00001001 = 3.5%
00001010 = 3.9%
00001011 = 4.3%
00001100 = 4.7%
00001101 = 5.1%
……
11101111 = 93.4%
11110000 = 93.8%
11110001 = 94.1%
11110010 = 94.5%
11110011 = 94.9%
11110100 = 95.3%
11110101 = 95.7%
11110110 = 96.1%
11110111 = 96.5%
11111000 = 96.9%
11111001 = 97.3%
11111010 = 97.7%
11111011 = 98.0%
11111100 = 98.4%
11111101 = 98.8%
11111110 = 99.2%
11111111 = 99.6%
D[7:0] PWM2_TM_PER[7:0]
00000001
ON Timer 2 = the corresponding flash period × the corresponding percentage of period
For example, if REG1 = 03h and REG3 = 05h, ON Timer 2 = 0.64s × 2% = 12.8ms
REG4
Table 6. REG4 Register Details
BITS
BIT NAME
DESCRIPTION
PORV
D[7]
Reserved
Reserved
1
Device Enable
It is not restricted by EN logic state.
D[6]
DEV_EN
0 = Disabled. All LEDs are turned off. (default)
0
1 = Enabled. Turn on LEDs according to the LED mode setting, exclusive of automatic blink
mode.
LED3 Mode Setting
00 = Always OFF (default)
D[5:4]
D[3:2]
D[1:0]
LED3_EN_TM[1:0]] 01 = Always ON
10 = PWM1
00
00
10
11 = PWM2
LED2 Mode Setting
00 = Always OFF (default)
01 = Always ON
10 = PWM1
11 = PWM2
LED1 Mode Setting
00 = Always OFF
01 = Always ON
10 = PWM1 (default)
11 = PWM2
LED2_EN_TM[1:0]
LED1_EN_TM[1:0]
SG Micro Corp
www.sg-micro.com
JUNE 2018
11
Automatic Blink Mode,
SGM31324
RGB LED Driver withI2C Interface
REGISTER DESCRIPTION (continued)
REG5
Table 7. REG5 Register Details
BITS
BIT NAME
DESCRIPTION
PORV
tRISE Time Setting
FAC is defined as the corresponding scaling factor setting value of TM_SCAL[1:0]. FAC can be set to
1, 2, 4, or 1/8. Only one scaling register is for both rise and fall time.
0000 = 1.5ms
0001 = 96ms × FAC
0010 = 192ms × FAC
0011 = 288ms × FAC
0100 = 384ms × FAC
0101 = 480ms × FAC
0110 = 576ms × FAC
0111 = 672ms × FAC
1000 = 768ms × FAC
1001 = 864ms × FAC
1010 = 960ms × FAC
1011 = 1056ms × FAC
1100 = 1152ms × FAC
1101 = 1248ms × FAC
1110 = 1344ms × FAC
1111 = 1440ms × FAC
D[7:4] RISE_TM[3:0]
0000
For example, if RISE_TM[3:0] = 0100 and TM_SCAL[1:0] = 00, so FAC = 1, tRISE = 384ms × 1 = 384ms.
tFALL Time Setting
FAC is defined as the corresponding scaling factor setting value of TM_SCAL[1:0]. FAC can be set to
1, 2, 4, or 1/8. Only one scaling register is for both rise and fall time.
0000 = 1.5ms
0001 = 96ms × FAC
0010 = 192ms × FAC
0011 = 288ms × FAC
0100 = 384ms × FAC
0101 = 480ms × FAC
0110 = 576ms × FAC
FALL_TM[3:0] 0111 = 672ms × FAC
D[3:0]
0000
1000 = 768ms × FAC
1001 = 864ms × FAC
1010 = 960ms × FAC
1011 = 1056ms × FAC
1100 = 1152ms × FAC
1101 = 1248ms × FAC
1110 = 1344ms × FAC
1111 = 1440ms × FAC
For example, if FALL_TM[3:0] = 0100 and TM_SCAL[1:0] = 00, so FAC = 1, tRISE = 384ms × 1 = 384ms.
SG Micro Corp
www.sg-micro.com
JUNE 2018
12
Automatic Blink Mode,
SGM31324
RGB LED Driver withI2C Interface
REGISTER DESCRIPTION (continued)
REG6
Table 8. REG6 Register Details
BITS
BIT NAME
DESCRIPTION
PORV
LED1 Current Setting
00000000 = 0.125ms
00000001 = 0.25ms
00000010 = 0.38ms
00000011 = 0.50ms
……
01001111 = 10.00ms
01010000 = 10.13ms
……
10011111 = 20.00ms
10100000 = 20.13ms
……
D[7:0]
I_LED1[7:0]
00111111
10111110 = 23.88ms
10111111 = 24.00ms
11000000 = 24.00ms
……
11111110 = 24.00ms
11111111 = 24.00ms
REG7
Table 9. REG7 Register Details
BITS
BIT NAME
DESCRIPTION
PORV
LED2 Current Setting
00000000 = 0.125ms
00000001 = 0.25ms
00000010 = 0.38ms
00000011 = 0.50ms
……
01001111 = 10.00ms
01010000 = 10.13ms
……
10011111 = 20.00ms
10100000 = 20.13ms
……
D[7:0]
I_LED2[7:0]
10011111
10111110 = 23.88ms
10111111 = 24.00ms
11000000 = 24.00ms
……
11111110 = 24.00ms
11111111 = 24.00ms
SG Micro Corp
www.sg-micro.com
JUNE 2018
13
Automatic Blink Mode,
SGM31324
RGB LED Driver withI2C Interface
REGISTER DESCRIPTION (continued)
REG8
Table 10. REG8 Register Details
BITS
BIT NAME
DESCRIPTION
PORV
LED3 Current Setting
00000000 = 0.125ms
00000001 = 0.25ms
00000010 = 0.38ms
00000011 = 0.50ms
……
01001111 = 10.00ms
01010000 = 10.13ms
……
10011111 = 20.00ms
10100000 = 20.13ms
……
D[7:0]
I_LED3[7:0]
10011111
10111110 = 23.88ms
10111111 = 24.00ms
11000000 = 24.00ms
……
11111110 = 24.00ms
11111111 = 24.00ms
REG9
Table 11. REG9 Register Details
BITS
D[7]
BIT NAME
AUTO_ST
Reserved
DESCRIPTION
PORV
1
Start Automatic Blink Mode (Read Only)
1 = Start Automatic Blink Mode
D[6:1]
Reserved. D[2:1] bits should be set to 11.
010111
Enable Automatic Blink Mode
0 = Disabled
D[0]
1
AUTO_EN
1 = Enabled (default)
REVISION HISTORY
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
JUNE 2018 ‒ REV.A to REV.A.1
Added package thermal resistance......................................................................................................................................................................2
Changes from Original (JULY 2017) to REV.A
Changed from product preview to production data.............................................................................................................................................All
SG Micro Corp
www.sg-micro.com
JUNE 2018
14
PACKAGE INFORMATION
PACKAGE OUTLINE DIMENSIONS
UTDFN-1.5×1.5-8L
e
N5
N8
E2
D2
k
E1
D1
D
E3
N4
N1
b
L
TOP VIEW
BOTTOM VIEW
0.40
1.2
1.10
0.7
A
A1
A2
SIDE VIEW
0.25
0.45
Dimensions
In Millimeters
Dimensions
In Inches
Symbol
MIN
MAX
0.500
0.050
MIN
MAX
0.020
0.002
A
A1
A2
D
0.400
0.000
0.016
0.000
0.127 REF
0.200 REF
0.005 REF
0.008 REF
1.450
0.600
1.550
0.800
0.057
0.024
0.061
0.031
D1
D2
E
1.450
1.100
1.550
1.300
0.057
0.043
0.061
0.051
E1
E2
E3
k
0.050 REF
0.200 REF
0.400 BSC
0.002 REF
0.008 REF
0.016 BSC
1.200
0.150
0.150
1.400
0.250
0.250
0.047
0.006
0.006
0.055
0.010
0.010
b
e
L
SG Micro Corp
www.sg-micro.com
TX00130.000
PACKAGE INFORMATION
TAPE AND REEL INFORMATION
REEL DIMENSIONS
TAPE DIMENSIONS
P2
P0
W
Q2
Q4
Q2
Q4
Q2
Q4
Q1
Q3
Q1
Q3
Q1
Q3
B0
Reel Diameter
P1
A0
K0
Reel Width (W1)
DIRECTION OF FEED
NOTE: The picture is only for reference. Please make the object as the standard.
KEY PARAMETER LIST OF TAPE AND REEL
Reel Width
Reel
Diameter
A0
B0
K0
P0
P1
P2
W
Pin1
Package Type
W1
(mm)
(mm) (mm) (mm) (mm) (mm) (mm) (mm) Quadrant
UTDFN-1.5×1.5-8L
7″
9.0
1.70
1.70
0.75
4.0
4.0
2.0
8.0
Q1
SG Micro Corp
TX10000.000
www.sg-micro.com
PACKAGE INFORMATION
CARTON BOX DIMENSIONS
NOTE: The picture is only for reference. Please make the object as the standard.
KEY PARAMETER LIST OF CARTON BOX
Length
(mm)
Width
(mm)
Height
(mm)
Reel Type
Pizza/Carton
7″ (Option)
7″
368
442
227
410
224
224
8
18
SG Micro Corp
www.sg-micro.com
TX20000.000
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明