LQ201U1LW01 [SHARP]

TFT-LCD Module; TFT -LCD模组


型号：	LQ201U1LW01
厂家：	SHARP ELECTRIONIC COMPONENTS
描述：	TFT-LCD Module TFT -LCD模组显示器光电 CD
文件：	总26页 (文件大小：471K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

LQ201U1LW01

TFT-LCD Module

(Model Number: LQ201U1LW01)

Specifications

Spec No.: LD-14115

Dated: May 29, 2002

PREPARED BY :

APPROVED BY :

DATE

SPEC No. LD-14115

FILE No.

ISSUE : Feb.25.2002

PAGE : 24 pages

TFT LCD DEVELOPMENT GROUP

SHARP CORPORATION

APPLICABLE GROUP

TFT Liquid Crystal Display

Group

SPECIFICATION

DEVICE SPECIFICATION

TFT-LCD Module

MODEL No.

LQ201U1LW01

□ CUSTOMER'S APPROVAL

DATE

PRESENTED

M.TAKEDA

Department General Manager

Development Engineering Department 2

AVC Liquid Crystal Display Division

AVC Liquid Crystal Display Group

SHARP Corporation

RECORDS OF REVISION

LQ201U1LW01

SPEC No.

DATE

SUMMARY

NOTE

REVISED

No. PAGE

LD-14115

Feb. 25. 2002

1 st Issue

LD-14115-1

1. Application

This specification applies to the color 20.1 UXGA TFT-LCD module LQ201U1LW01.

◎These specification sheets are the proprietary product of SHARP CORPORATION(”SHARP) and include

materials protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in

any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express

written permission of SHARP.

◎The device listed in these specification sheets was designed and manufactured for use in OA equipment.

◎In case of using the device for applications such as control and safety equipment for transportation(aircraft,

trains, automobiles, etc. ), rescue and security equipment and various safety related equipment which require

higher reliability and safety, take into consideration that appropriate measures such as fail-safe functions and

redundant system design should be taken.

◎In case of using the device for equipment that requires an extreme level ofꢀreliability,ꢀsuch as aerospace

applications, telecommunication equipment(trunk lines),ꢀnuclear power control equipment and medical or

other equipment for life support,ꢀcontact and consult with a SHARP sales representative.

◎SHARP assumes no responsibility for any damage resulting from the use of the device which does not comply

with the instructions and the precautions specified in these specification sheets.

◎Contact and consult with a SHARP sales representative for any questions about this device.

2. Overview

This module is a color active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor).

It is composed of a color TFT-LCD panel, driver ICs, control circuit, power supply circuit and a back light unit.

Graphics and texts can be displayed on a 1600×3×1200 dots panel with about 16 million colors by supplying 48

bit data signals(8bit×2pixel×RGB) , two display enable signals, two dot clock signals, +12V DC supply

voltages for TFT-LCD panel driving and supply voltage for back light.

It is a wide viewing-angle-module (Vertical viewing angle:170°Horizontal viewing angle:170°,CR≧10).

LD-14115-2

3. Mechanical Specifications

Parameter

Specifications

Unit

Display size

51 (Diagonal)

20.1 (Diagonal)

Inch

408.0 (H)×306.0 (V)

1600 (H)×1200 (V)

(1 pixel＝R＋G＋B dots)

0.255(H)×0.255 (V)

R,G,B vertical stripe

Normally black

Active area

Pixel format

Pixel

Pixel pitch

Pixel configuration

Display mode

436(W)×335 (H)×27.5 (D)

3.8ꢀ(MAX)

Unit outline dimensions *1

Mass

Surface treatment

Anti-glare And hard-coating 2H

*1.Note: excluding back light cables.

The thickness of module (D) doesn’t contain the projection.

Outline dimensions are shown in Fig.1.

LD-14115-3

4. Input Terminals

4-1. TFT-LCD panel driving

CN7A,CN7B (Interface signals and +12VDC power supply)

Using connectors ：DF19G-20P-1H (Hirose Electric Co., Ltd.)

Corresponding connectors ：DF19G-20S-1C (Hirose Electric Co., Ltd.)

DF19G-20S-1F (Hirose Electric Co., Ltd.)

Using LVDS receiver：Contained in a control IC

Corresponding LVDS transmitter：THC63LVDM83R(Thine) or compatible

CN７A

Pin No.

Symbol

Vcc

Function

Remark

+12V power supply

Gnd

Vss

Gnd

RAIN0-

Negative (-) LVDS differential data input (A port)

LVDS

RAIN0+ ꢀPositive (+) LVDS differential data input (A port)

Vss

Gnd

RAIN1-

Negative (-) LVDS differential data input (A port)

LVDS

RAIN1+ ꢀPositive (+) LVDS differential data input (A port)

Vss

RAIN2-

Gnd

Negative (-) LVDS differential data input (A port)

LVDS

RAIN2+ ꢀPositive (+) LVDS differential data input (A port)

Vss

CKAIN-

CKAIN+ ꢀPositive (+) LVDS differential clock input (A port)

Vss

RAIN3-

RAIN3+ ꢀPositive (+) LVDS differential data input (A port)

Vss

BLON

Gnd

Negative (-) LVDS differential clock input (A port)

LVDS

Gnd

Negative (-) LVDS differential data input (A port)

LVDS

Gnd

Back light ON signal (output) 【Note1】

Pull Up

【Note1】BLON:It change from L to H at 7 frames after Vcc ON.

CN７B

Pin No.

Symbol

Vcc

Function

Remark

+12V power supply

Gnd

Vss

Gnd

RBIN0-

Negative (-) LVDS differential data input (B port)

LVDS

RBIN0+ ꢀPositive (+) LVDS differential data input (B port)

Vss

Gnd

RBIN1-

Negative (-) LVDS differential data input (B port)

LVDS

RBIN1+ ꢀPositive (+) LVDS differential data input (B port)

Vss

RBIN2-

Gnd

Negative (-) LVDS differential data input (B port)

LVDS

RBIN2+ ꢀPositive (+) LVDS differential data input (B port)

Vss

CKBIN-

CKBIN+ ꢀPositive (+) LVDS differential clock input (B port)

Vss

RBIN3-

RBIN3+ ꢀPositive (+) LVDS differential data input (B port)

Vss

SELLVDS

Gnd

Negative (-) LVDS differential clock input (B port)

LVDS

Gnd

Negative (-) LVDS differential data input (B port)

LVDS

Gnd

Select LVDS data order 【Note2】

Pull Up

【Note2】This module has dual pixel port to receive dual pixel data at the same time . A port receives first

pixel data and B port receives second pixel data in dual pixel data.

LD-14115-4

ꢀ

ꢀ【Note2】SELLVDS(Thine:THC63LVDM83R)

Transmitter

SELLVDS

R0(LSB)

Pin No

Data

TA0

TA1

TA2

TA3

TA4

TA5

TA6

TB0

TB1

TB2

TB3

TB4

TB5

TB6

TC0

TC1

TC2

TC3

TC4

TC5

TC6

TD0

TD1

TD2

TD3

TD4

TD5

TD6

R7(MSB)

G0(LSB)

G7(MSB)

B0(LSB)

B7(MSB)

(NA)

(RSV1)

R0(LSB)

G0(LSB)

B0(LSB)

(NA)

(RSV1)

R7(MSB)

G7(MSB)

B7(MSB)

(NA)

LD-14115-5

4-2 Interface block diagram

Using receiver：Contained in a control IC.

Corresponding Transmitter：THC63LVDM83R(THine electronics),DS90C383,DS90C383A(National semiconductor)

（Computer side）

(TFT-LCD side)

RAIN0+(5)

RA0～RA7

GA0～GA7

BA0～BA7

RAIN0-(6)

GA0～GA7

RAIN1+(8)

RAIN1-(9)

RAIN2+(11)

RAIN2-(12)

BA0～BA7

RAIN3+(17)

RAIN3-(18)

DEA

CLK

DEA

CLK

RACLKIN+(14)

RACLKIN-(15)

PLL

A Port

B Port

RBIN0+(5)

RBIN0-(6)

RB0～RB7

GB0～GB7

BB0～BB7

RB0～RB7

GB0～GB7

BB0～BB7

RBIN1+(8)

RBIN1-(9)

RBIN2+(11)

DEB

TxIN18~20

RBIN2-(12)

RBIN3+(17)

DEB

RBIN3-(18)

RBCLKIN+(14)

RBCLKIN-(15)

PLL

LD-14115-6

< SELLVDS= Low >

1 cycle

CKAIN+

CK^AIN-

RAIN0+

RAIN0-

RA1

GA2

BA3

RA7

RA0

GA1

BA2

RA6

GA0

BA1

DEA

RA5

BA0

RA4

GA5

RA3

GA4

BA5

GA7

RA2

GA3

BA4

GA6

RA1

GA2

BA3

RA7

RA0

GA1

BA2

RA6

GA0

RAIN1+

RAIN1-

BA1

DEA

RAIN2+

RAIN2-

RAIN3+

RAIN3-

BA7

BA6

Tcsq

CKBIN-

CKBIN+

RBIN0+

RBIN0-

RB1

GB2

BB3

RB7

RB0

GB1

BB2

RB6

GB0

BB1

DEB

RB5

BB0

RSV1

BB7

RB4

RB3

GB4

BB5

GB7

RB2

GB3

BB4

GB6

RB1

GB2

BB3

RB7

RB0

GB1

BB2

RB6

GB0

BB1

DEB

RBIN1+

RBIN1-

GB5

RBIN2+

RBIN2-

RBIN3+

RBIN3-

BB6

DE: Display Enable

RSV1: Reserve (Fixed GND)

NA: Not Available

LD-14115-7

< SELLVDS= High >

1 cycle

CKAIN+

CKAIN-

RAIN0+

RAIN0-

RA3

GA4

BA5

RA1

RA2

GA3

BA4

RA0

GA2

BA3

DEA

RA7

BA2

RA6

GA7

RA5

GA6

BA7

GA1

RA4

GA5

BA6

GA0

RA3

GA4

BA5

RA1

RA2

GA3

BA4

RA0

GA2

RAIN1+

RAIN1-

BA3

DEA

RAIN2+

RAIN2-

RAIN3+

RAIN3-

BA1

BA0

Tcsq

CKBIN-

CKBIN+

RBIN0+

RBIN0-

RB3

GB4

BB5

RB1

RB2

GB3

BB4

RB0

GB2

BB3

DEB

RB7

BB2

RSV1

BB1

RB6

RB5

GB6

BB7

GB1

RB4

GB5

BB6

GB0

RB3

GB4

BB5

RB1

RB2

GB3

BB4

RB0

GB2

BB3

DEB

RBIN1+

RBIN1-

GB7

RBIN2+

RBIN2-

RBIN3+

RBIN3-

BB0

DE: Display Enable

RSV1: Reserve (Fixed GND)

NA: Not Available

LD-14115-8

4-2. Back light driving

CN 1, 2, 3 (Upside)

CN 4, 5, 6 (Downside)

The module-side connector

The user-side connector

BHSR－02VS－01

SM02B－BHSS－1－TB

Function

(JST)

Pin no. symbol

I/O

Ｖ_high

Ｖ_low

Power supply (High voltage side)

Power supply (Low voltage side)

1pin

ＣＮ１

ＣＮ２

ＣＮ３

1pin

TFT LCD

1pin

ＣＮ４

ＣＮ５

ＣＮ６

1pin

5. Absolute Maximum Ratings

Parameter

Symbol Condition

Ratings

Unit

Ｖ

Remark

V_I

Ta=25℃

－

－0.3 ～ +3.6

0 ～＋14.0

－25 ～＋60

0 ～＋50

Input voltage

SELLVDS

Ｖ

+12.0V supply voltage

Storage temperature

Vcc

Tstg

℃

【Note1】

－

℃

Operating temperature (Ambient) Topa

【Note1】Humidity：95%RH Max. ( Ta≦40℃ )

Maximum wet-bulb temperature at 39℃ or less. ( Ta>40℃ )

No condensation.

LD-14115-9

6. Electrical Characteristics

6-1. TFT-LCD panel driving

Parameter

Ta＝25℃

Symbol Min.

Typ. Max. Unit

Remark

【Note1】

【Note2】

Vcc

Supply voltage

Vcc

Icc

+11.4 +12.0 +12.6 V

－

Current dissipation

390

－

600

－

Permissive input ripple voltage

Input voltage (Low)

V_RF

V_IL

100 mVp-p

+0.6

+3.3

500

SELLVDS

V_I=GND

V_IH

I_IL

Input voltage (High)

+2.7

－

μA

Input current (Low)

I_IH

－

μA

Input current (High)

100

SELLVDS

V_I=Vcc

V_OL

V_OH

－

Output voltage (Low)

Output voltage (High)

0.4

BLON:I_OL=-1mA

BLON:I_OH=1mA

－

2.4

【Note1】

1）On-off sequences of Vcc and data

Vcc

11.4V

0＜t1≦60ms

DE,CK ,Data

DE,CK,Data

0＜t2≦10ms

1.0V

0≦t3≦1s

t4≧100ms

Vcc

2）Dip conditions for supply voltage

Vmin,Vth=11.4V, 9.6V

1) Vth ≦Vcc＜ Vmin

td≦ 20ms

2) Vcc＜Vth

Vth

Vmin

The LCD module shuts down.

RGB

GS2

RGB RGB

GS254 GS255

【Note2】 Typical current situation : 256-gray-bar pattern

Vcc=+12.0V

....

GS0 GS1

The explanation of each gray scale ,GS,

is described below section 8.

LD-14115-10

6-2. Back light driving

The back light system is an edge-lighting type with six CCFTs (Cold Cathode Fluorescent Tube).

The characteristics of the lamp are shown in the following table.

The value mentioned below is at the case of one CCFT.

CCFT Model Name：KTBE26MSTF‐A424NE209‐Z‐3（STANLEY.ELECTRIC.CO.,LTD）

Parameter

Lamp current range

Lamp voltage

Symbol

I_L

Min.

3.0

Typ.

6.0

790

4.7

Max.

6.5

Unit

mArms

Vrms

Remark

【Note1】

V_L

－

Ta=25℃

Lamp power consumption

Lamp frequency

P_L

【Note2】

F_L

KHz

【Note3】

Kick-off voltage

1,500 Vrms

2,000 Vrms

－

Ta=25℃【Note4】

Ta=0℃【Note4】

Lamp life time

T_L

50,000

Hour

【Note5】

－

【Note1】 A lamp can be light in the range of lamp current shown above.

Maximum rating for current is measured by high frequency current measurement equipment

connected to V_LOWat circuit showed below.

(Note : To keep enough kick-off voltage and necessary steady voltage for CCFT.)

Lamp frequency : 30～70kHz

Ambient temperature : 0～50℃

CN1:1,2,3,4,5,6:

1pin(Vhigh)

Inverter

CN1:1,2,3,4,5,6:

Ａ

～

Module

2pin(Vlow)

【Note2】 Referential data per one CCFT by calculation ( IL × VL ) .

The data doesn’t include loss at inverter .

【Note3】 Lamp frequency of inverter may produce interference with horizontal synchronous frequency, and

this may cause horizontal beat on the display. Therefore, adjust lamp frequency, and keep inverter as far

as from module or use electronic shielding between inverter and module to avoid interference.

【Note4】Kick-off voltage value is described as the index in the state of lamp only.

The kick-off voltage is estimated to be risen up as approx. +200V in the state of module only, and the

further rise up can be seen according to the assembling status of user cabinet.ꢀPlease set the kick-off

voltage of inverter to avoid the lighting failures in the state of operation. Please design the inverter so

that its open output voltage can be connected for more than 1 second to startup. Otherwise, the lamp

may not be turned on. But, please set as 100ms when the ambient luminance around the lamp is more

than 1lux.

【Note5】 Lamp life time is defined as the time when either ① or ② occurs in the continuous operation under

the condition of Ta=25℃ and I_L=6.0 mArms .

① Brightness becomes 50% of the original value under standard condition.

② Kick-off voltage at Ta=0℃ exceeds maximum value,2000Vrms .

《Note》

The performance of the backlight, for example lifetime or brightness, is much influenced by the characteristics

of the DC-AC inverter for the lamp. When you design or order the inverter, please make sure that a poor lighting

caused by the mismatch of the backlight and the inverter (miss-lighting, flicker, etc.) never occurs. When you

confirm it, the module should be operated in the same condition as it is installed in your instrument.

Use the lamp inverter power source incorporating such safeguard as overvoltage / overcurrent protective circuit

or lamp voltage waveform detection circuit, which should have individual control of each lamp.

In case one circuit without such individual control is connected to more than two lamps, excessive current may

flow into one lamp when the other one is not in operation.

Synchronize frequency and phase of two CCFT in the same connector.

Otherwise it may exceed rated voltage of connector.

LD-14115-11

7. Timing characteristics of input signals

7-1-1. Timing characteristics

Parameter

Symbol

1/Tc

Min.

60.0

–4

Typ.

81.0

Max.

85.0

Unit

MHz

Remark

Clock

Frequency

Skew

【Note1】

Tcsq

Data enable Horizontal period

signal

830

1080

13.3

800

1600

－

clock

µs

10.0

800

Horizontal period (High)

THd

800

2000

－

clock

line

【Note2】

Vertical period

1205

12.1

1200

1250

16.7

1200

Vertical period (High)

TVd

1200

line

【Note1】 Lvds (A port)– Lvds (B port) phase difference

【Note2】 In case of using the long vertical period, the deterioration of display quality, flicker etc. may occur.

THd

DEA,DEB

(RA,GA,BA)

1599

1600

(RB,GB,BB)

1600

1200

DEA,DEB

1199

TVd

DEA

DEB

Tcsq

LD-14115-12

7-2 Input Data Signals and Display Position on the screen

Graphics and texts can be displayed on a 1600 × 3× 1200 dots panel with 16M colors by supplying

48 bit data signal (8bit/color [256 gray scales] × 3 × 2 pixels).

RA GA BA RB GB BB

Two pixel-data are sampled at the same time.

DA(1,1)

DB(2,1)

＊DA： RA0～RA7, GA0～GA7, BA0～BA7

＊DB： RB0～RB7, GB0～GB7, BB0～BB7

DA(1,1) DB(2,1)

DA(1,2) DB(2,2)

DA(1,3)

DA(3,1)

DB(1600,1)

ＲＧＢ

DA(1,1200)

DB(1600,1200)

Display position of input data（H,V）

LD-14115-13

8. Input Signals, Basic Display Colors and Gray Scale of Each Color

Data signal

Colors & Gray RA0 RA1 RA2 RA3 RA4 RA5 RA6 RA7 GA0 GA1 GA2 GA3 GA4 GA5 GA6 GA7 BA0 BA1 BA2 BA3 BA4 BA5 BA6 BA7

Gray scale Scale RB0 RB1 RB2 RB3 RB4 RB5 RB6 RB7 GB0 GB1 GB2 GB3 GB4 GB5 GB6 GB7 BB0 BB1 BB2 BB3 BB4 BB5 BB6 BB7

Black

Blue

－

Green

Cyan

Red

Magenta

Yellow

White

Black

ꢀ

GS0

GS1

GS2

ꢁ

Darker

ꢀ

ꢁ

ꢂ

ꢁ

Brighter GS250

ꢂ

GS251

GS252

Red

Black

ꢀ

GS0

GS1

GS2

ꢁ

Darker

ꢀ

ꢁ

ꢂ

ꢁ

Brighter GS250

GS251

Green GS252

ꢂ

Black

ꢀ

GS0

GS1

GS2

ꢁ

Darker

ꢀ

ꢁ

ꢂ

ꢁ

Brighter GS250

ꢂ

GS251

GS252

Blue

0 : Low level voltage,

1 : High level voltage.

Each basic color can be displayed in 256 gray scales from 8 bit data signals. According to the combination of

total 48 bit data signals, the 16-million-color display can be achieved on the screen.

LD-14115-14

9. Optical Characteristics

Parameter

Ta=25℃, Vcc =+12V

Remark

Symbol

θ11

θ12

θ21,θ22

ＣＲ

τd

Condition

Min.

Typ.

Max.

－

Unit

Deg.

Deg

CR≧10

Viewing

Vertical

【Note1,4】

Angle range

－

Horizontal

Deg.

θ=0°

－

Contrast ratio

350

【Note2,4】

【Note3,4】

－

ｍｓ

－

Response

Time

Rise

τr

－

Decay

0.283

0.313

0.343

Chromaticity of

【Note4】

0.329

white

Chromaticity of

red

－

0.299

0.608

0.309

0.250

0.570

0.114

0.057

0.359

0.668

0.369

0.310

0.630

0.174

0.117

－

0.638

0.339

0.280

0.600

0.144

0.087

－

Chromaticity of

green

－

Chromaticity of

blue

－

Luminance of white

Y_L

cd/m²

IL=6.0mA rms

【Note4】

－

180

220

δw

－

White Uniformity

1.25

【Note5】

The measurement shall be executed 30 minutes after lighting at rating.

※

The optical characteristics shall be measured in a dark room or equivalent state with the method

shown in Fig.2 below.

Photodetector

Contrast ratio/Response Time(BM-5A)

Luminance(BM-7)

Chromaticity(SR-1)

Photodetector(EZ-CONTRAST）

４００mm

Field=２°

Center of screen(θ=0°）

Center of screen(θ=0°)

TFT-LCD-Module

Fig2-2 Luminance/Contrast ratio/Response time/Chromaticity

measurement method

Fig2-1 Viewing angle measurement method

Fig2 Optical characteristics measurement method

LD-14115-15

【Note1】Definitions of viewing angle range:

【Note2】Definition of contrast ratio:

The contrast ratio is defined as the following.

Luminance (brightness) with all pixels white

Luminance (brightness) with all pixels black

Contrast Ratio (CR) ＝

【Note3】Definition of response time:

The response time is defined as the following figure and shall be measured by

switching the input signal for "black" and "white".

【Note4】This shall be measured at center of the screen.

【Note5】Definition of white uniformity:

White uniformity is defined as the

following with five measurements

(A～E).

400

800

1200 pixel

300

600

900

pixel

Maximum Luminance of five points (brightness)

Minimum Luminance of five points (brightness)

δw＝

LD-14115-16

10. Handling Precautions

a) Be sure to turn off the power supply when inserting or disconnecting the cable.

b) Be sure to design the cabinet so that the module can be installed without any extra stress such as warp or

twist.

c) Since the front polarize is easily damaged, pay attention not to scratch it.

d) Since long contact with water may cause discoloration or spots, wipe off water drop immediately.

e) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.

f) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. Handle with

care.

g) Since CMOS LSI is used in this module, take care of static electricity and take the human earth into

consideration when handling.

h) Make sure the mounting holes of the module are grounded sufficiently. Take electro-magnetic interference

(EMI) into consideration.

i) The module has some printed circuit boards (PCBs) on the back side. Take care to keep them form any

stress or pressure when handling or installing the module; otherwise some of electronic parts on the PCBs

may be damaged.

j) Observe all other precautionary requirements in handling components.

k) When some pressure is added onto the module from rear side constantly, it causes display non-uniformity

issue , functional defect, etc. So, please avoid such design.

l) If the stress is applied onto the panel under operating conditions, display defects such as black dots may

occur. So, do not press the display with fingers.

To recover this defect, turn off the power supply and restart after several seconds.

11. Packing form

a) Piling number of cartons : maximum 8 cartons

b) Packing quantity in one carton : 2 module

c) Carton size : 592mm(W) × 486mm(H) × 215(D)

d) Total mass of one carton filled with full modules : 10.5kg

e) Packing form is shown in Fig.3

LD-14115-17

12．Reliability test items

No. Test item

Conditions

Ta=60℃

Ta=-25℃

240h

High temperature storage test

Low temperature storage test

High temperature

Ta=40℃ ; 95%RH 240h

& high humidity operation test

High temperature operation test

(No condensation)

Ta=50℃

(The panel temp. must be less than 60℃)

Ta=0℃ 240H

240h

Low temperature operation test

Vibration test

Frequency : 10～57Hz/Vibration width (one side) : 0.075mm

: 58～500Hz/Gravity : 9.8m/s²

Sweep time : 11 minutes

(non- operating)

Test period : 3 hours

(1 hour for each direction of X,Y,Z)

Max. gravity : 490m/s²

Shock test

(non- operating)

Pulse width : 11ms, sine wave

Direction : ±X, ±Y, ±Z,

once for each direction.

【Result Evaluation Criteria】

Under the display quality test conditions with normal operation state, these shall be no change

which may affect practical display function.

LD-14115-18

13．Others

1) Lot No. and indication Bar Code Label:

SHARP

LQ201U1LW01

How to express Lot No.

Model No.

A production year

(the last figures of

the Christian Era)

Bar Code(Lot No.)

Lot No.

Serial No.

23 XXXXXX

MADE IN JAPAN

A production month (1～9,X,Y,Z)

2) Packing Label

ꢀꢀ① Model No. (LQ201U1LW01)ꢀ ② Lot No. (Date)ꢀ ③ Quantity

^{社内品番：}（４Ｓ）LQ201U1LW01

Bar Code（①）

ＬｏｔＮＯ．ꢀꢀ：（１Ｔ）２００２．０３．０１

Bar Code（②）

Ｑｕａｎｔｉｔｙ：（Ｑ）ꢀꢀꢀꢀ２ꢀꢀｐｃｓ

Bar Code（③）

ユーザ品番ꢀꢀꢀ：

シャープ物流用ラベルです。

3) Adjusting volume have been set optimally before shipment, so do not change any adjusted value.

If adjusted value is changed, the specification may not be satisfied.

4) Disassembling the module can cause permanent damage and should be strictly avoided.

5) Please be careful since image retention may occur when a fixed pattern is displayed for a long time.

6) The chemical compound that causes the destruction of ozone layer is not being used.

7) Warning of mercury and material information of LPG(Light Pipe Guide) are labeled on the back of the

module.

MATERIAL INFORMATION

>PLASTIC LIGHT GUIDE:PMMA<

COLD CATHODE FLUORESCENT LAMP IN LCD PANEL

CONTAINS A SMALL AMOUNT OF MERCURY,PLEASE FOLLOW

LOCAL ORDINANCES OR REGULATION FOR DISPOSAL

当該液晶ディスプレイパネルは蛍光管が組み込まれていますので、地方自

冶体の条例、または、規則に従って廃棄ください。

8) When any question or issue occurs, it shall be solved by mutual discussion.

LD-14115-19

14．Carton storage condition

Temperature

0℃ to 40℃

Humidity

95%RH or less

Reference condition : 20℃ to 35℃ , 85%RH or less (summer)

5℃ to 15℃ , 85%RH or less (winter)

・the total storage time (40℃,95%RH) : 240H or less

Sunlight

Be sure to shelter a product from the direct sunlight.

Atmosphere

Harmful gas, such as acid and alkali which bites electronic components and/or

wires, must not be detected.

Notes

Be sure to put cartons on palette or base, don’t put it on floor, and store them with

removing from wall.

Please take care of ventilation in storehouse and around cartons, and control

changing temperature is within limits of natural environment.

1 year

Storage period

LD -14115-20

LD -14115-21

LD -14115-22

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

Suggested applications (if any) are for standard use; See Important Restrictions for limitations on special applications. See Limited

Warranty for SHARP’s product warranty. The Limited Warranty is in lieu, and exclusive of, all other warranties, express or implied.

ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE AND

FITNESS FOR A PARTICULAR PURPOSE, ARE SPECIFICALLY EXCLUDED. In no event will SHARP be liable, or in any way responsible,

for any incidental or consequential economic or property damage.

NORTH AMERICA

EUROPE

JAPAN

SHARP Corporation

SHARP Microelectronics of the Americas

5700 NW Pacific Rim Blvd.

Camas, WA 98607, U.S.A.

Phone: (1) 360-834-2500

Fax: (1) 360-834-8903

SHARP Microelectronics Europe

Division of Sharp Electronics (Europe) GmbH

Sonninstrasse 3

20097 Hamburg, Germany

Phone: (49) 40-2376-2286

Fax: (49) 40-2376-2232

Electronic Components & Devices

22-22 Nagaike-cho, Abeno-Ku

Osaka 545-8522, Japan

Phone: (81) 6-6621-1221

Fax: (81) 6117-725300/6117-725301

www.sharp-world.com

Fast Info: (1) 800-833-9437

www.sharpsma.com

www.sharpsme.com

TAIWAN

SINGAPORE

KOREA

SHARP Electronic Components

(Korea) Corporation

RM 501 Geosung B/D, 541

Dohwa-dong, Mapo-ku

Seoul 121-701, Korea

SHARP Electronic Components

(Taiwan) Corporation

8F-A, No. 16, Sec. 4, Nanking E. Rd.

Taipei, Taiwan, Republic of China

Phone: (886) 2-2577-7341

SHARP Electronics (Singapore) PTE., Ltd.

438A, Alexandra Road, #05-01/02

Alexandra Technopark,

Singapore 119967

Phone: (65) 271-3566

Phone: (82) 2-711-5813 ~ 8

Fax: (82) 2-711-5819

Fax: (886) 2-2577-7326/2-2577-7328

Fax: (65) 271-3855

CHINA

HONG KONG

SHARP Microelectronics of China

(Shanghai) Co., Ltd.

SHARP-ROXY (Hong Kong) Ltd.

3rd Business Division,

28 Xin Jin Qiao Road King Tower 16F

Pudong Shanghai, 201206 P.R. China

Phone: (86) 21-5854-7710/21-5834-6056

Fax: (86) 21-5854-4340/21-5834-6057

Head Office:

17/F, Admiralty Centre, Tower 1

18 Harcourt Road, Hong Kong

Phone: (852) 28229311

Fax: (852) 28660779

www.sharp.com.hk

No. 360, Bashen Road,

Xin Development Bldg. 22

Shenzhen Representative Office:

Room 13B1, Tower C,

Waigaoqiao Free Trade Zone Shanghai

200131 P.R. China

Electronics Science & Technology Building

Shen Nan Zhong Road

Email: smc@china.global.sharp.co.jp

Shenzhen, P.R. China

Phone: (86) 755-3273731

Fax: (86) 755-3273735

LQ201U1LW01 [SHARP]

相关型号：

LQ201U1LW11

LQ201U1LW32

LQ2144

LQ283G1TW11

LQ295T3LZ31

LQ310-14-.1-D

LQ310-14-.3-D

LQ310-16-.1-D

LQ310-16-.3-D

LQ310-18-.01-D

LQ310-18-.3-D

LQ310-20-.1-D