M40S-61A005AA0 [SICK]
MULTIPLE LIGHT BEAM SAFETY DEVICES;型号: | M40S-61A005AA0 |
厂家: | SICK AG |
描述: | MULTIPLE LIGHT BEAM SAFETY DEVICES |
文件: | 总8页 (文件大小:1578K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
M40S-63A105AA0, M40E-63A105RA0
M4000 Area
MULTIPLE LIGHT BEAM SAFETY DEVICES
M40S-63A105AA0, M40E-63A105RA0 | M4000 Area
MULTIPLE LIGHT BEAM SAFETY DEVICES
Ordering information
A
B
C
D
E
F
System part
Sender
Type
Part no.
1200134
1200685
M40S-63A105AA0
M40E-63A105RA0
Receiver
Other models and accessories www.sick.com/M4000_Area
Detailed technical data
Features
0.5 m ... 70 m, configurable
0.5 m ... 20 m
9 m ... 70 m
Scanning range
Low scanning range
Great scanning range
Length of the monitored area
Resolution
H
I
750 mm
80 mm
17 ms
Response time
J
Optical synchronisation
Synchronization
Safety-related parameters
Type
K
L
Type 4 (IEC 61496)
SIL3 (IEC 61508)
SILCL3 (EN 62061)
Safety integrity level
Category 4 (EN ISO 13849)
PL e (EN ISO 13849)
Category
Performance level
M
N
O
P
Q
R
S
T
1.4 * E-08 (EN ISO 13849)
PFHD (mean probability of a dangerous fail-
ure per hour)
20 years (EN ISO 13849)
TM (mission time)
At least one OSSD is in the OFF state.
Safe state in the event of a fault
Functions
Functions
Delivery status
Internal
✔
✔
✔
✔
✔
✔
✔
Restart interlock
Activated
External device monitoring (EDM)
Beam coding
Uncoded
Deactivated
0.5 m ... 20 m
Contamination (OWS)
Sender test
Configurable scanning range
Configurable application diagnostic output
Safe SICK device communication via EFI
2
OPTO-ELECTRONIC PROTECTIVE DEVICES | SICK
Online data sheet | 2017-08-24 18:11:25
Subject to change without notice
M40S-63A105AA0, M40E-63A105RA0 | M4000 Area
MULTIPLE LIGHT BEAM SAFETY DEVICES
Interfaces
System connection
Connection type Hirschmann male connector M26, 12-pin
Permitted cable length
≤ 50 m 1)
Permitted cross-section ≥ 0.75 mm²
PC with CDS (Configuration and Diagnostic Software)
Configuration method
Configuration connection
Connection type Female connector M8, 4-pin
LEDs
Display elements
7-segment display
Fieldbus, industrial network
CANopen, Ethernet, PROFIBUS DP, PROFIBUS PROFIsafe, PROFINET PROFIsafe 2)
Integration via EFI gateways
CANopen, DeviceNet™, EtherCAT®, EtherNet/IP™, Modbus TCP, PROFIBUS DP, PROFINET 3)
Integration via Flexi Soft safety controller
1)
2)
3)
Depending on load, power supply and wire cross-section. The technical specifications must be observed.
For a suitable EFI-gateway see modules and gateways in the accessory section of connection systems.
For additional information on Flexi Soft -> www.sick.com/Flexi_Soft.
Electrical data
Protection class
Supply voltage VS
III (EN 50178)
24 V DC (19.2 V DC ... 28.8 V DC) 1)
≤ 10 % 2)
Residual ripple
≤ 0.2 A: ≤ 0.6 Aꢀ(depending on type)
Power consumption
Safety outputs (OSSD)
2 PNP semiconductors, short-circuit protected, cross-circuit monitored 3)
Type of output
Switching voltage HIGH 24 V DC (VS – 2.25 V DC ... VS)
Switching voltage LOW ≤ 2 V DC
Switching current ≤ 500 mA
Diagnostic outputs
Type of output PNP semiconductor, short-circuit protected
Switching voltage HIGH 24 V DC (VS – 4.2 V DC ... VS)
Switching voltage LOW High resistance
Switching current ≤ 100 mA
1)
The external voltage supply must be capable of buffering brief mains voltage failures of 20 ms as specified in EN 60204-1. Suitable power supplies are available as
accessories from SICK.
2)
Within the limits of V .
S
3)
Applies to the voltage range between –30 V and +30 V.
Mechanical data
Housing cross-section
Housing material
52 mm x 55.5 mm
Aluminum alloy ALMGSI 0.5
Powder coated
Surface treatment
Front screen material
Polycarbonate, scratch-resistant coating
Ambient data
IP65 (EN 60529)
Enclosure rating
2017-08-24 18:11:25 | Online data sheet
Subject to change without notice
OPTO-ELECTRONIC PROTECTIVE DEVICES | SICK
3
M40S-63A105AA0, M40E-63A105RA0 | M4000 Area
MULTIPLE LIGHT BEAM SAFETY DEVICES
–30 °C ... +55 °C
Ambient operating temperature
Storage temperature
Air humidity
A
B
C
D
E
F
–30 °C ... +70 °C
15 % ... 95 %, Non-condensing
5 g, 10 Hz ... 55 Hz (IEC 60068-2-6)
10 g, 16 ms (IEC 60068-2-29)
Vibration resistance
Shock resistance
Other information
Wave length
950 nm
Classifications
27272703
27272703
27272703
27272703
27272703
27272703
27272703
27272703
EC001832
EC001832
46171620
ECl@ss 5.0
ECl@ss 5.1.4
ECl@ss 6.0
ECl@ss 6.2
ECl@ss 7.0
ECl@ss 8.0
ECl@ss 8.1
ECl@ss 9.0
ETIM 5.0
H
I
ETIM 6.0
UNSPSC 16.0901
J
K
L
M
N
O
P
Q
R
S
T
4
OPTO-ELECTRONIC PROTECTIVE DEVICES | SICK
Online data sheet | 2017-08-24 18:11:25
Subject to change without notice
M40S-63A105AA0, M40E-63A105RA0 | M4000 Area
MULTIPLE LIGHT BEAM SAFETY DEVICES
Dimensional drawing (Dimensions in mm (inch))
55.5 (2.19)
52
(2.05)
52
(2.05)
27.5
(1.08)
M4000 Area 60
M4000 Area 80
14
(0.55)
6
(0.24)
10.5
(0.41)
Sliding nut groove for
side mounting
Cable socket M26 with crimp contacts
(for DIN 43651)
2017-08-24 18:11:25 | Online data sheet
Subject to change without notice
OPTO-ELECTRONIC PROTECTIVE DEVICES | SICK
5
M40S-63A105AA0, M40E-63A105RA0 | M4000 Area
MULTIPLE LIGHT BEAM SAFETY DEVICES
Length of the monitored area S
300 (11.81)
L1
L2
A
B
C
D
E
F
387 (15.24)
537 (21.14)
687 (27.05)
837 (32.95)
987 (38.86)
1,137 (44.76)
1,287 (50.67)
1,437 (56.57)
1,587 (62.48)
1,737 (68.39)
1,887 (74.29)
416 (16.38)
566 (22.28)
716 (28.19)
866 (34.09)
1,016 (40.00)
1,166 (45.91)
1,316 (51.81)
1,466 (57.72)
1,616 (63.62)
1,766 (69.53)
1,916 (75.43)
450 (17.72)
600 (23.62)
750 (29.53)
900 (35.43)
1,050 (41.34)
1,200 (47.24)
1,350 (53.15)
1,500 (59.06)
1,650 (64.96)
1,800 (70.87)
Connection diagram
M4000 Area connected to UE10-3OS safety relay
+24 V
H
I
S1
+24 V
Test
n.c.
n.c.
n.c.
n.c.
n.c.
EFIa
EFIb
n.c.
GND
FE
+24 V
RES
1
3
1
5
EDM
EFia
4
6
5
9
EFib
6
10
3
OSSD1
OSSD2
n.c.
7
8
4
1)
11
7
9
J
B1 B3
Y1 13 23 33 41
ADO
RR
10
11
2
8
GND
FE
UE10-3OS
2
FE
FE
H2
H3
B2 B4
Y2 14 24 34 42
M4000S
Area
M4000R
Area
K
L
0 V
E119955/00/2014-07-29
2) PELV
Task
Connection of an M4000 Area multiple light beam safety device to a UE10-3OS safety relay.
Operating mode: with restart interlock and external device monitoring.
Operating characteristics
When the light path is clear and the UE10-3OS is de-energized and functioning correctly, the yellow LED on the receiver and the H3
lamp flash. The system is ready for switch-on and waits for an input signal/switch-on signal. The system is enabled by pressing and
releasing the S1 button. The OSSD1 and OSSD2 outputs are live, the UE10-3OS is switched on. On interruption of one or several of
the light beams, the UE10-3OS is de-energized by the OSSD1 and OSSD2 outputs.
If the optics are dirty, H2 indicator illuminates.
M
N
O
P
Q
R
S
T
Fault analysis
OSSD cross-circuits and short-circuits are detected and lead to the inhibited state (lock-out). The erroneous behavior of the
UE10-3OS will be detected. The shutdown function is retained. On manipulation (e.g., jamming) of the S1 button, the system does
not enable the output current circuits.
Comments
1) Output circuits: These contacts are to be connected to the controller such that, with the output circuit open, the dangerous state
is disabled. For categories 4 and 3, this integration must be dual-channel (x/y paths). Single-channel insertion in the control (z
path) is only possible with a single-channel control and by taking the risk analysis into account.
2) PELV in accordance with the requirements in
EN 60204-1 / 6.4
Take note of the operating instructions of the integrated devices. This applies particularly to the use of configurable functions.
6
OPTO-ELECTRONIC PROTECTIVE DEVICES | SICK
Online data sheet | 2017-08-24 18:11:25
Subject to change without notice
M40S-63A105AA0, M40E-63A105RA0 | M4000 Area
MULTIPLE LIGHT BEAM SAFETY DEVICES
Recommended accessories
Other models and accessories www.sick.com/M4000_Area
Brief description
Type
Part no.
Mounting brackets and plates
4 pieces, Mounting kit 1, mounting bracket, rigid, L-shaped, including fixing screws
BEF-3WNGBAST4
7021352
and washers
Other mounting accessories
2 pieces, Floor stands for the horizontal mounting of the safety light curtains C4000
BEF-3HHOCAST2
2041661
Fusion, Entry/Exit, Palletizer, as well as the multi-beam safety light curtain M4000
Area, for mounting heights of between 70 mm and 780 mm., Includes mounting
bracket
Terminal and alignment brackets
4 pieces, Mounting kit 6, side bracket, rotatable, Zinc diecast
BEF-1SHABAZN4
BEF-2SMGEAKU4
2019506
2030510
4 pieces, Mounting kit 12, rotatable, swivel mount
Plug connectors and cables
Head A: female connector, M26, 12-pin, straight
Head B: cable
Cable: PVC, unshielded, 5 m
DOL-0612G05M075KM0 2022545
DOL-0612G10M075KM0 2022547
DOL-0612G20M075KM0 2022549
DOS-0612G000GA3KM0 6020757
Head A: female connector, M26, 12-pin, straight
Head B: cable
Cable: PVC, unshielded, 10 m
Head A: female connector, M26, 12-pin, straight
Head B: cable
Cable: PVC, unshielded, 20 m
Head A: female connector, M26, 12-pin, straight
Head B: -
Cable: unshielded
Head A: female connector, M26, 12-pin, angled
DOS-0612W000GA3KM0 6020758
Head B: -
Cable: unshielded
Alignment aids
Laser alignment aid for various sensors, laser class 2 (IEC 60825). Do not look into
the beam!
AR60
1015741
4040006
Adapter AR60 for M4000 and M4000 Curtain
AR60 adapter, M4000
2017-08-24 18:11:25 | Online data sheet
Subject to change without notice
OPTO-ELECTRONIC PROTECTIVE DEVICES | SICK
7
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明