AMS001-R [SILICON]
Embedded Bluetooth Low Energy Solutions;型号: | AMS001-R |
厂家: | SILICON |
描述: | Embedded Bluetooth Low Energy Solutions |
文件: | 总29页 (文件大小:1377K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
AMS00x • Embedded Bluetooth Low Energy Solutions
AMS001 / AMS002
Data Sheet
ADS-MS00x-107R • Preliminary Data Sheet
©2014-2015 ACKme Networks. http://ack.me
September 14, 2015
AMS00x • Embedded Bluetooth Low Energy Solution
Disclaimer
Contact
While the information provided in this document is be-
lieved to be accurate, it is under development and
ACKme Networks reserves the right to make changes
without further notice to the product described herein
to improve reliability, function, or design, and makes no
guarantee or warranty concerning the accuracy of said
information, nor shall it be responsible for any loss or
damage of whatever nature resulting from the use of,
or reliance upon, such information. ACKme Networks
makes no warranties of any kind, whether express, im-
plied or arising by custom or course of trade or perfor-
mance, and specifically disclaims the implied warranties
of title, non-infringement, merchantability, or fitness for
a particular purpose.
http://ack.me/contact
About this Data Sheet
This document provides information on the family of
AMS00x Bluetooth Low Energy (Bluetooth Smart) mod-
ules from ACKme Networks.
Organization
This data sheet is organized into the following sections:
Features & Applications
General Description, Section 1
Block Diagram, Section 2
Electrical Specifications, Section 3
Bluetooth RF Specifications, Section 4
Pinout and Signal Descriptions, Section 5
Design Guidelines, Section 6
Regulatory Certification, Section 7
Packaging, Handling & Storage, RoHS, Section 8
Ordering Information, Section 9
Revision History & Glossary, Section 11
No part of this document may be copied, reproduced,
stored in a retrieval system, or transmitted, in any form
or by any means, electronic, mechanical, photographic,
or otherwise, or used as the basis for manufacture or
sale of any items without the prior written consent of
ACKme Networks.
Trademarks
ACKme Networks and the ACKme Networks logo are
trademarks of ACKme Networks. WICED™ is a trade-
mark of Broadcom® Corporation, Inc. Bluetooth® is a
trademark of the Bluetooth SIG. Other trademarks in
this document belong to their respective owners.
Copyright © 2014-2015 ACKme Networks.
All rights reserved.
Document Number: ADS-MS00x-107R
Release Date: September 14, 2015
ADS-MS00x-107R • Preliminary Data Sheet
Page | i
©2014-2015 ACKme Networks. http://ack.me
September 14, 2015
AMS00x Family Data Sheet
Embedded Bluetooth Low Energy Solution
Features
Operational & Radio
Bluetooth Low Energy (Bluetooth Smart) modules
fully certified to meet Bluetooth version 4.1.
Integrated 8 Mbit SPI-serial flash supports firm-
ware updates and multiple on-board applications
On-board PCB-style antenna
Operational voltage : 1.8V - 3.6V
Operational Temperature Range: -30°C to +85°C
Size : 17.6 x 11.4 x 2.4mm (0.70” x 0.45” x 0.10”)
Weight : 0.04 oz (1.2g)
Current consumption @ 3.0V, 25°C
ARM® Cortex™ M3-based microprocessor core
Adaptive Frequency Hopping (AFH)
Programmable RF transmit power control
Operation directly from a battery or mains supply
Small size enables integration into most sensor
products and applications
Secure Over-the-Air (OTA) software update using
industry-standard AES-128 security
Easily integrated into existing or new products us-
ing TruConnect, ACKme’s configurable Bluetooth
Low Energy application (pre-installed on every
module)
-
-
-
Deep Sleep : 1.65µA (typ.)
Sleep : 12 µA
AMS001
. Active Receive : 12.8 mA
. Active Transmit : 10.8 mA
AMS002
. Active Receive : 26.6 mA
. Active Transmit : 22.0 mA
-
RF Transmit Power: +4 dBm (max.)
Receive Sensitivity : -94 dBm
Applications
Health & Fitness
Multiple services including ACKme TruConnect,
Beacon, iBeacon, plus more …
-
-
-
-
-
-
-
Fitness Equipment
Heart rate monitors
Weight scales
Thermometers
Pedometers
Glucose meters
Blood pressure monitoring
Interfaces*
A/D converter: 7 channels with 4 modes providing
variable resolution (10-13 ENOBs), sampling rate
(5.9-187 kHz) and conversion latency (5-171 µs)
USART: 1 x 4-wire up to 1.5 Mbit/s for general use,
1 x 2-wire for in-circuit programming
Retail
-
-
-
Advertising and Beaconing
Proximity detection
Point-of-sale
SPI: 1 x master, 1 x slave at ≤12 Mbit/s
I2C: 1 x I2C master interface up to 1 MHz
GPIO: Up to 12 GPIOs (overlaid with peripherals),
programmable pull-up/pull-down resistors with
16 mA drive strength at 3.3V (2 mA standard).
4 x PWM channels each with a 10-bit counter
clocked at 128 kHz.
Home & Industrial Control and Automation
-
-
-
-
-
-
Appliance control and monitoring
Doors/Window monitoring
Alarms
Wireless cable replacement
Environmental & Energy monitoring
Wireless sensing, remote data logging
Wake-up: Wake from GPIO for ultra-low power
operation.
*Some interfaces share module pins
Consumer
-
Toys
-
Robots
Remote controls
ADS-MS00x-107R • Preliminary Data Sheet
Page | ii
©2014-2015 ACKme Networks. http://ack.me
September 14, 2015
AMS00x • Embedded Bluetooth Low Energy Solution
Contents
1
2
3
General Description ...............................................1
Labeling
and
User
Information
Requirements.......................................................14
RF Exposure ..........................................15
External Antenna..................................15
Further Information..............................15
Block Diagram ........................................................2
Electrical Specifications..........................................3
3.1
Absolute Maximum Ratings............................3
Recommended Operating Conditions ............3
DC Operating Conditions ........................3
Environmental Conditions ......................4
Power Consumption .......................................4
Input/Output Pins...........................................5
ADC Specifications..........................................5
3.2
7.2
Canada..........................................................15
Labeling and User Information
Requirements.......................................................15
External Antenna Types........................16
Further Information..............................16
3.3
3.4
3.5
7.3
Europe ..........................................................17
4
Bluetooth RF Specifications ...................................6
Labeling and User Information
4.1
Summary RF Specifications.............................6
Receiver Specifications...................................6
Transmitter Specifications..............................7
Requirements.......................................................17
External Antenna Requirements ..........17
Further Information..............................17
4.2
4.3
5
6
Pinout and Signal Descriptions ..............................8
7.4
Australia........................................................18
External Antenna Requirements ..........18
Further Information..............................18
New Zealand.................................................19
External Antenna Requirements ..........19
Further Information..............................19
5.1
5.2
Pinout..............................................................8
Pin Description................................................8
Design Guidelines.................................................10
7.5
6.1
Recommended PCB Footprint ......................10
Routing Recommendations ..........................10
Soldering Information...................................11
AMS00x Photograph.....................................11
Application Examples....................................12
UART Application for Configuration and
6.2
6.3
6.4
6.5
8
9
Packaging, Handling & Storage, RoHS .................20
8.1
Packaging......................................................20
Tape and Reel Specifications........................20
Handling & Storage.......................................22
RoHS Directive..............................................22
8.2
8.3
8.4
Streaming.............................................................12
6.6
Operation using TruConnect ........................12
Bootup Configuration ...........................12
Factory Reset ........................................13
Command and Stream Mode ...............13
GPIO Configuration & Usage ................13
Regulatory Certification.......................................14
Ordering Information...........................................23
10 Revision History & Glossary.................................24
10.1 Revision History............................................24
10.2 Glossary ........................................................24
7
7.1
United States ................................................14
ADS-MS00x-107R • Preliminary Data Sheet
Page | iii
©2014-2015 ACKme Networks. http://ack.me
September 14, 2015
General Description, Section 1
AMS00x • Embedded Bluetooth Low Energy Solution
1 General Description
The family of AMS00x ‘Bobcat’ modules from ACKme
Networks is based on an ultra-low power Bluetooth
Low Energy (Bluetooth Smart) SoC from Broadcom Cor-
poration. All modules incorporate serial-flash memory
and a printed antenna to provide a state-of-the-art ful-
ly-certified Bluetooth 4.1 solution.
Each module provides an extensive array of I/O and
peripheral interfaces. The following interfaces are
available, many of which are accessible with I/O multi-
plexing and alternate function capabilities:
7 x A/D converter channels
2 x UART interfaces: 1 x 4-wire, 1 x 2-wire
1 x SPI master, 1 x SPI slave bus
1 x I2C interface
Up to 12 x ultra-low power wake input
32kHz crystal interface
An integrated solution avoids difficult RF layout and
enables designers to rapidly embed Bluetooth Low En-
ergy into virtually any device.
The AMS001 (Low Power) version slashes active power
consumption for applications requiring multi-year bat-
tery life, while the AMS002 (Low Cost) version provides
the lowest cost solution suitable for price sensitive ap-
plications. The modules are 100% footprint compatible.
The module may be powered directly from a battery
supply in the range 1.8-3.6V including 2xAAA, 2xAA, or
a single Lithium coin cell.
Internal power domains are automatically adjusted to
minimize power dissipation based on user activity. Var-
ious power modes, including an ultra-low power deep
sleep mode, are provided to minimize total average
power consumption and maximize battery life.
Modules ship with ACKme TruConnect, an easy-to-use
application enabling control and configuration via
UART-serial and remote terminal interfaces. TruCon-
nect virtually eliminates difficult and time-consuming
software development effort and vastly reduces prod-
uct development cycles.
Custom factory settings may be saved to a non-erasable
area of static memory to enable out-of-the-box custom
product configuration and the ability to return products
incorporating the module to a known factory reset
state.
With dimensions of just 17.6 x 11.4 mm, a wide tem-
perature range, and an ultra-low power version, the
module is suitable for integration into any battery-
powered embedded wireless application.
The module may be woken from deep sleep mode by a
level transition on the GPIO assigned for stream mode
selection. Other GPIOs may be dynamically allocated for
control and status including a BLE connection indicator,
serial bus mode control and status indicator, audible
alerts and factory reset.
The Bluetooth Low Energy SoC from Broadcom is pur-
pose-designed to support the entire spectrum of Blue-
tooth Smart use cases for medical, home automation,
accessory, sensor, retail and wearable market seg-
ments. Superior receive sensitivity, an integrated RF
transmit power amplifier and transmit/receive switch,
along with the on-board antenna, provide extended
range and full compatibility with all Bluetooth 4.1 de-
vices.
An internal 32kHz low-power oscillator is available by
default for non-critical timing requirements. Applica-
tions requiring an accurate real-time clock may connect
an (optional) external 32kHz crystal.
At the heart of all AMS00x modules is a Bluetooth Low
Energy SoC with a high-performance ARM® 32-bit Cor-
tex™-M3 core operating at a frequency of 24 MHz. The
SoC includes is configured to boot applications stored in
the 8 Mbit serial flash memory available on-board the
module.
All versions of the module have Bluetooth BQB SIG cer-
tification, and FCC & IC modular approval for use in the
United States and Canada, and CE approval for use in
Europe and other countries.
The Broadcom BLE SoC supports Adaptive Frequency
Hopping.
ADS-MS00x-107R • Preliminary Data Sheet
Page | 1
©2014-2015 ACKme Networks. http://ack.me
September 14, 2015
Block Diagram, Section 2
AMS00x • Embedded Bluetooth Low Energy Solution
2 Block Diagram
Figure 1 is a block diagram showing the architecture of
AMS00x Bluetooth Low Energy modules. The major
components are a Bluetooth Low Energy SoC from
Broadcom, 24MHz crystal, 8 Mbit serial flash and a PCB-
style antenna. The AMS001 version also includes a high-
efficiency DC-DC switching regulator to significantly re-
duce active mode power consumption.
The 8 Mbit serial flash memory stores the ACKme
TruConnect™ application and user configuration, and
enables secure Over-the-Air (OTA) wireless firmware
updates. The on-board PCB antenna simplifies RF inte-
gration into end products.
An extensive array of analog and digital peripherals in-
cluding ADCs, GPIOs, PWMs and multiple serial inter-
faces such as UART, SPI and I2C are accessible via mod-
ule pins.
The Bluetooth SoC is powered by an ARM Cortex M3-
based processor running at 24 MHz. The SoC is driven
by a 24 MHz crystal, an on-board real-time clock may
be (optionally) enabled by connecting an external
32kHz crystal.
The module is powered by a single-rail battery or mains
supply.
Figure 1. AMS00x Architecture
VDD
32kHz XTAL
Bluetooth
Low Energy
24MHz
SPI
UART
SoC
I2C
8 Mbit
ARM Cortex M3
Serial Flash
ADC
GPIO
PWM
Reset
DC-DC
AMS001
Only
AMS00x
ADS-MS00x-107R • Preliminary Data Sheet
Page | 2
©2014-2015 ACKme Networks. http://ack.me
September 14, 2015
Electrical Specifications, Section 3
AMS00x • Embedded Bluetooth Low Energy Solution
3 Electrical Specifications
3.1 Absolute Maximum Ratings
CAUTION! The absolute maximum ratings in Table 1 and Table 2 indicate levels where permanent damage to the de-
vice can occur, even if these limits are exceeded for only a brief duration. Functional operation is not guaranteed un-
der these conditions. Operation at absolute maximum conditions for extended periods can adversely affect long-
term reliability of the device.
Table 1. Absolute Maximum Voltage Ratings
Symbol
VDDmax
VIO
Ratings
Min.
Max.
3.8
Unit
V
DC supply voltage applied to VDD pin
Voltage on input or output pin
GND - 0.3
GND - 0.3
VDDmax + 0.3
V
Table 2. Absolute Maximum Environmental Ratings
Characteristic
Storage Temperature
Relative Humidity
Note
Min.
-40
–
Max.
+125
65
Unit
°C
–
Non-condensing (storage)
%
3.2 Recommended Operating Conditions
Functional operation is not guaranteed outside the limits shown in Table 3 and Table 4, and operation outside these
limits for extended periods can adversely affect long-term reliability of the device.
DC Operating Conditions
Table 3. Recommended DC Operating Conditions
Symbol
Ratings1
Min.
Typical
Max.
Unit
VDD
DC supply voltage applied to VDD pin
On-board serial flash read-only
On-board serial flash read and write
On-board serial flash at power-on
1.8
2.1
2.252
–
–
–
3.63
3.63
3.63
V
V
V
Notes:
1. Overall performance degrades beyond minimum and maximum supply voltages.
2. The module may fail to boot if this condition is not met when power is initially applied.
ADS-MS00x-107R • Preliminary Data Sheet
Page | 3
©2014-2015 ACKme Networks. http://ack.me
September 14, 2015
Electrical Specifications, Section 3
AMS00x • Embedded Bluetooth Low Energy Solution
Environmental Conditions
Table 4. Recommended Environmental Conditions
Characteristic
Ambient Temperature
Relative Humidity
Note
Min.
-30
–
Max.
+85
85
Unit
°C
Non-condensing (operating)
%
3.3 Power Consumption
The AMS00x automatically adjusts power dissipation based on user activity to minimize power usage. The power
consumption in each state, and for each version of the module, is specified in Table 5.
Table 5. Power Consumption (3.0V, 25°C)
Operational State Note
Typical
1.65
Unit
µA
Deep sleep1
BLE Chip (0.65 µA) + Serial Flash (1 µA)
Sleep
Wake in <5ms
12.0
µA
AMS001
Active Receive
Receiver enabled and operating at 100% duty cycle
12.8
10.8
mA
mA
Active Transmit2 Transmitter enabled and operating at 100% duty cycle
AMS002
Active Receive
Receiver enabled and operating at 100% duty cycle
26.6
22.0
mA
mA
Active Transmit2 Transmitter enabled and operating at 100% duty cycle
Notes:
1. Requires 10K pullup resistor on module pin 6. See 6.5.1, UART Application for Configuration and Streaming
2. RF transmit power = 0dBm
ADS-MS00x-107R • Preliminary Data Sheet
©2014-2015 ACKme Networks. http://ack.me
Page | 4
September 14, 2015
Electrical Specifications, Section 3
AMS00x • Embedded Bluetooth Low Energy Solution
3.4 Input/Output Pins
All digital I/O pins have a maximum input voltage rating of VSS-0.3V to VDD+0.3V.
The maximum supply voltage is 3.63V.
Consequently, digital I/O pins are NOT +5V tolerant.
Table 6. Digital I/O Pin Levels
Symbol
VIL
Description
Min.
Typical
Max.
0.4
–
Unit
V
Input low voltage
Input high voltage
Output low voltage1
Output high voltage1
–
–
–
–
–
VIH
0.75 x VDD
–
V
VOL
0.4
–
V
VOH
VDD – 0.4
V
Notes:
1. At the specified drive current for the pin.
3.5 ADC Specifications
Table 7. ADC Specifications (@ 25°C)
Parameter
Symbol Conditions
Min.
Typ.
Max.
–
Unit
–
Input Channels
–
fch
Vinp
–
–
–
8
Channel Switching Rate
Input signal range
Reference settling time
Input resistance
133.33
–
kch/s
V
0
–
–
3.63
–
7.5
–
µS
Rin
Cin
Effective, single ended
500
–
–
kΩ
pF
Input capacitance
Conversion rate
–
5
Rc
5.859
5.35
10
–
–
187
170.7
13
–
kHz
µS
Conversion time
Tc
–
Effective Number of Bits
Abs. Voltage Meas. Error
Current
ENOB
–
–
bits
%
±2
–
I
–
1
mA
nA
µS
Leakage Current
Ileakage
Tpup
INL
–
–
100
200
1
Power-up time
–
–
Integral nonlinearity
Differential nonlinearity
LSBs at the 10-bit level
LSBs at the 10-bit level
-1
-1
–
LSB
LSB
DNL
–
1
ADS-MS00x-107R • Preliminary Data Sheet
Page | 5
©2014-2015 ACKme Networks. http://ack.me
September 14, 2015
Bluetooth RF Specifications, Section 4
AMS00x • Embedded Bluetooth Low Energy Solution
4 Bluetooth RF Specifications
Unless otherwise stated, the specifications in this section apply when the operating conditions are within the limits
specified in Section 3.2, Recommended Operating Conditions. Functional operation outside these limits is not guar-
anteed.
All specifications are measured with a coax pigtail soldered to the PCB antenna feed point, with VDD = 3.0V and at a
room temperature of 25°C.
4.1 Summary RF Specifications
Table 8. Summary RF Specifications
Feature Supported
Bluetooth Standard
Frequency Band
Description
Version 4.1
2.400 GHz – 2.500 GHz
Channels (2MHz spacing)
3 x Advertising channels @ 2402 / 2426 / 2480 MHz
36 x Data channels
Maximum Raw Data Rate
Maximum Application Data Rate
Modulation Type
1 Mbit/s
0.27 Mbit/s
DSSS: GFSK (modulation index = 0.5)
Maximum RF Input
-10 dBm
Typical Receive Sensitivity
Maximum RF Tx Output Power
Carrier Frequency Accuracy
-94 dBm
+4 dBm
±20 ppm (24 MHz crystal, ±20 ppm stability @ 25°C)
4.2 Receiver Specifications
Table 9. Receiver Performance Specifications
Parameter
Frequency Range
Condition/Notes
Min.
2402
-30
–
Typical
Max.
2480
+85
–
Unit
MHz
°C
–
–
–
Operating Temperature
Receive Sensitivity
–
200 x 37-byte packets with 30.8% PER
-94
–
dBm
dBm
Maximum Receive Level
-10
–
ADS-MS00x-107R • Preliminary Data Sheet
Page | 6
©2014-2015 ACKme Networks. http://ack.me
September 14, 2015
Bluetooth RF Specifications, Section 4
AMS00x • Embedded Bluetooth Low Energy Solution
4.3 Transmitter Specifications
Table 10. Transmitter Performance Specifications
Parameter
Frequency Range
Condition/Notes
Min
2402
-30
–
Typical
Max
2480
+85
–
Unit
MHz
°C
–
–
Operating Temperature
Transmit power2
–
–
–
4.0
2.0
dBm
Transmit power variation
Transmit Power Range
Channel Spacing
Process dependent
–
–
Adjustable via software control
-20
–
4
dBm
MHz
2
–
ADS-MS00x-107R • Preliminary Data Sheet
Page | 7
©2014-2015 ACKme Networks. http://ack.me
September 14, 2015
Pinout and Signal Descriptions, Section 5
AMS00x • Embedded Bluetooth Low Energy Solution
5 Pinout and Signal Descriptions
5.1 Pinout
A top view of the AMS00x pinout is depicted in Figure 2.
All dimensions are in thousands of an inch. A recom-
mended PCB footprint is provided in Section 6.1.
Figure 2. AMS00x Pinout (TOP View – Pins NOT visible from top!)
5.2 Pin Description
Table 11. AMS00x Pin Definitions
Pin
1
Name
Type1 Primary Function
Alternate & Other Function(s)
GND
S
I
Ground
-
-
-
2
PROG_RX
PROG_TX
GPIO_0
PROG RX
PROG TX
Reserved4
3
O
4
I/O
Not available as digital I/O. Reserved for future use as
SPI_MOSI, I2C_SDA
5
GPIO_1
I/O
Reserved4
Not available as digital I/O. Reserved for future use as
SPI_CLK, I2C_SCL
6
7
GPIO_2
GPIO_3
RESET_N
GPIO_4
GPIO_5
I/O
I/O
I
USER TX
SPI_MOSI (Slave), ADC, GPIO
SPI_MISO (Slave), ADC. , GPIO
-
USER_RTS
System Reset
USER_CTS
USER_RX
8
9
I/O
I/O
SPI_CLK (Slave), GPIO
SPI_CS (Slave), GPIO
10
ADS-MS00x-107R • Preliminary Data Sheet
©2014-2015 ACKme Networks. http://ack.me
Page | 8
September 14, 2015
Pinout and Signal Descriptions, Section 5
AMS00x • Embedded Bluetooth Low Energy Solution
Alternate & Other Function(s)
Pin
11
12
13
14
15
16
17
18
19
20
21
Name
Type1 Primary Function
GPIO_6
GPIO_7
GPIO_8
GPIO_9
GPIO_102
GPIO_11
GPIO_12
GPIO_132
GND
I/O
N/C
I/O
I/O
I/O
I/O
I/O
I/O
S
GPIO
Reserved4
SPI_MOSI (Master), FACTORY_RESET3
Reserved. Not available as digital I/O
GPIO
SPI_MISO (Master)
GPIO
SPI_CLK (Master)
GPIO
ADC, PWM
GPIO
ADC, PWM
GPIO
SPI_CS (Master), ADC
GPIO
ADC, PWM, XOSC32_OUT
Ground
GPIO
-
GPIO_142
I/O
S
ADC, PWM, XOSC32K_IN
VDD
VDD
-
-
22-27 GND
S
Ground
Notes:
1. I = Input, O = Output, S = Supply
2. The drive strength of standard GPIOs is 2mA, the drive strength of this GPIO is 16mA.
3. The FACTORY_RESET pin may be moved to a different GPIO, but it may not be de-assigned
4. Connected to SPI serial flash inside the module
ADS-MS00x-107R • Preliminary Data Sheet
Page | 9
©2014-2015 ACKme Networks. http://ack.me
September 14, 2015
Design Guidelines, Section 6
AMS00x • Embedded Bluetooth Low Energy Solution
6 Design Guidelines
6.1 Recommended PCB Footprint
All dimensions in Figure 3 are in thousands of an inch unless otherwise marked.
Figure 3. AMS00x Recommended Footprint (Top)
6.2 Routing Recommendations
When designing a carrier board, the addition of
ground fill directly underneath the module, rather
than signal or power traces, is strongly advised.
265
115
All ground pads adjacent to antenna pins must be
connected to a solid ground plane. Do not route
ANY metal or PCB traces underneath the printed
PCB-antenna!
115
265
Failure to comply with these recommendations will
almost certainly result in degraded performance of
the radio receiver and/or transmitter.
Avoid routing traces not connected to ground under the
vias in the shaded rectangle.
Measurements are in thousandths of an inch.
For optimal range, provide a clearance of 5mm
(0.2”) above, below and to the front and sides of the
antenna end of the module.
ADS-MS00x-107R • Preliminary Data Sheet
Page | 10
©2014-2015 ACKme Networks. http://ack.me
September 14, 2015
Design Guidelines, Section 6
AMS00x • Embedded Bluetooth Low Energy Solution
6.3 Soldering Information
Figure 4. Recommended solder reflow profile
6.4 AMS00x Photograph
Figure 5. AMS00x Photograph (Top)
ADS-MS00x-107R • Preliminary Data Sheet
Page | 11
©2014-2015 ACKme Networks. http://ack.me
September 14, 2015
Design Guidelines, Section 6
AMS00x • Embedded Bluetooth Low Energy Solution
6.5 Application Examples
UART Application for Configuration and Streaming
Follow the schematic in Figure 6 to connect a host MCU UART to the User UART serial interface of the AMS00x mod-
ule. This application enables a host MCU to configure the module using command mode, and transfer data back and
forth to a remote device via the Bluetooth LE wireless interface using stream mode. UART hardware flow control is
not required, but is recommended for streaming continuous data.
Figure 6. Connecting a Host MCU to the AMS001/AMS002 User UART
Note: The 10K pullup resistor on pin 6 allows the module to go to sleep and stay asleep. It also enables sleep current
to be reduced to a typical value of 1.65uA. If pin 6 is not driven high the wake-up circuit may be highly sensitive to
small variations in capacitance or voltage on module pins. Module sleep current may also remain higher, at around
200uA.
settings may be saved/changed as required, Factory
Settings may be saved only once, and Default settings
are hardcoded into the app at compile time and cannot
be changed. Configuration load at boot time occurs in
the following sequence:
6.6 Operation using TruConnect
The information in this section provides a very brief
overview of basic operation using TruConnect. For de-
tailed information, consult the TruConnect Reference
Guide available online at http://truconnect.ack.me
1. User Settings. This configuration is set by a user and
saved by the TruConnect savecommand without
any supplied arguments. User configuration can be
changed at any time, and the configuration is delet-
ed when a factory reset is performed. If no user
configuration is present or it is corrupted then
TruConnect attempts to load the factory settings.
Bootup Configuration
At boot up, TruConnect attempts to load saved configu-
ration settings i.e. the saved state of TruConnect varia-
bles. There are three configuration sets that may be
loaded, depending on the state of the module. User
ADS-MS00x-107R • Preliminary Data Sheet
Page | 12
©2014-2015 ACKme Networks. http://ack.me
September 14, 2015
Design Guidelines, Section 6
AMS00x • Embedded Bluetooth Low Energy Solution
2. Factory Settings. Factory configuration provides a
way to save a configuration at manufacturing time.
Factory settings are saved using the TruConnect
ured), or to simply transition from command mode to
stream mode, use the strcommand.
Once in stream mode, characters received from a host
MCU on the serial interface are automatically transmit-
ted to a remotely connected device via the BLE wireless
interface, and characters received from a remotely
connected device on the BLE wireless interface are
seamlessly transmitted on the serial interface to the
host MCU.
command:
save factory <BD_ADDR>
Save with the lockoption to ensure that factory
settings cannot be overwritten:
save factory <BD_ADDR> lock
CAUTION! The factory configuration cannot be
changed after saving with the lockoption.
If no factory configuration is present or it is corrupt-
ed, then TruConnect loads the basic compile-time
default configuration.
Configuration of the module is also possible using a re-
motely connected application, however if the serial in-
terface is configured to use command mode, remote
applications are forbidden from accessing the com-
mand interface. To grant a remote application access to
the command interface, the serial interface must first
place the module into stream mode to signal that it no
longer requires access to the command parser.
3. Default Settings. The default configuration is a
sane set of defaults that are hardcoded in TruCon-
nect.
Factory Reset
The module may be factory reset with a TruConnect
command, or by asserting the factory reset pin at
bootup.
GPIO Configuration & Usage
The default GPIO configuration of the module is shown
in the following list, obtained by issuing the TruConnect
command sequence get gp u. The User UART, factory
reset and I2C pins are configured by default. All other
pins are unassigned or reserved.
To factory reset via a command, issue:
> fac <BD_ADDR>
To factory reset via the factory reset GPIO:
> get gp u
1. Identify the GPIO used for factory reset by issu-
ing the command to get GPIO usage: get gp u
(the factory reset default is GPIO 6).
!
#
#
#
#
#
#
#
#
#
#
# Description
0 i2c_sda
1 i2c_scl
2 user_tx
3 none
2. Assert a logic 1 (high) on the pin associated
with the factory reset GPIO
3. Assert and de-assert the reset pin to force the
module to reboot
4. Wait at least 10 seconds (the status of factory
reset is printed to the User UART
5. De-assert the factory reset pin
4 none
5 user_rx
6 none,factory
7 reserved
8 none
9 none
# 10 none
# 11 none
# 12 none
# 13 none
# 14 none
Command and Stream Mode
The module boots into serial bus command mode by
default and accepts configuration and control com-
mands via the User UART. Once the configuration is
saved, stream mode may be used to transfer data be-
tween the serial interface and a remote device con-
nected to the Bluetooth LE wireless interface. To toggle
between command mode and stream mode, the GPIO
alternate function mode_sel may be used (if config-
To configure a GPIO pin for use, the pin must be as-
signed a function. A large range of functions is availa-
ble, please refer to the TruConnect reference guide
online (at the following link) for further information:
http://truconnect.ack.me/commands#gfu
ADS-MS00x-107R • Preliminary Data Sheet
Page | 13
©2014-2015 ACKme Networks. http://ack.me
September 14, 2015
Regulatory Certification, Section 7
AMS-00x • Embedded Bluetooth Low Energy Solution
7 Regulatory Certification
The AMS00x family of modules has been certified for
operation in various regulatory domains. This section
outlines certification information specific to the follow-
ing countries and regions:
Labeling and User Information
Requirements
The AMS-00x module has been labelled with a unique
FCC ID number, and if the FCC ID is not visible when the
module is installed inside another device, then the out-
side of the finished product into which the module is
installed must also display a label referring to the en-
closed module. This exterior label can use wording as
follows:
United States
Canada
Europe
Australia
New Zealand
Contains FCC ID: 2ABPY-BB4EA - Model No: AMS001
Contains FCC ID: 2ABPY-0D06E - Model No: AMS002
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause un-
desired operation.
Should you require regulatory certification for the
AMS00x module in a country or region not listed, please
contact your local ACKme Networks sales office or cre-
ate
a
support request via our website at
http://ack.me/contact.
7.1 United States
The ACKme Networks AMS-00x module has received
Federal Communications Commission (FCC) CFR47 Tele-
communications, Part 15 Sub-part C “Intentional Radia-
tors” modular approval in accordance with Part 15.212
Modular Transmitter approval. Modular approval al-
lows the end user to integrate the AMS-00x module
into a finished product without obtaining subsequent
and separate FCC approvals for intentional radiation,
provided no changes or modifications are made to the
module circuitry. Changes or modifications could void
the user’s authority to operate the equipment. The end
user must comply with all of the instructions provided
by the Grantee which indicate installation and/or oper-
ating conditions necessary for compliance.
The user manual for the product should include the fol-
lowing statement:
This equipment has been tested and found to com-
ply with the limits for a Class B digital device, pursu-
ant to part 15 of the FCC Rules. These limits are de-
signed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate ra-
dio frequency energy and if not installed and used in
accordance with the instructions, may cause harm-
ful interference to radio communications. However,
there is no guarantee that interference will not oc-
cur in a particular installation. If this equipment
does cause harmful interference to radio or televi-
sion reception, which can be determined by turning
the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the
following measures:
The finished product is required to comply with all ap-
plicable FCC equipment authorization, regulations, re-
quirements, and equipment functions not associated
with the transmitter module portion. For example,
compliance must be demonstrated to regulations for
other transmitter components within the host product;
to requirements for unintentional radiators (Part 15
Sub-part B “Unintentional Radiators”), such as digital
devices, computer peripherals, radio receivers, etc.; and
to additional authorization requirements for non-
transmitter functions on the transmitter module (i.e.
Verification, or Declaration of Conformity) (e.g., trans-
mitter modules may also contain digital logic functions)
as appropriate.
Reorient or relocate the receiving antenna.
Increase the separation between the equip-
ment and receiver.
Connect the equipment into an outlet on a cir-
cuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV
technician for help.
ADS-MS00x-107R • Preliminary Data Sheet
©2014-2015 ACKme Networks. http://ack.me
Page | 14
September 14, 2015
Regulatory Certification, Section 7
AMS-00x • Embedded Bluetooth Low Energy Solution
Additional information on labeling and user information
requirements for Part 15 devices can be found in KDB
Publication 784748 available at the FCC Office of Engi-
neering and Technology (OET) Laboratory Division
Knowledge Database (KDB) at the following website:
https://apps.fcc.gov/oetcf/kdb/index.cfm
External Antenna
Modular approval in the United States is permitted with
the use of the integrated antenna ONLY. If an external
antenna is used with the AMS-00x module, additional
testing of the end product is needed to meet FCC re-
quirements.
RF Exposure
Further Information
All transmitters regulated by FCC must comply with RF
exposure requirements. OET Bulletin 65, Evaluating
Compliance with FCC Guidelines for Human Exposure to
Radio Frequency Electromagnetic Fields, provides assis-
tance in determining whether proposed or existing
transmitting facilities, operations or devices comply
with limits for human exposure to Radio Frequency (RF)
fields adopted by the Federal Communications Com-
mission (FCC). The bulletin offers guidelines and sugges-
tions for evaluating compliance.
Additional information regarding FCC certification and
use of the AMS-00x module in the United States is
available from the following sources.
Federal Communications Commission (FCC)
http://www.fcc.gov.au
FCC Office of Engineering and Technology (OET)
Laboratory Division Knowledge Database (KDB)
http://apps.fcc.gov/oetcf/kdb/index.cfm
If appropriate, compliance with exposure guidelines for
mobile and unlicensed devices can be accomplished by
the use of warning labels and by providing users with
information concerning minimum separation distances
from transmitting structures and proper installation of
antennas.
7.2 Canada
The AMS-00x module has been certified for use in Can-
ada under Industry Canada (IC) Radio Standards Specifi-
cation (RSS) RSS-210 and RSSGen. Modular approval
permits the installation of a module in a host device
without the need to recertify the device.
The following statement must be included as a CAU-
TION statement in manuals and OEM products to alert
users of FCC RF exposure compliance:
Labeling and User Information
Requirements
To satisfy FCC RF Exposure requirements for mobile
and base station transmission devices, a separation
distance of 20 cm or more should be maintained
between the antenna of this device and persons
during operation. To ensure compliance, operation
at closer than this distance is not recommended.
The antenna(s) used for this transmitter must not
be co-located or operating in conjunction with any
other antenna or transmitter
Labeling Requirements for the Host Device (from Sec-
tion 3.2.1, RSS-Gen, Issue 3, December 2010): The host
device shall be properly labeled to identify the module
within the host device.
The Industry Canada certification label of a module
shall be clearly visible at all times when installed in the
host device, otherwise the host device must be labeled
to display the Industry Canada certification number of
the module, preceded by the words “Contains transmit-
ter module”, or the word “Contains”, or similar wording
expressing the same meaning, as follows:
If the AMS-00x module is used in a portable application
(i.e., the antenna is less than 20 cm from persons dur-
ing operation), the integrator is responsible for per-
forming Specific Absorption Rate (SAR) testing in ac-
cordance with FCC rules 2.1091.
Contains transmitter module IC: 11685A-0D06E
User Manual Notice for License-Exempt Radio Appa-
ratus (from Section 7.1.3 RSS-Gen, Issue 3, December
2010): User manuals for license-exempt radio appa-
ADS-MS00x-107R • Preliminary Data Sheet
Page | 15
©2014-2015 ACKme Networks. http://ack.me
September 14, 2015
Regulatory Certification, Section 7
AMS-00x • Embedded Bluetooth Low Energy Solution
ratus shall contain the following or equivalent notice in
a conspicuous location in the user manual or alterna-
tively on the device or both:
User manuals for transmitters equipped with detach-
able antennas shall also contain the following notice in
a conspicuous location:
This device complies with Industry Canada license-
exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not
cause interference, and (2) this device must accept
any interference, including interference that may
cause undesired operation of the device.
This radio transmitter (identify the device by certifi-
cation number, or model number if Category II) has
been approved by Industry Canada to operate with
the antenna types listed below with the maximum
permissible gain and required antenna impedance
for each antenna type indicated. Antenna types not
included in this list, having a gain greater than the
maximum gain indicated for that type, are strictly
prohibited for use with this device.
Le présent appareil est conforme aux CNR d'Indus-
trie Canada applicables aux appareils radio exempts
de licence. L'exploitation est autorisée aux deux
onditions suivantes: (1) l'appareil ne doit pas
produire de brouillage, et (2) l'utilisateur de l'appa-
reil doit accepter tout brouillage radioélectrique
subi, meme si le brouillage est susceptible d'en
compromettre le fonctionnement.
Le présent émetteur radio (identifier le dispositif
par son numéro de certification ou son numéro de
modèle s'il fait partie du matériel de catégorie I) a
été approuvé par Industrie Canada pour fonctionner
avec les types d'antenne énumérés ci-dessous et
ayant un gain admissible maximal et l'impédance
requise pour chaque type d'antenne. Les types d'an-
tenne non inclus dans cette liste, ou dont le gain est
supérieur au gain maximal indiqué, sont strictement
interdits pour l'exploitation de l'émetteur.
Transmitter Antenna Notification (from Section 7.1.2
RSS-Gen, Issue 3, December 2010): User manuals for
transmitters shall display the following notice in a con-
spicuous location:
Under Industry Canada regulations, this radio
transmitter may only operate using an antenna of a
type and maximum (or lesser) gain approved for the
transmitter by Industry Canada. To reduce potential
radio interference to other users, the antenna type
and its gain should be so chosen that the equivalent
isotropically radiated power (EIRP) is not more than
that necessary for successful communication.
Immediately following the above notice, the manufac-
turer shall provide a list of all antenna types approved
for use with the transmitter, indicating the maximum
permissible antenna gain (in dBi) and required imped-
ance for each.
External Antenna Types
Transmitter Antenna (from Section 7.1.2 RSS-Gen, Issue
3, December 2010):
Conformément à la réglementation d'Industrie Can-
ada, le présent émetteur radio peut fonctionner
avec une antenne d'un type et d'un gain maximal
(ou inférieur) approuvé pour l'émetteur par Indus-
trie Canada. Dans le but de réduire les risques de
brouil-lage radioélectrique à l'intention des autres
utilisa-teurs, il faut choisir le type d'antenne et son
gain de sorte que la puissance isotrope rayonnée
équivalente (p.i.r.e.) ne dépasse pas l'intensité
nécessaire à l'établissement d'une communication
satisfaisante.
The AMS-00x module can only be operated with the on-
board antenna with which it was approved without ad-
ditional testing.
If an external antenna is used with the AMS-00x mod-
ule, additional testing of the end product is needed to
meet IC requirements as described in the previous sec-
tion.
Further Information
Additional information may be obtained from the In-
dustry Canada website at http://www.ic.gc.ca
The above notice may be affixed to the device instead
of displayed in the user manual.
ADS-MS00x-107R • Preliminary Data Sheet
Page | 16
©2014-2015 ACKme Networks. http://ack.me
September 14, 2015
Regulatory Certification, Section 7
AMS-00x • Embedded Bluetooth Low Energy Solution
evaluation under Article 3.2 of the R&TTE Directive and
does not require further involvement of an R&TTE Di-
rective Notified Body for the final product. [Section
2.2.4]
7.3 Europe
The AMS-00x module is an R&TTE Directive assessed
radio module that is CE marked and has been manufac-
tured and tested with the intention of being integrated
into a final product.
The European Compliance Testing listed in Table 12 was
performed using the AMS-00x on-board antenna.
The AMS-00x module has been tested to R&TTE Di-
rective 1999/5/EC Essential Requirements for Health
and Safety Article 3.1(a), Electromagnetic Compatibility
(EMC) Article 3.1(b), and Radio Article 3.2 and the re-
sults are summarized in Table 12. A Notified Body Opin-
ion has also been issued. All AMS-00x test reports are
available on the ACKme Networks website at
http://ack.me/contact.
Further Information
A document that can be used as a starting point in un-
derstanding the use of Short Range Devices (SRD) in
Europe is the European Radio Communications Com-
mittee (ERC) Recommendation 70-03 E, which can be
downloaded from the European Radio Communications
Office (ERO) at: http://www.ero.dk.
The R&TTE Compliance Association provides guidance
on modular devices in the document titled Technical
Guidance Note 01 available on the website at
Further information may be obtained from the follow-
ing websites:
Radio and Telecommunications Terminal Equip-
ment (R&TTE)
http://ec.europa.eu/enterprise/rtte/index_en.htm
European Conference of Postal and Telecommuni-
cations Administrations (CEPT)
http://www.cept.org
European Telecommunications Standards Institute
(ETSI)
http://www.rtteca.com/html/download_area.htm.
NOTE: To maintain conformance to the testing
listed in Table 12, the module shall be installed in
accordance with the installation instructions in this
data sheet and shall not be modified.
When integrating a radio module into a completed
product the integrator becomes the manufacturer
of the final product and is therefore responsible for
demonstrating compliance of the final product with
the essential requirements of the R&TTE Directive.
http://www.etsi.org
European Radio Communications Office (ERO)
http://www.ero.dk
The Radio and Telecommunications Terminal
Equipment Compliance Association (R&TTE CA)
http://www.rtteca.com/
Labeling and User Information
Requirements
The label on the final product which contains the
AMS-00x module must follow CE marking requirements.
The R&TTE Compliance Association Technical Guidance
Note 01 provides guidance on final product CE marking
External Antenna Requirements
From R&TTE Compliance Association document Tech-
nical Guidance Note 01:
Provided the integrator installing an assessed radio
module with an integral or specific antenna and in-
stalled in conformance with the radio module manufac-
turer’s installation instructions requires no further
ADS-MS00x-107R • Preliminary Data Sheet
Page | 17
©2014-2015 ACKme Networks. http://ack.me
September 14, 2015
Regulatory Certification, Section 7
AMS00x • Embedded Bluetooth Low Energy Solution
Table 12. European Compliance Testing
AMS001
Certification
Standard
Article
Laboratory
Report Number
Date
Safety
EN 60950-1:2006 + A11:2009 +
A1:2010 + A12:2011
3.1(a)
Shenzhen Morlab SZ15010120A01
Communications
2015-Feb-09
Technology Co.,
Ltd.
Health
EMC
EN 50371:2002-03
SZ15010120S01A
2015-Feb-09
2015-Feb-09
EN 301 489-1 v1.9.2 (2011-09)
3.1(b)
SZ15010120E01A
EN301 489-17 v2.2.1 (2012-09)
EN 300 328 v1.8.1 (2012-06)
Radio
3.2
-
SZ15010120W04A
2015-Feb-09
2015-Feb-13
Notified Body
Opinion
PHOENIX TESTLAB 15-110950
0700
AMS002
Certification
Standard
Article
Laboratory
Report Number
Date
Safety
EN 60950-
1:2006+A11:2009+A1:2010
3.1(a)
Shenzhen Morlab SZ14100103A01
Communications
2015-Jan-07
Technology Co.,
Ltd.
Health
EMC
EN 50371:2002-03
SZ14100103S01A
2015-Jan-04
2014-Nov-11
EN 301 489-1 v1.9.2 (2011-09)
3.1(b)
SZ14100103E01
EN301 489-17 v2.2.1 (2012-09)
EN 300 328 v1.8.1 (2012-06)
Radio
3.2
-
SZ14100103W04
2015-Jan-06
2015-Jan-12
Notified Body
Opinion
PHOENIX TESTLAB 15-110130
0700
external antenna is used with the AMS-00x module,
additional testing of the end product is needed to meet
Australian regulatory requirements.
7.4 Australia
Australian radio regulations do not provide a modular
approval policy similar to the United States (FCC) and
Canada (IC). However, AMS-00x module test reports
may be used in part to demonstrate compliance in ac-
cordance with ACMA Radio communications “Short
Range Devices” Standard 2004 which references Aus-
tralia/New Zealand industry standard AS/NZS-
4268:2012. AMS-00x RF transmitter test reports may be
used as part of the product certification and compliance
folder. For further information regarding the availability
of RF test reports, please contact ACKme Networks via
our website at http://ack.me/contact.
Further Information
Additional information may be obtained from the Aus-
tralian Communications and Media Authority website
at http://www.acma.gov.au.
External Antenna Requirements
The compliance test reports provided in Table 12 were
performed using the AMS-00x on-board antenna. If an
ADS-MS00x-107R • Preliminary Data Sheet
Page | 18
©2014-2015 ACKme Networks. http://ack.me
September 14, 2015
Regulatory Certification, Section 7
AMS00x • Embedded Bluetooth Low Energy Solution
7.5 New Zealand
New Zealand radio regulations do not provide a modu-
lar approval policy similar to the United States (FCC)
and Canada (IC). However, AMS-00x module test re-
ports may be used in part to demonstrate compliance
with the New Zealand “General User Radio License for
Short Range Devices”. New Zealand Radio communica-
tions (Radio Standards) Notice 2010 references Austral-
ia/New Zealand industry standard AS/NZS-4268:2012.
AMS-00x RF transmitter test reports may be used as
part of the product certification and compliance folder.
For further information regarding the availability of RF
test reports, please contact ACKme Networks via our
website at http://ack.me/contact.
External Antenna Requirements
The compliance test reports provided in Table 12 were
performed using the AMS-00x on-board antenna. If an
external antenna is used with the AMS-00x module,
additional testing of the end product is needed to meet
New Zealand regulatory requirements.
Further Information
Additional information may be obtained from the New
Zealand Radio Spectrum Ministry of Economic Devel-
opment website at http://www.rsm.govt.nz.
ADS-MS00x-107R • Preliminary Data Sheet
Page | 19
©2014-2015 ACKme Networks. http://ack.me
September 14, 2015
Packaging, Handling & Storage, RoHS, Section 8
AMS00x • Embedded Bluetooth Low Energy Solution
8 Packaging, Handling & Storage, RoHS
8.1 Packaging
AMS00x modules are shipped in an ESD bag.
AMS00x modules are also available in reels each containing 1000 modules. Reels are shipped in an ESD and moisture
resistant sealed bag. The shelf life of the sealed bag is 12 months at 40°C and <90% Relative Humidity (RH). Please
refer to the bag seal date.
8.2 Tape and Reel Specifications
Figure 7 - Tape Specifications
Symbol
A0
B0
D0
E
F
K0
Specification (mm)
11.8 ± 0.10
18.1 ± 0.10
1.5 ± 0.10
1.75 ± 0.10
14.2 ± 0.10
2.70 ± 0.10
Symbol
P
P0
P2
2.00 ± 0.10
T
W
Specification (mm)
20.0 ± 0.10
4.00 ± 0.10
0.30 ± 0.05
32.0 ± 0.30
Tape material : black PS material, in line with ROHS environmental management substances
Tape thickness: 0.3 mm ± 0.05 mm
Tape width: 32mm (1.3")
Protection zone: black PS material
Distance between chain hole centers within the range of ± 0.2 mm of cumulative error
Anti-camber at 1 mm / 250 mm
All dimensions in line with the requirements of EIA-481-D
ADS-MS00x-107R • Preliminary Data Sheet
©2014-2015 ACKme Networks. http://ack.me
Page | 20
September 14, 2015
Packaging, Handling & Storage, RoHS, Section 8
AMS00x • Embedded Bluetooth Low Energy Solution
Figure 8 - Reel Specifications
Symbol
A
B
C1
D
E
H
T
Specification (mm) 2.5 ± 0.2
11 ± 0.2
330 ± 1
99.5 ± 0.1 13.2 ± 0.2 32.8 + 0.3 / -0.2 2.25 ± 0.2
ADS-MS00x-107R • Preliminary Data Sheet
©2014-2015 ACKme Networks. http://ack.me
Page | 21
September 14, 2015
Packaging, Handling & Storage, RoHS, Section 8
AMS00x • Embedded Bluetooth Low Energy Solution
8.3 Handling & Storage
CAUTION
MSL3 Sensitive Device!
AMS00x modules are moisture sensitive devices rated
at Moisture Sensitive Level 3 (MSL3) per IPC/JEDEC
J-STD-20.
After opening the moisture sealed storage bag, mod-
ules that will be subjected to reflow solder or other
high temperature processes must be:
1. mounted to a circuit board within 168 hours at
factory conditions (≤30°C and <60% RH)
OR
2. continuously stored per IPC/JEDEC J-STD-033
Modules that have been exposed to moisture and envi-
ronmental conditions exceeding packaging and storage
conditions MUST be baked before mounting according
to IPC/JEDEC J-STD-033.
Failure to meet packaging and storage conditions will
result in irreparable damage to modules during solder
reflow.
8.4 RoHS Directive
Each AMS00x module is produced
according to the RoHS (Restriction
of the use of certain Hazardous
Substances in electrical and electronic equipment) di-
rective and complies with the directive.
ADS-MS00x-107R • Preliminary Data Sheet
Page | 22
©2014-2015 ACKme Networks. http://ack.me
September 14, 2015
Ordering Information, Section 9
AMS00x • Embedded Bluetooth Low Energy Solution
9 Ordering Information
AMS00x modules are available individually or in a reel of 1000 units as described in the tables below.
Table 13. AMS001 Ordering Information
Part Number
Description
AMS001/S
1 x AMS001 module with TruConnect pre-installed. Each module is individually packaged in an
ESD bag.
AMS001/R
A single reel containing 1000 x AMS001 modules, each with TruConnect pre-installed.
The entire reel is packaged in an ESD and MSL3-rated moisture sensitive bag.
Table 14. AMS002 Ordering Information
Part Number
Description
AMS002/S
1 x AMS002 module with TruConnect pre-installed. Each module is individually packaged in an
ESD bag.
AMS002/R
A single reel containing 1000 x AMS002 modules, each with TruConnect pre-installed.
The entire reel is packaged in an ESD and MSL3-rated moisture sensitive bag.
ADS-MS00x-107R • Preliminary Data Sheet
Page | 23
©2014-2015 ACKme Networks. http://ack.me
September 14, 2015
Revision History & Glossary, Section 10
AMS00x • Embedded Bluetooth Low Energy Solution
10 Revision History & Glossary
10.1 Revision History
Table 15: Document Revision History
Revision
Date
Change Description
ADS-MS00x-100R
ADS-MS00x-101R
10-Nov-2014 Initial version
7-Jan-2015 Note minimum boot voltage
Add packaging section
ADS-MS00x-102R
ADS-MS00x-103R
ADS-MS00x-104R
2-Feb-2015 Note pull-up requirement and minimum deep sleep current
2-Feb-2015 Finalized AMS002 CE regulatory information for AMS002
8-Apr-2015 Added limits for IO pins
Finalized AMS001 regulatory information
ADS-MW00x-105R
ADS-MW00x-106R
9-Jun-2015 Updated GPIO and pin definitions in Pin and Signal Descriptions
28-Aug-2015 Added maximum voltage details for Input and Output Pins
Added vias diagram to Routing Recommendations
Added tape and reel documentation. Removed tray packaging details.
ADS-MW00x-107R
14-Sep-2015 Added Adaptive Frequency Hopping to features and description.
10.2 Glossary
In most cases, acronyms and abbreviations are defined on first use. A comprehensive list of acronyms and other
terms used in ACKme Networks documents are provided on the ACKme Networks website at
http://ack.me/FAQs/Glossary.
ADS-MS00x-107R • Preliminary Data Sheet
©2014-2015 ACKme Networks. http://ack.me
Page | 24
September 14, 2015
AMS00x • Embedded Bluetooth Low Energy Solution
ACKme reserves the right to make changes without further notice to any products or data herein to improve reliability, function, or design.
Information furnished by ACKme is believed to be accurate and reliable. However, ACKme does not assume any liability arising out of the
application or use of this information, nor the application or use of any product described herein, neither does it convey any license under
its patent rights nor the rights of others.
ACKme Networks
Contact Information
+1 (408) 402 8160
http://ack.me/contact
20 North Santa Cruz Ave
Los Gatos CA 95030
United States
© 2014-2015 ACKme Networks Inc. All rights reserved.
ADS-MS00x-107R • Preliminary Data Sheet
September 14, 2015
相关型号:
©2020 ICPDF网 联系我们和版权申明