EFM32WG380F256-QFP100T [SILICON]
Microcontroller, 32-Bit, FLASH, CORTEX-M4F CPU, 48MHz, CMOS, PQFP100;型号: | EFM32WG380F256-QFP100T |
厂家: | SILICON |
描述: | Microcontroller, 32-Bit, FLASH, CORTEX-M4F CPU, 48MHz, CMOS, PQFP100 微控制器 |
文件: | 总82页 (文件大小:2117K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
EFM32WG380 DATASHEET
F256/F128/F64
• ARM Cortex-M4 CPU platform
• External Bus Interface for up to 4x256 MB of external
memory mapped space
• TFT Controller with Direct Drive
• High Performance 32-bit processor @ up to 48 MHz
• DSP instruction support and floating-point unit
• Memory Protection Unit
• Communication interfaces
• 3× Universal Synchronous/Asynchronous Receiv-
er/Transmitter
• Flexible Energy Management System
• 20 nA @ 3 V Shutoff Mode
• UART/SPI/SmartCard (ISO 7816)/IrDA/I2S
• 2× Universal Asynchronous Receiver/Transmitter
• 2× Low Energy UART
• 0.4 µA @ 3 V Shutoff Mode with RTC
• 0.65 µA @ 3 V Stop Mode, including Power-on Reset, Brown-out
Detector, RAM and CPU retention
• Autonomous operation with DMA in Deep Sleep
Mode
• 0.95 µA @ 3 V Deep Sleep Mode, including RTC with 32.768 kHz
oscillator, Power-on Reset, Brown-out Detector, RAM and CPU
retention
• 63 µA/MHz @ 3 V Sleep Mode
• 225 µA/MHz @ 3 V Run Mode, with code executed from flash
• 256/128/64 KB Flash
• 2× I2C Interface with SMBus support
• Address recognition in Stop Mode
• Universal Serial Bus (USB) with Host & OTG support
• Fully USB 2.0 compliant
• 32 KB RAM
• 81 General Purpose I/O pins
• On-chip PHY and embedded 5V to 3.3V regulator
• Ultra low power precision analog peripherals
• 12-bit 1 Msamples/s Analog to Digital Converter
• 8 single ended channels/4 differential channels
• On-chip temperature sensor
• 12-bit 500 ksamples/s Digital to Analog Converter
• 2× Analog Comparator
• Capacitive sensing with up to 16 inputs
• 3× Operational Amplifier
• 6.1 MHz GBW, Rail-to-rail, Programmable Gain
• Supply Voltage Comparator
• Low Energy Sensor Interface (LESENSE)
• Autonomous sensor monitoring in Deep Sleep Mode
• Wide range of sensors supported, including LC sen-
sors and capacitive buttons
• Configurable push-pull, open-drain, pull-up/down, input filter, drive
strength
• Configurable peripheral I/O locations
• 16 asynchronous external interrupts
• Output state retention and wake-up from Shutoff Mode
• 12 Channel DMA Controller
• 12 Channel Peripheral Reflex System (PRS) for autonomous in-
ter-peripheral signaling
• Hardware AES with 128/256-bit keys in 54/75 cycles
• Timers/Counters
• 4× 16-bit Timer/Counter
• 4×3 Compare/Capture/PWM channels
• Dead-Time Insertion on TIMER0
• 16-bit Low Energy Timer
• 1× 24-bit Real-Time Counter and 1× 32-bit Real-Time Counter
• 3× 16/8-bit Pulse Counter
• Ultra efficient Power-on Reset and Brown-Out Detec-
tor
• Debug Interface
• Watchdog Timer with dedicated RC oscillator @ 50 nA
• Backup Power Domain
• 2-pin Serial Wire Debug interface
• 1-pin Serial Wire Viewer
• RTC and retention registers in a separate power domain, avail-
able in all energy modes
• Operation from backup battery when main power drains out
• Embedded Trace Module v3.5 (ETM)
• Pre-Programmed USB/UART Bootloader
• Temperature range -40 to 85 ºC
• Single power supply 1.98 to 3.8 V
• LQFP100 package
32-bit ARM Cortex-M0+, Cortex-M3 and Cortex-M4 microcontrollers for:
• Energy, gas, water and smart metering
• Health and fitness applications
• Smart accessories
• Alarm and security systems
• Industrial and home automation
...the world's most energy friendly microcontrollers
1 Ordering Information
Table 1.1 (p. 2) shows the available EFM32WG380 devices.
Table 1.1. Ordering Information
Ordering Code
Flash (kB) RAM (kB)
Max
Speed
(MHz)
Supply
Voltage
(V)
Temperature
(ºC)
Package
EFM32WG380F64-QFP100
EFM32WG380F128-QFP100
EFM32WG380F256-QFP100
64
32
32
32
48
48
48
1.98 - 3.8
1.98 - 3.8
1.98 - 3.8
-40 - 85
-40 - 85
-40 - 85
LQFP100
LQFP100
LQFP100
128
256
Visit www.silabs.com for information on global distributors and representatives.
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
2
...the world's most energy friendly microcontrollers
2 System Summary
2.1 System Introduction
The EFM32 MCUs are the world’s most energy friendly microcontrollers. With a unique combination of
the powerful 32-bit ARM Cortex-M4, with DSP instruction support and floating-point unit, innovative low
energy techniques, short wake-up time from energy saving modes, and a wide selection of peripherals,
the EFM32WG microcontroller is well suited for any battery operated application as well as other systems
requiring high performance and low-energy consumption. This section gives a short introduction to each
of the modules in general terms and also shows a summary of the configuration for the EFM32WG380
devices. For a complete feature set and in-depth information on the modules, the reader is referred to
the EFM32WG Reference Manual.
A block diagram of the EFM32WG380 is shown in Figure 2.1 (p. 3) .
Figure 2.1. Block Diagram
WG380F64/ 128/ 256
Core and Memory
Clock Management
Energy Management
Aux High Freq.
RC
Oscillator
High Freq.
RC
Oscillator
Voltage
Comparator
Voltage
Regulator
Memory
Protection
Unit
ARM Cortex™M4 processor
with DSP extensions and FPU
Low Freq.
RC
Oscillator
High Freq.
Crystal
Oscillator
Brown- out
Detector
Power- on
Reset
Flash
Debug
Interface
w/ ETM
DMA
Controller
RAM
Back- up
Power
Domain
Program
Memory
Memory
Low Freq.
Crystal
Oscillator
Ultra Low Freq.
RC
Oscillator
32- bit bus
Peripheral Reflex System
Serial Interfaces
I/ O Ports
Timers and Triggers
Analog Interfaces
Security
Timer/
Counter
Ext. Bus
Interface
TFT
Driver
Hardware
AES
LESENSE
USART
UART
ADC
Low Energy
Timer
Real Time
Counter
Low
Energy
Uart™
General
Purpose
I/ O
External
Interrupts
Operational
Amplifier
I2C
DAC
Pulse
Counter
Watchdog
Timer
Pin
Reset
Pin
Wakeup
Analog
Comparator
Back- up
RTC
USB
2.1.1 ARM Cortex-M4 Core
The ARM Cortex-M4 includes a 32-bit RISC processor, with DSP instruction support and floating-point
unit, which can achieve as much as 1.25 Dhrystone MIPS/MHz. A Memory Protection Unit with support
for up to 8 memory segments is included, as well as a Wake-up Interrupt Controller handling interrupts
triggered while the CPU is asleep. The EFM32 implementation of the Cortex-M4 is described in detail
in ARM Cortex-M4 Devices Generic User Guide.
2.1.2 Debug Interface (DBG)
This device includes hardware debug support through a 2-pin serial-wire debug interface and an Embed-
ded Trace Module (ETM) for data/instruction tracing. In addition there is also a 1-wire Serial Wire Viewer
pin which can be used to output profiling information, data trace and software-generated messages.
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
3
...the world's most energy friendly microcontrollers
2.1.3 Memory System Controller (MSC)
The Memory System Controller (MSC) is the program memory unit of the EFM32WG microcontroller.
The flash memory is readable and writable from both the Cortex-M4 and DMA. The flash memory is
divided into two blocks; the main block and the information block. Program code is normally written to
the main block. Additionally, the information block is available for special user data and flash lock bits.
There is also a read-only page in the information block containing system and device calibration data.
Read and write operations are supported in the energy modes EM0 and EM1.
2.1.4 Direct Memory Access Controller (DMA)
The Direct Memory Access (DMA) controller performs memory operations independently of the CPU.
This has the benefit of reducing the energy consumption and the workload of the CPU, and enables
the system to stay in low energy modes when moving for instance data from the USART to RAM or
from the External Bus Interface to a PWM-generating timer. The DMA controller uses the PL230 µDMA
controller licensed from ARM.
2.1.5 Reset Management Unit (RMU)
The RMU is responsible for handling the reset functionality of the EFM32WG.
2.1.6 Energy Management Unit (EMU)
The Energy Management Unit (EMU) manage all the low energy modes (EM) in EFM32WG microcon-
trollers. Each energy mode manages if the CPU and the various peripherals are available. The EMU
can also be used to turn off the power to unused SRAM blocks.
2.1.7 Clock Management Unit (CMU)
The Clock Management Unit (CMU) is responsible for controlling the oscillators and clocks on-board the
EFM32WG. The CMU provides the capability to turn on and off the clock on an individual basis to all
peripheral modules in addition to enable/disable and configure the available oscillators. The high degree
of flexibility enables software to minimize energy consumption in any specific application by not wasting
power on peripherals and oscillators that are inactive.
2.1.8 Watchdog (WDOG)
The purpose of the watchdog timer is to generate a reset in case of a system failure, to increase appli-
cation reliability. The failure may e.g. be caused by an external event, such as an ESD pulse, or by a
software failure.
2.1.9 Peripheral Reflex System (PRS)
The Peripheral Reflex System (PRS) system is a network which lets the different peripheral module
communicate directly with each other without involving the CPU. Peripheral modules which send out
Reflex signals are called producers. The PRS routes these reflex signals to consumer peripherals which
apply actions depending on the data received. The format for the Reflex signals is not given, but edge
triggers and other functionality can be applied by the PRS.
2.1.10 External Bus Interface (EBI)
The External Bus Interface provides access to external parallel interface devices such as SRAM, FLASH,
ADCs and LCDs. The interface is memory mapped into the address bus of the Cortex-M4. This enables
seamless access from software without manually manipulating the IO settings each time a read or write
is performed. The data and address lines are multiplexed in order to reduce the number of pins required
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
4
...the world's most energy friendly microcontrollers
to interface the external devices. The timing is adjustable to meet specifications of the external devices.
The interface is limited to asynchronous devices.
2.1.11 TFT Direct Drive
The EBI contains a TFT controller which can drive a TFT via a 565 RGB interface. The TFT controller
supports programmable display and port sizes and offers accurate control of frequency and setup and
hold timing. Direct Drive is supported for TFT displays which do not have their own frame buffer. In
that case TFT Direct Drive can transfer data from either on-chip memory or from an external memory
device to the TFT at low CPU load. Automatic alpha-blending and masking is also supported for transfers
through the EBI interface.
2.1.12 Universal Serial Bus Controller (USB)
The USB is a full-speed USB 2.0 compliant OTG host/device controller. The USB can be used in Device,
On-the-go (OTG) Dual Role Device or Host-only configuration. In OTG mode the USB supports both
Host Negotiation Protocol (HNP) and Session Request Protocol (SRP). The device supports both full-
speed (12MBit/s) and low speed (1.5MBit/s) operation. The USB device includes an internal dedicated
Descriptor-Based Scatter/Garther DMA and supports up to 6 OUT endpoints and 6 IN endpoints, in
addition to endpoint 0. The on-chip PHY includes all OTG features, except for the voltage booster for
supplying 5V to VBUS when operating as host.
2.1.13 Inter-Integrated Circuit Interface (I2C)
The I2C module provides an interface between the MCU and a serial I2C-bus. It is capable of acting as
both a master and a slave, and supports multi-master buses. Both standard-mode, fast-mode and fast-
mode plus speeds are supported, allowing transmission rates all the way from 10 kbit/s up to 1 Mbit/s.
Slave arbitration and timeouts are also provided to allow implementation of an SMBus compliant system.
The interface provided to software by the I2C module, allows both fine-grained control of the transmission
process and close to automatic transfers. Automatic recognition of slave addresses is provided in all
energy modes.
2.1.14 Universal Synchronous/Asynchronous Receiver/Transmitter (US-
ART)
The Universal Synchronous Asynchronous serial Receiver and Transmitter (USART) is a very flexible
serial I/O module. It supports full duplex asynchronous UART communication as well as RS-485, SPI,
MicroWire and 3-wire. It can also interface with ISO7816 SmartCards, IrDA and I2S devices.
2.1.15 Pre-Programmed USB/UART Bootloader
The bootloader presented in application note AN0042 is pre-programmed in the device at factory. The
bootloader enables users to program the EFM32 through a UART or a USB CDC class virtual UART
without the need for a debugger. The autobaud feature, interface and commands are described further
in the application note.
2.1.16 Universal Asynchronous Receiver/Transmitter (UART)
The Universal Asynchronous serial Receiver and Transmitter (UART) is a very flexible serial I/O module.
It supports full- and half-duplex asynchronous UART communication.
2.1.17 Low Energy Universal Asynchronous Receiver/Transmitter
(LEUART)
The unique LEUARTTM, the Low Energy UART, is a UART that allows two-way UART communication on
a strict power budget. Only a 32.768 kHz clock is needed to allow UART communication up to 9600 baud/
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
5
...the world's most energy friendly microcontrollers
s. The LEUART includes all necessary hardware support to make asynchronous serial communication
possible with minimum of software intervention and energy consumption.
2.1.18 Timer/Counter (TIMER)
The 16-bit general purpose Timer has 3 compare/capture channels for input capture and compare/Pulse-
Width Modulation (PWM) output. TIMER0 also includes a Dead-Time Insertion module suitable for motor
control applications.
2.1.19 Real Time Counter (RTC)
The Real Time Counter (RTC) contains a 24-bit counter and is clocked either by a 32.768 kHz crystal
oscillator, or a 32.768 kHz RC oscillator. In addition to energy modes EM0 and EM1, the RTC is also
available in EM2. This makes it ideal for keeping track of time since the RTC is enabled in EM2 where
most of the device is powered down.
2.1.20 Backup Real Time Counter (BURTC)
The Backup Real Time Counter (BURTC) contains a 32-bit counter and is clocked either by a 32.768 kHz
crystal oscillator, a 32.768 kHz RC oscillator or a 1 kHz ULFRCO. The BURTC is available in all Energy
Modes and it can also run in backup mode, making it operational even if the main power should drain out.
2.1.21 Low Energy Timer (LETIMER)
The unique LETIMERTM, the Low Energy Timer, is a 16-bit timer that is available in energy mode EM2
in addition to EM1 and EM0. Because of this, it can be used for timing and output generation when most
of the device is powered down, allowing simple tasks to be performed while the power consumption of
the system is kept at an absolute minimum. The LETIMER can be used to output a variety of waveforms
with minimal software intervention. It is also connected to the Real Time Counter (RTC), and can be
configured to start counting on compare matches from the RTC.
2.1.22 Pulse Counter (PCNT)
The Pulse Counter (PCNT) can be used for counting pulses on a single input or to decode quadrature
encoded inputs. It runs off either the internal LFACLK or the PCNTn_S0IN pin as external clock source.
The module may operate in energy mode EM0 – EM3.
2.1.23 Analog Comparator (ACMP)
The Analog Comparator is used to compare the voltage of two analog inputs, with a digital output indi-
cating which input voltage is higher. Inputs can either be one of the selectable internal references or from
external pins. Response time and thereby also the current consumption can be configured by altering
the current supply to the comparator.
2.1.24 Voltage Comparator (VCMP)
The Voltage Supply Comparator is used to monitor the supply voltage from software. An interrupt can
be generated when the supply falls below or rises above a programmable threshold. Response time and
thereby also the current consumption can be configured by altering the current supply to the comparator.
2.1.25 Analog to Digital Converter (ADC)
The ADC is a Successive Approximation Register (SAR) architecture, with a resolution of up to 12 bits
at up to one million samples per second. The integrated input mux can select inputs from 8 external
pins and 6 internal signals.
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
6
...the world's most energy friendly microcontrollers
2.1.26 Digital to Analog Converter (DAC)
The Digital to Analog Converter (DAC) can convert a digital value to an analog output voltage. The DAC
is fully differential rail-to-rail, with 12-bit resolution. It has two single ended output buffers which can be
combined into one differential output. The DAC may be used for a number of different applications such
as sensor interfaces or sound output.
2.1.27 Operational Amplifier (OPAMP)
The EFM32WG380 features 3 Operational Amplifiers. The Operational Amplifier is a versatile general
purpose amplifier with rail-to-rail differential input and rail-to-rail single ended output. The input can be set
to pin, DAC or OPAMP, whereas the output can be pin, OPAMP or ADC. The current is programmable
and the OPAMP has various internal configurations such as unity gain, programmable gain using internal
resistors etc.
2.1.28 Low Energy Sensor Interface (LESENSE)
The Low Energy Sensor Interface (LESENSETM), is a highly configurable sensor interface with support
for up to 16 individually configurable sensors. By controlling the analog comparators and DAC, LESENSE
is capable of supporting a wide range of sensors and measurement schemes, and can for instance mea-
sure LC sensors, resistive sensors and capacitive sensors. LESENSE also includes a programmable
FSM which enables simple processing of measurement results without CPU intervention. LESENSE is
available in energy mode EM2, in addition to EM0 and EM1, making it ideal for sensor monitoring in
applications with a strict energy budget.
2.1.29 Backup Power Domain
The backup power domain is a separate power domain containing a Backup Real Time Counter, BURTC,
and a set of retention registers, available in all energy modes. This power domain can be configured to
automatically change power source to a backup battery when the main power drains out. The backup
power domain enables the EFM32WG380 to keep track of time and retain data, even if the main power
source should drain out.
2.1.30 Advanced Encryption Standard Accelerator (AES)
The AES accelerator performs AES encryption and decryption with 128-bit or 256-bit keys. Encrypting or
decrypting one 128-bit data block takes 52 HFCORECLK cycles with 128-bit keys and 75 HFCORECLK
cycles with 256-bit keys. The AES module is an AHB slave which enables efficient access to the data
and key registers. All write accesses to the AES module must be 32-bit operations, i.e. 8- or 16-bit
operations are not supported.
2.1.31 General Purpose Input/Output (GPIO)
In the EFM32WG380, there are 81 General Purpose Input/Output (GPIO) pins, which are divided into
ports with up to 16 pins each. These pins can individually be configured as either an output or input. More
advanced configurations like open-drain, filtering and drive strength can also be configured individually
for the pins. The GPIO pins can also be overridden by peripheral pin connections, like Timer PWM
outputs or USART communication, which can be routed to several locations on the device. The GPIO
supports up to 16 asynchronous external pin interrupts, which enables interrupts from any pin on the
device. Also, the input value of a pin can be routed through the Peripheral Reflex System to other
peripherals.
2.2 Configuration Summary
The features of the EFM32WG380 is a subset of the feature set described in the EFM32WG Reference
Manual. Table 2.1 (p. 8) describes device specific implementation of the features.
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
7
...the world's most energy friendly microcontrollers
Table 2.1. Configuration Summary
Module
Cortex-M4
DBG
Configuration
Full configuration
Pin Connections
NA
Full configuration
DBG_SWCLK, DBG_SWDIO,
DBG_SWO
MSC
DMA
RMU
EMU
CMU
WDOG
PRS
Full configuration
Full configuration
Full configuration
Full configuration
Full configuration
Full configuration
Full configuration
Full configuration
NA
NA
NA
NA
CMU_OUT0, CMU_OUT1
NA
NA
USB
USB_VBUS, USB_VBUSEN,
USB_VREGI, USB_VREGO, USB_DM,
USB_DMPU, USB_DP, USB_ID
EBI
Full configuration
EBI_A[27:0], EBI_AD[15:0], EBI_ARDY,
EBI_ALE, EBI_BL[1:0], EBI_CS[3:0],
EBI_CSTFT, EBI_DCLK, EBI_DTEN,
EBI_HSNC, EBI_NANDREn,
EBI_NANDWEn, EBI_REn, EBI_VSNC,
EBI_WEn
I2C0
Full configuration
I2C0_SDA, I2C0_SCL
I2C1_SDA, I2C1_SCL
US0_TX, US0_RX. US0_CLK, US0_CS
US1_TX, US1_RX, US1_CLK, US1_CS
US2_TX, US2_RX, US2_CLK, US2_CS
U0_TX, U0_RX
I2C1
Full configuration
USART0
USART1
USART2
UART0
UART1
LEUART0
LEUART1
TIMER0
TIMER1
TIMER2
TIMER3
RTC
Full configuration with IrDA
Full configuration with I2S
Full configuration with I2S
Full configuration
Full configuration
U1_TX, U1_RX
Full configuration
LEU0_TX, LEU0_RX
LEU1_TX, LEU1_RX
TIM0_CC[2:0], TIM0_CDTI[2:0]
TIM1_CC[2:0]
Full configuration
Full configuration with DTI
Full configuration
Full configuration
TIM2_CC[2:0]
Full configuration
TIM3_CC[2:0]
Full configuration
NA
BURTC
LETIMER0
PCNT0
PCNT1
PCNT2
ACMP0
ACMP1
Full configuration
NA
Full configuration
LET0_O[1:0]
Full configuration, 16-bit count register PCNT0_S[1:0]
Full configuration, 8-bit count register
Full configuration, 8-bit count register
Full configuration
PCNT1_S[1:0]
PCNT2_S[1:0]
ACMP0_CH[7:0], ACMP0_O
ACMP1_CH[7:0], ACMP1_O
Full configuration
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
8
...the world's most energy friendly microcontrollers
Module
VCMP
ADC0
Configuration
Pin Connections
Full configuration
Full configuration
Full configuration
Full configuration
NA
ADC0_CH[7:0]
DAC0
DAC0_OUT[1:0], DAC0_OUTxALT
OPAMP
Outputs: OPAMP_OUTx,
OPAMP_OUTxALT, Inputs:
OPAMP_Px, OPAMP_Nx
AES
Full configuration
81 pins
NA
GPIO
Available pins are shown in
Table 4.3 (p. 67)
2.3 Memory Map
The EFM32WG380 memory map is shown in Figure 2.2 (p. 9), with RAM and Flash sizes for the
largest memory configuration.
Figure 2.2. EFM32WG380 Memory Map with largest RAM and Flash sizes
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
9
...the world's most energy friendly microcontrollers
3 Electrical Characteristics
3.1 Test Conditions
3.1.1 Typical Values
The typical data are based on TAMB=25°C and VDD=3.0 V, as defined in Table 3.2 (p. 10), by simu-
lation and/or technology characterisation unless otherwise specified.
3.1.2 Minimum and Maximum Values
The minimum and maximum values represent the worst conditions of ambient temperature, supply volt-
age and frequencies, as defined in Table 3.2 (p. 10), by simulation and/or technology characterisa-
tion unless otherwise specified.
3.2 Absolute Maximum Ratings
The absolute maximum ratings are stress ratings, and functional operation under such conditions are
not guaranteed. Stress beyond the limits specified in Table 3.1 (p. 10) may affect the device reliability
or cause permanent damage to the device. Functional operating conditions are given in Table 3.2 (p.
10) .
Table 3.1. Absolute Maximum Ratings
Symbol
Parameter
Condition
Min
Typ
Max
Unit
1501 °C
TSTG
Storage tempera-
ture range
-40
TS
Maximum soldering Latest IPC/JEDEC J-STD-020
260 °C
temperature
Standard
VDDMAX
External main sup-
ply voltage
0
3.8
V
V
VIOPIN
Voltage on any I/O
pin
-0.3
VDD+0.3
1Based on programmed devices tested for 10000 hours at 150ºC. Storage temperature affects retention of preprogrammed cal-
ibration values stored in flash. Please refer to the Flash section in the Electrical Characteristics for information on flash data re-
tention for different temperatures.
3.3 General Operating Conditions
3.3.1 General Operating Conditions
Table 3.2. General Operating Conditions
Symbol
TAMB
VDDOP
fAPB
Parameter
Min
Typ
Max
Unit
85 °C
3.8
Ambient temperature range
Operating supply voltage
Internal APB clock frequency
Internal AHB clock frequency
-40
1.98
V
48 MHz
48 MHz
fAHB
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
10
...the world's most energy friendly microcontrollers
3.3.2 Environmental
Table 3.3. Environmental
Symbol
Parameter
Condition
Min
Typ
Max
Unit
VESDHBM
ESD (Human Body
Model HBM)
TAMB=25°C
2000
750
V
VESDCDM
ESD (Charged De-
vice Model, CDM)
TAMB=25°C
V
Latch-up sensitivity passed: ±100 mA/1.5 × VSUPPLY(max) according to JEDEC JESD 78 method Class
II, 85°C.
3.4 Current Consumption
Table 3.4. Current Consumption
Symbol
Parameter
Condition
Min
Typ
Max
Unit
48 MHz HFXO, all peripheral
clocks disabled, VDD= 3.0 V,
TAMB=25°C
225
225
226
227
228
229
230
231
232
233
238
238
236 µA/
MHz
48 MHz HFXO, all peripheral
clocks disabled, VDD= 3.0 V,
TAMB=85°C
µA/
MHz
28 MHz HFRCO, all peripher-
al clocks disabled, VDD= 3.0 V,
TAMB=25°C
238 µA/
MHz
28 MHz HFRCO, all peripher-
al clocks disabled, VDD= 3.0 V,
TAMB=85°C
µA/
MHz
21 MHz HFRCO, all peripher-
al clocks disabled, VDD= 3.0 V,
TAMB=25°C
240 µA/
MHz
21 MHz HFRCO, all peripher-
al clocks disabled, VDD= 3.0 V,
TAMB=85°C
µA/
MHz
EM0 current. No
prescaling. Running
prime number cal-
culation code from
Flash. (Production
test condition = 14
MHz)
IEM0
14 MHz HFRCO, all peripher-
al clocks disabled, VDD= 3.0 V,
TAMB=25°C
243 µA/
MHz
14 MHz HFRCO, all peripher-
al clocks disabled, VDD= 3.0 V,
TAMB=85°C
µA/
MHz
11 MHz HFRCO, all peripher-
al clocks disabled, VDD= 3.0 V,
TAMB=25°C
245 µA/
MHz
11 MHz HFRCO, all peripher-
al clocks disabled, VDD= 3.0 V,
TAMB=85°C
µA/
MHz
6.6 MHz HFRCO, all peripher-
al clocks disabled, VDD= 3.0 V,
TAMB=25°C
250 µA/
MHz
6.6 MHz HFRCO, all peripher-
al clocks disabled, VDD= 3.0 V,
TAMB=85°C
µA/
MHz
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
11
...the world's most energy friendly microcontrollers
Symbol
Parameter
Condition
Min
Typ
Max
Unit
1.2 MHz HFRCO, all peripher-
al clocks disabled, VDD= 3.0 V,
TAMB=25°C
271
275
63
286 µA/
MHz
1.2 MHz HFRCO, all peripher-
al clocks disabled, VDD= 3.0 V,
TAMB=85°C
µA/
MHz
48 MHz HFXO, all peripheral
clocks disabled, VDD= 3.0 V,
TAMB=25°C
75 µA/
MHz
48 MHz HFXO, all peripheral
clocks disabled, VDD= 3.0 V,
TAMB=85°C
65
76 µA/
MHz
28 MHz HFRCO, all peripher-
al clocks disabled, VDD= 3.0 V,
TAMB=25°C
64
75 µA/
MHz
28 MHz HFRCO, all peripher-
al clocks disabled, VDD= 3.0 V,
TAMB=85°C
65
77 µA/
MHz
21 MHz HFRCO, all peripher-
al clocks disabled, VDD= 3.0 V,
TAMB=25°C
65
76 µA/
MHz
21 MHz HFRCO, all peripher-
al clocks disabled, VDD= 3.0 V,
TAMB=85°C
66
78 µA/
MHz
14 MHz HFRCO, all peripher-
al clocks disabled, VDD= 3.0 V,
TAMB=25°C
67
79 µA/
MHz
EM1 current (Pro-
duction test condi-
tion = 14 MHz)
IEM1
14 MHz HFRCO, all peripher-
al clocks disabled, VDD= 3.0 V,
TAMB=85°C
68
82 µA/
MHz
11 MHz HFRCO, all peripher-
al clocks disabled, VDD= 3.0 V,
TAMB=25°C
68
81 µA/
MHz
11 MHz HFRCO, all peripher-
al clocks disabled, VDD= 3.0 V,
TAMB=85°C
70
83 µA/
MHz
6.6 MHz HFRCO, all peripher-
al clocks disabled, VDD= 3.0 V,
TAMB=25°C
74
87 µA/
MHz
6.6 MHz HFRCO, all peripher-
al clocks disabled, VDD= 3.0 V,
TAMB=85°C
76
89 µA/
MHz
1.2 MHz HFRCO. all peripher-
al clocks disabled, VDD= 3.0 V,
TAMB=25°C
106
112
0.951
120 µA/
MHz
1.2 MHz HFRCO. all peripher-
al clocks disabled, VDD= 3.0 V,
TAMB=85°C
129 µA/
MHz
EM2 current with RTC
prescaled to 1 Hz, 32.768
kHz LFRCO, VDD= 3.0 V,
TAMB=25°C
1.71 µA
IEM2
EM2 current
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
12
...the world's most energy friendly microcontrollers
Symbol
Parameter
Condition
Min
Typ
Max
Unit
4.01 µA
EM2 current with RTC
prescaled to 1 Hz, 32.768
kHz LFRCO, VDD= 3.0 V,
TAMB=85°C
3.01
VDD= 3.0 V, TAMB=25°C
VDD= 3.0 V, TAMB=85°C
VDD= 3.0 V, TAMB=25°C
VDD= 3.0 V, TAMB=85°C
0.65
2.65
0.02
0.44
1.3 µA
4.0 µA
IEM3
EM3 current
EM4 current
0.055 µA
0.9 µA
IEM4
1Using backup RTC.
3.4.1 EM1 Current Consumption
Figure 3.1. EM1 Current consumption with all peripheral clocks disabled and HFXO running at
48MHz
3.15
3.10
3.05
3.00
2.95
2.90
3.15
3.10
3.05
3.00
2.95
2.90
2.0V
2.2V
2.4V
2.6V
2.8V
3.0V
3.2V
3.4V
3.6V
3.8V
- 40°C
- 15°C
5°C
25°C
45°C
65°C
85°C
2.0
2.2
2.4
2.6
2.8
3.0
3.2
3.4
3.6
3.8
–40
–15
5
25
45
65
85
Vdd [V]
Temperature [°C]
Figure 3.2. EM1 Current consumption with all peripheral clocks disabled and HFRCO running
at 28MHz
1.85
1.80
1.75
1.70
1.65
1.60
1.85
1.80
1.75
1.70
1.65
1.60
2.0V
2.2V
2.4V
2.6V
2.8V
3.0V
3.2V
3.4V
3.6V
3.8V
- 40°C
- 15°C
5°C
25°C
45°C
65°C
85°C
2.0
2.2
2.4
2.6
2.8
3.0
3.2
3.4
3.6
3.8
–40
–15
5
25
45
65
85
Vdd [V]
Temperature [°C]
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
13
...the world's most energy friendly microcontrollers
Figure 3.3. EM1 Current consumption with all peripheral clocks disabled and HFRCO running
at 21MHz
1.42
1.40
1.38
1.36
1.34
1.32
1.30
1.28
1.26
1.24
1.42
1.40
1.38
1.36
1.34
1.32
1.30
1.28
1.26
1.24
2.0V
2.2V
2.4V
2.6V
2.8V
3.0V
3.2V
3.4V
3.6V
3.8V
- 40°C
- 15°C
5°C
25°C
45°C
65°C
85°C
2.0
2.2
2.4
2.6
2.8
3.0
3.2
3.4
3.6
3.8
–40
–15
5
25
45
65
85
Vdd [V]
Temperature [°C]
Figure 3.4. EM1 Current consumption with all peripheral clocks disabled and HFRCO running
at 14MHz
0.98
0.96
0.94
0.92
0.90
0.88
0.86
0.98
0.96
0.94
0.92
0.90
0.88
0.86
2.0V
2.2V
2.4V
2.6V
2.8V
3.0V
3.2V
3.4V
3.6V
3.8V
- 40°C
- 15°C
5°C
25°C
45°C
65°C
85°C
2.0
2.2
2.4
2.6
2.8
3.0
3.2
3.4
3.6
3.8
–40
–15
5
25
45
65
85
Vdd [V]
Temperature [°C]
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
14
...the world's most energy friendly microcontrollers
Figure 3.5. EM1 Current consumption with all peripheral clocks disabled and HFRCO running
at 11MHz
0.78
0.76
0.74
0.72
0.70
0.78
0.76
0.74
0.72
0.70
2.0V
2.2V
2.4V
2.6V
2.8V
3.0V
3.2V
3.4V
3.6V
3.8V
- 40°C
- 15°C
5°C
25°C
45°C
65°C
85°C
2.0
2.2
2.4
2.6
2.8
3.0
3.2
3.4
3.6
3.8
–40
–15
5
25
45
65
85
Vdd [V]
Temperature [°C]
Figure 3.6. EM1 Current consumption with all peripheral clocks disabled and HFRCO running
at 6.6MHz
0.52
0.51
0.50
0.49
0.48
0.47
0.46
0.45
0.52
0.51
0.50
0.49
0.48
0.47
0.46
0.45
2.0V
2.2V
2.4V
2.6V
2.8V
3.0V
3.2V
3.4V
3.6V
3.8V
- 40°C
- 15°C
5°C
25°C
45°C
65°C
85°C
2.0
2.2
2.4
2.6
2.8
3.0
3.2
3.4
3.6
3.8
–40
–15
5
25
45
65
85
Vdd [V]
Temperature [°C]
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
15
...the world's most energy friendly microcontrollers
Figure 3.7. EM1 Current consumption with all peripheral clocks disabled and HFRCO running
at 1.2MHz
0.138
0.136
0.134
0.132
0.130
0.128
0.126
0.124
0.122
0.160
0.155
0.150
0.145
0.140
0.135
0.130
0.125
0.120
0.115
- 40°C
- 15°C
5°C
2.0V
2.2V
2.4V
2.6V
2.8V
3.0V
3.2V
3.4V
3.6V
3.8V
25°C
45°C
65°C
85°C
2.0
2.2
2.4
2.6
2.8
3.0
3.2
3.4
3.6
3.8
–40
–15
5
25
45
65
85
Vdd [V]
Temperature [°C]
3.4.2 EM2 Current Consumption
Figure 3.8. EM2 current consumption. RTC1 prescaled to 1kHz, 32.768 kHz LFRCO.
3.5
3.0
2.5
2.0
1.5
1.0
0.5
3.5
3.0
2.5
2.0
1.5
1.0
0.5
- 40.0°C
- 15.0°C
5.0°C
Vdd= 2.0V
Vdd= 2.2V
Vdd= 2.4V
Vdd= 2.6V
Vdd= 2.8V
Vdd= 3.0V
Vdd= 3.2V
Vdd= 3.4V
Vdd= 3.6V
Vdd= 3.8V
25.0°C
45.0°C
65.0°C
85.0°C
2.0
2.2
2.4
2.6
2.8
3.0
3.2
3.4
3.6
3.8
–40
–20
0
20
40
60
80
Vdd [V]
Temperature [°C]
1Using backup RTC.
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
16
...the world's most energy friendly microcontrollers
3.4.3 EM3 Current Consumption
Figure 3.9. EM3 current consumption.
3.0
3.0
- 40.0°C
Vdd= 2.0V
- 15.0°C
5.0°C
Vdd= 2.2V
Vdd= 2.4V
2.5
2.0
1.5
1.0
0.5
0.0
2.5
25.0°C
45.0°C
65.0°C
85.0°C
Vdd= 2.6V
Vdd= 2.8V
Vdd= 3.0V
2.0
Vdd= 3.2V
Vdd= 3.4V
Vdd= 3.6V
1.5
1.0
0.5
0.0
Vdd= 3.8V
2.0
2.2
2.4
2.6
2.8
3.0
3.2
3.4
3.6
3.8
–40
–20
0
20
40
60
80
Vdd [V]
Temperature [°C]
3.4.4 EM4 Current Consumption
Figure 3.10. EM4 current consumption.
0.7
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
- 40.0°C
Vdd= 2.0V
Vdd= 2.2V
Vdd= 2.4V
Vdd= 2.6V
Vdd= 2.8V
Vdd= 3.0V
Vdd= 3.2V
Vdd= 3.4V
Vdd= 3.6V
Vdd= 3.8V
- 15.0°C
0.6
0.5
0.4
0.3
0.2
0.1
0.0
5.0°C
25.0°C
45.0°C
65.0°C
85.0°C
2.0
2.2
2.4
2.6
2.8
3.0
3.2
3.4
3.6
3.8
–40
–20
0
20
40
60
80
Vdd [V]
Temperature [°C]
3.5 Transition between Energy Modes
The transition times are measured from the trigger to the first clock edge in the CPU.
Table 3.5. Energy Modes Transitions
Symbol
Parameter
Min
Typ
Max
Unit
tEM10
Transition time from EM1 to EM0
0
HF-
CORE-
CLK
cycles
tEM20
tEM30
tEM40
Transition time from EM2 to EM0
Transition time from EM3 to EM0
Transition time from EM4 to EM0
2
2
µs
µs
µs
163
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
17
...the world's most energy friendly microcontrollers
3.6 Power Management
The EFM32WG requires the AVDD_x, VDD_DREG and IOVDD_x pins to be connected together (with
optional filter) at the PCB level. For practical schematic recommendations, please see the application
note, "AN0002 EFM32 Hardware Design Considerations".
Table 3.6. Power Management
Symbol
Parameter
Condition
Min
Typ
Max
Unit
VBODextthr-
BOD threshold on
falling external sup-
ply voltage
1.74
1.96
1.98
1.98
V
VBODextthr+
BOD threshold on
rising external sup-
ply voltage
1.85
V
V
VPORthr+
Power-on Reset
(POR) threshold on
rising external sup-
ply voltage
tRESET
Delay from reset
is released until
program execution
starts
Applies to Power-on Reset,
Brown-out Reset and pin reset.
163
µs
CDECOUPLE
CUSB_VREGO
CUSB_VREGI
Voltage regulator
decoupling capaci-
tor.
X5R capacitor recommended.
Apply between DECOUPLE pin
and GROUND
1
1
µF
µF
µF
USB voltage regu-
lator out decoupling Apply between USB_VREGO
capacitor. pin and GROUND
X5R capacitor recommended.
USB voltage regula- X5R capacitor recommended.
tor in decoupling ca- Apply between USB_VREGI
4.7
pacitor.
pin and GROUND
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
18
...the world's most energy friendly microcontrollers
3.7 Flash
Table 3.7. Flash
Symbol
Parameter
Condition
Min
Typ
Max
Unit
ECFLASH
Flash erase cycles
before failure
20000
cycles
TAMB<150°C
10000
10
h
RETFLASH
Flash data retention TAMB<85°C
TAMB<70°C
years
years
µs
20
tW_PROG
Word (32-bit) pro-
gramming time
20
tPERASE
tDERASE
IERASE
IWRITE
Page erase time
Device erase time
Erase current
20
40
20.4
40.8
20.8 ms
41.6 ms
71 mA
71 mA
Write current
VFLASH
Supply voltage dur-
ing flash erase and
write
1.98
3.8
V
1Measured at 25°C
3.8 General Purpose Input Output
Table 3.8. GPIO
Symbol
VIOIL
Parameter
Condition
Min
Typ
Max
0.30VDD
Unit
V
Input low voltage
Input high voltage
VIOIH
0.70VDD
V
Sourcing 0.1 mA, VDD=1.98 V,
GPIO_Px_CTRL DRIVEMODE
= LOWEST
0.80VDD
0.90VDD
0.85VDD
0.90VDD
V
Sourcing 0.1 mA, VDD=3.0 V,
GPIO_Px_CTRL DRIVEMODE
= LOWEST
V
V
V
V
V
V
Sourcing 1 mA, VDD=1.98 V,
GPIO_Px_CTRL DRIVEMODE
= LOW
Output high volt-
age (Production test
condition = 3.0V,
DRIVEMODE =
STANDARD)
Sourcing 1 mA, VDD=3.0 V,
GPIO_Px_CTRL DRIVEMODE
= LOW
VIOOH
Sourcing 6 mA, VDD=1.98 V,
GPIO_Px_CTRL DRIVEMODE
= STANDARD
0.75VDD
0.85VDD
0.60VDD
Sourcing 6 mA, VDD=3.0 V,
GPIO_Px_CTRL DRIVEMODE
= STANDARD
Sourcing 20 mA, VDD=1.98 V,
GPIO_Px_CTRL DRIVEMODE
= HIGH
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
19
...the world's most energy friendly microcontrollers
Symbol
Parameter
Condition
Min
0.80VDD
Typ
Max
Unit
Sourcing 20 mA, VDD=3.0 V,
GPIO_Px_CTRL DRIVEMODE
= HIGH
V
Sinking 0.1 mA, VDD=1.98 V,
GPIO_Px_CTRL DRIVEMODE
= LOWEST
0.20VDD
0.10VDD
0.10VDD
0.05VDD
V
V
V
V
V
V
V
V
Sinking 0.1 mA, VDD=3.0 V,
GPIO_Px_CTRL DRIVEMODE
= LOWEST
Sinking 1 mA, VDD=1.98 V,
GPIO_Px_CTRL DRIVEMODE
= LOW
Sinking 1 mA, VDD=3.0 V,
GPIO_Px_CTRL DRIVEMODE
= LOW
Output low voltage
(Production test
condition = 3.0V,
DRIVEMODE =
STANDARD)
VIOOL
Sinking 6 mA, VDD=1.98 V,
GPIO_Px_CTRL DRIVEMODE
= STANDARD
0.30VDD
Sinking 6 mA, VDD=3.0 V,
GPIO_Px_CTRL DRIVEMODE
= STANDARD
0.20VDD
0.35VDD
0.25VDD
Sinking 20 mA, VDD=1.98 V,
GPIO_Px_CTRL DRIVEMODE
= HIGH
Sinking 20 mA, VDD=3.0 V,
GPIO_Px_CTRL DRIVEMODE
= HIGH
IIOLEAK
Input leakage cur-
rent
High Impedance IO connected
to GROUND or Vdd
±0.1
40
±100 nA
RPU
I/O pin pull-up resis-
tor
kOhm
kOhm
Ohm
RPD
I/O pin pull-down re-
sistor
40
RIOESD
Internal ESD series
resistor
200
tIOGLITCH
Pulse width of puls-
es to be removed
by the glitch sup-
pression filter
10
50 ns
GPIO_Px_CTRL DRIVEMODE
= LOWEST and load capaci-
tance CL=12.5-25pF.
20+0.1CL
20+0.1CL
0.10VDD
250 ns
250 ns
V
tIOOF
Output fall time
GPIO_Px_CTRL DRIVEMODE
= LOW and load capacitance
CL=350-600pF
VIOHYST
I/O pin hysteresis
VDD = 1.98 - 3.8 V
(VIOTHR+ - VIOTHR-
)
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
20
...the world's most energy friendly microcontrollers
Figure 3.11. Typical Low-Level Output Current, 2V Supply Voltage
0.20
0.15
0.10
0.05
0.00
5
4
3
2
1
- 40°C
25°C
85°C
- 40°C
25°C
85°C
0
0.0
0.5
1.0
1.5
2.0
0.0
0.5
1.0
1.5
2.0
Low- Level Output Voltage [V]
Low- Level Output Voltage [V]
GPIO_Px_CTRL DRIVEMODE = LOWEST
GPIO_Px_CTRL DRIVEMODE = LOW
20
45
40
35
30
25
20
15
10
5
15
10
5
- 40°C
25°C
- 40°C
25°C
85°C
85°C
0
0.0
0
0.5
1.0
1.5
2.0
0.0
0.5
1.0
1.5
2.0
Low- Level Output Voltage [V]
Low- Level Output Voltage [V]
GPIO_Px_CTRL DRIVEMODE = STANDARD
GPIO_Px_CTRL DRIVEMODE = HIGH
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
21
...the world's most energy friendly microcontrollers
Figure 3.12. Typical High-Level Output Current, 2V Supply Voltage
0.00
–0.05
–0.10
–0.15
–0.20
0.0
–0.5
–1.0
–1.5
–2.0
–2.5
- 40°C
25°C
85°C
- 40°C
25°C
85°C
0.0
0.5
1.0
1.5
2.0
0.0
0.5
1.0
1.5
2.0
High- Level Output Voltage [V]
High- Level Output Voltage [V]
GPIO_Px_CTRL DRIVEMODE = LOWEST
GPIO_Px_CTRL DRIVEMODE = LOW
0
0
- 40°C
- 40°C
25°C
85°C
25°C
85°C
–10
–20
–30
–40
–50
–5
–10
–15
–20
0.0
0.5
1.0
1.5
2.0
0.0
0.5
1.0
1.5
2.0
High- Level Output Voltage [V]
High- Level Output Voltage [V]
GPIO_Px_CTRL DRIVEMODE = STANDARD
GPIO_Px_CTRL DRIVEMODE = HIGH
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
22
...the world's most energy friendly microcontrollers
Figure 3.13. Typical Low-Level Output Current, 3V Supply Voltage
0.5
0.4
0.3
0.2
0.1
0.0
10
8
6
4
2
- 40°C
25°C
85°C
- 40°C
25°C
85°C
0
0.0
0.5
1.0
1.5
2.0
2.5
3.0
0.0
0.5
1.0
1.5
2.0
2.5
3.0
Low- Level Output Voltage [V]
Low- Level Output Voltage [V]
GPIO_Px_CTRL DRIVEMODE = LOWEST
GPIO_Px_CTRL DRIVEMODE = LOW
40
35
30
25
20
15
10
50
40
30
20
10
0
5
- 40°C
- 40°C
25°C
85°C
25°C
85°C
0
0.0
0.5
1.0
1.5
2.0
2.5
3.0
0.0
0.5
1.0
1.5
2.0
2.5
3.0
Low- Level Output Voltage [V]
Low- Level Output Voltage [V]
GPIO_Px_CTRL DRIVEMODE = STANDARD
GPIO_Px_CTRL DRIVEMODE = HIGH
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
23
...the world's most energy friendly microcontrollers
Figure 3.14. Typical High-Level Output Current, 3V Supply Voltage
0.0
–0.1
–0.2
–0.3
–0.4
–0.5
0
- 40°C
25°C
85°C
- 40°C
25°C
85°C
–1
–2
–3
–4
–5
–6
0.0
0.5
1.0
1.5
2.0
2.5
3.0
0.0
0.5
1.0
1.5
2.0
2.5
3.0
High- Level Output Voltage [V]
High- Level Output Voltage [V]
GPIO_Px_CTRL DRIVEMODE = LOWEST
GPIO_Px_CTRL DRIVEMODE = LOW
0
0
- 40°C
- 40°C
25°C
85°C
25°C
85°C
–10
–20
–30
–40
–50
–10
–20
–30
–40
–50
0.0
0.5
1.0
1.5
2.0
2.5
3.0
0.0
0.5
1.0
1.5
2.0
2.5
3.0
High- Level Output Voltage [V]
High- Level Output Voltage [V]
GPIO_Px_CTRL DRIVEMODE = STANDARD
GPIO_Px_CTRL DRIVEMODE = HIGH
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
24
...the world's most energy friendly microcontrollers
Figure 3.15. Typical Low-Level Output Current, 3.8V Supply Voltage
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
14
12
10
8
6
4
2
- 40°C
25°C
85°C
- 40°C
25°C
85°C
0
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
Low- Level Output Voltage [V]
Low- Level Output Voltage [V]
GPIO_Px_CTRL DRIVEMODE = LOWEST
GPIO_Px_CTRL DRIVEMODE = LOW
50
40
30
20
10
50
40
30
20
10
0
- 40°C
25°C
- 40°C
25°C
85°C
85°C
0
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
Low- Level Output Voltage [V]
Low- Level Output Voltage [V]
GPIO_Px_CTRL DRIVEMODE = STANDARD
GPIO_Px_CTRL DRIVEMODE = HIGH
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
25
...the world's most energy friendly microcontrollers
Figure 3.16. Typical High-Level Output Current, 3.8V Supply Voltage
0.0
–0.1
–0.2
–0.3
–0.4
–0.5
–0.6
–0.7
–0.8
0
- 40°C
25°C
85°C
- 40°C
25°C
85°C
–1
–2
–3
–4
–5
–6
–7
–8
–9
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
High- Level Output Voltage [V]
High- Level Output Voltage [V]
GPIO_Px_CTRL DRIVEMODE = LOWEST
GPIO_Px_CTRL DRIVEMODE = LOW
0
0
- 40°C
- 40°C
25°C
85°C
25°C
85°C
–10
–20
–30
–40
–50
–10
–20
–30
–40
–50
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
High- Level Output Voltage [V]
High- Level Output Voltage [V]
GPIO_Px_CTRL DRIVEMODE = STANDARD
GPIO_Px_CTRL DRIVEMODE = HIGH
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
26
...the world's most energy friendly microcontrollers
3.9 Oscillators
3.9.1 LFXO
Table 3.9. LFXO
Symbol
Parameter
Condition
Min
Typ
Max
Unit
fLFXO
Supported nominal
crystal frequency
32.768
30
kHz
ESRLFXO
Supported crystal
equivalent series re-
sistance (ESR)
120 kOhm
CLFXOL
Supported crystal
external load range
X1
25 pF
nA
ILFXO
Current consump-
tion for core and
buffer after startup.
ESR=30 kOhm, CL=10 pF,
LFXOBOOST in CMU_CTRL is
1
190
400
tLFXO
Start- up time.
ESR=30 kOhm, CL=10 pF,
40% - 60% duty cycle has
been reached, LFXOBOOST in
CMU_CTRL is 1
ms
1See Minimum Load Capacitance (CLFXOL) Requirement For Safe Crystal Startup in energyAware Designer in Simplicity Studio
For safe startup of a given crystal, the energyAware Designer in Simplicity Studio contains a tool to help
users configure both load capacitance and software settings for using the LFXO. For details regarding
the crystal configuration, the reader is referred to application note "AN0016 EFM32 Oscillator Design
Consideration".
3.9.2 HFXO
Table 3.10. HFXO
Symbol
Parameter
Condition
Min
Typ
Max
Unit
fHFXO
Supported nominal
crystal Frequency
4
48 MHz
Crystal frequency 48 MHz
50 Ohm
60 Ohm
1500 Ohm
mS
Supported crystal
ESRHFXO
equivalent series re- Crystal frequency 32 MHz
30
sistance (ESR)
Crystal frequency 4 MHz
400
gmHFXO
The transconduc-
tance of the HFXO
input transistor at
crystal startup
HFXOBOOST in CMU_CTRL
equals 0b11
20
5
CHFXOL
Supported crystal
external load range
25 pF
µA
4 MHz: ESR=400 Ohm,
CL=20 pF, HFXOBOOST in
CMU_CTRL equals 0b11
85
165
400
Current consump-
tion for HFXO after
startup
IHFXO
32 MHz: ESR=30 Ohm,
CL=10 pF, HFXOBOOST in
CMU_CTRL equals 0b11
µA
µs
tHFXO
Startup time
32 MHz: ESR=30 Ohm,
CL=10 pF, HFXOBOOST in
CMU_CTRL equals 0b11
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
27
...the world's most energy friendly microcontrollers
3.9.3 LFRCO
Table 3.11. LFRCO
Symbol
Parameter
Condition
Min
Typ
Max
Unit
fLFRCO
Oscillation frequen-
cy , VDD= 3.0 V,
TAMB=25°C
31.29
32.768
150
34.28 kHz
tLFRCO
Startup time not in-
cluding software
calibration
µs
ILFRCO
Current consump-
tion
300
1.5
nA
%
TUNESTEPL- Frequency step
for LSB change in
FRCO
TUNING value
Figure 3.17. Calibrated LFRCO Frequency vs Temperature and Supply Voltage
42
40
38
36
34
32
30
42
40
38
36
34
32
30
- 40°C
25°C
85°C
2.0 V
3.0 V
3.8 V
2.0
2.2
2.4
2.6
2.8
3.0
3.2
3.4
3.6
3.8
–40
–15
5
25
45
65
85
Vdd [V]
Temperature [°C]
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
28
...the world's most energy friendly microcontrollers
3.9.4 HFRCO
Table 3.12. HFRCO
Symbol
Parameter
Condition
Min
Typ
Max
Unit
28.5 MHz
21.4 MHz
14.3 MHz
11.2 MHz
6.72 MHz
1.25 MHz
28 MHz frequency band
21 MHz frequency band
14 MHz frequency band
11 MHz frequency band
7 MHz frequency band
1 MHz frequency band
fHFRCO = 14 MHz
27.5
20.6
13.7
10.8
6.48
1.15
28.0
21.0
14.0
11.0
6.60
1.20
0.6
Oscillation frequen-
cy, VDD= 3.0 V,
TAMB=25°C
fHFRCO
tHFRCO_settling Settling time after
start-up
Cycles
fHFRCO = 28 MHz
fHFRCO = 21 MHz
fHFRCO = 14 MHz
fHFRCO = 11 MHz
fHFRCO = 6.6 MHz
fHFRCO = 1.2 MHz
fHFRCO = 14 MHz
165
134
106
94
215 µA
175 µA
140 µA
125 µA
105 µA
40 µA
Current consump-
tion
IHFRCO
77
25
DCHFRCO
Duty cycle
48.5
50
51
%
%
TUNESTEPH- Frequency step
0.31
for LSB change in
FRCO
TUNING value
1The TUNING field in the CMU_HFRCOCTRL register may be used to adjust the HFRCO frequency. There is enough adjustment
range to ensure that the frequency bands above 7 MHz will always have some overlap across supply voltage and temperature. By
using a stable frequency reference such as the LFXO or HFXO, a firmware calibration routine can vary the TUNING bits and the
frequency band to maintain the HFRCO frequency at any arbitrary value between 7 MHz and 28 MHz across operating conditions.
Figure 3.18. Calibrated HFRCO 1 MHz Band Frequency vs Supply Voltage and Temperature
1.45
1.40
1.35
1.30
1.25
1.20
1.15
1.10
1.05
1.45
1.40
1.35
1.30
1.25
1.20
1.15
1.10
1.05
- 40°C
25°C
85°C
2.0 V
3.0 V
3.8 V
2.0
2.2
2.4
2.6
2.8
3.0
3.2
3.4
3.6
3.8
–40
–15
5
25
45
65
85
Vdd [V]
Temperature [°C]
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
29
...the world's most energy friendly microcontrollers
Figure 3.19. Calibrated HFRCO 7 MHz Band Frequency vs Supply Voltage and Temperature
6.70
6.65
6.60
6.55
6.50
6.45
6.40
6.35
6.30
6.70
6.65
6.60
6.55
6.50
6.45
6.40
6.35
6.30
- 40°C
25°C
85°C
2.0 V
3.0 V
3.8 V
2.0
2.2
2.4
2.6
2.8
3.0
3.2
3.4
3.6
3.8
–40
–15
5
25
45
65
85
Vdd [V]
Temperature [°C]
Figure 3.20. Calibrated HFRCO 11 MHz Band Frequency vs Supply Voltage and Temperature
11.2
11.1
11.0
10.9
10.8
10.7
10.6
11.2
11.1
11.0
10.9
10.8
10.7
10.6
- 40°C
25°C
85°C
2.0 V
3.0 V
3.8 V
2.0
2.2
2.4
2.6
2.8
3.0
3.2
3.4
3.6
3.8
–40
–15
5
25
45
65
85
Vdd [V]
Temperature [°C]
Figure 3.21. Calibrated HFRCO 14 MHz Band Frequency vs Supply Voltage and Temperature
14.2
14.1
14.0
13.9
13.8
13.7
13.6
13.5
13.4
14.2
14.1
14.0
13.9
13.8
13.7
13.6
13.5
13.4
- 40°C
25°C
85°C
2.0 V
3.0 V
3.8 V
2.0
2.2
2.4
2.6
2.8
3.0
3.2
3.4
3.6
3.8
–40
–15
5
25
45
65
85
Vdd [V]
Temperature [°C]
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
30
...the world's most energy friendly microcontrollers
Figure 3.22. Calibrated HFRCO 21 MHz Band Frequency vs Supply Voltage and Temperature
21.2
21.0
20.8
20.6
20.4
20.2
21.2
21.0
20.8
20.6
20.4
20.2
- 40°C
25°C
85°C
2.0 V
3.0 V
3.8 V
2.0
2.2
2.4
2.6
2.8
3.0
3.2
3.4
3.6
3.8
–40
–15
5
25
45
65
85
Vdd [V]
Temperature [°C]
Figure 3.23. Calibrated HFRCO 28 MHz Band Frequency vs Supply Voltage and Temperature
28.2
28.0
27.8
27.6
27.4
27.2
27.0
26.8
28.4
28.2
28.0
27.8
27.6
27.4
27.2
27.0
26.8
- 40°C
25°C
85°C
2.0 V
3.0 V
3.8 V
2.0
2.2
2.4
2.6
2.8
3.0
3.2
3.4
3.6
3.8
–40
–15
5
25
45
65
85
Vdd [V]
Temperature [°C]
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
31
...the world's most energy friendly microcontrollers
3.9.5 AUXHFRCO
Table 3.13. AUXHFRCO
Symbol
Parameter
Condition
Min
Typ
Max
Unit
28.5 MHz
21.4 MHz
14.3 MHz
11.2 MHz
6.72 MHz
1.25 MHz
28 MHz frequency band
21 MHz frequency band
14 MHz frequency band
11 MHz frequency band
7 MHz frequency band
1 MHz frequency band
fAUXHFRCO = 14 MHz
27.5
20.6
13.7
10.8
6.48
1.15
28.0
21.0
14.0
11.0
6.60
1.20
0.6
Oscillation frequen-
cy, VDD= 3.0 V,
TAMB=25°C
fAUXHFRCO
tAUXHFRCO_settlingSettling time after
start-up
Cycles
DCAUXHFRCO
Duty cycle
fAUXHFRCO = 14 MHz
48.5
50
51 %
TUNESTEPAUX-Frequency step
0.31
%
for LSB change in
HFRCO
TUNING value
1The TUNING field in the CMU_AUXHFRCOCTRL register may be used to adjust the AUXHFRCO frequency. There is enough
adjustment range to ensure that the frequency bands above 7 MHz will always have some overlap across supply voltage and
temperature. By using a stable frequency reference such as the LFXO or HFXO, a firmware calibration routine can vary the
TUNING bits and the frequency band to maintain the AUXHFRCO frequency at any arbitrary value between 7 MHz and 28 MHz
across operating conditions.
3.9.6 ULFRCO
Table 3.14. ULFRCO
Symbol
Parameter
Condition
Min
Typ
Max
Unit
fULFRCO
Oscillation frequen- 25°C, 3V
cy
0.7
1.75 kHz
TCULFRCO
Temperature coeffi-
cient
0.05
%/°C
%/V
VCULFRCO
Supply voltage co-
efficient
-18.2
3.10 Analog Digital Converter (ADC)
Table 3.15. ADC
Symbol
VADCIN
Parameter
Condition
Single ended
Differential
Min
Typ
Max
Unit
0
-VREF/2
1.25
VREF
VREF/2
VDD
V
V
V
Input voltage range
VADCREFIN
Input range of exter-
nal reference volt-
age, single ended
and differential
VADCREFIN_CH7 Input range of ex-
ternal negative ref-
erence voltage on
See VADCREFIN
0
VDD - 1.1
V
V
channel 7
VADCREFIN_CH6 Input range of ex-
ternal positive ref-
See VADCREFIN
0.625
VDD
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
32
...the world's most energy friendly microcontrollers
Symbol
Parameter
Condition
Min
Typ
Max
Unit
erence voltage on
channel 6
VADCCMIN
Common mode in-
put range
0
VDD
V
IADCIN
Input current
2pF sampling capacitors
<100
65
nA
dB
CMRRADC
Analog input com-
mon mode rejection
ratio
1 MSamples/s, 12 bit, external
reference
351
67
µA
µA
10 kSamples/s 12 bit, internal
1.25 V reference, WARMUP-
MODE in ADCn_CTRL set to
0b00
Average active cur-
rent
10 kSamples/s 12 bit, internal
1.25 V reference, WARMUP-
MODE in ADCn_CTRL set to
0b01
63
64
µA
µA
µA
IADC
10 kSamples/s 12 bit, internal
1.25 V reference, WARMUP-
MODE in ADCn_CTRL set to
0b10
IADCREF
Current consump-
tion of internal volt-
age reference
Internal voltage reference
65
2
CADCIN
RADCIN
RADCFILT
Input capacitance
pF
Input ON resistance
1
MOhm
kOhm
Input RC filter resis-
tance
10
CADCFILT
Input RC filter/de-
coupling capaci-
tance
250
fF
fADCCLK
ADC Clock Fre-
quency
13 MHz
6 bit
7
11
13
1
ADC-
CLK
Cycles
8 bit
ADC-
CLK
Cycles
tADCCONV
Conversion time
Acquisition time
12 bit
ADC-
CLK
Cycles
tADCACQ
Programmable
256 ADC-
CLK
Cycles
tADCACQVDD3
Required acquisi-
tion time for VDD/3
reference
2
µs
Startup time of ref-
erence generator
5
µs
tADCSTART
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
33
...the world's most energy friendly microcontrollers
Symbol
Parameter
Condition
Min
Typ
Max
Unit
and ADC core in
NORMAL mode
Startup time of ref-
erence generator
and ADC core in
KEEPADCWARM
mode
1
µs
1 MSamples/s, 12 bit, single
ended, internal 1.25V refer-
ence
59
dB
1 MSamples/s, 12 bit, single
ended, internal 2.5V reference
63
65
60
65
54
67
69
62
dB
dB
dB
dB
dB
dB
dB
dB
1 MSamples/s, 12 bit, single
ended, VDD reference
1 MSamples/s, 12 bit, differen-
tial, internal 1.25V reference
1 MSamples/s, 12 bit, differen-
tial, internal 2.5V reference
1 MSamples/s, 12 bit, differen-
tial, 5V reference
1 MSamples/s, 12 bit, differen-
tial, VDD reference
1 MSamples/s, 12 bit, differen-
tial, 2xVDD reference
Signal to Noise Ra-
tio (SNR)
SNRADC
200 kSamples/s, 12 bit, sin-
gle ended, internal 1.25V refer-
ence
200 kSamples/s, 12 bit, single
ended, internal 2.5V reference
63
67
63
66
66
66
70
58
dB
dB
dB
dB
dB
dB
dB
dB
200 kSamples/s, 12 bit, single
ended, VDD reference
200 kSamples/s, 12 bit, differ-
ential, internal 1.25V reference
200 kSamples/s, 12 bit, differ-
ential, internal 2.5V reference
200 kSamples/s, 12 bit, differ-
ential, 5V reference
200 kSamples/s, 12 bit, differ-
ential, VDD reference
63
200 kSamples/s, 12 bit, differ-
ential, 2xVDD reference
1 MSamples/s, 12 bit, single
ended, internal 1.25V refer-
ence
1 MSamples/s, 12 bit, single
ended, internal 2.5V reference
62
64
60
dB
dB
dB
SIgnal-to-Noise
And Distortion-ratio
(SINAD)
SINADADC
1 MSamples/s, 12 bit, single
ended, VDD reference
1 MSamples/s, 12 bit, differen-
tial, internal 1.25V reference
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
34
...the world's most energy friendly microcontrollers
Symbol
Parameter
Condition
Min
Typ
Max
Unit
1 MSamples/s, 12 bit, differen-
tial, internal 2.5V reference
64
54
66
68
61
dB
1 MSamples/s, 12 bit, differen-
tial, 5V reference
dB
dB
dB
dB
1 MSamples/s, 12 bit, differen-
tial, VDD reference
1 MSamples/s, 12 bit, differen-
tial, 2xVDD reference
200 kSamples/s, 12 bit, sin-
gle ended, internal 1.25V refer-
ence
200 kSamples/s, 12 bit, single
ended, internal 2.5V reference
65
66
63
66
66
66
69
64
dB
dB
dB
dB
dB
dB
dB
dBc
200 kSamples/s, 12 bit, single
ended, VDD reference
200 kSamples/s, 12 bit, differ-
ential, internal 1.25V reference
200 kSamples/s, 12 bit, differ-
ential, internal 2.5V reference
200 kSamples/s, 12 bit, differ-
ential, 5V reference
200 kSamples/s, 12 bit, differ-
ential, VDD reference
62
200 kSamples/s, 12 bit, differ-
ential, 2xVDD reference
1 MSamples/s, 12 bit, single
ended, internal 1.25V refer-
ence
1 MSamples/s, 12 bit, single
ended, internal 2.5V reference
76
73
66
77
76
75
69
75
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
1 MSamples/s, 12 bit, single
ended, VDD reference
1 MSamples/s, 12 bit, differen-
tial, internal 1.25V reference
1 MSamples/s, 12 bit, differen-
tial, internal 2.5V reference
Spurious-Free Dy-
namic Range (SF-
DR)
1 MSamples/s, 12 bit, differen-
tial, VDD reference
SFDRADC
1 MSamples/s, 12 bit, differen-
tial, 2xVDD reference
1 MSamples/s, 12 bit, differen-
tial, 5V reference
200 kSamples/s, 12 bit, sin-
gle ended, internal 1.25V refer-
ence
200 kSamples/s, 12 bit, single
ended, internal 2.5V reference
75
76
dBc
dBc
200 kSamples/s, 12 bit, single
ended, VDD reference
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
35
...the world's most energy friendly microcontrollers
Symbol
Parameter
Condition
Min
Typ
Max
Unit
200 kSamples/s, 12 bit, differ-
ential, internal 1.25V reference
79
79
78
79
79
dBc
200 kSamples/s, 12 bit, differ-
ential, internal 2.5V reference
dBc
dBc
dBc
dBc
200 kSamples/s, 12 bit, differ-
ential, 5V reference
200 kSamples/s, 12 bit, differ-
ential, VDD reference
68
200 kSamples/s, 12 bit, differ-
ential, 2xVDD reference
After calibration, single ended
After calibration, differential
-3.5
0.3
0.3
3
mV
VADCOFFSET
Offset voltage
mV
-1.92
-6.3
mV/°C
Thermometer out-
put gradient
ADC
Codes/
°C
TGRADADCTH
DNLADC
INLADC
Differential non-lin-
earity (DNL)
-1
±0.7
±1.2
4
LSB
Integral non-linear-
ity (INL), End point
method
±3 LSB
MCADC
No missing codes
11.9991
12
0.012
0.012
0.22
bits
1.25V reference
2.5V reference
1.25V reference
2.5V reference
0.0333 %/°C
0.033 %/°C
0.73 LSB/°C
0.623 LSB/°C
GAINED
Gain error drift
OFFSETED
Offset error drift
0.22
1On the average every ADC will have one missing code, most likely to appear around 2048 +/- n*512 where n can be a value in
the set {-3, -2, -1, 1, 2, 3}. There will be no missing code around 2048, and in spite of the missing code the ADC will be monotonic
at all times so that a response to a slowly increasing input will always be a slowly increasing output. Around the one code that is
missing, the neighbour codes will look wider in the DNL plot. The spectra will show spurs on the level of -78dBc for a full scale
input for chips that have the missing code issue.
2Typical numbers given by abs(Mean) / (85 - 25).
3Max number given by (abs(Mean) + 3x stddev) / (85 - 25).
The integral non-linearity (INL) and differential non-linearity parameters are explained in Figure 3.24 (p.
37) and Figure 3.25 (p. 37) , respectively.
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
36
...the world's most energy friendly microcontrollers
Figure 3.24. Integral Non-Linearity (INL)
Digital ouput code
INL= |[(VD- VSS)/ VLSBIDEAL] - D| where 0 < D < 2N - 1
4095
4094
4093
4092
Actual ADC
tranfer function
before offset and
gain correction
Actual ADC
tranfer function
after offset and
gain correction
INL Error
(End Point INL)
Ideal transfer
curve
3
2
1
0
VOFFSET
Analog Input
Figure 3.25. Differential Non-Linearity (DNL)
Digital
ouput
DNL= |[(VD+ 1 - VD)/ VLSBIDEAL] - 1| where 0 < D < 2N - 2
code
4095
4094
4093
4092
Full Scale Range
Example: Adjacent
input value VD+ 1
corrresponds to digital
output code D+ 1
Actual transfer
function with one
missing code.
Example: Input value
VD corrresponds to
digital output code D
Code width = 2 LSB
DNL= 1 LSB
Ideal transfer
curve
0.5
LSB
Ideal spacing
between two
adjacent codes
VLSBIDEAL= 1 LSB
5
4
3
2
1
0
Ideal 50%
Transition Point
Ideal Code Center
Analog Input
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
37
...the world's most energy friendly microcontrollers
3.10.1 Typical performance
Figure 3.26. ADC Frequency Spectrum, Vdd = 3V, Temp = 25°C
1.25V Reference
2XVDDVSS Reference
VDD Reference
2.5V Reference
5VDIFF Reference
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
38
...the world's most energy friendly microcontrollers
Figure 3.27. ADC Integral Linearity Error vs Code, Vdd = 3V, Temp = 25°C
1.25V Reference
2.5V Reference
2XVDDVSS Reference
5VDIFF Reference
VDD Reference
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
39
...the world's most energy friendly microcontrollers
Figure 3.28. ADC Differential Linearity Error vs Code, Vdd = 3V, Temp = 25°C
1.25V Reference
2.5V Reference
2XVDDVSS Reference
5VDIFF Reference
VDD Reference
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
40
...the world's most energy friendly microcontrollers
Figure 3.29. ADC Absolute Offset, Common Mode = Vdd /2
5
4
3
2
1
0
2.0
1.5
Vref= 1V25
VRef= 1V25
Vref= 2V5
VRef= 2V5
Vref= 2XVDDVSS
Vref= 5VDIFF
Vref= VDD
VRef= 2XVDDVSS
VRef= 5VDIFF
VRef= VDD
1.0
0.5
–1
0.0
–2
–3
–4
–0.5
–1.0
2.0
2.2
2.4
2.6
2.8
3.0
3.2
3.4
3.6
3.8
–40
–15
5
25
45
65
85
Vdd (V)
Temp (C)
Offset vs Supply Voltage, Temp = 25°C
Offset vs Temperature, Vdd = 3V
Figure 3.30. ADC Dynamic Performance vs Temperature for all ADC References, Vdd = 3V
71
70
69
68
67
66
65
64
63
79.4
79.2
79.0
78.8
78.6
78.4
78.2
78.0
2XVDDV
Vdd
1V25
Vdd
2V5
5VDIFF
2V5
2XVDDV
5VDIFF
1V25
–40
–15
5
25
45
65
85
–40
–15
5
25
45
65
85
Temperature [°C]
Temperature [°C]
Signal to Noise Ratio (SNR)
Spurious-Free Dynamic Range (SFDR)
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
41
...the world's most energy friendly microcontrollers
Figure 3.31. ADC Temperature sensor readout
2600
2500
2400
2300
2200
2100
Vdd= 2.0
Vdd= 3.0
Vdd= 3.8
–40
–25 –15 –5
5
15 25 35 45 55 65 75 85
Temperature [°C]
3.11 Digital Analog Converter (DAC)
Table 3.16. DAC
Symbol
VDACOUT
VDACCM
Parameter
Condition
Min
Typ
Max
Unit
VDD voltage reference, single
ended
0
-VDD
0
VDD
VDD
VDD
V
Output voltage
range
VDD voltage reference, differ-
ential
V
V
Output common
mode voltage range
500 kSamples/s, 12 bit
4001
2001
171
µA
µA
µA
Active current in-
cluding references
for 2 channels
IDAC
100 kSamples/s, 12 bit
1 kSamples/s 12 bit NORMAL
SRDAC
Sample rate
500 ksam-
ples/s
Continuous Mode
Sample/Hold Mode
Sample/Off Mode
1000 kHz
250 kHz
250 kHz
DAC clock frequen-
cy
fDAC
CYCDACCONV Clock cyckles per
conversion
2
tDACCONV
Conversion time
Settling time
2
µs
µs
dB
tDACSETTLE
5
500 kSamples/s, 12 bit, sin-
gle ended, internal 1.25V refer-
ence
58
Signal to Noise Ra-
tio (SNR)
500 kSamples/s, 12 bit, single
ended, internal 2.5V reference
59
58
dB
dB
SNRDAC
500 kSamples/s, 12 bit, differ-
ential, internal 1.25V reference
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
42
...the world's most energy friendly microcontrollers
Symbol
Parameter
Condition
Min
Typ
Max
Unit
500 kSamples/s, 12 bit, differ-
ential, internal 2.5V reference
58
59
57
dB
500 kSamples/s, 12 bit, differ-
ential, VDD reference
dB
dB
500 kSamples/s, 12 bit, sin-
gle ended, internal 1.25V refer-
ence
500 kSamples/s, 12 bit, single
ended, internal 2.5V reference
54
56
53
55
62
dB
dB
dB
dB
dBc
Signal to Noise-
SNDRDAC
pulse Distortion Ra- 500 kSamples/s, 12 bit, differ-
tio (SNDR)
ential, internal 1.25V reference
500 kSamples/s, 12 bit, differ-
ential, internal 2.5V reference
500 kSamples/s, 12 bit, differ-
ential, VDD reference
500 kSamples/s, 12 bit, sin-
gle ended, internal 1.25V refer-
ence
500 kSamples/s, 12 bit, single
ended, internal 2.5V reference
56
61
55
60
dBc
dBc
dBc
dBc
Spurious-Free
Dynamic
Range(SFDR)
SFDRDAC
500 kSamples/s, 12 bit, differ-
ential, internal 1.25V reference
500 kSamples/s, 12 bit, differ-
ential, internal 2.5V reference
500 kSamples/s, 12 bit, differ-
ential, VDD reference
After calibration, single ended
After calibration, differential
2
2
9
mV
mV
LSB
VDACOFFSET
DNLDAC
INLDAC
Offset voltage
Differential non-lin-
earity
±1
Integral non-lineari-
ty
±5
12
LSB
bits
MCDAC
No missing codes
1Measured with a static input code and no loading on the output.
3.12 Operational Amplifier (OPAMP)
The electrical characteristics for the Operational Amplifiers are based on simulations.
Table 3.17. OPAMP
Symbol
Parameter
Condition
Min
Typ
Max
Unit
(OPA2)BIASPROG=0xF,
(OPA2)HALFBIAS=0x0, Unity
Gain
370
95
460 µA
IOPAMP
Active Current
(OPA2)BIASPROG=0x7,
(OPA2)HALFBIAS=0x1, Unity
Gain
135 µA
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
43
...the world's most energy friendly microcontrollers
Symbol
Parameter
Condition
Min
Typ
Max
Unit
25 µA
(OPA2)BIASPROG=0x0,
(OPA2)HALFBIAS=0x1, Unity
Gain
13
(OPA2)BIASPROG=0xF,
(OPA2)HALFBIAS=0x0
101
98
dB
(OPA2)BIASPROG=0x7,
(OPA2)HALFBIAS=0x1
dB
GOL
Open Loop Gain
(OPA2)BIASPROG=0x0,
(OPA2)HALFBIAS=0x1
91
dB
(OPA2)BIASPROG=0xF,
(OPA2)HALFBIAS=0x0
6.1
1.8
0.25
64
MHz
MHz
MHz
°
Gain Bandwidth
Product
(OPA2)BIASPROG=0x7,
(OPA2)HALFBIAS=0x1
GBWOPAMP
(OPA2)BIASPROG=0x0,
(OPA2)HALFBIAS=0x1
(OPA2)BIASPROG=0xF,
(OPA2)HALFBIAS=0x0, CL=75
pF
(OPA2)BIASPROG=0x7,
(OPA2)HALFBIAS=0x1, CL=75
pF
58
58
°
°
PMOPAMP
Phase Margin
(OPA2)BIASPROG=0x0,
(OPA2)HALFBIAS=0x1, CL=75
pF
RINPUT
RLOAD
Input Resistance
Load Resistance
DC Load Current
100
Mohm
Ohm
200
ILOAD_DC
11 mA
OPAxHCMDIS=0
OPAxHCMDIS=1
VSS
VSS
VSS
-13
VDD
V
V
V
VINPUT
Input Voltage
VDD-1.2
VDD
VOUTPUT
Output Voltage
Unity Gain, VSS<Vin<VDD
OPAxHCMDIS=0
,
0
1
11 mV
VOFFSET
Input Offset Voltage
Unity Gain, VSS<Vin<DD-1.2,
OPAxHCMDIS=1
mV
VOFFSET_DRIFT Input Offset Voltage
Drift
0.02 mV/°C
V/µs
(OPA2)BIASPROG=0xF,
(OPA2)HALFBIAS=0x0
3.2
0.8
0.1
101
(OPA2)BIASPROG=0x7,
(OPA2)HALFBIAS=0x1
V/µs
SROPAMP
Slew Rate
(OPA2)BIASPROG=0x0,
(OPA2)HALFBIAS=0x1
V/µs
Vout=1V, RESSEL=0,
0.1 Hz<f<10 kHz, OPAx-
HCMDIS=0
µVRMS
NOPAMP
Voltage Noise
Vout=1V, RESSEL=0,
0.1 Hz<f<10 kHz, OPAx-
HCMDIS=1
141
µVRMS
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
44
...the world's most energy friendly microcontrollers
Symbol
Parameter
Condition
Min
Typ
Max
Unit
Vout=1V, RESSEL=0, 0.1
Hz<f<1 MHz, OPAxHCMDIS=0
196
229
µVRMS
Vout=1V, RESSEL=0, 0.1
Hz<f<1 MHz, OPAxHCMDIS=1
µVRMS
µVRMS
µVRMS
µVRMS
µVRMS
RESSEL=7, 0.1 Hz<f<10 kHz,
OPAxHCMDIS=0
1230
2130
1630
2590
RESSEL=7, 0.1 Hz<f<10 kHz,
OPAxHCMDIS=1
RESSEL=7, 0.1 Hz<f<1 MHz,
OPAxHCMDIS=0
RESSEL=7, 0.1 Hz<f<1 MHz,
OPAxHCMDIS=1
Figure 3.32. OPAMP Common Mode Rejection Ratio
Figure 3.33. OPAMP Positive Power Supply Rejection Ratio
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
45
...the world's most energy friendly microcontrollers
Figure 3.34. OPAMP Negative Power Supply Rejection Ratio
Figure 3.35. OPAMP Voltage Noise Spectral Density (Unity Gain) Vout=1V
Figure 3.36. OPAMP Voltage Noise Spectral Density (Non-Unity Gain)
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
46
...the world's most energy friendly microcontrollers
3.13 Analog Comparator (ACMP)
Table 3.18. ACMP
Symbol
VACMPIN
VACMPCM
Parameter
Condition
Min
Typ
Max
Unit
V
Input voltage range
0
0
VDD
VDD
ACMP Common
V
Mode voltage range
BIASPROG=0b0000, FULL-
BIAS=0 and HALFBIAS=1 in
ACMPn_CTRL register
0.1
2.87
195
0
0.4 µA
15 µA
520 µA
µA
BIASPROG=0b1111, FULL-
BIAS=0 and HALFBIAS=0 in
ACMPn_CTRL register
IACMP
Active current
BIASPROG=0b1111, FULL-
BIAS=1 and HALFBIAS=0 in
ACMPn_CTRL register
Internal voltage reference off.
Using external voltage refer-
ence
Current consump-
tion of internal volt-
age reference
IACMPREF
Internal voltage reference
5
0
µA
VACMPOFFSET Offset voltage
BIASPROG= 0b1010, FULL-
BIAS=0 and HALFBIAS=0 in
ACMPn_CTRL register
-12
12 mV
VACMPHYST
ACMP hysteresis
Programmable
17
39
mV
CSRESSEL=0b00 in
ACMPn_INPUTSEL
kOhm
CSRESSEL=0b01 in
ACMPn_INPUTSEL
71
104
136
kOhm
kOhm
kOhm
Capacitive Sense
Internal Resistance
RCSRES
CSRESSEL=0b10 in
ACMPn_INPUTSEL
CSRESSEL=0b11 in
ACMPn_INPUTSEL
tACMPSTART
Startup time
10 µs
The total ACMP current is the sum of the contributions from the ACMP and its internal voltage reference
as given in Equation 3.1 (p. 47) . IACMPREF is zero if an external voltage reference is used.
Total ACMP Active Current
IACMPTOTAL = IACMP + IACMPREF
(3.1)
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
47
...the world's most energy friendly microcontrollers
Figure 3.37. ACMP Characteristics, Vdd = 3V, Temp = 25°C, FULLBIAS = 0, HALFBIAS = 1
2.5
2.0
1.5
1.0
0.5
0.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0.0
HYSTSEL= 0.0
HYSTSEL= 2.0
HYSTSEL= 4.0
HYSTSEL= 6.0
0
4
8
12
0
2
4
6
8
10
12
14
ACMP_CTRL_BIASPROG
ACMP_CTRL_BIASPROG
Current consumption, HYSTSEL = 4
Response time
100
80
60
40
20
0
BIASPROG= 0.0
BIASPROG= 4.0
BIASPROG= 8.0
BIASPROG= 12.0
0
1
2
3
4
5
6
7
ACMP_CTRL_HYSTSEL
Hysteresis
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
48
...the world's most energy friendly microcontrollers
3.14 Voltage Comparator (VCMP)
Table 3.19. VCMP
Symbol
VVCMPIN
VVCMPCM
Parameter
Condition
Min
Typ
Max
Unit
V
Input voltage range
VDD
VDD
VCMP Common
V
Mode voltage range
BIASPROG=0b0000 and
HALFBIAS=1 in VCMPn_CTRL
register
0.3
22
10
0.6 µA
IVCMP
Active current
BIASPROG=0b1111 and
HALFBIAS=0 in VCMPn_CTRL
register. LPREF=0.
35 µA
µs
tVCMPREF
Startup time refer-
ence generator
NORMAL
Single ended
Differential
10
10
61
mV
mV
VVCMPOFFSET Offset voltage
VVCMPHYST
tVCMPSTART
VCMP hysteresis
Startup time
210 mV
10 µs
The VDD trigger level can be configured by setting the TRIGLEVEL field of the VCMP_CTRL register in
accordance with the following equation:
VCMP Trigger Level as a Function of Level Setting
VDD Trigger Level=1.667V+0.034 ×TRIGLEVEL
(3.2)
3.15 EBI
Figure 3.38. EBI Write Enable Timing
WRSETUP
WRSTRB
WRHOLD
(0, 1, 2, ...)
(1, 2, 3, ...)
(0, 1, 2, ...)
EBI_BL[N- 1:0]
EBI_A[N- 1:0]
EBI_AD[15:0]
EBI_CSn
Z
Z
Z
EBI_BL
tOSU_WEn
tOH_WEn
tOH_WEn
tOH_WEn
tOH_WEn
EBI_A
tOSU_WEn
DATA[15:0]
tOSU_WEn
tOSU_WEn
tWIDTH_WEn
EBI_WEn
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
49
...the world's most energy friendly microcontrollers
Table 3.20. EBI Write Enable Timing
Symbol
Parameter
Min
Typ
Max
Unit
1 2 3 4
tOH_WEn
Output hold time, from trailing EBI_WEn/
EBI_NANDWEn edge to EBI_AD, EBI_A,
EBI_CSn, EBI_BLn invalid
-6.00 + (WRHOLD *
tHFCORECLK
ns
)
1 2 3 4 5
tOSU_WEn
Output setup time, from EBI_AD, EBI_A,
EBI_CSn, EBI_BLn valid to leading EBI_WEn/
EBI_NANDWEn edge
-14.00 + (WRSETUP
* tHFCORECLK
ns
ns
)
1 2 3 4 5
tWIDTH_WEn
EBI_WEn/EBI_NANDWEn pulse width
-7.00 + ((WRSTRB
+1) * tHFCORECLK
)
1Applies for all addressing modes (figure only shows D16 addressing mode)
2Applies for both EBI_WEn and EBI_NANWEn (figure only shows EBI_WEn)
3Applies for all polarities (figure only shows active low signals)
4Measurement done at 10% and 90% of VDD (figure shows 50% of VDD
)
5 The figure shows the timing for the case that the half strobe length functionality is not used, i.e. HALFWE=0. The leading edge
of EBI_WEn can be moved to the right by setting HALFWE=1. This decreases the length of tWIDTH_WEn and increases the length
of tOSU_WEn by 1/2 * tHFCLKNODIV
.
Figure 3.39. EBI Address Latch Enable Related Output Timing
ADDRSETUP
(1, 2, 3, ...)
ADDRHOLD
(0, 1, 2, ...)
WRSETUP
(0, 1, 2, ...)
WRSTRB
(1, 2, 3, ...)
WRHOLD
(0, 1, 2, ...)
EBI_AD[15:0]
EBI_ALE
ADDR[16:1]
tWIDTH_ALEn
DATA[15:0]
Z
tWIDTH_ALEn
tOSU_ALEn
EBI_CSn
EBI_WEn
Table 3.21. EBI Address Latch Enable Related Output Timing
Symbol
Parameter
Min
Typ
Max
Unit
1 2 3 4
tOH_ALEn
Output hold time, from trailing EBI_ALE edge to
EBI_AD invalid
-6.00 + (AD-
ns
DRHOLD5 * tHFCORE-
)
CLK
1 2 4
tOSU_ALEn
Output setup time, from EBI_AD valid to leading
EBI_ALE edge
-13.00 + (0 * tHFCORE-
ns
ns
)
CLK
1 2 3 4
tWIDTH_ALEn
EBI_ALEn pulse width
-7.00 + (ADDRSET-
UP+1) * tHFCORECLK
)
1Applies to addressing modes D8A24ALE and D16A16ALE (figure only shows D16A16ALE)
2Applies for all polarities (figure only shows active low signals)
3 The figure shows the timing for the case that the half strobe length functionality is not used, i.e. HALFALE=0. The trailing edge
of EBI_ALE can be moved to the left by setting HALFALE=1. This decreases the length of tWIDTH_ALEn and increases the length
of tOH_ALEn by tHFCORECLK - 1/2 * tHFCLKNODIV
.
4Measurement done at 10% and 90% of VDD (figure shows 50% of VDD
)
5Figure only shows a write operation. For a multiplexed read operation the address hold time is controlled via the RDSETUP state
instead of via the ADDRHOLD state.
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
50
...the world's most energy friendly microcontrollers
Figure 3.40. EBI Read Enable Related Output Timing
RDSETUP
RDSTRB
RDHOLD
(0, 1, 2, ...)
(1, 2, 3, ...)
(0, 1, 2, ...)
EBI_BL[1:0]
EBI_A[27:0]
EBI_AD[15:8]
EBI_CSn
EBI_BL
tSU_REn
Z
Z
Z
tH_REn
tH_REn
tH_REn
EBI_A
tSU_REn
ADDR[7:0]
tSU_REn
tH_REn
tSU_REn
Z
EBI_AD[7:0]
EBI_REn
DATA[7:0]
Z
tWIDTH_REn
Table 3.22. EBI Read Enable Related Output Timing
Symbol
Parameter
Min
Typ
Max
Unit
1 2 3 4
tOH_REn
Output hold time, from trailing EBI_REn/
EBI_NANDREn edge to EBI_AD, EBI_A, EBI_CSn,
EBI_BLn invalid
-10.00 + (RDHOLD *
tHFCORECLK
ns
)
1 2 3 4 5
tOSU_REn
Output setup time, from EBI_AD, EBI_A, EBI_CSn,
EBI_BLn valid to leading EBI_REn/EBI_NANDREn
edge
-10.00 + (RDSETUP
* tHFCORECLK
ns
ns
)
1 2 3 4 5 6
tWIDTH_REn
EBI_REn pulse width
-9.00 + ((RD-
STRB+1) * tHFCORE-
)
CLK
1Applies for all addressing modes (figure only shows D8A8. Output timing for EBI_AD only applies to multiplexed addressing
modes D8A24ALE and D16A16ALE)
2Applies for both EBI_REn and EBI_NANDREn (figure only shows EBI_REn)
3Applies for all polarities (figure only shows active low signals)
4Measurement done at 10% and 90% of VDD (figure shows 50% of VDD
)
5The figure shows the timing for the case that the half strobe length functionality is not used, i.e. HALFRE=0. The leading edge
of EBI_REn can be moved to the right by setting HALFRE=1. This decreases the length of tWIDTH_REn and increases the length
of tOSU_REn by 1/2 * tHFCLKNODIV
.
6When page mode is used, RDSTRB is replaced by RDPA for page hits.
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
51
...the world's most energy friendly microcontrollers
Figure 3.41. EBI Read Enable Related Timing Requirements
RDSETUP
RDSTRB
RDHOLD
(0, 1, 2, ...)
(1, 2, 3, ...)
(0, 1, 2, ...)
ADDR[N:1]
Z
Z
EBI_A[N- 1:0]
EBI_AD[15:0]
EBI_CSn
DATA[15:0]
Z
tSU_REn
EBI_REn
tH_REn
Table 3.23. EBI Read Enable Related Timing Requirements
Symbol
Parameter
Min
Typ
Max
Unit
1 2 3 4
tSU_REn
Setup time, from EBI_AD valid to trailing EBI_REn
edge
37
-1
ns
1 2 3 4
tH_Ren
Hold time, from trailing EBI_REn edge to EBI_AD
invalid
ns
1Applies for all addressing modes (figure only shows D16A8).
2Applies for both EBI_REn and EBI_NANDREn (figure only shows EBI_REn)
3Applies for all polarities (figure only shows active low signals)
4Measurement done at 10% and 90% of VDD (figure shows 50% of VDD
)
Figure 3.42. EBI Ready/Wait Related Timing Requirements
RDSETUP
RDSTRB
SYNC
RDHOLD
(0, 1, 2, ...)
(1, 2, 3, ...)
(3)
(0, 1, 2, ...)
EBI_RDY
EBI_AD[15:0]
EBI_CSn
Z
DATA[15:0]
tSU_ARDY
EBI_REn
tH_ARDY
Table 3.24. EBI Ready/Wait Related Timing Requirements
Symbol
Parameter
Min
37 + (3 * tHFCORECLK
Typ
Max
Unit
1 2 3 4
tSU_ARDY
Setup time, from EBI_ARDY valid to trailing
EBI_REn, EBI_WEn edge
)
ns
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
52
...the world's most energy friendly microcontrollers
Symbol
Parameter
Min
-1 + (3 * tHFCORECLK
Typ
Max
Unit
1 2 3 4
tH_ARDY
Hold time, from trailing EBI_REn, EBI_WEn edge
to EBI_ARDY invalid
)
ns
1Applies for all addressing modes (figure only shows D16A8.)
2Applies for EBI_REn, EBI_WEn (figure only shows EBI_REn)
3Applies for all polarities (figure only shows active low signals)
4Measurement done at 10% and 90% of VDD (figure shows 50% of VDD
)
3.16 I2C
Table 3.25. I2C Standard-mode (Sm)
Symbol
fSCL
Parameter
Min
Typ
Max
Unit
SCL clock frequency
0
4.7
4.0
250
8
1001 kHz
tLOW
SCL clock low time
µs
tHIGH
SCL clock high time
µs
tSU,DAT
tHD,DAT
tSU,STA
tHD,STA
tSU,STO
tBUF
SDA set-up time
ns
SDA hold time
34502,3 ns
Repeated START condition set-up time
(Repeated) START condition hold time
STOP condition set-up time
4.7
4.0
4.0
4.7
µs
µs
µs
µs
Bus free time between a STOP and a START condi-
tion
1For the minimum HFPERCLK frequency required in Standard-mode, see the I2C chapter in the EFM32WG Reference Manual.
2The maximum SDA hold time (tHD,DAT) needs to be met only when the device does not stretch the low time of SCL (tLOW).
3When transmitting data, this number is guaranteed only when I2Cn_CLKDIV < ((3450*10-9 [s] * fHFPERCLK [Hz]) - 4).
Table 3.26. I2C Fast-mode (Fm)
Symbol
fSCL
Parameter
Min
Typ
Max
Unit
SCL clock frequency
0
1.3
0.6
100
8
4001 kHz
tLOW
SCL clock low time
µs
tHIGH
SCL clock high time
µs
tSU,DAT
tHD,DAT
tSU,STA
tHD,STA
tSU,STO
tBUF
SDA set-up time
ns
SDA hold time
9002,3 ns
Repeated START condition set-up time
(Repeated) START condition hold time
STOP condition set-up time
0.6
0.6
0.6
1.3
µs
µs
µs
µs
Bus free time between a STOP and a START condi-
tion
1For the minimum HFPERCLK frequency required in Fast-mode, see the I2C chapter in the EFM32WG Reference Manual.
2The maximum SDA hold time (tHD,DAT) needs to be met only when the device does not stretch the low time of SCL (tLOW).
3When transmitting data, this number is guaranteed only when I2Cn_CLKDIV < ((900*10-9 [s] * fHFPERCLK [Hz]) - 4).
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
53
...the world's most energy friendly microcontrollers
Table 3.27. I2C Fast-mode Plus (Fm+)
Symbol
fSCL
Parameter
Min
Typ
Max
Unit
SCL clock frequency
0
0.5
10001 kHz
tLOW
SCL clock low time
µs
µs
ns
ns
µs
µs
µs
µs
tHIGH
SCL clock high time
0.26
50
tSU,DAT
tHD,DAT
tSU,STA
tHD,STA
tSU,STO
tBUF
SDA set-up time
SDA hold time
8
Repeated START condition set-up time
(Repeated) START condition hold time
STOP condition set-up time
0.26
0.26
0.26
0.5
Bus free time between a STOP and a START condi-
tion
1For the minimum HFPERCLK frequency required in Fast-mode Plus, see the I2C chapter in the EFM32WG Reference Manual.
3.17 USART SPI
Figure 3.43. SPI Master Timing
tCS_MO
CS
tSCKL_MO
SCLK
CLKPOL = 0
tSCLK
SCLK
CLKPOL = 1
MOSI
MISO
tSU_MI
tH_MI
Table 3.28. SPI Master Timing
Symbol
Parameter
Condition
Min
2 * tHFPER-
Typ
Max
Unit
1 2
tSCLK
SCLK period
ns
CLK
1 2
tCS_MO
CS to MOSI
-2.00
2.00 ns
1 2
tSCLK_MO
SCLK to MOSI
MISO setup time
MISO hold time
-1.00
36.00
-6.00
3.00 ns
1 2
tSU_MI
IOVDD = 3.0 V
ns
ns
1 2
tH_MI
1Applies for both CLKPHA = 0 and CLKPHA = 1 (figure only shows CLKPHA = 0)
2Measurement done at 10% and 90% of VDD (figure shows 50% of VDD
)
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
54
...the world's most energy friendly microcontrollers
Table 3.29. SPI Master Timing with SSSEARLY and SMSDELAY
Symbol
Parameter
Condition
Min
2 * tHFPER-
Typ
Max
Unit
1 2
tSCLK
SCLK period
ns
CLK
12
tCS_MO
CS to MOSI
-2.00
2.00 ns
12
tSCLK_MO
SCLK to MOSI
MISO setup time
MISO hold time
-1.00
-32.00
63.00
3.00 ns
12
tSU_MI
IOVDD = 3.0 V
ns
ns
12
tH_MI
1Applies for both CLKPHA = 0 and CLKPHA = 1 (figure only shows CLKPHA = 0)
2Measurement done at 10% and 90% of VDD (figure shows 50% of VDD
)
Figure 3.44. SPI Slave Timing
tCS_ACT_MI
CS
tCS_DIS_MI
SCLK
CLKPOL = 0
tSCLK_HI
tSCLK_LO
SCLK
tSU_MO
CLKPOL = 1
tSCLK
tH_MO
MOSI
MISO
tSCLK_MI
Table 3.30. SPI Slave Timing
Symbol
Parameter
Min
Typ
Max
Unit
1 2
tSCLK_sl
tSCLK_hi
tSCLK_lo
SCKL period
6 * tHFPER-
ns
ns
ns
CLK
1 2
1 2
SCLK high period
SCLK low period
3 * tHFPER-
CLK
3 * tHFPER-
CLK
1 2
tCS_ACT_MI
CS active to MISO
CS disable to MISO
MOSI setup time
MOSI hold time
5.00
5.00
5.00
35.00 ns
35.00 ns
ns
1 2
tCS_DIS_MI
1 2
tSU_MO
1 2
tH_MO
2 + 2 * tHF-
ns
PERCLK
1 2
tSCLK_MI
SCLK to MISO
7 + tHFPER-
42 + 2 * ns
tHFPERCLK
CLK
1Applies for both CLKPHA = 0 and CLKPHA = 1 (figure only shows CLKPHA = 0)
2Measurement done at 10% and 90% of VDD (figure shows 50% of VDD
)
Table 3.31. SPI Slave Timing with SSSEARLY and SMSDELAY
Symbol
Parameter
Min
6 * tHFPER-
Typ
Max
Unit
12
tSCLK_sl
SCKL period
ns
CLK
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
55
...the world's most energy friendly microcontrollers
Symbol
Parameter
Min
3 * tHFPER-
Typ
Max
Unit
12
tSCLK_hi
SCLK high period
ns
CLK
12
tSCLK_lo
SCLK low period
3 * tHFPER-
ns
CLK
12
tCS_ACT_MI
CS active to MISO
CS disable to MISO
MOSI setup time
MOSI hold time
5.00
5.00
5.00
35.00 ns
12
tCS_DIS_MI
35.00 ns
12
tSU_MO
ns
ns
12
tH_MO
2 + 2 * tHF-
PERCLK
12
tSCLK_MI
SCLK to MISO
-264 + tHF-
-234 + 2 * ns
tHFPERCLK
PERCLK
1Applies for both CLKPHA = 0 and CLKPHA = 1 (figure only shows CLKPHA = 0)
2Measurement done at 10% and 90% of VDD (figure shows 50% of VDD
)
3.18 Digital Peripherals
Table 3.32. Digital Peripherals
Symbol
Parameter
Condition
Min
Typ
Max
Unit
IUSART
USART current
USART idle current, clock en-
abled
4.0
3.8
µA/
MHz
IUART
UART current
LEUART current
I2C current
UART idle current, clock en-
abled
µA/
MHz
ILEUART
LEUART idle current, clock en-
abled
194.0
7.6
nA
II2C
I2C idle current, clock enabled
µA/
MHz
ITIMER
ILETIMER
IPCNT
TIMER current
LETIMER current
PCNT current
TIMER_0 idle current, clock
enabled
6.5
µA/
MHz
LETIMER idle current, clock
enabled
85.8
91.4
nA
nA
nA
PCNT idle current, clock en-
abled
IRTC
IAES
RTC current
AES current
RTC idle current, clock enabled
AES idle current, clock enabled
54.6
1.8
µA/
MHz
IGPIO
GPIO current
EBI current
PRS current
DMA current
GPIO idle current, clock en-
abled
3.4
6.5
µA/
MHz
IEBI
EBI idle current, clock enabled
µA/
MHz
IPRS
PRS idle current
3.9
µA/
MHz
IDMA
Clock enable
10.9
µA/
MHz
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
56
...the world's most energy friendly microcontrollers
4 Pinout and Package
Note
Please refer to the application note "AN0002 EFM32 Hardware Design Considerations" for
guidelines on designing Printed Circuit Boards (PCB's) for the EFM32WG380.
4.1 Pinout
The EFM32WG380 pinout is shown in Figure 4.1 (p. 57) and Table 4.1 (p. 57). Alternate locations
are denoted by "#" followed by the location number (Multiple locations on the same pin are split with "/").
Alternate locations can be configured in the LOCATION bitfield in the *_ROUTE register in the module
in question.
Figure 4.1. EFM32WG380 Pinout (top view, not to scale)
Table 4.1. Device Pinout
LQFP100 Pin#
and Name
Pin Alternate Functionality / Description
Pin Name
Analog
EBI
Timers
Communication
Other
LEU0_RX #4
I2C0_SDA #0
PRS_CH0 #0
GPIO_EM4WU0
1
PA0
EBI_AD09 #0/1/2
TIM0_CC0 #0/1/4
CMU_CLK1 #0
PRS_CH1 #0
2
3
PA1
PA2
EBI_AD10 #0/1/2
EBI_AD11 #0/1/2
TIM0_CC1 #0/1
TIM0_CC2 #0/1
I2C0_SCL #0
CMU_CLK0 #0
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
57
...the world's most energy friendly microcontrollers
LQFP100 Pin#
and Name
Pin Alternate Functionality / Description
Pin Name
Analog
EBI
Timers
Communication
Other
ETM_TD0 #3
LES_ALTEX2 #0
ETM_TD1 #3
4
5
6
7
PA3
PA4
PA5
PA6
EBI_AD12 #0/1/2
EBI_AD13 #0/1/2
EBI_AD14 #0/1/2
EBI_AD15 #0/1/2
TIM0_CDTI0 #0
TIM0_CDTI1 #0
TIM0_CDTI2 #0
U0_TX #2
U0_RX #2
LES_ALTEX3 #0
ETM_TD2 #3
LES_ALTEX4 #0
ETM_TD3 #3
LEU1_TX #1
LEU1_RX #1
ETM_TCLK #3
GPIO_EM4WU1
8
9
IOVDD_0
PB0
Digital IO power supply 0.
EBI_A16 #0/1/2
EBI_A17 #0/1/2
EBI_A18 #0/1/2
EBI_A19 #0/1/2
EBI_A20 #0/1/2
EBI_A21 #0/1/2
EBI_A22 #0/1/2
TIM1_CC0 #2
TIM1_CC1 #2
TIM1_CC2 #2
PCNT1_S0IN #1
PCNT1_S1IN #1
10
11
12
13
14
15
16
17
PB1
PB2
PB3
US2_TX #1
US2_RX #1
US2_CLK #1
US2_CS #1
PB4
PB5
PB6
VSS
Ground
IOVDD_1
Digital IO power supply 1.
ACMP0_CH0
DAC0_OUT0ALT #0/
OPAMP_OUT0ALT
US0_TX #5
US1_TX #0
I2C0_SDA #4
TIM0_CC1 #4
PCNT0_S0IN #2
LES_CH0 #0
PRS_CH2 #0
18
19
20
21
22
23
PC0
PC1
PC2
PC3
PC4
PC5
EBI_A23 #0/1/2
EBI_A24 #0/1/2
ACMP0_CH1
DAC0_OUT0ALT #1/
OPAMP_OUT0ALT
US0_RX #5
US1_RX #0
I2C0_SCL #4
TIM0_CC2 #4
PCNT0_S1IN #2
LES_CH1 #0
PRS_CH3 #0
ACMP0_CH2
DAC0_OUT0ALT #2/
OPAMP_OUT0ALT
EBI_A25 #0/1/2
TIM0_CDTI0 #4
TIM0_CDTI1 #4
US2_TX #0
US2_RX #0
LES_CH2 #0
LES_CH3 #0
LES_CH4 #0
LES_CH5 #0
ACMP0_CH3
DAC0_OUT0ALT #3/
OPAMP_OUT0ALT
EBI_NANDREn #0/1/2
EBI_A26 #0/1/2
ACMP0_CH4
DAC0_P0 /
OPAMP_P0
TIM0_CDTI2 #4
LETIM0_OUT0 #3
PCNT1_S0IN #0
US2_CLK #0
I2C1_SDA #0
ACMP0_CH5
DAC0_N0 /
OPAMP_N0
LETIM0_OUT1 #3
PCNT1_S1IN #0
US2_CS #0
I2C1_SCL #0
EBI_NANDWEn #0/1/2
US0_TX #4
US1_CLK #0
24
25
PB7
PB8
LFXTAL_P
LFXTAL_N
TIM1_CC0 #3
TIM1_CC1 #3
US0_RX #4
US1_CS #0
26
27
28
29
30
31
32
PA7
PA8
EBI_CSTFT #0/1/2
EBI_DCLK #0/1/2
EBI_DTEN #0/1/2
EBI_VSNC #0/1/2
EBI_HSNC #0/1/2
TIM2_CC0 #0
TIM2_CC1 #0
TIM2_CC2 #0
PA9
PA10
PA11
IOVDD_2
VSS
Digital IO power supply 2.
Ground
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
58
...the world's most energy friendly microcontrollers
LQFP100 Pin#
and Name
Pin Alternate Functionality / Description
Pin Name
Analog
EBI
Timers
Communication
Other
33
PA12
PA13
PA14
EBI_A00 #0/1/2
EBI_A01 #0/1/2
EBI_A02 #0/1/2
TIM2_CC0 #1
TIM2_CC1 #1
TIM2_CC2 #1
34
35
Reset input, active low.
36
RESETn
To apply an external reset source to this pin, it is required to only drive this pin low during reset, and let the internal pull-up ensure
that reset is released.
37
38
PB9
EBI_A03 #0/1/2
EBI_A04 #0/1/2
U1_TX #2
U1_RX #2
PB10
DAC0_OUT0 /
OPAMP_OUT0
TIM1_CC2 #3
LETIM0_OUT0 #1
39
PB11
I2C1_SDA #1
I2C1_SCL #1
DAC0_OUT1 /
OPAMP_OUT1
40
41
42
PB12
AVDD_1
PB13
LETIM0_OUT1 #1
Analog power supply 1.
HFXTAL_P
US0_CLK #4/5
LEU0_TX #1
US0_CS #4/5
LEU0_RX #1
43
PB14
HFXTAL_N
44
45
IOVDD_3
AVDD_0
Digital IO power supply 3.
Analog power supply 0.
ADC0_CH0
DAC0_OUT0ALT #4/
OPAMP_OUT0ALT
OPAMP_OUT2 #1
46
47
PD0
PD1
PCNT2_S0IN #0
US1_TX #1
US1_RX #1
ADC0_CH1
DAC0_OUT1ALT #4/
OPAMP_OUT1ALT
TIM0_CC0 #3
PCNT2_S1IN #0
DBG_SWO #2
USB_DMPU #0
US1_CLK #1
48
49
50
51
PD2
PD3
PD4
PD5
ADC0_CH2
EBI_A27 #0/1/2
TIM0_CC1 #3
TIM0_CC2 #3
DBG_SWO #3
ETM_TD1 #0/2
ETM_TD2 #0/2
ETM_TD3 #0/2
ADC0_CH3
OPAMP_N2
US1_CS #1
LEU0_TX #0
LEU0_RX #0
ADC0_CH4
OPAMP_P2
ADC0_CH5
OPAMP_OUT2 #0
ADC0_CH6
DAC0_P1 /
OPAMP_P1
TIM1_CC0 #4
LETIM0_OUT0 #0
PCNT0_S0IN #3
LES_ALTEX0 #0
ACMP0_O #2
ETM_TD0 #0
US1_RX #2
I2C0_SDA #1
52
53
PD6
PD7
CMU_CLK0 #2
LES_ALTEX1 #0
ACMP1_O #2
ADC0_CH7
DAC0_N1 /
OPAMP_N1
TIM1_CC1 #4
LETIM0_OUT1 #0
PCNT0_S1IN #3
US1_TX #2
I2C0_SCL #1
ETM_TCLK #0
54
55
PD8
PC6
BU_VIN
CMU_CLK1 #1
LEU1_TX #0
I2C0_SDA #2
LES_CH6 #0
ETM_TCLK #2
ACMP0_CH6
EBI_A05 #0/1/2
EBI_A06 #0/1/2
LEU1_RX #0
I2C0_SCL #2
LES_CH7 #0
ETM_TD0 #2
56
PC7
ACMP0_CH7
57
58
59
VDD_DREG
VSS
Power supply for on-chip voltage regulator.
Ground
DECOUPLE
Decouple output for on-chip voltage regulator. An external capacitance of size CDECOUPLE is required at this pin.
TIM3_CC0 #1
PCNT0_S0IN #1
U0_TX #1
I2C1_SDA #2
60
PE0
EBI_A07 #0/1/2
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
59
...the world's most energy friendly microcontrollers
LQFP100 Pin#
and Name
Pin Alternate Functionality / Description
Pin Name
Analog
EBI
Timers
Communication
Other
TIM3_CC1 #1
PCNT0_S1IN #1
U0_RX #1
I2C1_SCL #2
61
PE1
EBI_A08 #0/1/2
62
63
64
65
66
67
68
PE2
PE3
PE4
PE5
PE6
PE7
PC8
BU_VOUT
BU_STAT
EBI_A09 #0
EBI_A10 #0
TIM3_CC2 #1
U1_TX #3
U1_RX #3
ACMP0_O #1
ACMP1_O #1
EBI_A11 #0/1/2
EBI_A12 #0/1/2
EBI_A13 #0/1/2
EBI_A14 #0/1/2
EBI_A15 #0/1/2
US0_CS #1
US0_CLK #1
US0_RX #1
US0_TX #1
US0_CS #2
ACMP1_CH0
ACMP1_CH1
TIM2_CC0 #2
TIM2_CC1 #2
TIM2_CC2 #2
LES_CH8 #0
LES_CH9 #0
GPIO_EM4WU2
69
PC9
EBI_A09 #1/2
US0_CLK #2
70
71
72
73
PC10
PC11
ACMP1_CH2
ACMP1_CH3
EBI_A10 #1/2
EBI_ALE #1/2
US0_RX #2
US0_TX #2
LES_CH10 #0
LES_CH11 #0
USB_VREGI
USB_VREGO
USB Input to internal 3.3 V regulator.
USB Decoupling for internal 3.3 V USB regulator and regulator output.
U1_TX #1
USB_DM
74
75
PF10
PF11
U1_RX #1
USB_DP
US1_CLK #2
LEU0_TX #3
I2C0_SDA #5
TIM0_CC0 #5
LETIM0_OUT0 #2
76
77
78
PF0
PF1
PF2
DBG_SWCLK #0/1/2/3
US1_CS #2
LEU0_RX #3
I2C0_SCL #5
TIM0_CC1 #5
LETIM0_OUT1 #2
DBG_SWDIO #0/1/2/3
GPIO_EM4WU3
ACMP1_O #0
DBG_SWO #0
GPIO_EM4WU4
EBI_ARDY #0/1/2
EBI_REn #0/2
TIM0_CC2 #5
LEU0_TX #4
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
USB_VBUS
PF12
PF5
USB 5.0 V VBUS input.
USB_ID
TIM0_CDTI2 #2/5
USB_VBUSEN #0
PRS_CH2 #1
IOVDD_5
VSS
Digital IO power supply 5.
Ground
PF6
EBI_BL0 #0/1/2
EBI_BL1 #0/1/2
EBI_WEn #1
TIM0_CC0 #2
TIM0_CC1 #2
TIM0_CC2 #2
U0_TX #0
U0_RX #0
PF7
PF8
ETM_TCLK #1
ETM_TD0 #1
PF9
EBI_REn #1
PD9
EBI_CS0 #0/1/2
EBI_CS1 #0/1/2
EBI_CS2 #0/1/2
EBI_CS3 #0/1/2
EBI_AD00 #0/1/2
EBI_AD01 #0/1/2
EBI_AD02 #0/1/2
PD10
PD11
PD12
PE8
PCNT2_S0IN #1
PCNT2_S1IN #1
TIM1_CC0 #1
PRS_CH3 #1
BOOT_TX
PE9
PE10
US0_TX #0
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
60
...the world's most energy friendly microcontrollers
LQFP100 Pin#
and Name
Pin Alternate Functionality / Description
Pin Name
Analog
EBI
Timers
Communication
Other
LES_ALTEX5 #0
BOOT_RX
95
PE11
PE12
EBI_AD03 #0/1/2
EBI_AD04 #0/1/2
TIM1_CC1 #1
TIM1_CC2 #1
US0_RX #0
US0_RX #3
US0_CLK #0
I2C0_SDA #6
CMU_CLK1 #2
LES_ALTEX6 #0
96
97
US0_TX #3
US0_CS #0
I2C0_SCL #6
LES_ALTEX7 #0
ACMP0_O #0
GPIO_EM4WU5
PE13
EBI_AD05 #0/1/2
98
99
PE14
PE15
PA15
EBI_AD06 #0/1/2
EBI_AD07 #0/1/2
EBI_AD08 #0/1/2
TIM3_CC0 #0
TIM3_CC1 #0
TIM3_CC2 #0
LEU0_TX #2
LEU0_RX #2
100
4.2 Alternate Functionality Pinout
A wide selection of alternate functionality is available for multiplexing to various pins. This is shown in
Table 4.2 (p. 61). The table shows the name of the alternate functionality in the first column, followed
by columns showing the possible LOCATION bitfield settings.
Note
Some functionality, such as analog interfaces, do not have alternate settings or a LOCA-
TION bitfield. In these cases, the pinout is shown in the column corresponding to LOCA-
TION 0.
Table 4.2. Alternate functionality overview
Alternate
LOCATION
Functionality
ACMP0_CH0
ACMP0_CH1
ACMP0_CH2
ACMP0_CH3
ACMP0_CH4
ACMP0_CH5
ACMP0_CH6
ACMP0_CH7
ACMP0_O
0
1
2
3
4
5
6
Description
PC0
PC1
PC2
PC3
PC4
PC5
PC6
PC7
PE13
PC8
PC9
PC10
PC11
PF2
Analog comparator ACMP0, channel 0.
Analog comparator ACMP0, channel 1.
Analog comparator ACMP0, channel 2.
Analog comparator ACMP0, channel 3.
Analog comparator ACMP0, channel 4.
Analog comparator ACMP0, channel 5.
Analog comparator ACMP0, channel 6.
Analog comparator ACMP0, channel 7.
PE2
PD6
Analog comparator ACMP0, digital output.
Analog comparator ACMP1, channel 0.
ACMP1_CH0
ACMP1_CH1
ACMP1_CH2
ACMP1_CH3
ACMP1_O
Analog comparator ACMP1, channel 1.
Analog comparator ACMP1, channel 2.
Analog comparator ACMP1, channel 3.
PE3
PD7
Analog comparator ACMP1, digital output.
Analog to digital converter ADC0, input channel number 0.
Analog to digital converter ADC0, input channel number 1.
Analog to digital converter ADC0, input channel number 2.
Analog to digital converter ADC0, input channel number 3.
ADC0_CH0
PD0
PD1
PD2
PD3
ADC0_CH1
ADC0_CH2
ADC0_CH3
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
61
...the world's most energy friendly microcontrollers
Alternate
LOCATION
Functionality
ADC0_CH4
ADC0_CH5
ADC0_CH6
ADC0_CH7
BOOT_RX
0
1
2
3
4
5
6
Description
PD4
PD5
PD6
PD7
PE11
PE10
Analog to digital converter ADC0, input channel number 4.
Analog to digital converter ADC0, input channel number 5.
Analog to digital converter ADC0, input channel number 6.
Analog to digital converter ADC0, input channel number 7.
Bootloader RX
BOOT_TX
Bootloader TX
Backup Power Domain status, whether or not the system
is in backup mode
BU_STAT
PE3
BU_VIN
PD8
PE2
PA2
PA1
Battery input for Backup Power Domain
BU_VOUT
CMU_CLK0
CMU_CLK1
Power output for Backup Power Domain
Clock Management Unit, clock output number 0.
Clock Management Unit, clock output number 1.
PD7
PD8
PE12
DAC0_N0 /
OPAMP_N0
PC5
Operational Amplifier 0 external negative input.
DAC0_N1 /
OPAMP_N1
PD7
PD3
PB11
Operational Amplifier 1 external negative input.
Operational Amplifier 2 external negative input.
OPAMP_N2
DAC0_OUT0 /
OPAMP_OUT0
Digital to Analog Converter DAC0_OUT0 /
OPAMP output channel number 0.
DAC0_OUT0ALT /
OPAMP_OUT0ALT
Digital to Analog Converter DAC0_OUT0ALT /
OPAMP alternative output for channel 0.
PC0
PC1
PC2
PC3
PD0
DAC0_OUT1 /
OPAMP_OUT1
Digital to Analog Converter DAC0_OUT1 /
OPAMP output channel number 1.
PB12
DAC0_OUT1ALT /
OPAMP_OUT1ALT
Digital to Analog Converter DAC0_OUT1ALT /
OPAMP alternative output for channel 1.
PD1
OPAMP_OUT2
PD5
PC4
PD0
Operational Amplifier 2 output.
DAC0_P0 /
OPAMP_P0
Operational Amplifier 0 external positive input.
DAC0_P1 /
OPAMP_P1
PD6
PD4
Operational Amplifier 1 external positive input.
OPAMP_P2
Operational Amplifier 2 external positive input.
Debug-interface Serial Wire clock input.
DBG_SWCLK
PF0
PF1
PF2
PF0
PF1
PF0
PF1
PD1
PF0
PF1
PD2
Note that this function is enabled to pin out of reset, and
has a built-in pull down.
Debug-interface Serial Wire data input / output.
DBG_SWDIO
DBG_SWO
Note that this function is enabled to pin out of reset, and
has a built-in pull up.
Debug-interface Serial Wire viewer Output.
Note that this function is not enabled after reset, and must
be enabled by software to be used.
EBI_A00
EBI_A01
EBI_A02
EBI_A03
EBI_A04
EBI_A05
EBI_A06
EBI_A07
PA12
PA13
PA14
PB9
PA12
PA13
PA14
PB9
PA12
PA13
PA14
PB9
External Bus Interface (EBI) address output pin 00.
External Bus Interface (EBI) address output pin 01.
External Bus Interface (EBI) address output pin 02.
External Bus Interface (EBI) address output pin 03.
External Bus Interface (EBI) address output pin 04.
External Bus Interface (EBI) address output pin 05.
External Bus Interface (EBI) address output pin 06.
External Bus Interface (EBI) address output pin 07.
PB10
PC6
PB10
PC6
PB10
PC6
PC7
PC7
PC7
PE0
PE0
PE0
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
62
...the world's most energy friendly microcontrollers
Alternate
LOCATION
Functionality
EBI_A08
EBI_A09
EBI_A10
EBI_A11
EBI_A12
EBI_A13
EBI_A14
EBI_A15
EBI_A16
EBI_A17
EBI_A18
EBI_A19
EBI_A20
EBI_A21
EBI_A22
EBI_A23
EBI_A24
EBI_A25
EBI_A26
EBI_A27
0
1
2
PE1
PC9
PC10
PE4
PE5
PE6
PE7
PC8
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PC0
PC1
PC2
PC4
PD2
3
4
5
6
Description
PE1
PE2
PE3
PE4
PE5
PE6
PE7
PC8
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PC0
PC1
PC2
PC4
PD2
PE1
External Bus Interface (EBI) address output pin 08.
External Bus Interface (EBI) address output pin 09.
External Bus Interface (EBI) address output pin 10.
External Bus Interface (EBI) address output pin 11.
External Bus Interface (EBI) address output pin 12.
External Bus Interface (EBI) address output pin 13.
External Bus Interface (EBI) address output pin 14.
External Bus Interface (EBI) address output pin 15.
External Bus Interface (EBI) address output pin 16.
External Bus Interface (EBI) address output pin 17.
External Bus Interface (EBI) address output pin 18.
External Bus Interface (EBI) address output pin 19.
External Bus Interface (EBI) address output pin 20.
External Bus Interface (EBI) address output pin 21.
External Bus Interface (EBI) address output pin 22.
External Bus Interface (EBI) address output pin 23.
External Bus Interface (EBI) address output pin 24.
External Bus Interface (EBI) address output pin 25.
External Bus Interface (EBI) address output pin 26.
External Bus Interface (EBI) address output pin 27.
PC9
PC10
PE4
PE5
PE6
PE7
PC8
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PC0
PC1
PC2
PC4
PD2
External Bus Interface (EBI) address and data input / out-
put pin 00.
EBI_AD00
EBI_AD01
EBI_AD02
EBI_AD03
EBI_AD04
EBI_AD05
EBI_AD06
EBI_AD07
EBI_AD08
EBI_AD09
EBI_AD10
EBI_AD11
EBI_AD12
EBI_AD13
PE8
PE8
PE8
External Bus Interface (EBI) address and data input / out-
put pin 01.
PE9
PE9
PE9
External Bus Interface (EBI) address and data input / out-
put pin 02.
PE10
PE11
PE12
PE13
PE14
PE15
PA15
PA0
PE10
PE11
PE12
PE13
PE14
PE15
PA15
PA0
PE10
PE11
PE12
PE13
PE14
PE15
PA15
PA0
External Bus Interface (EBI) address and data input / out-
put pin 03.
External Bus Interface (EBI) address and data input / out-
put pin 04.
External Bus Interface (EBI) address and data input / out-
put pin 05.
External Bus Interface (EBI) address and data input / out-
put pin 06.
External Bus Interface (EBI) address and data input / out-
put pin 07.
External Bus Interface (EBI) address and data input / out-
put pin 08.
External Bus Interface (EBI) address and data input / out-
put pin 09.
External Bus Interface (EBI) address and data input / out-
put pin 10.
PA1
PA1
PA1
External Bus Interface (EBI) address and data input / out-
put pin 11.
PA2
PA2
PA2
External Bus Interface (EBI) address and data input / out-
put pin 12.
PA3
PA3
PA3
External Bus Interface (EBI) address and data input / out-
put pin 13.
PA4
PA4
PA4
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
63
...the world's most energy friendly microcontrollers
Alternate
LOCATION
Functionality
0
1
2
3
4
5
6
Description
External Bus Interface (EBI) address and data input / out-
put pin 14.
EBI_AD14
PA5
PA6
PA5
PA5
External Bus Interface (EBI) address and data input / out-
put pin 15.
EBI_AD15
EBI_ALE
PA6
PC11
PF2
PA6
PC11
PF2
External Bus Interface (EBI) Address Latch Enable output.
External Bus Interface (EBI) Hardware Ready Control in-
put.
EBI_ARDY
PF2
EBI_BL0
PF6
PF6
PF6
External Bus Interface (EBI) Byte Lane/Enable pin 0.
External Bus Interface (EBI) Byte Lane/Enable pin 1.
External Bus Interface (EBI) Chip Select output 0.
External Bus Interface (EBI) Chip Select output 1.
External Bus Interface (EBI) Chip Select output 2.
External Bus Interface (EBI) Chip Select output 3.
External Bus Interface (EBI) Chip Select output TFT.
External Bus Interface (EBI) TFT Dot Clock pin.
External Bus Interface (EBI) TFT Data Enable pin.
EBI_BL1
PF7
PF7
PF7
EBI_CS0
EBI_CS1
EBI_CS2
EBI_CS3
EBI_CSTFT
EBI_DCLK
EBI_DTEN
PD9
PD10
PD11
PD12
PA7
PD9
PD10
PD11
PD12
PA7
PD9
PD10
PD11
PD12
PA7
PA8
PA8
PA8
PA9
PA9
PA9
External Bus Interface (EBI) TFT Horizontal Synchroniza-
tion pin.
EBI_HSNC
PA11
PA11
PA11
EBI_NANDREn
EBI_NANDWEn
EBI_REn
PC3
PC5
PF5
PC3
PC5
PF9
PC3
PC5
PF5
External Bus Interface (EBI) NAND Read Enable output.
External Bus Interface (EBI) NAND Write Enable output.
External Bus Interface (EBI) Read Enable output.
External Bus Interface (EBI) TFT Vertical Synchronization
pin.
EBI_VSNC
PA10
PA10
PA10
EBI_WEn
PF8
PF8
PF9
External Bus Interface (EBI) Write Enable output.
Embedded Trace Module ETM clock .
ETM_TCLK
PD7
PD6
PD3
PD4
PD5
PA0
PA6
PC9
PF1
PF2
PE13
PC6
PC7
PD3
PD4
PD5
PA6
PA2
PA3
PA4
PA5
ETM_TD0
Embedded Trace Module ETM data 0.
ETM_TD1
Embedded Trace Module ETM data 1.
ETM_TD2
Embedded Trace Module ETM data 2.
ETM_TD3
Embedded Trace Module ETM data 3.
GPIO_EM4WU0
GPIO_EM4WU1
GPIO_EM4WU2
GPIO_EM4WU3
GPIO_EM4WU4
GPIO_EM4WU5
Pin can be used to wake the system up from EM4
Pin can be used to wake the system up from EM4
Pin can be used to wake the system up from EM4
Pin can be used to wake the system up from EM4
Pin can be used to wake the system up from EM4
Pin can be used to wake the system up from EM4
High Frequency Crystal negative pin. Also used as exter-
nal optional clock input pin.
HFXTAL_N
PB14
HFXTAL_P
I2C0_SCL
PB13
PA1
PA0
PC5
PC4
PD6
PD7
High Frequency Crystal positive pin.
I2C0 Serial Clock Line input / output.
I2C0 Serial Data input / output.
PD7
PC7
PC6
PE1
PE0
PC1
PC0
PF1
PF0
PE13
PE12
I2C0_SDA
I2C1_SCL
PD6
PB12
PB11
I2C1 Serial Clock Line input / output.
I2C1 Serial Data input / output.
I2C1_SDA
LES_ALTEX0
LES_ALTEX1
LESENSE alternate exite output 0.
LESENSE alternate exite output 1.
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
64
...the world's most energy friendly microcontrollers
Alternate
LOCATION
Functionality
LES_ALTEX2
LES_ALTEX3
LES_ALTEX4
LES_ALTEX5
LES_ALTEX6
LES_ALTEX7
LES_CH0
0
1
2
3
4
5
6
Description
LESENSE alternate exite output 2.
LESENSE alternate exite output 3.
LESENSE alternate exite output 4.
LESENSE alternate exite output 5.
LESENSE alternate exite output 6.
LESENSE alternate exite output 7.
LESENSE channel 0.
PA3
PA4
PA5
PE11
PE12
PE13
PC0
PC1
PC2
PC3
PC4
PC5
PC6
PC7
PC8
PC9
PC10
PC11
PD6
PD7
PD5
LES_CH1
LESENSE channel 1.
LES_CH2
LESENSE channel 2.
LES_CH3
LESENSE channel 3.
LES_CH4
LESENSE channel 4.
LES_CH5
LESENSE channel 5.
LES_CH6
LESENSE channel 6.
LES_CH7
LESENSE channel 7.
LES_CH8
LESENSE channel 8.
LES_CH9
LESENSE channel 9.
LES_CH10
LES_CH11
LETIM0_OUT0
LETIM0_OUT1
LEU0_RX
LESENSE channel 10.
LESENSE channel 11.
PB11
PB12
PB14
PF0
PC4
PC5
PF1
Low Energy Timer LETIM0, output channel 0.
Low Energy Timer LETIM0, output channel 1.
LEUART0 Receive input.
PF1
PE15
PA0
LEUART0 Transmit output. Also used as receive input in
half duplex communication.
LEU0_TX
LEU1_RX
LEU1_TX
PD4
PC7
PC6
PB13
PA6
PA5
PE14
PF0
PF2
LEUART1 Receive input.
LEUART1 Transmit output. Also used as receive input in
half duplex communication.
Low Frequency Crystal (typically 32.768 kHz) negative
pin. Also used as an optional external clock input pin.
LFXTAL_N
PB8
PB7
LFXTAL_P
PCNT0_S0IN
PCNT0_S1IN
PCNT1_S0IN
PCNT1_S1IN
PCNT2_S0IN
PCNT2_S1IN
PRS_CH0
Low Frequency Crystal (typically 32.768 kHz) positive pin.
Pulse Counter PCNT0 input number 0.
PE0
PE1
PB3
PB4
PE8
PE9
PC0
PC1
PD6
PD7
Pulse Counter PCNT0 input number 1.
PC4
PC5
PD0
PD1
PA0
PA1
PC0
PC1
PA0
PA1
PA2
PA3
Pulse Counter PCNT1 input number 0.
Pulse Counter PCNT1 input number 1.
Pulse Counter PCNT2 input number 0.
Pulse Counter PCNT2 input number 1.
Peripheral Reflex System PRS, channel 0.
Peripheral Reflex System PRS, channel 1.
Peripheral Reflex System PRS, channel 2.
Peripheral Reflex System PRS, channel 3.
Timer 0 Capture Compare input / output channel 0.
Timer 0 Capture Compare input / output channel 1.
Timer 0 Capture Compare input / output channel 2.
Timer 0 Complimentary Deat Time Insertion channel 0.
PRS_CH1
PRS_CH2
PF5
PE8
PA0
PA1
PA2
PRS_CH3
TIM0_CC0
PF6
PF7
PF8
PD1
PD2
PD3
PA0
PC0
PC1
PC2
PF0
PF1
PF2
TIM0_CC1
TIM0_CC2
TIM0_CDTI0
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
65
...the world's most energy friendly microcontrollers
Alternate
LOCATION
Functionality
TIM0_CDTI1
TIM0_CDTI2
TIM1_CC0
TIM1_CC1
TIM1_CC2
TIM2_CC0
TIM2_CC1
TIM2_CC2
TIM3_CC0
TIM3_CC1
TIM3_CC2
U0_RX
0
1
2
3
4
5
6
Description
PA4
PA5
PC3
Timer 0 Complimentary Deat Time Insertion channel 1.
Timer 0 Complimentary Deat Time Insertion channel 2.
Timer 1 Capture Compare input / output channel 0.
Timer 1 Capture Compare input / output channel 1.
Timer 1 Capture Compare input / output channel 2.
Timer 2 Capture Compare input / output channel 0.
Timer 2 Capture Compare input / output channel 1.
Timer 2 Capture Compare input / output channel 2.
Timer 3 Capture Compare input / output channel 0.
Timer 3 Capture Compare input / output channel 1.
Timer 3 Capture Compare input / output channel 2.
UART0 Receive input.
PF5
PB0
PB1
PB2
PC8
PC9
PC10
PC4
PD6
PD7
PF5
PE10
PE11
PE12
PA12
PA13
PA14
PE0
PB7
PB8
PB11
PA8
PA9
PA10
PE14
PE15
PA15
PF7
PE1
PE2
PE1
PA4
PA3
PB10
PB9
UART0 Transmit output. Also used as receive input in half
duplex communication.
U0_TX
U1_RX
U1_TX
PF6
PE0
PF11
PF10
PE3
PE2
UART1 Receive input.
UART1 Transmit output. Also used as receive input in half
duplex communication.
US0_CLK
US0_CS
PE12
PE13
PE5
PE4
PC9
PC8
PB13
PB14
PB13
PB14
USART0 clock input / output.
USART0 chip select input / output.
USART0 Asynchronous Receive.
US0_RX
US0_TX
PE11
PE10
PE6
PE7
PC10
PC11
PE12
PE13
PB8
PB7
PC1
PC0
USART0 Synchronous mode Master Input / Slave Output
(MISO).
USART0 Asynchronous Transmit.Also used as receive in-
put in half duplex communication.
USART0 Synchronous mode Master Output / Slave Input
(MOSI).
US1_CLK
US1_CS
PB7
PB8
PD2
PD3
PF0
PF1
USART1 clock input / output.
USART1 chip select input / output.
USART1 Asynchronous Receive.
US1_RX
US1_TX
PC1
PC0
PD1
PD0
PD6
PD7
USART1 Synchronous mode Master Input / Slave Output
(MISO).
USART1 Asynchronous Transmit.Also used as receive in-
put in half duplex communication.
USART1 Synchronous mode Master Output / Slave Input
(MOSI).
US2_CLK
US2_CS
PC4
PC5
PB5
PB6
USART2 clock input / output.
USART2 chip select input / output.
USART2 Asynchronous Receive.
US2_RX
US2_TX
PC3
PC2
PB4
PB3
USART2 Synchronous mode Master Input / Slave Output
(MISO).
USART2 Asynchronous Transmit.Also used as receive in-
put in half duplex communication.
USART2 Synchronous mode Master Output / Slave Input
(MOSI).
USB_DM
USB_DMPU
USB_DP
PF10
PD2
USB D- pin.
USB D- Pullup control.
USB D+ pin.
PF11
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
66
...the world's most energy friendly microcontrollers
Alternate
LOCATION
Functionality
USB_ID
0
1
2
3
4
5
6
Description
PF12
USB ID pin. Used in OTG mode.
USB_VBUS
USB_VBUS
PF5
USB 5 V VBUS input.
USB_VBUSEN
USB_VREGI
USB 5 V VBUS enable.
USB_VREGI
USB Input to internal 3.3 V regulator
USB Decoupling for internal 3.3 V USB regulator and reg-
ulator output
USB_VREGO
USB_VREGO
4.3 GPIO Pinout Overview
The specific GPIO pins available in EFM32WG380 is shown in Table 4.3 (p. 67). Each GPIO port is
organized as 16-bit ports indicated by letters A through F, and the individual pin on this port in indicated
by a number from 15 down to 0.
Table 4.3. GPIO Pinout
Port
Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin
Pin
0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
Port A
Port B
Port C
Port D
Port E
Port F
PA15 PA14 PA13 PA12 PA11 PA10
PA9
PB9
PC9
PD9
PE9
PF9
PA8
PB8
PC8
PD8
PE8
PF8
PA7
PB7
PC7
PD7
PE7
PF7
PA6
PB6
PC6
PD6
PE6
PF6
PA5
PB5
PC5
PD5
PE5
PF5
PA4
PB4
PC4
PD4
PE4
-
PA3
PB3
PC3
PD3
PE3
-
PA2
PB2
PC2
PD2
PE2
PF2
PA1
PB1
PC1
PD1
PE1
PF1
PA0
PB0
PC0
PD0
PE0
PF0
-
-
-
PB14 PB13 PB12 PB11 PB10
-
-
-
-
-
PC11 PC10
PD12 PD11 PD10
PE15 PE14 PE13 PE12 PE11 PE10
PF12 PF11 PF10
-
-
-
4.4 Opamp Pinout Overview
The specific opamp terminals available in EFM32WG380 is shown in Figure 4.2 (p. 67) .
Figure 4.2. Opamp Pinout
PB11
PB12
PC0
OUT0ALT
OUT0
PC4
PC5
+
OPA0
-
PC1
PC2
PC3
+
PD4
PD3
PC12
PC13
PC14
PC15
PD0
OPA2
-
OUT2
PD6
PD7
OUT1ALT
OUT1
+
OPA1
-
PD1
PD5
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
67
...the world's most energy friendly microcontrollers
4.5 LQFP100 Package
Figure 4.3. LQFP100
Note:
1. Datum 'T', 'U' and 'Z' to be determined at datum plane 'H'.
2. Datum 'D' and 'E' to be determined at seating plane datum 'Y'.
3. Dimension 'D1' and 'E1' do not include mold protrusions. Allowable protrusion is 0.25 per side. Di-
mensions 'D1' and 'E1' do include mold mismatch and are determined at datum plane datum 'H'.
4. Dimension 'b' does not include dambar protrusion. Allowable dambar protrusion shall not cause the
lead width to exceed the maximum 'b' dimension by more than 0.08 mm. Dambar can not be located
on the lower radius or the foot. Minimum space between protrusion and an adjacent lead is 0.07 mm
5. Exact shape of each corner is optional.
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
68
...the world's most energy friendly microcontrollers
Table 4.4. LQFP100 (Dimensions in mm)
SYMBOL
MIN
--
NOM
--
MAX
1.6
total thickness
stand off
A
A1
A2
b
0.05
1.35
0.17
0.17
0.09
0.09
--
0.15
1.45
0.27
0.23
0.2
mold thickness
lead width (plating)
lead width
1.4
0.2
b1
c
--
L/F thickness (plating)
lead thickness
x
--
c1
D
--
0.16
16 BSC
16 BSC
14 BSC
14 BSC
0.5 BSC
0.6
y
E
x
D1
E1
e
body size
y
lead pitch
footprint
L
0.45
0.75
L1
1 REF
3.5°
0°
0°
7°
--
θ
--
θ1
θ2
11°
11°
12°
12°
13°
13°
θ3
R1
0.08
0.08
0.2
--
--
0.2
--
R1
--
S
--
package edge tolerance
lead edge tolerance
coplanarity
aaa
bbb
ccc
ddd
eee
0.2
0.2
0.08
0.08
0.05
lead offset
mold flatness
The LQFP100 Package uses Nickel-Palladium-Gold preplated leadframe.
All EFM32 packages are RoHS compliant and free of Bromine (Br) and Antimony (Sb).
For additional Quality and Environmental information, please see:
http://www.silabs.com/support/quality/pages/default.aspx
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
69
...the world's most energy friendly microcontrollers
5 PCB Layout and Soldering
5.1 Recommended PCB Layout
Figure 5.1. LQFP100 PCB Land Pattern
a
p8
p7
p6
p1
b
e
c
p2
p5
p3
p4
d
Table 5.1. QFP100 PCB Land Pattern Dimensions (Dimensions in mm)
Symbol
Dim. (mm)
1.45
Symbol
P1
Pin number
Symbol
Pin number
a
b
c
d
e
1
P6
P7
P8
-
75
76
100
-
0.30
P2
25
26
50
51
0.50
P3
15.40
15.40
P4
P5
-
-
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
70
...the world's most energy friendly microcontrollers
Figure 5.2. LQFP100 PCB Solder Mask
a
b
c
e
d
Table 5.2. QFP100 PCB Solder Mask Dimensions (Dimensions in mm)
Symbol
Dim. (mm)
a
b
c
d
e
1.57
0.42
0.50
15.40
15.40
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
71
...the world's most energy friendly microcontrollers
Figure 5.3. LQFP100 PCB Stencil Design
a
b
c
e
d
Table 5.3. QFP100 PCB Stencil Design Dimensions (Dimensions in mm)
Symbol
Dim. (mm)
a
b
c
d
e
1.35
0.20
0.50
15.40
15.40
1. The drawings are not to scale.
2. All dimensions are in millimeters.
3. All drawings are subject to change without notice.
4. The PCB Land Pattern drawing is in compliance with IPC-7351B.
5. Stencil thickness 0.125 mm.
6. For detailed pin-positioning, see Figure 4.3 (p. 68) .
5.2 Soldering Information
The latest IPC/JEDEC J-STD-020 recommendations for Pb-Free reflow soldering should be followed.
The packages have a Moisture Sensitivity Level rating of 3, please see the latest IPC/JEDEC J-STD-033
standard for MSL description and level 3 bake conditions.
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
72
...the world's most energy friendly microcontrollers
6 Chip Marking, Revision and Errata
6.1 Chip Marking
In the illustration below package fields and position are shown.
Figure 6.1. Example Chip Marking (top view)
6.2 Revision
The revision of a chip can be determined from the "Revision" field in Figure 6.1 (p. 73) .
6.3 Errata
Please see the errata document for EFM32WG380 for description and resolution of device erratas. This
document is available in Simplicity Studio and online at:
http://www.silabs.com/support/pages/document-library.aspx?p=MCUs--32-bit
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
73
...the world's most energy friendly microcontrollers
7 Revision History
7.1 Revision 1.40
June 13th, 2014
Removed "Preliminary" markings.
Corrected single power supply voltage minimum value from 1.85V to 1.98V.
Added AUXHFRCO to blockdiagram and electrical characteristics.
Updated current consumption data.
Updated transition between energy modes data.
Updated power management data.
Updated GPIO data.
Updated LFRCO, HFRCO and ULFRCO data.
Updated ADC data.
Updated DAC data.
Updated OPAMP data.
Updated ACMP data.
Updated VCMP data.
Added EBI timing chapter.
7.2 Revision 1.31
November 21st, 2013
Updated figures.
Updated errata-link.
Updated chip marking.
Added link to Environmental and Quality information.
Re-added missing DAC-data.
7.3 Revision 1.30
September 30th, 2013
Added I2C characterization data.
Added SPI characterization data.
Corrected the DAC and OPAMP2 pin sharing information in the Alternate Functionality Pinout section.
Added the USB bootloader information.
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
74
...the world's most energy friendly microcontrollers
Corrected the ADC resolution from 12, 10 and 6 bit to 12, 8 and 6 bit.
Updated the EM0 and EM1 current consumption numbers. Updated the the EM1 plots and removed
the EM0 plots.
Updated Environmental information.
Updated trademark, disclaimer and contact information.
Other minor corrections.
7.4 Revision 1.20
June 28th, 2013
Updated power requirements in the Power Management section.
Removed minimum load capacitance figure and table. Added reference to application note.
Other minor corrections.
7.5 Revision 1.10
May 6th, 2013
Updated current consumption table and figures in Electrical characteristics section.
Other minor corrections.
7.6 Revision 1.00
September 11th, 2012
Updated the HFRCO 1 MHz band typical value to 1.2 MHz.
Updated the HFRCO 7 MHz band typical value to 6.6 MHz.
Other minor corrections.
7.7 Revision 0.95
May 3rd, 2012
Updated EM2/EM3 current consumption at 85°C.
7.8 Revision 0.90
February 27th, 2012
Initial preliminary release.
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
75
...the world's most energy friendly microcontrollers
A Disclaimer and Trademarks
A.1 Disclaimer
Silicon Laboratories intends to provide customers with the latest, accurate, and in-depth documentation
of all peripherals and modules available for system and software implementers using or intending to use
the Silicon Laboratories products. Characterization data, available modules and peripherals, memory
sizes and memory addresses refer to each specific device, and "Typical" parameters provided can and
do vary in different applications. Application examples described herein are for illustrative purposes only.
Silicon Laboratories reserves the right to make changes without further notice and limitation to product
information, specifications, and descriptions herein, and does not give warranties as to the accuracy
or completeness of the included information. Silicon Laboratories shall have no liability for the conse-
quences of use of the information supplied herein. This document does not imply or express copyright
licenses granted hereunder to design or fabricate any integrated circuits. The products must not be
used within any Life Support System without the specific written consent of Silicon Laboratories. A "Life
Support System" is any product or system intended to support or sustain life and/or health, which, if it
fails, can be reasonably expected to result in significant personal injury or death. Silicon Laboratories
products are generally not intended for military applications. Silicon Laboratories products shall under no
circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological
or chemical weapons, or missiles capable of delivering such weapons.
A.2 Trademark Information
Silicon Laboratories Inc., Silicon Laboratories, Silicon Labs, SiLabs and the Silicon Labs logo, CMEMS®,
EFM, EFM32, EFR, Energy Micro, Energy Micro logo and combinations thereof, "the world’s most ener-
gy friendly microcontrollers", Ember®, EZLink®, EZMac®, EZRadio®, EZRadioPRO®, DSPLL®, ISO-
modem®, Precision32®, ProSLIC®, SiPHY®, USBXpress® and others are trademarks or registered
trademarks of Silicon Laboratories Inc. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or reg-
istered trademarks of ARM Holdings. Keil is a registered trademark of ARM Limited. All other products
or brand names mentioned herein are trademarks of their respective holders.
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
76
...the world's most energy friendly microcontrollers
B Contact Information
Silicon Laboratories Inc.
400 West Cesar Chavez
Austin, TX 78701
Please visit the Silicon Labs Technical Support web page:
http://www.silabs.com/support/pages/contacttechnicalsupport.aspx
and register to submit a technical support request.
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
77
...the world's most energy friendly microcontrollers
Table of Contents
1. Ordering Information .................................................................................................................................. 2
2. System Summary ...................................................................................................................................... 3
2.1. System Introduction ......................................................................................................................... 3
2.2. Configuration Summary .................................................................................................................... 7
2.3. Memory Map ................................................................................................................................. 9
3. Electrical Characteristics ........................................................................................................................... 10
3.1. Test Conditions ............................................................................................................................. 10
3.2. Absolute Maximum Ratings ............................................................................................................. 10
3.3. General Operating Conditions .......................................................................................................... 10
3.4. Current Consumption ..................................................................................................................... 11
3.5. Transition between Energy Modes .................................................................................................... 17
3.6. Power Management ....................................................................................................................... 18
3.7. Flash .......................................................................................................................................... 19
3.8. General Purpose Input Output ......................................................................................................... 19
3.9. Oscillators .................................................................................................................................... 27
3.10. Analog Digital Converter (ADC) ...................................................................................................... 32
3.11. Digital Analog Converter (DAC) ...................................................................................................... 42
3.12. Operational Amplifier (OPAMP) ...................................................................................................... 43
3.13. Analog Comparator (ACMP) .......................................................................................................... 47
3.14. Voltage Comparator (VCMP) ......................................................................................................... 49
3.15. EBI ........................................................................................................................................... 49
3.16. I2C ........................................................................................................................................... 53
3.17. USART SPI ................................................................................................................................ 54
3.18. Digital Peripherals ....................................................................................................................... 56
4. Pinout and Package ................................................................................................................................. 57
4.1. Pinout ......................................................................................................................................... 57
4.2. Alternate Functionality Pinout .......................................................................................................... 61
4.3. GPIO Pinout Overview ................................................................................................................... 67
4.4. Opamp Pinout Overview ................................................................................................................. 67
4.5. LQFP100 Package ........................................................................................................................ 68
5. PCB Layout and Soldering ........................................................................................................................ 70
5.1. Recommended PCB Layout ............................................................................................................ 70
5.2. Soldering Information ..................................................................................................................... 72
6. Chip Marking, Revision and Errata .............................................................................................................. 73
6.1. Chip Marking ................................................................................................................................ 73
6.2. Revision ...................................................................................................................................... 73
6.3. Errata ......................................................................................................................................... 73
7. Revision History ...................................................................................................................................... 74
7.1. Revision 1.40 ............................................................................................................................... 74
7.2. Revision 1.31 ............................................................................................................................... 74
7.3. Revision 1.30 ............................................................................................................................... 74
7.4. Revision 1.20 ............................................................................................................................... 75
7.5. Revision 1.10 ............................................................................................................................... 75
7.6. Revision 1.00 ............................................................................................................................... 75
7.7. Revision 0.95 ............................................................................................................................... 75
7.8. Revision 0.90 ............................................................................................................................... 75
A. Disclaimer and Trademarks ....................................................................................................................... 76
A.1. Disclaimer ................................................................................................................................... 76
A.2. Trademark Information ................................................................................................................... 76
B. Contact Information ................................................................................................................................. 77
B.1. ................................................................................................................................................. 77
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
78
...the world's most energy friendly microcontrollers
List of Figures
2.1. Block Diagram ....................................................................................................................................... 3
2.2. EFM32WG380 Memory Map with largest RAM and Flash sizes ....................................................................... 9
3.1. EM1 Current consumption with all peripheral clocks disabled and HFXO running at 48MHz ................................. 13
3.2. EM1 Current consumption with all peripheral clocks disabled and HFRCO running at 28MHz ............................... 13
3.3. EM1 Current consumption with all peripheral clocks disabled and HFRCO running at 21MHz ............................... 14
3.4. EM1 Current consumption with all peripheral clocks disabled and HFRCO running at 14MHz ............................... 14
3.5. EM1 Current consumption with all peripheral clocks disabled and HFRCO running at 11MHz ............................... 15
3.6. EM1 Current consumption with all peripheral clocks disabled and HFRCO running at 6.6MHz .............................. 15
3.7. EM1 Current consumption with all peripheral clocks disabled and HFRCO running at 1.2MHz .............................. 16
3.8. EM2 current consumption. RTC prescaled to 1kHz, 32.768 kHz LFRCO. ......................................................... 16
3.9. EM3 current consumption. ..................................................................................................................... 17
3.10. EM4 current consumption. ................................................................................................................... 17
3.11. Typical Low-Level Output Current, 2V Supply Voltage ................................................................................ 21
3.12. Typical High-Level Output Current, 2V Supply Voltage ................................................................................ 22
3.13. Typical Low-Level Output Current, 3V Supply Voltage ................................................................................ 23
3.14. Typical High-Level Output Current, 3V Supply Voltage ................................................................................ 24
3.15. Typical Low-Level Output Current, 3.8V Supply Voltage .............................................................................. 25
3.16. Typical High-Level Output Current, 3.8V Supply Voltage ............................................................................. 26
3.17. Calibrated LFRCO Frequency vs Temperature and Supply Voltage .............................................................. 28
3.18. Calibrated HFRCO 1 MHz Band Frequency vs Supply Voltage and Temperature ............................................ 29
3.19. Calibrated HFRCO 7 MHz Band Frequency vs Supply Voltage and Temperature ............................................ 30
3.20. Calibrated HFRCO 11 MHz Band Frequency vs Supply Voltage and Temperature ........................................... 30
3.21. Calibrated HFRCO 14 MHz Band Frequency vs Supply Voltage and Temperature ........................................... 30
3.22. Calibrated HFRCO 21 MHz Band Frequency vs Supply Voltage and Temperature ........................................... 31
3.23. Calibrated HFRCO 28 MHz Band Frequency vs Supply Voltage and Temperature ........................................... 31
3.24. Integral Non-Linearity (INL) ................................................................................................................... 37
3.25. Differential Non-Linearity (DNL) .............................................................................................................. 37
3.26. ADC Frequency Spectrum, Vdd = 3V, Temp = 25°C ................................................................................. 38
3.27. ADC Integral Linearity Error vs Code, Vdd = 3V, Temp = 25°C ................................................................... 39
3.28. ADC Differential Linearity Error vs Code, Vdd = 3V, Temp = 25°C ............................................................... 40
3.29. ADC Absolute Offset, Common Mode = Vdd /2 ........................................................................................ 41
3.30. ADC Dynamic Performance vs Temperature for all ADC References, Vdd = 3V .............................................. 41
3.31. ADC Temperature sensor readout ......................................................................................................... 42
3.32. OPAMP Common Mode Rejection Ratio ................................................................................................. 45
3.33. OPAMP Positive Power Supply Rejection Ratio ........................................................................................ 45
3.34. OPAMP Negative Power Supply Rejection Ratio ...................................................................................... 46
3.35. OPAMP Voltage Noise Spectral Density (Unity Gain) Vout=1V ..................................................................... 46
3.36. OPAMP Voltage Noise Spectral Density (Non-Unity Gain) .......................................................................... 46
3.37. ACMP Characteristics, Vdd = 3V, Temp = 25°C, FULLBIAS = 0, HALFBIAS = 1 ............................................. 48
3.38. EBI Write Enable Timing ....................................................................................................................... 49
3.39. EBI Address Latch Enable Related Output Timing ..................................................................................... 50
3.40. EBI Read Enable Related Output Timing ................................................................................................. 51
3.41. EBI Read Enable Related Timing Requirements ........................................................................................ 52
3.42. EBI Ready/Wait Related Timing Requirements .......................................................................................... 52
3.43. SPI Master Timing ............................................................................................................................... 54
3.44. SPI Slave Timing ................................................................................................................................ 55
4.1. EFM32WG380 Pinout (top view, not to scale) ............................................................................................. 57
4.2. Opamp Pinout ...................................................................................................................................... 67
4.3. LQFP100 ............................................................................................................................................. 68
5.1. LQFP100 PCB Land Pattern ................................................................................................................... 70
5.2. LQFP100 PCB Solder Mask .................................................................................................................... 71
5.3. LQFP100 PCB Stencil Design ................................................................................................................. 72
6.1. Example Chip Marking (top view) ............................................................................................................. 73
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
79
...the world's most energy friendly microcontrollers
List of Tables
1.1. Ordering Information ................................................................................................................................ 2
2.1. Configuration Summary ............................................................................................................................ 8
3.1. Absolute Maximum Ratings ..................................................................................................................... 10
3.2. General Operating Conditions .................................................................................................................. 10
3.3. Environmental ....................................................................................................................................... 11
3.4. Current Consumption ............................................................................................................................. 11
3.5. Energy Modes Transitions ...................................................................................................................... 17
3.6. Power Management ............................................................................................................................... 18
3.7. Flash .................................................................................................................................................. 19
3.8. GPIO .................................................................................................................................................. 19
3.9. LFXO .................................................................................................................................................. 27
3.10. HFXO ................................................................................................................................................ 27
3.11. LFRCO .............................................................................................................................................. 28
3.12. HFRCO ............................................................................................................................................. 29
3.13. AUXHFRCO ....................................................................................................................................... 32
3.14. ULFRCO ............................................................................................................................................ 32
3.15. ADC .................................................................................................................................................. 32
3.16. DAC .................................................................................................................................................. 42
3.17. OPAMP ............................................................................................................................................. 43
3.18. ACMP ............................................................................................................................................... 47
3.19. VCMP ............................................................................................................................................... 49
3.20. EBI Write Enable Timing ....................................................................................................................... 50
3.21. EBI Address Latch Enable Related Output Timing ..................................................................................... 50
3.22. EBI Read Enable Related Output Timing ................................................................................................. 51
3.23. EBI Read Enable Related Timing Requirements ........................................................................................ 52
3.24. EBI Ready/Wait Related Timing Requirements .......................................................................................... 52
3.25. I2C Standard-mode (Sm) ...................................................................................................................... 53
3.26. I2C Fast-mode (Fm) ............................................................................................................................ 53
3.27. I2C Fast-mode Plus (Fm+) .................................................................................................................... 54
3.28. SPI Master Timing ............................................................................................................................... 54
3.29. SPI Master Timing with SSSEARLY and SMSDELAY ................................................................................. 55
3.30. SPI Slave Timing ................................................................................................................................ 55
3.31. SPI Slave Timing with SSSEARLY and SMSDELAY .................................................................................. 55
3.32. Digital Peripherals ............................................................................................................................... 56
4.1. Device Pinout ....................................................................................................................................... 57
4.2. Alternate functionality overview ................................................................................................................ 61
4.3. GPIO Pinout ........................................................................................................................................ 67
4.4. LQFP100 (Dimensions in mm) ................................................................................................................. 69
5.1. QFP100 PCB Land Pattern Dimensions (Dimensions in mm) ......................................................................... 70
5.2. QFP100 PCB Solder Mask Dimensions (Dimensions in mm) ......................................................................... 71
5.3. QFP100 PCB Stencil Design Dimensions (Dimensions in mm) ....................................................................... 72
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
80
...the world's most energy friendly microcontrollers
List of Equations
3.1. Total ACMP Active Current ..................................................................................................................... 47
3.2. VCMP Trigger Level as a Function of Level Setting ..................................................................................... 49
www.silabs.com
2014-06-13 - EFM32WG380FXX - d0192_Rev1.40
81
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明