SI7007-A20-IM1R [SILICON]
Analog Voltage Output Sensor, 0.4V Min, 2.6V Max, 1Cel, Square, Surface Mount, DFN-6;
| 型号： | SI7007-A20-IM1R |
| 厂家： | 
SILICON |
| 描述： | Analog Voltage Output Sensor, 0.4V Min, 2.6V Max, 1Cel, Square, Surface Mount, DFN-6 输出元件 传感器 换能器 |
| 文件： | 总25页 (文件大小：1277K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Si7007-A20
HUMIDITY/TEMPERATURE SENSOR WITH PWM OUTPUT
Features
Precision Relative Humidity Sensor
±5% RH (max), 0–90% RH
Factory-calibrated
PWM Output
High Accuracy Temperature Sensor 3x3 mm DFN Package
±1 °C (max), –10 to 85 °C
0 to 100% RH operating range
–40 to +125 °C operating range
Wide operating voltage
(1.9 to 3.6 V)
Excellent long term stability
Optional factory-installed cover
Low-profile
Protection during reflow
Excludes liquids and particulates
Low Power Consumption
Applications
Ordering Information:
HVAC/R
Micro-environments/data centers
Automotive climate control and
defogging
Asset and goods tracking
Mobile phones and tablets
See page 18.
Thermostats/humidistats
Respiratory therapy
White goods
Pin Assignments
Top View
Indoor weather stations
Description
The Si7007 Humidity and Temperature Sensor is a monolithic CMOS IC
integrating humidity and temperature sensor elements, an analog-to-digital
converter, signal processing, calibration data, and a PWM output. The PWM
output may be filtered to produce an analog voltage output. The patented use of
industry-standard, low-K polymeric dielectrics for sensing humidity enables the
construction of low-power, monolithic CMOS Sensor ICs with low drift and
hysteresis, and excellent long term stability.
1
2
3
6
5
4
PWM1
GND
SELECT
VDD
DNC
PWM2
The humidity and temperature sensors are factory-calibrated and the calibration
data is stored in the on-chip non-volatile memory. This ensures that the sensors
are fully interchangeable, with no recalibration or software changes required.
Patent Protected. Patents pending
The Si7007 is available in a 3x3 mm DFN package and is reflow solderable. It can
be used as a hardware- and software-compatible drop-in upgrade for existing RH/
temperature sensors in 3x3 mm DFN-6 packages, featuring precision sensing
over a wider range and lower power consumption. The optional factory-installed
cover offers a low profile, convenient means of protecting the sensor during
assembly (e.g., reflow soldering) and throughout the life of the product, excluding
liquids (hydrophobic/oleophobic) and particulates.
The Si7007 offers an accurate, low-power, factory-calibrated digital solution ideal
for measuring humidity, dew-point, and temperature, in applications ranging from
HVAC/R and asset tracking to industrial and consumer platforms.
Rev. 1.4 8/16
Copyright © 2016 by Silicon Laboratories
Si7007-A20
Si7007-A20
Functional Block Diagram
VDD
Si7007
1.25V
Ref
Calibration
Memory
Humidity
Sensor
Control Logic
ADC
SELECT
Temp
Sensor
PWM1
PWM2
PWM Interface
GND
2
Rev. 1.4
Si7007-A20
TABLE OF CONTENTS
Section
Page
1. Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
2. Typical Application Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
3. Bill of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
4. Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
4.1. Relative Humidity Sensor Accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
4.2. Hysteresis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
4.3. Prolonged Exposure to High Humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
4.4. PCB Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
4.5. Protecting the Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
4.6. Bake/Hydrate Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
4.7. Long Term Drift/Aging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
5. PWM Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
6. Pin Descriptions: Si7007 (Top View) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
7. Ordering Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
8. Package Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
8.1. Package Outline: 3x3 6-pin DFN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
8.2. Package Outline: 3x3 6-pin DFN with Protective Cover . . . . . . . . . . . . . . . . . . . . . .20
9. PCB Land Pattern and Solder Mask Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
10. Top Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
10.1. Si7007 Top Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
10.2. Top Marking Explanation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
11. Additional Reference Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Document Change List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Rev. 1.4
3
Si7007-A20
1. Electrical Specifications
Unless otherwise specified, all min/max specifications apply over the recommended operating conditions.
Table 1. Recommended Operating Conditions
Symbol
VDD
Test Condition
Min
1.9
Typ
—
Max
3.6
Unit
V
Parameter
Power Supply
Operating Temperature
TA
–40
—
+125
°C
Table 2. General Specifications
1.9 < VDD < 3.6 V; TA = –40 to 125 °C unless otherwise noted.
Parameter
Symbol
Test Condition
SELECT pin
SELECT pin
Min
Typ
—
Max
Unit
Input Voltage High
Input Voltage Low
Input Voltage Range
Input Leakage
V
0.7xVDD
—
—
V
V
IH
VIL
VIN
IIL
—
0.3xVDD
SELECT pin with respect to GND
SELECT pin
0.0
—
VDD
1
V
—
—
μA
V
Output Voltage High
PWM1, PWM2 pins, IOH = –10 μA
V
V
– 0.1
– 0.2
—
—
DD
DD
PWM1, PWM2 pins pin,
—
—
—
—
—
V
V
V
VOH
VOL
IOH = –0.5 mA, V = 2.0 V
DD
PWM1, PWM2 pins,
V
– 0.4
DD
IOH = –1.7 mA, V = 3.0 V
DD
Output Voltage Low
Sample Rate
PWM1, PWM2 pins; IOL = 2.5 mA;
VDD = 3.3 V
—
0.6
PWM1, PWM2 pins; IOL = 1.2 mA;
VDD = 1.9 V
—
—
—
—
2
0.4
—
V
RH and Temperature
Average Current
Hz
μA
Current
Consumption
IDD
tPU
150
300
Powerup Time
From VDD ≥ 1.9 V to PWM output
—
—
48
—
55
enabled, 25 °C
ms
From VDD ≥ 1.9 V to PWM output
enabled, full temperature range
110
4
Rev. 1.4
Si7007-A20
Table 3. PWM Interface Specifications
1.9 VDD 3.6 V; TA = –40 to +125 °C unless otherwise noted.
Parameter
PWM Frequency
Symbol
FPWM
Test Condition
Min
Typ
Max
Unit
1.00
1.22
1.40
kHz
PWM Duty Cycle
DCPWM
t / t
0
—
1
H
PWM
SELECT Setup Time
From SELECT transition to
PWM valid
tSS
—
500
—
ms
tPWM
tH
tSS
RH Data
Temperature Data
Figure 1. PWM Interface Timing Diagram
Rev. 1.4
5
Si7007-A20
Table 4. Humidity Sensor
1.9 ≤ VDD ≤ 3.6 V; TA = 30 °C
Parameter
Symbol
Test Condition
Non-condensing
0 – 90% RH
Min
0
Typ
Max
100
±5
Unit
1
Operating Range
—
%RH
2, 3
Accuracy
—
±4
%RH
90 – 100% RH
See Figure 2.
Repeatability/Noise
Resolution
—
—
—
0.025
11
—
—
—
%RH RMS
Bits
S
4
Response Time
τ
1 m/s airflow, with or without
cover
6
63%
Drift vs. Temperature
Hysteresis
—
—
—
0.05
±1
—
—
—
%RH/°C
%RH
3
Long Term Stability
< 0.25
%RH/yr
Notes:
1. Recommended humidity operating range is 20% to 80% RH (non-condensing) over –10 °C to 60 °C. Prolonged
operation beyond these ranges may result in a shift of sensor reading, with slow recovery time.
2. Excludes hysteresis, long term drift, and certain other factors and is applicable to non-condensing environments only.
See Section “4.1. Relative Humidity Sensor Accuracy” for more details.
3. Drift due to aging effects at typical room conditions of 30 °C and 30% to 50% RH. May be impacted by dust, vaporized
solvents or other contaminants, e.g., out-gassing tapes, adhesives, packaging materials, etc. See Section “4.7. Long
Term Drift/Aging” .
4. Response time to a step change in RH. Time for the RH output to change by 63% of the total RH change.
Figure 2. RH Accuracy at 30 °C
6
Rev. 1.4
Si7007-A20
Table 5. Temperature Sensor
1.9 ≤ VDD ≤ 3.6 V; TA = –40 to +125 °C unless otherwise noted.
Parameter
Operating Range
Accuracy
Symbol
Test Condition
Min
–40
—
Typ
—
Max
+125
±1
Unit
°C
–10 °C< t < 85 °C
±0.5
Figure 3
0.04
11
°C
A
–40 < t < 125 °C
°C
A
Repeatability/Noise
Resolution
—
—
—
—
—
—
—
—
—
—
°C RMS
Bits
Response Time*
Unmounted device
Si7007-EB board
0.7
τ
s
63%
5.1
Long Term Stability
0.01
°C/Yr
*Note: Time to reach 63% of final value in response to a step change in temperature. Actual response time will vary
dependent on system thermal mass and air-flow.
Figure 3. Temperature Accuracy
Rev. 1.4
7
Si7007-A20
Table 6. Thermal Characteristics
Parameter
Symbol
Test Condition
DFN-6
Unit
Junction to Air Thermal Resistance
JEDEC 2-Layer board,
No Airflow
256
°C/W
JA
Junction to Air Thermal Resistance
Junction to Air Thermal Resistance
JEDEC 2-Layer board,
1 m/s Airflow
224
205
°C/W
°C/W
JA
JEDEC 2-Layer board,
2.5 m/s Airflow
JA
Junction to Case Thermal Resistance
Junction to Board Thermal Resistance
JEDEC 2-Layer board
JEDEC 2-Layer board
22
°C/W
°C/W
JC
134
JB
Table 7. Absolute Maximum Ratings1
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
Ambient temperature
under bias
–55
—
125
150
°C
2
Storage Temperature
Voltage on I/O pins
–65
—
—
°C
V
–0.3
V
+0.3 V
DD
Voltage on V with
respect to GND
DD
–0.3
—
4.2
V
ESD Tolerance
HBM
CDM
MM
—
—
—
—
—
—
2
kV
kV
V
1.25
250
Notes:
1. Absolute maximum ratings are stress ratings only, operation at or beyond these conditions is not implied and may
shorten the life of the device or alter its performance.
2. Special handling considerations apply; see application note, “AN607: Si70xx Humidity Sensor Designer’s Guide”.
8
Rev. 1.4
Si7007-A20
2. Typical Application Circuits
The primary function of the Si7007 is to measure relative humidity and temperature. Figure 4 demonstrates the
typical application circuit to achieve these functions.
1.9 to 3.6 V
C1
0.1 µF
5
U1
VDD
R1
Si7007
PWM1
100 k
1
4
VRH/VTEMP
C2
6
SELECT
0.1 µF
SELECT
PWM2
GND
VTEMP/VRH
R2
100 k
C3
0.1 µF
2
Figure 4. Typical Application Circuit for Relative Humidity and Temperature Measurement
Rev. 1.4
9
Si7007-A20
3. Bill of Materials
Table 8. Typical Application Circuit BOM for Relative Humidity and Temperature Measurement
Reference
Description
Mfr Part Number Manufacturer
C1
R1
C2
R2
C3
U1
Capacitor, 0.1 μA, 16 V, X7R, 0603
Resistor, 100 k, ±5%, 1/16 W, 0603
Capacitor, 1 μA, 16 V, X7R, 0603
Various
Various
Various
Various
Various
Various
Resistor, 100 k, ±5%, 1/16 W, 0603 (optional)
Capacitor, 1 μF, 16 V, X7R, 0603 (optional)
IC, Digital Temp/Humidity Sensor
Various
Various
Various
Various
Si7007-A20
Silicon Labs
10
Rev. 1.4
Si7007-A20
4. Functional Description
VDD
Si7007
1.25V
Ref
Calibration
Memory
Humidity
Sensor
Control Logic
ADC
SELECT
Temp
Sensor
PWM1
PWM2
PWM Interface
GND
Figure 5. Si7007 Block Diagram
The Si7007 is a digital relative humidity and temperature sensor that integrates temperature and humidity sensor
elements, an analog-to-digital converter, signal processing, calibration, polynomial non-linearity correction, and a
PWM output all in a single chip. The Si7007 is individually factory-calibrated for both temperature and humidity,
with the calibration data stored in on-chip, non-volatile memory. This ensures that the sensor is fully
interchangeable, with no recalibration or changes to software required. Patented use of industry-standard CMOS
and low-K dielectrics as a sensor enables the Si7007 to achieve excellent long term stability and immunity to
contaminants with low drift and hysteresis. The Si7007 offers a low power, high accuracy, calibrated and stable
solution ideal for a wide range of temperature, humidity, and dew-point applications including medical and
instrumentation, high reliability automotive and industrial systems, and cost-sensitive consumer electronics.
While the Si7007 is largely a conventional mixed-signal CMOS integrated circuit, relative humidity sensors in
general and those based on capacitive sensing using polymeric dielectrics have unique application and use
requirements that are not common to conventional (non-sensor) ICs. Chief among those are:
The need to protect the sensor during board assembly, i.e., solder reflow, and the need to subsequently
rehydrate the sensor.
The need to protect the sensor from damage or contamination during the product life-cycle.
The impact of prolonged exposure to extremes of temperature and/or humidity and their potential effect on
sensor accuracy.
The effects of humidity sensor “memory”.
Each of these items is discussed in more detail in the following sections.
Rev. 1.4
11
Si7007-A20
4.1. Relative Humidity Sensor Accuracy
To determine the accuracy of a relative humidity sensor, it is placed in a temperature and humidity controlled
chamber. The temperature is set to a convenient fixed value (typically 25–30 °C) and the relative humidity is swept
from 20 to 80% and back to 20% in the following steps: 20% – 40% – 60% – 80% – 80% – 60% – 40% – 20%. At
each set-point, the chamber is allowed to settle for a period of 60 minutes before a reading is taken from the
sensor. Prior to the sweep, the device is allowed to stabilize to 50%RH. The solid trace in Figure 6, “Measuring
Sensor Accuracy Including Hysteresis,” shows the result of a typical sweep.
Figure 6. Measuring Sensor Accuracy Including Hysteresis
The RH accuracy is defined as the dotted line shown in Figure 6, which is the average of the two data points at
each relative humidity set-point. In this case, the sensor shows an accuracy of 0.25%RH. The Si7007 accuracy
specification (Table 4) includes:
Unit-to-unit and lot-to-lot variation
Accuracy of factory calibration
Margin for shifts that can occur during solder reflow
The accuracy specification does not include:
Hysteresis (typically ±1%)
Effects from long term exposure to very humid conditions
Contamination of the sensor by particulates, chemicals, etc.
Other aging related shifts ("Long-term stability")
Variations due to temperature (see Drift vs. Temperature in Table 4). RH readings will typically vary with
temperature by less than 0.05% C.
12
Rev. 1.4
Si7007-A20
4.2. Hysteresis
The moisture absorbent film (polymeric dielectric) of the humidity sensor will carry a memory of its exposure
history, particularly its recent or extreme exposure history. A sensor exposed to relatively low humidity will carry a
negative offset relative to the factory calibration, and a sensor exposed to relatively high humidity will carry a
positive offset relative to the factory calibration. This factor causes a hysteresis effect illustrated by the solid trace
in Figure 6. The hysteresis value is the difference in %RH between the maximum absolute error on the decreasing
humidity ramp and the maximum absolute error on the increasing humidity ramp at a single relative humidity
setpoint and is expressed as a bipolar quantity relative to the average error (dashed trace). In the example of
Figure 6, the measurement uncertainty due to the hysteresis effect is ±1.0%RH.
4.3. Prolonged Exposure to High Humidity
Prolonged exposure to high humidity will result in a gradual upward drift of the RH reading. The shift in sensor
reading resulting from this drift will generally disappear slowly under normal ambient conditions. The amount of
shift is proportional to the magnitude of relative humidity and the length of exposure. In the case of lengthy
exposure to high humidity, some of the resulting shift may persist indefinitely under typical conditions. It is generally
possible to substantially reverse this effect by baking the device (see Section “4.6. Bake/Hydrate Procedure” ).
4.4. PCB Assembly
4.4.1. Soldering
Like most ICs, Si7007 devices are shipped from the factory vacuum-packed with an enclosed desiccant to avoid
any RH accuracy drift during storage and to prevent any moisture-related issues during solder reflow. The following
guidelines should be observed during PCB assembly:
Si7007 devices are compatible with standard board assembly processes. Devices should be soldered
using reflow per the recommended card reflow profile. (See Section “9. PCB Land Pattern and Solder
Mask Design” for the recommended card reflow profile.)
A "no clean" solder process is recommended to minimize the need for water or solvent rinses after
soldering. Cleaning after soldering is possible, but must be done carefully to avoid impacting the
performance of the sensor. (See “AN607: Si70xx Humidity Sensor Designer’s Guide” for more information
on cleaning.)
It is essential that the exposed polymer sensing film be kept clean and undamaged. This can be
accomplished by careful handling and a clean, well-controlled assembly process. When in doubt or for
extra protection, a heat-resistant, protective cover such as Kapton™ KPPD-1/8 polyimide tape can be
installed during PCB assembly.
Si7007s may be ordered with a factory-fitted, solder-resistant protective cover. This cover provides protection
during PCB assembly or rework but without the time and effort required to install and remove the Kapton tape. It
can be left in place for the lifetime of the product, preventing liquids, dust or other contaminants from coming into
contact with the polymer sensor film. See Section “7. Ordering Guide” for a list of ordering part numbers that
include the cover.
Rev. 1.4
13
Si7007-A20
4.4.2. Rehydration
The measured humidity value will generally shift slightly after solder reflow. A portion of this shift is permanent and
is accounted for in the accuracy specifications in Table 4. After soldering, an Si7007 should be allowed to
equilibrate under controlled RH conditions (room temperature, 45–55%RH) for at least 48 hours to eliminate the
remainder of the shift and return the device to its specified accuracy performance.
4.4.3. Rework
To maintain the specified sensor performance, care must be taken during rework to minimize the exposure of the
device to excessive heat and to avoid damage/contamination or a shift in the sensor reading due to liquids, solder
flux, etc. Manual touch-up using a soldering iron is permissible under the following guidelines:
The exposed polymer sensing film must be kept clean and undamaged. A protective cover is
recommended during any rework operation (Kapton® tape or the factory installed cover).
Flux must not be allowed to contaminate the sensor; liquid flux is not recommended even with a cover in
place. Conventional lead-free solder with rosin core is acceptable for touch-up as long as a cover is in
place during the rework.
If possible, avoid water or solvent rinses after touch-up. Cleaning after soldering is possible, but must be
done carefully to avoid impacting the performance of the sensor. See AN607 for more information on
cleaning.
Minimize the heating of the device. Soldering iron temperatures should not exceed 350 °C and the contact
time per pin should not exceed five seconds.
Hot air rework is not recommended. If a device must be replaced, remove the device by hot air and solder
a new part in its place by reflow following the guidelines above.
*Note: All trademarks are the property of their respective owners.
Figure 7. Si7007 with Factory-Installed Protective Cover
14
Rev. 1.4
Si7007-A20
4.5. Protecting the Sensor
Because the sensor operates on the principal of measuring a change in capacitance, any changes to the dielectric
constant of the polymer film will be detected as a change in relative humidity. Therefore, it is important to minimize
the probability of contaminants coming into contact with the sensor. Dust and other particles as well as liquids can
affect the RH reading. It is recommended that a cover is employed in the end system that blocks contaminants but
allows water vapor to pass through. Depending on the needs of the application, this can be as simple as plastic or
metallic gauze for basic protection against particulates or something more sophisticated such as a hydrophobic
membrane providing up to IP67 compliant protection.
The Si7007 may be ordered with a factory-fitted, solder-resistant cover that can be left in place for the lifetime of
the product. It is very low-profile, hydrophobic and oleophobic. See Section “7. Ordering Guide” for a list of ordering
part numbers that include the cover. A dimensioned drawing of the IC with the cover is included in Section “8.
Package Outline” . Other characteristics of the cover are listed in Table 9.
Table 9. Specifications of Protective Cover
Parameter
Value
PTFE
Material
Operating Temperature
–40 to 125 °C
260 °C
Maximum Reflow Temperature
IP Rating (per IEC 529)
IP67
4.6. Bake/Hydrate Procedure
After exposure to extremes of temperature and/or humidity for prolonged periods, the polymer sensor film can
become either very dry or very wet, in each case the result is either high or low relative humidity readings. Under
normal operating conditions, the induced error will diminish over time. From a very dry condition, such as after
shipment and soldering, the error will diminish over a few days at typical controlled ambient conditions, e.g.,
48 hours of 45 ≤ %RH ≤ 55. However, from a very wet condition, recovery may take significantly longer. To
accelerate recovery from a wet condition, a bake and hydrate cycle can be implemented. This operation consists of
the following steps:
Baking the sensor at 125 °C for ≥ 12 hours
Hydration at 30 °C in 75% RH for ≥ 10 hours
Following this cycle, the sensor will return to normal operation in typical ambient conditions after a few days.
4.7. Long Term Drift/Aging
Over long periods of time, the sensor readings may drift due to aging of the device. Standard accelerated life
testing of the Si7007 has resulted in the specifications for long-term drift shown in Table 4 and Table 5. This
contribution to the overall sensor accuracy accounts only for the long-term aging of the device in an otherwise
benign operating environment and does not include the effects of damage, contamination, or exposure to extreme
environmental conditions.
Rev. 1.4
15
Si7007-A20
5. PWM Output
During operation, the Si7007 takes a relative humidity and temperature measurement once per second and
converts the result into a pulse width modulated waveform. Two output pins are available for reading the
measurement results: PWM1 and PWM2. The information output on each pin is determined by the SELECT pin as
follows:
Table 10. PWM Outputs
Voltage on SELECT Pin
PWM1 Output
RH
PWM2 Output
Temperature
RH
High
Low
Temperature
The duty cycle of the waveform on the PWM outputs corresponds to the relative humidity and temperature results
shown in the following equations. The PWM duty cycle varies linearly with the measurement result between the
minimum and maximum values:
RH (%RH) = – 6 + 125 DCPWM
Where DCPWM is the ratio of high time to period (i.e., a number that varies from 0 to 1)
Equation 1.
T(°C) = – 46.85 + 175.72 DCPWM
Equation 2.
In the typical application, the PWM output is filtered using an RC network to provide an analog output voltage that
varies linearly with RH and temperature. See Section “2. Typical Application Circuits” for the recommended
application circuit.
Due to normal variations in RH accuracy of the device as described in Table 4, it is possible for the measured value
of %RH to be slightly less than 0 when the actual RH level is close to or equal to 0. Similarly, the measured value
of %RH may be slightly greater than 100 when the actual RH level is close to or equal to 100. This is expected
behavior.
16
Rev. 1.4
Si7007-A20
6. Pin Descriptions: Si7007 (Top View)
1
2
3
6
5
4
PWM1
GND
SELECT
VDD
DNC
PWM2
Pin Name
Pin #
Pin Description
PWM1
1
Pulse width modulated output #1
Ground. This pin is connected to ground on the circuit board through a trace. Do not
connect directly to GND plane.
GND
DNC
2
3
This pin should be soldered to pads on the PCB for mechanical stability. It can be electri-
cally floating or tied to V (do not tie to GND).
DD
PWM2
VDD
4
5
Pulse width modulated output #2
Power. This pin is connected to power on the circuit board.
Digital input that toggles between RH and temperature outputs on PWM1 and PWM2.
This pin should be pulled high or low (do not leave floating).
SELECT
6
This pad is connected to GND internally. This pad is the main thermal input to the on-
chip temperature sensor. The paddle should be soldered to a floating pad.
T
Paddle
GND
Rev. 1.4
17
Si7007-A20
7. Ordering Guide
Table 11. Device Ordering Guide
Max. Accuracy
Pkg
Operating
Range (°C)
Protective Packing
P/N
Description
Cover
Format
Temp
RH
Digital temperature/ humidity
sensor—industrial temp range
–40 to
+125 °C
Si7007-A20-IM
Si7007-A20-IMR
Si7007-A20-IM1
±1.0 °C ±5%
±1.0 °C ±5%
±1.0 °C ±5%
±1.0 °C ±5%
DFN 6
DFN 6
DFN 6
DFN 6
N
Cut Tape
Digital temperature/ humidity
sensor—industrial temp range
–40 to
+125 °C
Tape &
Reel
N
Y
Y
Digital temperature/ humidity
sensor—industrial temp range
–40 to
+125 °C
Cut Tape
Digital temperature/ humidity
sensor—industrial temp range
Si7007-A20-
IM1R
–40 to
+125 °C
Tape &
Reel
Note: The “A” denotes product revision A and “20” denotes firmware version 2.0.
18
Rev. 1.4
Si7007-A20
8. Package Outline
8.1. Package Outline: 3x3 6-pin DFN
Figure 10. 3x3 6-pin DFN
Table 12. 3x3 6-pin DFN Package Diagram Dimensions
Dimension
Min
Nom
Max
A
A1
b
0.70
0.00
0.35
0.75
0.02
0.80
0.05
0.45
0.40
D
3.00 BSC.
1.50
D2
e
1.40
1.60
1.00 BSC.
3.00 BSC.
2.40
E
E2
H1
H2
L
2.30
0.85
1.39
0.35
2.50
0.95
1.49
0.45
0.90
1.44
0.40
aaa
bbb
ccc
ddd
eee
fff
0.10
0.10
0.05
0.10
0.05
0.05
Notes:
1. All dimensions shown are in millimeters (mm).
2. Dimensioning and Tolerancing per ANSI Y14.5M-1994.
Rev. 1.4
19
Si7007-A20
8.2. Package Outline: 3x3 6-pin DFN with Protective Cover
Figure 8 illustrates the package details for the Si7007 with the optional protective cover. Table 13 lists the values
for the dimensions shown in the illustration.
Figure 8. 3x3 6-pin DFN with Protective Cover
Table 13. 3x3 6-pin DFN with Protective Cover Package Diagram Dimensions
Dimension
Min
—
Nom
—
Max
1.21
0.05
0.80
0.45
A
A1
A2
b
0.00
0.70
0.35
0.02
0.75
0.40
D
3.00 BSC.
1.50
D2
e
1.40
1.60
1.00 BSC.
3.00 BSC.
2.40
E
E2
F1
F2
h
2.30
2.70
2.70
0.76
0.35
0.45
2.50
2.90
2.90
0.90
0.45
0.55
2.80
2.80
0.83
L
0.40
R1
aaa
bbb
ccc
ddd
eee
0.50
0.10
0.10
0.05
0.10
0.05
Notes:
1. All dimensions are shown in millimeters (mm).
2. Dimensioning and Tolerancing per ANSI Y14.5M-1994.
20
Rev. 1.4
Si7007-A20
9. PCB Land Pattern and Solder Mask Design
Figure 9. Si7007 PCB Land Pattern
Table 14. PCB Land Pattern Dimensions
Symbol
C1
mm
2.90
1.00
1.60
2.50
0.45
0.85
E
P1
P2
X1
Y1
Notes:
General
1. All dimensions shown are at Maximum Material Condition (MMC). Least Material
Condition (LMC) is calculated based on a Fabrication Allowance of 0.05 mm.
2. This Land Pattern Design is based on the IPC-7351 guidelines.
Solder Mask Design
3. All metal pads are to be non-solder mask defined (NSMD). Clearance between the
solder mask and the metal pad is to be 60 µm minimum, all the way around the
pad.
Stencil Design
4. A stainless steel, laser-cut and electro-polished stencil with trapezoidal walls
should be used to assure good solder paste release.
5. The stencil thickness should be 0.125 mm (5 mils).
6. The ratio of stencil aperture to land pad size should be 1:1 for all perimeter pins.
7. A 2x1 array of 1.00 mm square openings on 1.30 mm pitch should be used for the
center ground pad to achieve a target solder coverage of 50%.
Card Assembly
8. A No-Clean, Type-3 solder paste is recommended.
9. The recommended card reflow profile is per the JEDEC/IPC J-STD-020
specification for Small Body Components.
Rev. 1.4
21
Si7007-A20
10. Top Marking
10.1. Si7007 Top Marking
10.2. Top Marking Explanation
Mark Method:
Font Size:
Laser
0.30 mm
Pin 1 Indicator:
Line 1 Marking:
Circle = 0.30 mm Diameter
Upper-Left Corner
TTTT = Mfg Code
22
Rev. 1.4
Si7007-A20
11. Additional Reference Resources
AN607: Si70xx Humidity Sensor Designer’s Guide
Rev. 1.4
23
Si7007-A20
DOCUMENT CHANGE LIST
Revision 0.9 to Revision 1.0
Updated Table 2.
Updated Table 3.
Revision 1.0 to Revision 1.1
Updated Table 11.
Revision 1.1 to Revision 1.2
Updated Section “4.5. Protecting the Sensor”
Updated Table 9 on page 15 and Table 10 on
page 16
UpdateTable 13 on page 20 dimensions F1 and F2.
Revision 1.2 to Revision 1.3
Updated PWM Duty Cycle parameter in Table 3 on
page 5.
Updated Equation 1 and Equation 2 on page 16.
Revision 1.3 to Revision 1.4
Changed packing format from tube to cut tape for all
non-tape & reel part numbers without protective filter
covers.
24
Rev. 1.4
Smart.
Connected.
Energy-Friendly
Products
www.silabs.com/products
Quality
www.silabs.com/quality
Support and Community
community.silabs.com
Disclaimer
Silicon Laboratories intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers
using or intending to use the Silicon Laboratories products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific
device, and "Typical" parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Laboratories
reserves the right to make changes without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy
or completeness of the included information. Silicon Laboratories shall have no liability for the consequences of use of the information supplied herein. This document does not imply
or express copyright licenses granted hereunder to design or fabricate any integrated circuits. The products must not be used within any Life Support System without the specific
written consent of Silicon Laboratories. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected
to result in significant personal injury or death. Silicon Laboratories products are generally not intended for military applications. Silicon Laboratories products shall under no
circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons.
Trademark Information
Silicon Laboratories Inc., Silicon Laboratories, Silicon Labs, SiLabs and the Silicon Labs logo, CMEMS®, EFM, EFM32, EFR, Energy Micro, Energy Micro logo and combinations
thereof, "the world’s most energy friendly microcontrollers", Ember®, EZLink®, EZMac®, EZRadio®, EZRadioPRO®, DSPLL®, ISOmodem ®, Precision32®, ProSLIC®, SiPHY®,
USBXpress® and others are trademarks or registered trademarks of Silicon Laboratories Inc. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of
ARM Holdings. Keil is a registered trademark of ARM Limited. All other products or brand names mentioned herein are trademarks of their respective holders.
Silicon Laboratories Inc.
400 West Cesar Chavez
Austin, TX 78701
USA
http://www.silabs.com
相关型号：
Si7007-A20-IMR
This change is considered a minor change which does not affect form, fit, function, quality, or reliability.
SILICON
SI7013-A10-YM0
Serial Switch/Digital Sensor, 14 Bit(s), 0.40Cel, Square, Surface Mount, 3 X 3 MM, DFN-10
SILICON
©2020 ICPDF网 联系我们和版权申明