GPFC110-12 [SLPOWER]

110 Watt Global Performance Switchers; 110瓦的全球绩效切换器


型号：	GPFC110-12
厂家：	SL Power Electronics
描述：	110 Watt Global Performance Switchers 110瓦的全球绩效切换器
文件：	总2页 (文件大小：363K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

GPFC110 Commercial

110 Watt Global Performance Switchers

110 WATT GLOBAL PERFORMANCE SWITCHERS

FEATURES:

• 3.1 watts/cu.in. power density

• Compact size (6.3” x 3.75” x 1.62”;

meets 1U height)

• Power factor corrected to IEC 1000-3-2 Class A

• Less than 300 μA leakage

• EMI compliance to CISPR 22, FCC Class B

• Approved to UL1950, IEC950 and

CSA 22.2 No. 950

• 2-year warranty

•

marked to LVD

• RoHS Compliant Model Available (G suﬃx)

SPECIFICATIONS

EMI/EMC Compliance

All models include built-in EMI ﬁltering to meet the EMC requirements below.

Ac Input

85-264 Vac, 47-63 Hz single phase.

Input Current

EMI SPECIFICATIONS

COMPLIANCE LEVEL

Maximum input current 2.3 A at 90 Vac, 60 Hz with full rated load. Input cur-

rent harmonic content meets the requirements of IEC1000-3-2.

Conducted Emissions

Static Discharge

RF Field Susceptibility

Fast Transients/Bursts

Surge Susceptibility

Line Frequency Harmonics

EN55022 Class B; FCC Class B

EN61000-4-2, 6 kV contact, 8 kV air

EN61000-4-3, 3 V/meter

EN61000-4-4, 2 kV, 5 kHz

EN61000-4-5, 1 kV diﬀ., 2 kV com.

EN61000-3-2 Class A

Hold-up Time

25 ms minimum from loss of ac input at full load, nominal line (115 Vac).

Output Power

110 W fan cooled, 75 W convection. Peak ratings are for 60 s maximum dura-

tion, 10% duty cycle.

Inrush Current

Total Regulation

Inrush 240 Vac is less than 37 A, averaged over the ﬁrst ac half-cycle under cold

start conditions. Limiting provided by internal thermistors.

Total regulation is the maximum deviation from the nominal voltage for all

steady-state loading conditions.

Fan Output

Overload Protection

An additional output, same as Vout, suitable for powering a dc fan is included in all

models. The output is protected by an internal resistor in the event of an overload.

Fully protected against short circuit and output overload. Short circuit protec-

tion is cycling type power limit. Recovery after fault is automatic.

Output Noise

Power Fail

0.5% rms, 1% pk-pk, 20 MHz Bandwidth, diﬀerential mode. Measured with

noise probe directly across output terminals of the power supply.

TTL or CMOS compatible output goes low (<0.5 V) 8 ms before output voltage

drops more than 4% below nominal voltage upon loss of ac power. The signal is

factory set to trip when input power can no longer sustain the output.

Transient Response

500 μs typical response time for return to within 0.5% of ﬁnal value for a 50%

load step change, ∆i/∆ t< 0.2 A/μs. Maximum voltage deviation is 3.5%. Load

must not go below stated minimum.

Temperature Coeﬃcient

0.03%/°C typical on all outputs.

Environmental

Remote Sense

Designed for 0 to 50°C operation at full rated output power; derate output current

and total output power by 2.5% per °C above 50°C. See Environmental and Pack-

aging Speciﬁcations on the next page.

Provided as a standard feature. Capable of compensating for 0.25 V total of

cabling losses in voltage. Open sense lead protection.

Overvoltage Protection

OVP crowbar reduces output voltage below nominal rating in less than 50 ms.

Commercial Safety Approvals

All models are approved to UL1950, CSA22.2 No. 950-95, IEC950, EN60950. CB

certiﬁcate available. Exceeds FCC and CISPR22 Class B conducted emissions

requirement

Voltage Adjustment: Main output 5%.

Input Protection

Internal ac fuse provided on all models. Fuse does not blow on overload or

short circuit—fuse blows only if catastrophic failure occurs in the unit.

All speciﬁcations are typical at nominal input, full load at 25^OC unless otherwise stated

Commercial

Model

Output

Minimum (A)

Output

Maximum (A)

Output

Maximum (B)

Total

Regulation

Output No.

Output

5.1 v

12 V

OVP Setpoint

6.2 0.6 V

14 1.1 V

18.5 1.5 V

28 2.5 V

34 2.8 V

55 4 V

Notes

GPFC 110-5

GPFC 110-12

GPFC 110-15

GPFC 110-24

GPFC110-28

GPFC110-48

0 A

11 A

6.7 A

5.3 A

3.4 A

2.9 A

1.7 A

15 A

9.2 A

7.3 A

4.6 A

3.9 A

2.3 A

15 V

24 V

28 V

48 V

Notes:

A. With unrestricted convection cooling.

B. With 26cfm airﬂow.

C. Add “G”suﬃx to part number for RoHS compliant model.

GPFC110 MECHANICAL SPECIFICATIONS

ENVIRONMENTAL SPECIFICATIONS OPERATING

NON-OPERATING

-40 to +85°C

Temperature (A)

Humidity (A)

Shock (B)

See Individual Specs.

0 to 95% RH

A. Units should be allowed to warm up/operate under non-condensing

conditions before application of power.

B. Shock testing—half-sinusoidal, 10 3 ms duration, direction,

3 orthogonal axes, total 6 shocks.

0 to 95% RH

20 g_pk

40 g_pk

C. Random vibration—10 to 2000Hz, 6dB/octave roll-oﬀ from 350 to

2000Hz, 3 orthogonal axes. Tested for 10 min./axis operating and

1 hr./axis non-operating.

Altitude

-500 to 10,000 ft

1.5 g _rms’0.003 g²/Hz

-500 to 40,000 ft

5 g _rms’0.026 g²/Hz

Vibration (C)

SL Power Electronics Inc. The information and speciﬁcations contained in this data sheet are believed to be correct at time of publication.

However, SL Power accepts no responsibility for consequences arising from reproduction errors or inaccuracies. Speciﬁcations are subject to change without notice.

相关型号：