GPM41-24 [SLPOWER]

Power Supply Module;


型号：	GPM41-24
厂家：	SL Power Electronics
描述：	Power Supply Module 输出元件
文件：	总2页 (文件大小：200K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

GPC41 Commercial/GPM41 Medical

41 WATT GLOBAL PERFORMANCE SWITCHERS

GLOBAL PERFORMANCE SWITCHERS

Summary:

D C P o w e r S u p p l i e s

• Ultra small (2.00” x 4.00” x 1.50”)

• Wide-range ac input 85-264 Vac

• 2-year warranty

• Conducted EMI exceeds FCC Class B and CISPR

22 Class B (Commercial models) and CISPR 11

Class B (Medical models)

• Commercial Approved to UL1950, IEC950,

EN60950 and CSA22.2-234 L3

• Medical Approved to UL2601-1, IEC601-1 and

CSA22.2 No. 601

• RoHS Compliant (G suﬃx)

•

marked to LVD

SPECIFICATIONS

Ac Input

Output Noise

85-264 Vac, 47-63 Hz single phase.

0.5% rms, 1% pk-pk, 20 MHz bandwidth, diﬀerential mode. Measured with noise

probe directly across output terminals of the power supply.

Input Current

Maximum input current at 120 Vac, 60 Hz with full rated output load: 1.3 A

Transient Response

Hold-Up Time

Main output—500 μs typical response time for return to within 0.5% of ﬁnal value

for a 50% load step change. ∆i/ ∆t<0.2 A/μs. Maximum voltage deviation is 3.5%.

Startup/ shutdown overshoot less than 3%.

20 ms minimum from loss of ac input at full load, nominal line (115 Vac).

Output Power

40 W continuous, 50 W peak. Peak ratings are for 60 s maximum duration,

10% duty cycle. During peak load condition, output regulation may exceed

total regulation limits.

EMI/EMC Compliance

All models include built-in EMI ﬁltering to meet the

following emissions requirements:

Overload Protection

Fully protected against short circuit and output overload.

Short circuit protection is cycling type power limit.

EMI SPECIFICATIONS

COMPLIANCE LEVEL

Recovery after fault is automatic. Factory set to begin power limiting at ap-

proximately 55 W. See output ratings chart for additional notes or conditions.

Conducted Emissions GPC41

Conducted Emissions GPM41

Static Discharge

RF Field Susceptibility

Fast Transients/Bursts

Surge Susceptibility

EN55022 Class B; FCC Class B

EN55011 Class B; FCC Class B

EN61000-4-2, 6 kV contact, 8 kV air

EN61000-4-3, 3 V/meter

EN61000-4-4, 2 kV, 5 kH

EN61000-4-5, 1 kV diﬀ., 2 kV com.

Overvoltage Protection.

See output ratings chart.

Eﬃciency

69-77% at full rated load, nominal input voltage, depending

on model.

Commercial Leakage Current

60 μA single fault; 60 Hz input.

Turn-on Time

Less than 1 s at 120 Vac, 25°C (inversely proportional to input voltage).

Commercial Safety

Input Protection

Approved to UL1950, CSA22.2 No. 234 Level 3, IEC950 and EN60950. UL ﬁle

#E135803 commercial; CSA #LR46516 all models. All dc outputs are SELV under

normal and single fault conditions.

Requires external ac line fusing. A 2.5 A, 250 V rated fuse with I2t > 20 is

recommended.

Inrush Current

Inrush is limited by internal thermistor. Inrush at 240 Vac under cold start

conditions will not exceed 34 A.

Medical Leakage Current

35 μA , 254 Vac 60 Hz input.

Temperature Coeﬃcient

0.03%/°C typical on all outputs.

Medical Safety

Approved to UL2601, CSA22.2 No. 601 Level 3, IEC601.

UL ﬁle E116994; CSA #LR46516. The output(s) are intended for safety earthed Sig-

nal Output and Intermediate Circuits only. The output(s) are not acceptable for

patient connection without additional isolation. All dc outputs are SELV under

normal and single fault conditions.

Environmental

Designed for 0 to 50°C operation at full rated output

power; derate output current and total output power by

2.5% per °C above 50°C. See Environmental and

Packaging Speciﬁcations on next page.

All speciﬁcations are typical at nominal input, full load at 25^OC unless otherwise stated

Commercial

Model

Medical

Model

Minimum

Load

Regulation

Initial Setpoint

Tolerance

OVP

Setpoint

Ripple and

Noise

Output

5.1 V

12 V

Current

6.0 A

3.3 A

2.7 A

1.7 A

1.4 A

GPC41-5

GPM41-5

0.15

0.03

0.01

0.75%

6.2 0.6 V

14 1.0 V

19 1.5 V

28 2.5 V

34 2.8 V

GPC41-12

GPC41-15

GPC41-24

GPC41-28

GPM41-12

GPM41-15

GPM41-24

15 V

24 V

28 V

Note: Add “G”suﬃx to model number for RoHS compliant model.

GPC41/GPM41 MECHANICAL SPECIFICATIONS

ENVIRONMENTAL SPECIFICATIONS

OPERATING

See individual specs.

NON-OPERATING

-40 to +85°C

Temperature (A)

Humidity (A)

Shock (B)

0 to 95% RH

20 g_pk

40 g_pk

Altitude

-500 to 10,000 ft

-500 to 40,000 ft

Vibration (C)

1.5 g _rms’0.003 g²/Hz

5 g _rms’0.026 g²/Hz

A. Units should be allowed to warm up/operate under non-condensing conditions before application of power. Derate output

current and total output power by 2.5% per °C above 50°C. For operation in a conﬁned space, moving air may be required. Under

all conditions, the cooling vs. load proﬁle should be such that heat sinks and/or heatsink temperatures do not exceed 90 °C for

extended periods.

B. Shock testing—half-sinusoidal, 10 3 ms duration, direction, 3 orthogonal axes, total 6 shocks.

C. Random vibration—10 to 2000Hz, 6dB/octave roll-oﬀ from 350 to 2000Hz, 3 orthogonal axes. Tested for 10 min./axis operating

and 1 hr./axis non-operating.

SL Power Electronics Corp., 6050 King Drive, Bldg.A, Ventura, CA, 93003, USA. Phone:(805) 486 4565 Fax:(805) 487 8911 Email: info@slpower.com. Rev. 4/08.

However, SL Power accepts no responsibility for consequences arising from reproduction errors or inaccuracies. Speciﬁcations are subject to change without notice.

相关型号：