C-13-622-T-SSC [SOURCE]
Transceiver, 1274nm Min, 1356nm Max, 622Mbps(Tx), 622Mbps(Rx), SC Connector, Through Hole Mount;
| 型号： | C-13-622-T-SSC |
| 厂家： | 
SOURCE PHOTONICS, INC. |
| 描述： | Transceiver, 1274nm Min, 1356nm Max, 622Mbps(Tx), 622Mbps(Rx), SC Connector, Through Hole Mount |
| 文件： | 总8页 (文件大小：648K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
622 Mbps Single Mode SFF LC Transceiver
C-1X-622C-F(DFB)-SLC(4)
Features
• Duplex LC Single Mode Transceiver
• Small Form Factor Multi-soured 2 x 5 Pin Package
• Complies with ITU-T/STM-4, OC-12
• 1310nm / 1550nm Wavelength, FP / DFB Laser
• Single+3.3V Power Supply
• LVPECL Differential Inputs and Outputs
• LVTTL Signal Detection Output
• Class 1 Laser International Safety Standard IEC 825 Compliant
• Solder ability to MIL-STD-883, Method 2003
• Pin coating is Sn/Pb with minimum 2% Pb content
• Flammability to UL94V0
• Humidity RH 5-85% (5-95% short term) to IEC 68-2-3
• Complies with Bell core GR-468-CORE
• Uncooled laser diode with MQW structure
• ATM 622 Mbps Links application
• SONET/SDH Equipment Interconnect application
Absolute Maximum Rating
Parameter
Symbol
Vcc
Min.
Max.
3.6
30
Unit
V
Note
Power Supply Voltage
Output Current
0
0
Iout
mA
ºC
Soldering Temperature
Storage Temperature
-
260
85
10 seconds on leads only
-
Tstg
-40
ºC
Recommended Operating Condition
Parameter
Symbol
Min.
3.1
-5
Typ.
3.3
-
Max.
3.5
70
Unit
Note
Power Supply Voltage
Operating Temperature (Case)
Operating Temperature (Case)
Data Rate
Vcc
Topr
Topr
-
V
ºC
C-1X-622C-F(DFB)-SLC(4)
C-1X-622C-F(DFB)-SLC(4)A
-40
-
-
85
ºC
622
-
Mbps
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
LUMINENTOIC.COM
LUMNDS583-Jun2405
rev. A.2
1
622 Mbps Single Mode SFF LC Transceiver
C-1X-622C-F(DFB)-SLC(4)
Transmitter Specifications
Parameter
Symbol
Min
Typical
Max
Unit
Notes
Optical
Po
Po
-15
-3
-
-8
+2
1356
1335
1580
2.5
1
dBm
dBm
nm
nm
nm
nm
nm
dB
C-13-622C-F-SLC
Optical Transmit Power
Optical Transmit Power
Output center Wavelength
Output center Wavelength
Output center Wavelength
Output Spectrum Width
Output Spectrum Width
Side Mode Suppression Ratio
Extinction Ratio
-
C-1X-622C-FDFB-SLC4
C-13-622C-F-SLC
λp
1274
1280
1480
-
1310
λp
1310
C-13-622C-FDFB-SLC4
C-15-622C-FDFB-SLC4
RMS(σ), C-13-622C-F-SLC
-20 dB width, C-1X-622C-FDFB-SLC4
C-1X-622C-FDFB-SLC4
C-13-622C-F-SLC
λp
1550
∆λrms
∆λ
Sr
-
-
-
30
35
-
-
ER
8.2
10
-
dB
Extinction Ratio
ER
-
-
dB
C-1X-622C-FDFB-SLC4
Output Eye
Compliant with ITU-T G.957/STM-4 Eye Mask
Optical Rise Time
tr
tf
-
-
-
-
-
-
1.2
1.2
ns
ns
10% to 90% Values
10% to 90% Values
Optical Fall Time
Relative Intensity Noise
RIN
-120
dB/Hz
Measured with 223-1 PRBS with 72 ones
and 72 zeros.
Total Jitter
TJ
-
-
0.55
ns
Transmitter Specifications
Parameter
Symbol
Min
Typical
Max
Unit
Notes
Electrical
Maximum current is specified at Vcc=
Maximum @ maximum temperature
ICC
-
-
160
mA
Supply Current
Transmitter Enable Voltage
Transmitter Disable Voltage
Data Input Current-Low
Data Input Current-High
Data Input Voltage-Low
Data Input Voltage-High
VEN
VD
IIL
0
2
-
-
-
-
-
-
0.8
Vcc
-
V
V
-200
-
µA
µA
V
I
200
-1.58
-0.74
IH
VIL-VCC
VIH-VCC
-2.0
-1.1
These inputs are compatible with 10K,
10KH and 100K ECL and PECL inputs
V
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
LUMINENTOIC.COM
LUMNDS583-Jun2405
rev. A.2
2
622 Mbps Single Mode SFF LC Transceiver
C-1X-622C-F(DFB)-SLC(4)
Receiver Specifications
Parameter
Symbol
Min
Typical
Max
Unit
Notes
Optical
-10
23
Sensitivity
-
-
-3
-
-
-
-
-
-
-28
dBm
dBm
dBm
dBm
dB
Measured with 2 -1 PRBS, BER=10
Maximum Input Power
Signal Detect-Asserted
Signal Detect-Deasserted
Signal Detect-Hysteresis
Wavelength of Operation
Pin
Pa
Pd
-
-28
-
-
Measured on transition: low to high
Measured on transition: high to low
-40
1
5
1100
1600
nm
Receiver Specifications
Parameter
Symbol
Min
Typical
Max
Unit
Note
Electrical
ICC
-
-2.0
-1.1
-
-
-
-
-
-
120
-1.58
-0.74
0.5
mA
V
The current excludes the output load current
Supply Current
Data Output Voltage-Low
Data Output Voltage-High
Signal Detect Output Voltge-Low
Signal Detect Output Voltage-High
VOL -Vcc
These outputs are compatible with 10K,
10KH and 100KECL and PECL outputs
VOH-
V
Vcc
VSDL
VSDH
V
LVTTL
2
Vcc
V
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
LUMINENTOIC.COM
LUMNDS583-Jun2405
rev. A.2
3
622 Mbps Single Mode SFF LC Transceiver
C-1X-622C-F(DFB)-SLC(4)
Connection Diagram
PIN
Symbol
RxGND
RxVcc
SD
Notes
Directly connect this pin to the receiver ground plane
+3.3V dc power for the receiver section
Active high on this indicates a received optical signal(LVTTL)
Receiver Data Out Bar (LVPECL)
1
2
3
4
5
6
7
RD-
RD+
Receiver Data Out (LVPECL)
TxVcc
TxGND
TxDIS
TD+
+3.3V dc power for the trasmitter section
Directly connect this pin to the transmitter ground plane
Transmitter disable (LVTTL)
8
9
Transmitter Data In (LVPECL)
10
TD-
Transmitter Data In Bar (LVPECL)
The attaching posts are at case potential and may be connected to chassis
ground. They are isolated from circuit ground.
Attaching Posts
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
LUMINENTOIC.COM
LUMNDS583-Jun2405
rev. A.2
4
622 Mbps Single Mode SFF LC Transceiver
C-1X-622C-F(DFB)-SLC(4)
Recommended Circuit Schematic
Vcc(+3.3V)
TERMINATE AT
TRANSCEIVER INPUTS
Z=50
Z=50
TD-
TD
LVPECL
100
130
Vcc(+3.3V)
130
10
9
8
7
6
1
H
10
F
C2
C3
Tx
Rx
Vcc(+3.3V)
1
H
C1
RD+
RD-
SD
1
2
3
4
5
Z=50
100
LVPECL
Z=50
Z=50
130
130
TERMINATE AT
DEVICE INPUTS
NOTE:C1=C2=C3=100nF
The split-loaded terminations for ECL signals need to be located at the input of devices receiving those ECL signals.
The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc.
A GND plane under the module is required for good EMI and sensitivity performance.
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
LUMINENTOIC.COM
LUMNDS583-Jun2405
rev. A.2
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
5
622 Mbps Single Mode SFF LC Transceiver
C-1X-622C-F(DFB)-SLC(4)
Printed Circuit Board Layout Consideration
A fiber-optic receiver employs a very high gain, wide bandwidth transimpedance amplifier. This amplifier detects and amplifies
signals that are only tens of nA in amplitude when the receiver is operating near it’s limit. Any unwanted signal current that couples into the
receiver circuitry causes a decrease in the receiver’s sensitivity and can also degrade the performance of the receiver’s signal detect (SD) circuit.
To minimize the coupling of unwanted noise into the receiver, careful attention must be given to the printed circuit board.
At a minimum, a double-sided printed circuit board(PCB) with a large component side ground plane beneath the transceiver must
be used. In applications that include many other high speed devices, a multi-layer PCB is highly recommended. This permits the placement of
power and ground on separate layers, wich allows them to be isolated from the signal lines. Multilayer construction also permits the routing of
signal traces away from high level, high speed sinal lines. To minimize the possibility of coupling noise into the receiver section, high level, high
speed signals such as transmitter inputs and clock lines should be routed as far away as possible from the receiver pins.
Noise that couples into the receiver through the power supply pins can also degrade performance. It is recommended that a pi filter
be used in both transmitter and receiver power supplies.
EMI and ESC Consideration
LuminentOIC transceivers offer a metalized plastic case and a special chassis grounding clip. As shown in the drawing, this clip connects
the module case to chassis ground then installs flush through the panel cutout. This way, the grounding clip brushes the edge of the cutout in
order to make a proper contact. The use of a grounding clip also provides increased electrostatic protection and helps reduce radiated emission
from the module or the host circuit board through the chassis faceplate. The attaching posts are at case potential and may be connected to chassis
ground. They should not be connected to circuit ground.
Plastic optical subassemblies are used to further reduce the possibility of radiated emission by eliminating the metal from the
transmitter and receiver diode housings, which extend into connector space. By providing a non-metal receptacle for the optical cable ferrule, the
gigabit speed RF electrical signal is isolated from the connector area thus preventing radiated energy leakage from these surfaces to the outside of
the panel.
Recommended Board Layout Hole Pattern
DIMENSION IN MILLIMETER (INCHES)
NOTES:
1.THIS FIGURE DESCRIBE THE RECOMMAND CIRCUIT BOARD LAYOUT FOR THE SFF TRANSCEIVER.
2.THE HATCHED AREAS ARE KEEP-OUT AREAS RESERVED FOR HOUSING STANDOFF. NO METAL
TRACES OR GROUND CONNECTION IN KEEP-OUT AREAS.
3.THE MOUNTING STUDS SHOULD BE SOLDERED TO CHASSIS GROUND FOR MECHANICAL INTEGRITY.
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
LUMINENTOIC.COM
LUMNDS583-Jun2405
rev. A.2
6
622 Mbps Single Mode SFF LC Transceiver
C-1X-622C-F(DFB)-SLC(4)
Recommended Panel mounting
DIMENSION IN MILLIMETER (INCHES)
Package Diagram
Units: mm (inches)
+0
8.8
-0.
+(
)
(1.921)
-(0.008)
6.9
(0.274)
.95
1.50
(0.3)
(0.)
(0.413)
(0.020)
2
�
7
(0.246)
(0.039±0.002)
72
(0.070)
(0.280)
(0.200)
77
(0.700)
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
LUMINENTOIC.COM
LUMNDS583-Jun2405
rev. A.2
7
622 Mbps Single Mode SFF LC Transceiver
C-1X-622C-F(DFB)-SLC(4)
Ordering Information
Available Options:
C-13-622C-F-SLC
C-13-622C-FDFB-SLC4
C-15-622C-FDFB-SLC4
C-13-622C-F-SLCA
C-13-622C-FDFB-SLC4A
C-15-622C-FDFB-SLC4A
Part numbering Definition:
C - 1X - 622C - F(DFB)
-
S
LC TxPower Temperature Range
• 13 = Wavelength 1310nm
15 = Wavelength 1550nm
• Communication protocol
622C=LVTTL SD output
• F = +3.3V SFF Transceiver, FP
FDFB = +3.3V SFF Transceiver, DFB
• Single mode fiber
• Connector options
• Tx Power range
Blank = -15 to -8 dBm
4 = -3 to +2 dBm
• Temperature range
Blank = commercial temperature(-5 to 70 ºC)
A = industrial temperature(-40 to 85 ºC)
Warnings:
Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow
guidelines according to proper ESD procedures.
Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation.
Legal Notes:
IMPORTANT NOTICE!
All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance
of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are
given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warran-
ties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of
Sale for further warranty information.
LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual
property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes
no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this docu-
ment are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers
using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from
such use or sale.
THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any
actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact
LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current.
© LuminentOIC, Inc. 2003
All rights reserved
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
LUMINENTOIC.COM
LUMNDS583-Jun2405
rev. A.2
8
相关型号：
C-13-622-T-SSC-G5
Transceiver, 1274nm Min, 1356nm Max, 622Mbps(Tx), 622Mbps(Rx), SC Connector, Through Hole Mount, 10.40 MM HEIGHT, PACKAGE-9
SOURCE
©2020 ICPDF网 联系我们和版权申明