AM29SL800DB-120WCI_技术文档

Am 29SL800D

Data Sheet

July 2003

The following document specifies Spansion memory products that are now offered by both Advanced

Micro Devices and Fujitsu. Although the document is marked with the name of the company that orig-

inally developed the specification, these products will be offered to customers of both AMD and

Fujitsu.

Continuity of Specifications

There is no change to this datasheet as a result of offering the device as a Spansion product. Any

changes that have been made are the result of normal datasheet improvement and are noted in the

document revision summary, where supported. Future routine revisions will occur when appropriate,

and changes will be noted in a revision summary.

Continuity of O rdering Part Num bers

AMD and Fujitsu continue to support existing part numbers beginning with “Am” and “MBM”. To order

these products, please use only the Ordering Part Numbers listed in this document.

For More Inform ation

Please contact your local AMD or Fujitsu sales office for additional information about Spansion

memory solutions.

Publication Number 27546 Revision A Amendment +4 Issue Date April 27, 2005

This Page Left Intentionally Blank.

Am29SL800D

8 Megabit (1 M x 8-Bit/512 K x 16-Bit)

CMOS 1.8 Volt-only Super Low Voltage Flash Memory

Data Sheet

Distinctive Characteristics

Single Power Supply Operation

Embedded Algorithms

— 1.65 to 2.2 V for read, program, and erase

operations

— Embedded Erase algorithm automatically

preprograms and erases the entire chip or any

combination of designated sectors

— Ideal for battery-powered applications

Manufactured on 0.23 µm Process Technology

— Compatible with 0.32 µm Am29SL800C device

High Performance

— Embedded Program algorithm automatically

writes and verifies data at specified addresses

Minimum 1,000,000 Erase Cycle Guarantee Per

Sector

— Access times as fast as 90 ns

20-Year Data Retention at 125°C

Package Option

Ultra Low Power Consumption (Typical Values at

5 MHz)

— 48-pin TSOP

— 0.2 µA Automatic Sleep Mode current

— 0.2 µA standby mode current

— 5 mA read current

— 48-ball FBGA

Compatibility with JEDEC Standards

— 15 mA program/erase current

— Pinout and software compatible with single-

power supply Flash

Flexible Sector Architecture

— Superior inadvertent write protection

— One 16 Kbyte, two 8 Kbyte, one 32 Kbyte, and

fifteen 64 Kbyte sectors (byte mode)

Data# Polling and Toggle Bits

— One 8 Kword, two 4 Kword, one 16 Kword, and

fifteen 32 Kword sectors (word mode)

— Provides a software method of detecting program

or erase operation completion

— Supports full chip erase

Ready/Busy# Pin (RY/BY#)

— Sector Protection Features:

— Provides a hardware method of detecting

program or erase cycle completion

A hardware method of locking a sector to prevent any

program or erase operations within that sector

Erase Suspend/Erase Resume

Sectors can be locked in-system or via programming

equipment

— Suspends an erase operation to read data from,

or program data to, a sector that is not being

erased, then resumes the erase operation

Temporary Sector Unprotect feature allows code

changes in previously locked sectors

Hardware Reset Pin (RESET#)

Unlock Bypass Program Command

— Hardware method to reset the device to reading

array data

— Reduces overall programming time when issuing

multiple program command sequences

Top or Bottom Boot Block Configurations

Available

Publication# 27546 Rev: A Amendment/+4

Issue Date: April 27, 2005

This document contains information on a product under development at Advanced Micro Devices. The information

is intended to help you evaluate this product. AMD reserves the right to change or discontinue work on this proposed

product without notice.

Refer to AMD’s Website (www.amd.com) for the latest information

D a t a S h e e t

Table of Contents

Table 6. Write Operation Status ..................................................... 25

Absolute Maximum Ratings. . . . . . . . . . . . . . . . . 26

Figure 7. Maximum Negative Overshoot Waveform Maximum

Negative Overshoot Waveform...................................................... 26

Figure 8. Maximum Positive Overshoot Waveform........................ 26

Operating Ranges. . . . . . . . . . . . . . . . . . . . . . . . . 26

DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 27

Table 7. CMOS Compatible ........................................................... 27

Zero Power Flash ................................................................... 28

Product Selector Guide . . . . . . . . . . . . . . . . . . . . . 3

Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Connection Diagrams . . . . . . . . . . . . . . . . . . . . . . 5

Special Handling Instructions for FBGA Packages .................. 6

Pin Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . 7

Logic Symbol . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Ordering Information. . . . . . . . . . . . . . . . . . . . . . . 8

Standard Products .................................................................... 8

Device Bus Operations . . . . . . . . . . . . . . . . . . . . 10

Table 1. Am29SL800D Device Bus Operations ..............................10

Word/Byte Configuration ........................................................ 10

Requirements for Reading Array Data ................................... 10

Writing Commands/Command Sequences ............................ 10

Program and Erase Operation Status .................................... 11

Standby Mode ........................................................................ 11

Automatic Sleep Mode ........................................................... 11

RESET#: Hardware Reset Pin ............................................... 11

Output Disable Mode .............................................................. 12

Table 2. Am29SL800DT Top Boot Block Sector Address Table .....12

Table 3. Am29SL800DB Bottom Boot Block Sector

Address Table .................................................................................13

Autoselect Mode ..................................................................... 14

Table 4. Am29SL800D Autoselect Code (High Voltage Method) ...14

Sector Protection/Unprotection ............................................... 14

Temporary Sector Unprotect .................................................. 14

Figure 1. In-System Sector Protect/Unprotect Algorithms .............. 15

Figure 2. Temporary Sector Unprotect Operation........................... 16

Hardware Data Protection ...................................................... 16

Command Definitions . . . . . . . . . . . . . . . . . . . . . 16

Reading Array Data ................................................................ 16

Reset Command ..................................................................... 16

Autoselect Command Sequence ............................................ 17

Word/Byte Program Command Sequence ............................. 17

Figure 3. Program Operation .......................................................... 18

Chip Erase Command Sequence ........................................... 18

Sector Erase Command Sequence ........................................ 18

Figure 9. I

Current vs. Time (Showing Active and Automatic

CC1

Sleep Currents).............................................................................. 28

Figure 10. Typical I vs. Frequency ........................................... 28

CC1

Test Conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Figure 11. Test Setup..................................................................... 29

Table 8. Test Specifications ........................................................... 29

Table 9. Key to Switching Waveforms ........................................... 29

Figure 12. Input Waveforms and Measurement Levels ................. 29

AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 30

Table 10. Read Operations ............................................................ 30

Figure 13. Read Operations Timings ............................................. 30

Table 11. Hardware Reset (RESET#) ............................................ 31

Figure 14. RESET# Timings .......................................................... 31

Table 12. Word/Byte Configuration (BYTE#) ................................. 32

Figure 15. BYTE# Timings for Read Operations............................ 32

Figure 16. BYTE# Timings for Write Operations............................ 32

Table 13. Erase/Program Operations ............................................ 33

Figure 17. Program Operation Timings.......................................... 34

Figure 18. Chip/Sector Erase Operation Timings .......................... 35

Figure 19. Data# Polling Timings (During Embedded Algorithms). 36

Figure 20. Toggle Bit Timings (During Embedded Algorithms)...... 36

Figure 21. DQ2 vs. DQ6................................................................. 37

Table 14. Temporary Sector Unprotect .......................................... 37

Figure 22. Temporary Sector Unprotect Timing Diagram .............. 37

Figure 23. Sector Protect/Unprotect Timing Diagram .................... 38

Table 15. Alternate CE# Controlled Erase/Program Operations .... 39

Figure 24. Alternate CE# Controlled Write Operation Timings ...... 40

Table 16. Erase and Programming Performance ........................... 40

Table 17. Latchup Characteristics .................................................. 41

Table 18. TSOP Pin Capacitance .................................................. 41

Table 19. Data Retention ............................................................... 41

Physical Dimensions . . . . . . . . . . . . . . . . . . . . . . 42

Erase Suspend/Erase Resume Commands ........................... 19

Figure 4. Erase Operation............................................................... 20

Table 5. Am29SL800D Command Definitions ................................20

Write Operation Status . . . . . . . . . . . . . . . . . . . . 21

DQ7: Data# Polling ................................................................. 21

Figure 5. Data# Polling Algorithm ................................................... 22

RY/BY#: Ready/Busy# ........................................................... 23

DQ6: Toggle Bit I .................................................................... 23

DQ2: Toggle Bit II ................................................................... 23

Reading Toggle Bits DQ6/DQ2 .............................................. 23

Figure 6. Toggle Bit Algorithm......................................................... 24

DQ5: Exceeded Timing Limits ................................................ 24

DQ3: Sector Erase Timer ....................................................... 24

TS 048–48-Pin Standard TSOP ............................................. 42

TSR048–48-Pin Reverse TSOP ............................................. 43

FBA048–48-Ball Fine-Pitch Ball Grid Array (FBGA)

6 x 8 mm package .................................................................. 44

FBC048 – 48-Ball Fine-Pitch Ball Grid Array (FBGA)

8 x 9 mm package .................................................................. 45

VBK 048 - 48 Ball Fine-Pitch Ball Grid Array (FBGA) ............. 46

8.15 x 6.15 mm ....................................................................... 46

Revision Summary . . . . . . . . . . . . . . . . . . . . . . . . 47

2

Am29SL800D

April 27, 2005

D a t a S h e e t

Product Selector Guide

Family Part Number

Am29SL800D

Speed Options

90 (Note 2)

30

100

120

50

150

65

Max access time, ns (t_ACC

)

100

35

Max CE# access time, ns (t_CE

)

Max OE# access time, ns (t_OE

)

Notes:

1. See “AC Characteristics” for full specifications.

2. _CCmin. = 1.7 V

V

April 27, 2005

Am29SL800D

3

D a t a S h e e t

Block Diagram

DQ0–DQ15 (A-1)

RY/BY#

V_CC

V_SS

Sector Switches

Erase Voltage

Generator

Input/Output

Buffers

RESET#

State

Control

WE#

BYTE#

Command

Register

PGM Voltage

Generator

Data

Latch

Chip Enable

Output Enable

Logic

STB

CE#

OE#

Y-Decoder

Y-Gating

STB

V_CCDetector

Timer

Cell Matrix

X-Decoder

A0–A18

4

Am29SL800D

April 27, 2005

D a t a S h e e t

Connection Diagrams

A15

A14

A13

A12

A11

A10

A9

A8

NC

1

2

3

4

5

6

7

8

48

47

46

45

44

43

42

41

40

39

38

37

36

35

34

33

32

31

30

29

28

27

26

25

A16

BYTE#

V_SS

DQ15/A-1

DQ7

DQ14

DQ6

DQ13

DQ5

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

DQ12

DQ4

V_CC

WE#

RESET#

NC

Standard TSOP

DQ11

DQ3

DQ10

DQ2

DQ9

DQ1

DQ8

DQ0

OE#

V_SS

CE#

A0

NC

RY/BY#

A18

A17

A7

A6

A5

A4

A3

A2

A1

1

2

3

4

5

6

7

8

A15

A14

A13

A12

A11

A10

A9

A8

NC

48

47

46

45

44

43

42

41

40

39

38

37

36

35

34

33

32

31

30

29

28

27

26

25

A16

BYTE#

V_SS

DQ15/A-1

DQ7

DQ14

DQ6

DQ13

DQ5

DQ12

DQ4

V_CC

DQ11

DQ3

DQ10

DQ2

DQ9

DQ1

DQ8

DQ0

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

WE#

RESET#

NC

Reverse TSOP

NC

RY/BY#

A18

A17

A7

A6

A5

A4

A3

A2

A1

OE#

V_SS

CE#

A0

April 27, 2005

Am29SL800D

5

D a t a S h e e t

Connection Diagrams

48-Ball FBGA

(Top View, Balls Facing Down)

A6

B6

C6

D6

E6

F6

G6

H6

A13

A12

A14

A15

A16

BYTE# DQ15/A-1 V_SS

A5

A9

B5

A8

C5

D5

E5

F5

G5

H5

A10

A11

DQ7

DQ14

DQ13

DQ6

A4

B4

C4

D4

E4

F4

G4

H4

WE# RESET#

NC

DQ5

DQ12

V_CC

DQ4

A3

B3

C3

D3

E3

F3

G3

H3

RY/BY#

NC

A18

NC

DQ2

DQ10

DQ11

DQ3

A2

A7

B2

C2

A6

D2

A5

E2

F2

G2

H2

A17

DQ0

DQ8

DQ9

DQ1

A1

A3

B1

A4

C1

A2

D1

A1

E1

A0

F1

G1

H1

CE#

OE#

V_SS

and/or data integrity may be compromised if the

package body is exposed to temperatures about 150°C

for prolonged periods of time.

Special Handling Instructions for FBGA

Packages

Special handling is required for Flash Memory products

in molded packages (TSOP and BGA). The package

6

Am29SL800D

April 27, 2005

D a t a S h e e t

Pin Configuration

Logic Symbol

A0–A18

= 19 addresses

19

A0–A18

DQ0–DQ14 = 15 data inputs/outputs

16 or 8

DQ0–DQ15

(A-1)

DQ15/A-1

=

DQ15 (data input/output, word mode),

A-1 (LSB address input, byte mode)

BYTE#

CE#

=

Selects 8-bit or 16-bit mode

Chip enable

CE#

OE#

Output enable

WE#

Write enable

RESET#

BYTE#

RESET#

RY/BY#

Hardware reset pin, active low

Ready/Busy# output

1.65–2.2 V single power supply

Device ground

RY/BY#

V

CC

SS

NC

Pin not connected internally

April 27, 2005

Am29SL800D

7

D a t a S h e e t

Ordering Information

Standard Products

AMD standard products are available in several packages and operating ranges. The order number (Valid Combi-

nation) is formed by a combination of the elements below.

Am29SL800D

T

-100

E

C

TEMPERATURE RANGE

C

D

I

=

Commercial (0°C to +70°C)

Commercial (0°C to +70°C) with Pb-free package

^{Industrial (–40}°C to +85°C)

^{Industrial (–40}°C to +85°C) with Pb-free package

F

PACKAGE TYPE

E

=

48-Pin Thin Small Outline Package (TSOP)

Standard Pinout (TS 048)

F

48-Pin Thin Small Outline Package (TSOP)

Reverse Pinout (TSR048)

VU

48-ball Fine-Pitch Ball Grid Array (FBGA)

0.80mm pitch, 8.15 x 6.15mm package (VBK048)

WA

WC

=

48-Ball Fine-Pitch Ball Grid Array (FBGA)

0.80 mm pitch, 6 x 8 mm package (FBA048)

48-Ball Fine-Pitch Ball Grid Array (FBGA)

0.80 mm pitch, 8 x 9 mm package (FBC048)

SPEED OPTION

See Product Selector Guide and Valid Combinations

BOOT CODE SECTOR ARCHITECTURE

T

B

=

Top Sector

Bottom Sector

DEVICE NUMBER/DESCRIPTION

Am29SL800D

8 Megabit (1 M x 8-Bit/512 K x 16-Bit) CMOS Flash Memory

1.8 Volt-only Read, Program, and Erase

Valid Combinations

Valid Combinations list configurations planned to be supported in

volume for this device. Consult the local AMD sales office to confirm

availability of specific valid combinations and to check on newly

released combinations.

8

Am29SL800D

April 27, 2005

D a t a S h e e t

Valid Combinations for TSOP Packages

AM29SL800DT90,

AM29SL800DB90

AM29SL800DT100,

AM29SL800DB100

EC, EI, FC, FI, ED, EF

AM29SL800DT120,

AM29SL800DB120

AM29SL800DT150,

AM29SL800DB150

Valid Combinations for FBGA Packages

Order Number Package Marking

WAC,

WAD

WAI,

WAF

A800DT90U,

A800DB90U

AM29SL800DT90,

AM29SL800DB90

WCC,

WCD, A800DT90P,

WCI,

WCF

A800DB90P

WAC,

WAD

WAI,

WAF

A800DT10U,

A800DB10U

AM29SL800DT100,

AM29SL800DB100

WCC,

WCD, A800DT10P,

WCI,

WCF

A800DB10P

WAC,

WAD

WAI,

WAF

C, I,

D, F

A800DT12U,

A800DB12U

AM29SL800DT120,

AM29SL800DB120

WCC,

WCD, A800DT12P,

WCI,

WCF

A800DB12P

WAC,

WAD

WAI,

WAF

A800DT15U,

A800DB15U

AM29SL800DT150,

AM29SL800DB150

WCC,

WCD, A800DT15P,

WCI,

WCF

A800DB15P

A800DT12V

A800DB12V

Am29SL800DT120

VUF

April 27, 2005

Am29SL800D

9

D a t a S h e e t

tion needed to execute the command. The contents of

Device Bus Operations

the register serve as inputs to the internal state

machine. The state machine outputs dictate the func-

tion of the device. Table 1 lists the device bus

operations, the inputs and control levels they require,

and the resulting output. The following subsections

describe each of these operations in further detail.

This section describes the requirements and use of the

device bus operations, which are initiated through the

internal command register. The command register

itself does not occupy any addressable memory loca-

tion. The register is composed of latches that store the

commands, along with the address and data informa-

Table 1. Am29SL800D Device Bus Operations

DQ8–DQ15

BYTE#

Addresses

(Note 1)

DQ0–

DQ7

BYTE#

= V_IH

Operation

CE#

L

OE# WE# RESET#

= V_IL

Read

Write

L

H

L

H

A_IN

D_OUT

D_IN

D_OUT

D_IN

DQ8–DQ14 = High-Z,

DQ15 = A-1

L

H

V_CC

0.2 V

±

V_CC±

0.2 V

Standby

X

High-Z

Output Disable

Reset

L

H

X

H

X

H

L

X

High-Z

X

Sector Address, A6 =

L, A1 = H,

Sector Protect (Note)

L

H

L

V_ID

D_IN

X

A0 = L

Sector Address, A6 =

H, A1 = H,

Sector Unprotect (Note)

L

H

X

L

V_ID

D_IN

X

A0 = L

Temporary Sector Unprotect

X

A_IN

D_IN

High-Z

Legend:

L = Logic Low = V_IL, H = Logic High = V_IH, V_ID= 10 ± ±1.0 V, X = Don’t Care, A_IN= Address In, D_IN= Data In, D_OUT= Data Out

Notes:

1. Addresses are A18:A0 in word mode (BYTE# = V_IH), A18:A-1 in byte mode (BYTE# = V_IL).

The sector protect and sector unprotect functions may also be implemented via programming equipment.

ensures that no spurious alteration of the memory

Word/Byte Configuration

content occurs during the power transition. No

The BYTE# pin controls whether the device data I/O

command is necessary in this mode to obtain array

pins DQ15–DQ0 operate in the byte or word configura-

data. Standard microprocessor read cycles that assert

tion. If the BYTE# pin is set at logic ‘1’, the device is in

valid addresses on the device address inputs produce

word configuration, DQ15–DQ0 are active and con-

valid data on the device data outputs. The device

trolled by CE# and OE#.

remains enabled for read access until the command

If the BYTE# pin is set at logic ‘0’, the device is in byte

configuration, and only data I/O pins DQ0–DQ7 are

active and controlled by CE# and OE#. The data I/O

pins DQ8–DQ14 are tri-stated, and the DQ15 pin is

used as an input for the LSB (A-1) address function.

register contents are altered.

See Reading Array Data‚ on page 16 for more informa-

tion. Refer to the AC Read Operations table for timing

specifications and to Figure 13, on page 30 for the

timing diagram. I

in the DC Characteristics table

CC1

represents the active current specification for reading

array data.

Requirements for Reading Array Data

To read array data from the outputs, the system must

drive the CE# and OE# pins to V . CE# is the power

control and selects the device. OE# is the output

control and gates array data to the output pins. WE#

Writing Commands/Command Sequences

IL

To write a command or command sequence (which

includes programming data to the device and erasing

sectors of memory), the system must drive WE# and

should remain at V . The BYTE# pin determines

IH

whether the device outputs array data in words or

bytes.

CE# to V , and OE# to V .

IL

IH

For program operations, the BYTE# pin determines

whether the device accepts program data in bytes or

The internal state machine is set for reading array data

upon device power-up, or after a hardware reset. This

10

Am29SL800D

April 27, 2005

D a t a S h e e t

words. Refer to Word/Byte Configuration‚ on page 10

The device also enters the standby mode when the

RESET# pin is driven low. Refer to the next section,

RESET#: Hardware Reset Pin.

for more information.

The device features an Unlock Bypass mode to facili-

tate faster programming. Once the device enters the

Unlock Bypass mode, only two write cycles are

required to program a word or byte, instead of four. The

Word/Byte Program Command Sequence‚ on page 17

has details on programming data to the device using

both standard and Unlock Bypass command

sequences.

If the device is deselected during erasure or program-

ming, the device draws active current until the

operation is completed.

I

in Table 7 on page 27 represents the standby

CC3

current specification.

Automatic Sleep Mode

An erase operation can erase one sector, multiple sec-

tors, or the entire device. Tables 2 and 3 indicate the

address space that each sector occupies. A “sector

address” consists of the address bits required to

uniquely select a sector. The Command Definitions‚ on

page 16 has details on erasing a sector or the entire

chip, or suspending/resuming the erase operation.

The automatic sleep mode minimizes Flash device

energy consumption. The device automatically enables

this mode when addresses remain stable for t

+ 50

ACC

ns. The automatic sleep mode is independent of the

CE#, WE#, and OE# control signals. Standard address

access timings provide new data when addresses are

changed. While in sleep mode, output data is latched

and always available to the system. I

page 27 represents the automatic sleep mode current

specification.

in Table 7 on

After the system writes the autoselect command

sequence, the device enters the autoselect mode. The

system can then read autoselect codes from the

internal register (which is separate from the memory

array) on DQ7–DQ0. Standard read cycle timings apply

in this mode. Refer to the Autoselect Mode‚ on page 14

and Autoselect Command Sequence‚ on page 17 sec-

tions for more information.

CC4

RESET#: Hardware Reset Pin

The RESET# pin provides a hardware method of reset-

ting the device to reading array data. When the

RESET# pin is driven low for at least a period of t , the

RP

device immediately terminates any operation in

progress, tristates all output pins, and ignores all

read/write commands for the duration of the RESET#

pulse. The device also resets the internal state

machine to reading array data. The operation that was

interrupted should be reinitiated once the device is

ready to accept another command sequence, to

ensure data integrity.

I

in the DC Characteristics table represents the

CC2

active current specification for the write mode. AC

Characteristics‚ on page 30 contains timing specifica-

tion tables and timing diagrams for write operations.

Program and Erase Operation Status

During an erase or program operation, the system may

check the status of the operation by reading the status

bits on DQ7–DQ0. Standard read cycle timings and I

read specifications apply. Refer to Write Operation

Status‚ on page 21 for more information, and to “AC

Characteristics” for timing diagrams.

Current is reduced for the duration of the RESET#

CC

pulse. When RESET# is held at V ±0.2 V, the device

SS

draws CMOS standby current (I

). If RESET# is held

CC4

at V but not within V ±0.2 V, the standby current is

IL

SS

greater.

Standby Mode

The RESET# pin may be tied to the system reset cir-

cuitry. A system reset would thus also reset the Flash

memory, enabling the system to read the boot-up firm-

ware from the Flash memory.

When the system is not reading or writing to the device,

it can place the device in the standby mode. In this

mode, current consumption is greatly reduced, and the

outputs are placed in the high impedance state, inde-

pendent of the OE# input.

If RESET# is asserted during a program or erase oper-

ation, the RY/BY# pin remains a “0” (busy) until the

internal reset operation is complete, which requires a

The device enters the CMOS standby mode when the

CE# and RESET# pins are both held at V_CC± 0.2 V.

(Note that this is a more restricted voltage range than

time of t

(during Embedded Algorithms). The

READY

system can thus monitor RY/BY# to determine whether

the reset operation is complete. If RESET# is asserted

when a program or erase operation is not executing

(RY/BY# pin is “1”), the reset operation is completed

V .) If CE# and RESET# are held at V , but not within

IH

V

_CC± 0.2 V, the device will be in the standby mode, but

the standby current will be greater. The device requires

standard access time (t ) for read access when the

within a time of t

(not during Embedded Algo-

CE

READY

device is in either of these standby modes, before it is

ready to read data.

rithms). The system can read data t

after the

RH

RESET# pin returns to V .

IH

April 27, 2005

Am29SL800D

11

D a t a S h e e t

Refer to the Table 10 on page 30 for RESET# parame-

Output Disable Mode

ters and to Figure 14, on page 31 for the timing

diagram.

When the OE# input is at V , output from the device is

disabled. The output pins are placed in the high imped-

ance state.

IH

Table 2. Am29SL800DT Top Boot Block Sector Address Table

Address Range (in hexadecimal)

Sector Size

(Kbytes/

(x8)

(x16)

Sector

SA0

A18

0

A17

0

A16

0

A15

0

A14

X

0

A13

X

0

A12

X

0

Kwords)

Address Range

64/32

32/16

8/4

00000h–0FFFFh

10000h–1FFFFh

20000h–2FFFFh

30000h–3FFFFh

40000h–4FFFFh

50000h–5FFFFh

60000h–6FFFFh

70000h–7FFFFh

80000h–8FFFFh

90000h–9FFFFh

A0000h–AFFFFh

B0000h–BFFFFh

C0000h–CFFFFh

D0000h–DFFFFh

E0000h–EFFFFh

F0000h–F7FFFh

F8000h–F9FFFh

FA000h–FBFFFh

FC000h–FFFFFh

00000h–07FFFh

08000h–0FFFFh

10000h–17FFFh

18000h–1FFFFh

20000h–27FFFh

28000h–2FFFFh

30000h–37FFFh

38000h–3FFFFh

40000h–47FFFh

48000h–4FFFFh

50000h–57FFFh

58000h–5FFFFh

60000h–67FFFh

68000h–6FFFFh

70000h–77FFFh

78000h–7BFFFh

7C000h–7CFFFh

7D000h–7DFFFh

7E000h–7FFFFh

SA1

0

1

SA2

0

1

0

SA3

0

1

SA4

0

1

0

SA5

0

1

0

1

SA6

0

1

0

SA7

0

1

SA8

1

0

SA9

1

0

1

SA10

SA11

SA12

SA13

SA14

SA15

SA16

SA17

SA18

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

8/4

1

X

16/8

12

Am29SL800D

April 27, 2005

D a t a S h e e t

Table 3. Am29SL800DB Bottom Boot Block Sector Address Table

Address Range (in hexadecimal)

Sector Size

(Kbytes/

(x8)

(x16)

Sector

SA0

A18

0

A17

0

A16

0

A15

0

A14

0

A13

0

A12

X

0

Kwords)

Address Range

16/8

8/4

00000h–03FFFh

04000h–05FFFh

06000h–07FFFh

08000h–0FFFFh

10000h–1FFFFh

20000h–2FFFFh

30000h–3FFFFh

40000h–4FFFFh

50000h–5FFFFh

60000h–6FFFFh

70000h–7FFFFh

80000h–8FFFFh

90000h–9FFFFh

A0000h–AFFFFh

B0000h–BFFFFh

C0000h–CFFFFh

D0000h–DFFFFh

E0000h–EFFFFh

F0000h–FFFFFh

00000h–01FFFh

02000h–02FFFh

03000h–03FFFh

04000h–07FFFh

08000h–0FFFFh

10000h–17FFFh

18000h–1FFFFh

20000h–27FFFh

28000h–2FFFFh

30000h–37FFFh

38000h–3FFFFh

40000h–47FFFh

48000h–4FFFFh

50000h–57FFFh

58000h–5FFFFh

60000h–67FFFh

68000h–6FFFFh

70000h–77FFFh

78000h–7FFFFh

SA1

0

1

SA2

0

1

8/4

SA3

0

1

X

32/16

64/32

SA4

0

1

X

SA5

0

1

0

SA6

0

1

SA7

0

1

0

SA8

0

1

0

1

SA9

0

1

0

SA10

SA11

SA12

SA13

SA14

SA15

SA16

SA17

SA18

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

Note for Tables 2 and 3: Address range is A18:A-1 in byte mode and A18:A0 in word mode. See “Word/Byte Configuration” section for more

information.

April 27, 2005

Am29SL800D

13

D a t a S h e e t

address must appear on the appropriate highest order

Autoselect Mode

address bits (see Table 2 on page 12 and Table 3 on

page 13). Table 4 shows the remaining address bits

that are don’t care. When all necessary bits have been

set as required, the programming equipment may then

read the corresponding identifier code on DQ7–DQ0.

The autoselect mode provides manufacturer and

device identification, and sector protection verification,

through identifier codes output on DQ7–DQ0. This

mode is primarily intended for programming equipment

to automatically match a device to be programmed with

its corresponding programming algorithm. However,

the autoselect codes can also be accessed in-system

through the command register.

To access the autoselect codes in-system, the host

system can issue the autoselect command via the

command register, as shown in Table 5 on page 20.

This method does not require VID. See Command

Definitions‚ on page 16 for details on using the autose-

lect mode.

When using programming equipment, the autoselect

mode requires VID on address pin A9. Address pins

A6, A1, and A0 must be as shown in Table 4. In addi-

tion, when verifying sector protection, the sector

Table 4. Am29SL800D Autoselect Code (High Voltage Method)

A18 A11

to to

WE# A12 A10

A8

to

A7

A5

to

A2

DQ8

to

DQ15

DQ7

to

DQ0

Description

Mode

CE#

L

OE#

A9

A6

A1

A0

Manufacturer ID: AMD

L

H

X

V_ID

X

L

X

L

X

01h

Device ID:

Am29SL800D

(Top Boot Block)

Word

L

22h

EAh

X

V_ID

X

L

X

L

H

Byte

Word

Byte

L

H

X

22h

X

EAh

6Bh

Device ID:

Am29SL800D

(Bottom Boot Block)

X

V_ID

X

6Bh

X

01h (protected)

Sector Protection Verification

L

H

SA

V_ID

L

H

L

00h

(unprotected)

X

L = Logic Low = V_IL, H = Logic High = V_IH, SA = Sector Address, X = Don’t care.

through AMD’s ExpressFlash™ Service. Contact an

AMD representative for details.

Sector Protection/Unprotection

The hardware sector protection feature disables both

program and erase operations in any sector. The hard-

ware sector unprotection feature re-enables both

program and erase operations in previously protected

sectors. Sector protection/unprotection can be imple-

mented via two methods.

It is possible to determine whether a sector is protected

or unprotected. See Autoselect Mode‚ on page 14 for

details.

Temporary Sector Unprotect

This feature allows temporary unprotection of previ-

ously protected sectors to change data in-system. The

Sector Unprotect mode is activated by setting the

Sector Protection/ Unprotection requires V on the

ID

RESET# pin only, and can be implemented either in-

system or via programming equipment. Figure 1, on

page 15 shows the algorithms and Figure 23, on page

38 shows the timing diagram. For sector unprotect, all

unprotected sectors must first be protected prior to the

first sector unprotect write cycle.

RESET# pin to V . During this mode, formerly pro-

ID

tected sectors can be programmed or erased by

selecting the sector addresses. Once V is removed

ID

from the RESET# pin, all the previously protected

sectors are protected again. Figure 2, on page 16

shows the algorithm, and Figure 22, on page 37 shows

the timing diagrams, for this feature.

The device is shipped with all sectors unprotected.

AMD offers the option of programming and protecting

sectors at its factory prior to shipping the device

14

Am29SL800D

April 27, 2005

D a t a S h e e t

START

Protect all sectors:

The indicated portion

of the sector protect

algorithm must be

performed for all

unprotected sectors

prior to issuing the

first sector

PLSCNT = 1

RESET# = V

ID

RESET# = V

ID

Wait 1 ms

unprotect address

No

First Write

Cycle = 60h?

First Write

Cycle = 60h?

Temporary Sector

Unprotect Mode

Temporary Sector

Unprotect Mode

Yes

Set up sector

address

No

All sectors

protected?

Sector Protect:

Write 60h to sector

address with

A6 = 0, A1 = 1,

A0 = 0

Yes

Set up first sector

address

Sector Unprotect:

Wait 150 µs

Write 60h to sector

address with

A6 = 1, A1 = 1,

A0 = 0

Verify Sector

Protect: Write 40h

to sector address

with A6 = 0,

Reset

PLSCNT = 1

Increment

PLSCNT

Wait 15 ms

A1 = 1, A0 = 0

Verify Sector

Unprotect: Write

40h to sector

address with

A6 = 1, A1 = 1,

A0 = 0

Read from

sector address

with A6 = 0,

A1 = 1, A0 = 0

Increment

PLSCNT

No

PLSCNT

= 25?

Read from

sector address

with A6 = 1,

A1 = 1, A0 = 0

Data = 01h?

Yes

No

Yes

Set up

next sector

address

Yes

No

PLSCNT

= 1000?

Protect another

sector?

Data = 00h?

Yes

Device failed

No

Yes

Remove V

from RESET#

ID

No

Last sector

verified?

Device failed

Write reset

command

Yes

Remove V

from RESET#

ID

Sector Unprotect

Algorithm

Sector Protect

Algorithm

Sector Protect

complete

Write reset

command

Sector Unprotect

complete

Figure 1. In-System Sector Protect/Unprotect Algorithms

April 27, 2005

Am29SL800D

15

D a t a S h e e t

for command definitions). In addition, the following

hardware data protection measures prevent accidental

erasure or programming, which might otherwise be

START

caused by spurious system level signals during V

CC

power-up and power-down transitions, or from system

noise.

RESET# = V_ID

(Note 1)

Low V

Write Inhibit

CC

When V

is less than V

, the device does not

LKO

Perform Erase or

Program Operations

CC

accept any write cycles. This protects data during V

CC

power-up and power-down. The command register and

all internal program/erase circuits are disabled, and the

RESET# = V_IH

device resets. Subsequent writes are ignored until V

CC

is greater than V

. The system must provide the

LKO

proper signals to the control pins to prevent uninten-

tional writes when V is greater than V

.

CC

LKO

Temporary Sector

Unprotect Completed

(Note 2)

Write Pulse “Glitch” Protection

Noise pulses of less than 5 ns (typical) on OE#, CE# or

WE# do not initiate a write cycle.

Logical Inhibit

Notes:

Write cycles are inhibited by holding any one of OE# =

1. All protected sectors unprotected.

V , CE# = V or WE# = V . To initiate a write cycle,

IL

IH

2. All previously protected sectors are protected once again.

CE# and WE# must be a logical zero while OE# is a

logical one.

Power-Up Write Inhibit

Figure 2. Temporary Sector Unprotect Operation

If WE# = CE# = V and OE# = V during power up, the

IL

IH

Hardware Data Protection

device does not accept commands on the rising edge

of WE#. The internal state machine is automatically

reset to reading array data on power-up.

The command sequence requirement of unlock cycles

for programming or erasing provides data protection

against inadvertent writes (refer to Table 5 on page 20

After the device accepts an Erase Suspend command,

the device enters the Erase Suspend mode. The

system can read array data using the standard read

timings, except that if it reads at an address within

erase-suspended sectors, the device outputs status

data. After completing a programming operation in the

Erase Suspend mode, the system may once again

read array data with the same exception. See Erase

Suspend/Erase Resume Commands‚ on page 19 for

more information on this mode.

Command Definitions

Writing specific address and data commands or

sequences into the command register initiates device

operations. Table 5 on page 20 defines the valid reg-

ister command sequences. Writing incorrect address

and data values or writing them in the improper

sequence may place the device in an unknown state. A

reset command is then required to return the device to

reading array data.

All addresses are latched on the falling edge of WE# or

CE#, whichever happens later. All data is latched on

the rising edge of WE# or CE#, whichever happens

first. Refer to the appropriate timing diagrams in the

AC Characteristics‚ on page 30 section.

The system must issue the reset command to re-

enable the device for reading array data if DQ5 goes

high, or while in the autoselect mode. See Reset Com-

mand‚ on page 16.

See also Requirements for Reading Array Data‚ on

page 10 for more information. Table 10 on page 30 pro-

vides the read parameters, and Figure 12, on page 29

shows the timing diagram.

Reading Array Data

The device is automatically set to reading array data

after device power-up. No commands are required to

retrieve data. The device is also ready to read array

data after completing an Embedded Program or

Embedded Erase algorithm.

Reset Command

Writing the reset command to the device resets the

device to reading array data. Address bits are don’t

care for this command.

16

Am29SL800D

April 27, 2005

D a t a S h e e t

The reset command may be written between the

The program address and data are written next, which

in turn initiate the Embedded Program algorithm. The

system is not required to provide further controls or tim-

ings. The device automatically generates the program

pulses and verifies the programmed cell margin.

Table 5 on page 20 shows the address and data

requirements for the byte program command

sequence.

sequence cycles in an erase command sequence

before erasing begins. This resets the device to reading

array data. Once erasure begins, however, the device

ignores reset commands until the operation is

complete.

The reset command may be written between the

sequence cycles in a program command sequence

before programming begins. This resets the device to

reading array data (also applies to programming in

Erase Suspend mode). Once programming begins,

however, the device ignores reset commands until the

operation is complete.

When the Embedded Program algorithm is complete,

the device then returns to reading array data and

addresses are no longer latched. The system can

determine the status of the program operation by using

DQ7, DQ6, or RY/BY#. See Table on page 21 for infor-

mation on these status bits.

The reset command may be written between the

sequence cycles in an autoselect command sequence.

Once in the autoselect mode, the reset command must

be written to return to reading array data (also applies

to autoselect during Erase Suspend).

Any commands written to the device during the

Embedded Program Algorithm are ignored. Note that a

hardware reset immediately terminates the program-

ming operation. The Byte Program command

sequence should be reinitiated once the device has

reset to reading array data, to ensure data integrity.

If DQ5 goes high during a program or erase operation,

writing the reset command returns the device to

reading array data (also applies during Erase

Suspend).

Programming is allowed in any sequence and across

sector boundaries. A bit cannot be programmed

from a “0” back to a “1”. Attempting to do so may halt

the operation and set DQ5 to “1”, or cause the Data#

Polling algorithm to indicate the operation was suc-

cessful. However, a succeeding read will show that the

data is still “0”. Only erase operations can convert a “0”

to a “1”.

Autoselect Command Sequence

The autoselect command sequence allows the host

system to access the manufacturer and devices codes,

and determine whether or not a sector is protected.

Table 5 on page 20 shows the address and data

requirements. This method is an alternative to that

shown in Table 4 on page 14, which is intended for

Unlock Bypass Command Sequence

The unlock bypass feature allows the system to

program bytes or words to the device faster than using

the standard program command sequence. The unlock

bypass command sequence is initiated by first writing

two unlock cycles. This is followed by a third write cycle

containing the unlock bypass command, 20h. The

device then enters the unlock bypass mode. A two-

cycle unlock bypass program command sequence is all

that is required to program in this mode. The first cycle

in this sequence contains the unlock bypass program

command, A0h; the second cycle contains the program

address and data. Additional data is programmed in

the same manner. This mode dispenses with the initial

two unlock cycles required in the standard program

command sequence, resulting in faster total program-

ming time. Table 5 on page 20 shows the requirements

for the command sequence.

PROM programmers and requires V on address bit

A9.

ID

The autoselect command sequence is initiated by

writing two unlock cycles, followed by the autoselect

command. The device then enters the autoselect

mode, and the system may read at any address any

number of times, without initiating another command

sequence. A read cycle at address XX00h retrieves the

manufacturer code. A read cycle at address 01h in

word mode (or 02h in byte mode) returns the device

code. A read cycle containing a sector address (SA)

and the address 02h in word mode (or 04h in byte

mode) returns 01h if that sector is protected, or 00h if it

is unprotected. Refer to Table 2 on page 12 and Table 3

on page 13 for valid sector addresses.

The system must write the reset command to exit the

autoselect mode and return to reading array data.

During the unlock bypass mode, only the Unlock

Bypass Program and Unlock Bypass Reset commands

are valid. To exit the unlock bypass mode, the system

must issue the two-cycle unlock bypass reset

command sequence. The first cycle must contain the

data 90h; the second cycle the data 00h. Addresses

are don’t cares. The device then returns to reading

array data.

Word/Byte Program Command Sequence

The system may program the device by word or byte,

depending on the state of the BYTE# pin. Program-

ming is a four-bus-cycle operation. The program

command sequence is initiated by writing two unlock

write cycles, followed by the program set-up command.

April 27, 2005

Am29SL800D

17

D a t a S h e e t

Figure 3 illustrates the algorithm for the program oper-

ation. See Table 13 on page 33 for parameters, and to

Figure 17, on page 34 for timing diagrams.

Chip Erase Command Sequence

Chip erase is a six bus cycle operation. The chip erase

command sequence is initiated by writing two unlock

cycles, followed by a set-up command. Two additional

unlock write cycles are then followed by the chip erase

command, which in turn invokes the Embedded Erase

algorithm. The device does not require the system to

preprogram prior to erase. The Embedded Erase algo-

rithm automatically preprograms and verifies the entire

memory for an all zero data pattern prior to electrical

erase. The system is not required to provide any con-

trols or timings during these operations. Table 5 on

page 20 shows the address and data requirements for

the chip erase command sequence.

START

Write Program

Command Sequence

Data Poll

from System

Embedded

Program

algorithm

in progress

Any commands written to the chip during the

Embedded Erase algorithm are ignored. Note that a

hardware reset during the chip erase operation imme-

diately terminates the operation. The Chip Erase

command sequence should be reinitiated once the

device has returned to reading array data, to ensure

data integrity.

Verify Data?

No

Yes

The system can determine the status of the erase oper-

ation by using DQ7, DQ6, DQ2, or RY/BY#. See “Write

Operation Status” for information on these status bits.

When the Embedded Erase algorithm is complete, the

device returns to reading array data and addresses are

no longer latched.

No

Increment Address

Last Address?

Yes

Programming

Completed

Figure 4, on page 20 illustrates the algorithm for the

erase operation. See Table 13 on page 30 for parame-

ters, and to Figure 10, on page 28 for timing diagrams.

1. See Table 5 for program command sequence.

Sector Erase Command Sequence

Figure 3. Program Operation

Sector erase is a six bus cycle operation. The sector

erase command sequence is initiated by writing two

unlock cycles, followed by a set-up command. Two

additional unlock write cycles are then followed by the

address of the sector to be erased, and the sector

erase command. Table 5 shows the address and data

requirements for the sector erase command sequence.

The device does not require the system to preprogram

the memory prior to erase. The Embedded Erase algo-

rithm automatically programs and verifies the sector for

an all zero data pattern prior to electrical erase. The

system is not required to provide any controls or

timings during these operations.

After the command sequence is written, a sector erase

time-out of 50 µs begins. During the time-out period,

additional sector addresses and sector erase com-

mands may be written. Loading the sector erase buffer

may be done in any sequence, and the number of

sectors may be from one sector to all sectors. The time

between these additional cycles must be less than 50

µs, otherwise the last address and command might not

be accepted, and erasure may begin. It is recom-

mended that processor interrupts be disabled during

18

Am29SL800D

April 27, 2005

D a t a S h e e t

this time to ensure all commands are accepted. The

time-out period and suspends the erase operation.

Addresses are “don’t-cares” when writing the Erase

Suspend command.

interrupts can be re-enabled after the last Sector Erase

command is written. If the time between additional

sector erase commands can be assumed to be less

than 50 µs, the system need not monitor DQ3. Any

command other than Sector Erase or Erase

Suspend during the time-out period resets the

device to reading array data. The system must

rewrite the command sequence and any additional

sector addresses and commands.

When the Erase Suspend command is written during a

sector erase operation, the device requires a maximum

of 20 µs to suspend the erase operation. However,

when the Erase Suspend command is written during

the sector erase time-out, the device immediately ter-

minates the time-out period and suspends the erase

operation.

The system can monitor DQ3 to determine if the sector

erase timer has timed out. (See DQ3: Sector Erase

Timer‚ on page 24.) The time-out begins from the rising

edge of the final WE# pulse in the command sequence.

After the erase operation has been suspended, the

system can read array data from or program data to

any sector not selected for erasure. (The device “erase

suspends” all sectors selected for erasure.) Normal

read and write timings and command definitions apply.

Reading at any address within erase-suspended

sectors produces status data on DQ7–DQ0. The

system can use DQ7, or DQ6 and DQ2 together, to

determine if a sector is actively erasing or is erase-sus-

pended. See Write Operation Status‚ on page 21 for

information on these status bits.

Once the sector erase operation has begun, only the

Erase Suspend command is valid. All other commands

are ignored. Note that a hardware reset during the

sector erase operation immediately terminates the

operation. The Sector Erase command sequence

should be reinitiated once the device has returned to

reading array data, to ensure data integrity.

When the Embedded Erase algorithm is complete, the

device returns to reading array data and addresses are

no longer latched. The system can determine the

status of the erase operation by using DQ7, DQ6, DQ2,

or RY/BY#. (Refer to Write Operation Status‚ on

page 21 for information on these status bits.)

After an erase-suspended program operation is com-

plete, the system can once again read array data within

non-suspended sectors. The system can determine

the status of the program operation using the DQ7 or

DQ6 status bits, just as in the standard program oper-

ation. See Write Operation Status‚ on page 21 for

more information.

Figure 4, on page 20 illustrates the algorithm for the

erase operation. Refer to the Table 16 on page 40for

parameters, and to Figure 18, on page 35 for timing

diagrams.

The system may also write the autoselect command

sequence when the device is in the Erase Suspend

mode. The device allows reading autoselect codes

even at addresses within erasing sectors, since the

codes are not stored in the memory array. When the

device exits the autoselect mode, the device reverts to

the Erase Suspend mode, and is ready for another

valid operation. See Autoselect Command Sequence‚

on page 17 for more information.

Erase Suspend/Erase Resume Commands

The Erase Suspend command allows the system to

interrupt a sector erase operation and then read data

from, or program data to, any sector not selected for

erasure. This command is valid only during the sector

erase operation, including the 50 µs time-out period

during the sector erase command sequence. The

Erase Suspend command is ignored if written during

the chip erase operation or Embedded Program algo-

rithm. Writing the Erase Suspend command during the

Sector Erase time-out immediately terminates the

The system must write the Erase Resume command

(address bits are don’t care) to exit the erase suspend

mode and continue the sector erase operation. Further

writes of the Resume command are ignored. Another

Erase Suspend command can be written after the

device has resumed erasing.

April 27, 2005

Am29SL800D

19

D a t a S h e e t

START

Write Erase

Command Sequence

Data Poll

from System

Embedded

Erase

algorithm

in progress

No

Data = FFh?

Yes

Erasure Completed

Notes:

1. See Table 5 for erase command sequence.

2. See “DQ3: Sector Erase Timer” for more information.

Figure 4. Erase Operation

Table 5. Am29SL800D Command Definitions (Sheet 1 of 2)

Bus Cycles (Notes 2-5)

Third Fourth

Addr Data Addr Data Addr Data Addr Data

Command

Sequence

(Note 1)

First

Second

Fifth

Sixth

Addr Data Addr Data

Read (Note 6)

Reset (Note 7)

1

RA

XXX

555

AAA

555

AAA

555

AAA

RD

F0

Word

Byte

Word

Byte

Word

Byte

2AA

555

2AA

555

2AA

555

AAA

555

Manufacturer ID

4

AA

55

90

X00

01

X01

X02

X01

X02

22EA

EA

Device ID,

Top Boot Block

AAA

555

226B

6B

Device ID,

Bottom Boot Block

AAA

XX00

XX01

00

(SA)

X02

Word

Byte

Word

Byte

555

AAA

555

2AA

555

2AA

555

AAA

555

Sector Protect Verify

(Note 9)

4

AA

55

90

(SA)

X04

01

TBD

X03

X04

PA

Extension

AAA

Word

Byte

Word

Byte

555

AAA

555

2AA

555

2AA

555

AAA

555

Program

4

3

AA

55

A0

20

PD

Unlock Bypass

20

AAA

Am29SL800D

April 27, 2005

D a t a S h e e t

Table 5. Am29SL800D Command Definitions (Sheet 2 of 2)

Bus Cycles (Notes 2-5)

Command

Sequence

(Note 1)

First

Second

Third

Addr

Fourth

Fifth

Sixth

Addr Data Addr Data

Data Addr Data Addr Data Addr Data

Unlock Bypass Program (Note 10)

Unlock Bypass Reset (Note 11)

2

XXX

555

A0

90

PA

PD

00

XXX

2AA

555

2AA

555

Word

555

AAA

555

AAA

555

2AA

555

2AA

555

Chip Erase

6

AA

55

80

AA

55

10

30

Byte

Word

Byte

AAA

555

AAA

Sector Erase

SA

AAA

XXX

AAA

Erase Suspend (Note 12)

Erase Resume (Note 13)

1

B0

30

Legend:

X = Don’t care

RA = Address of the memory location to be read.

RD = Data read from location RA during read operation.

PA = Address of the memory location to be programmed. Addresses latch on the falling edge of the WE# or CE# pulse, whichever

happens later.

PD = Data to be programmed at location PA. Data latches on the rising edge of WE# or CE# pulse, whichever happens first.

SA = Address of the sector to be verified (in autoselect mode) or erased. Address bits A18–A12 uniquely select any sector.

Notes:

1. See Table 1 for description of bus operations.

DQ7: Data# Polling

2. All values are in hexadecimal.

The Data# Polling bit, DQ7, indicates to the host

system whether an Embedded Algorithm is in progress

3. Except when reading array or autoselect data, all bus cycles are

write operations.

or completed, or whether the device is in Erase Sus-

4. Data bits DQ15–DQ8 are don’t cares for unlock and command

pend. Data# Polling is valid after the rising edge of the

final WE# pulse in the program or erase command

sequence.

cycles.

5. Address bits A18–A11 are don’t cares for unlock and command

cycles, unless SA or PA required.

6. No unlock or command cycles required when reading array data,

unless SA or PA required.

During the Embedded Program algorithm, the device

outputs on DQ7 the complement of the datum pro-

grammed to DQ7. This DQ7 status also applies to

programming during Erase Suspend. When the

Embedded Program algorithm is complete, the device

outputs the datum programmed to DQ7. The system

must provide the program address to read valid status

information on DQ7. If a program address falls within a

protected sector, Data# Polling on DQ7 is active for

approximately 1 µs, then the device returns to reading

array data.

7. The Reset command is required to return to reading array data

when device is in the autoselect mode, or if DQ5 goes high (while

the device is providing status data).

8. The fourth cycle of the autoselect command sequence is a read

cycle.

9. The data is 00h for an unprotected sector and 01h for a protected

sector. See “Autoselect Command Sequence” for more

information.

10. The Unlock Bypass command is required prior to the Unlock

Bypass Program command.

11. The Unlock Bypass Reset command is required to return to

reading array data when the device is in the unlock bypass mode.

During the Embedded Erase algorithm, Data# Polling

produces a 0 on DQ7. When the Embedded Erase

algorithm is complete, or if the device enters the Erase

Suspend mode, Data# Polling produces a 1 on DQ7.

This is analogous to the complement/true datum output

described for the Embedded Program algorithm: the

erase function changes all the bits in a sector to 1; prior

to this, the device outputs the complement, or 0. The

system must provide an address within any of the

sectors selected for erasure to read valid status infor-

mation on DQ7.

12. The system may read and program in non-erasing sectors, or enter the

autoselect mode, when in the Erase Suspend mode. The Erase Suspend

command is valid only during a sector erase operation.

13. The Erase Resume command is valid only during the Erase Suspend

mode.

Write Operation Status

The device provides several bits to determine the

status of a write operation: DQ2, DQ3, DQ5, DQ6,

DQ7, and RY/BY#. Table 6 and the following subsec-

tions describe the functions of these bits. DQ7,

RY/BY#, and DQ6 each offer a method for determining

whether a program or erase operation is complete or in

progress. These three bits are discussed first.

After an erase command sequence is written, if all

sectors selected for erasing are protected, Data#

Polling on DQ7 is active for approximately 100 µs, then

the device returns to reading array data. If not all

selected sectors are protected, the Embedded Erase

April 27, 2005

Am29SL800D

21

D a t a S h e e t

algorithm erases the unprotected sectors, and ignores

the selected sectors that are protected.

START

When the system detects DQ7 has changed from the

complement to true data, it can read valid data at DQ7–

DQ0 on the following read cycles. This is because DQ7

may change asynchronously with DQ0–DQ6 while

Output Enable (OE#) is asserted low. Figure 19, on

page 36, Data# Polling Timings (During Embedded

Algorithms), illustrates this.

Read DQ7–DQ0

Addr = VA

Table 6 on page 25 shows the outputs for Data# Polling

on DQ7. Figure 5 shows the Data# Polling algorithm.

Yes

DQ7 = Data?

No

DQ5 = 1?

Yes

Read DQ7–DQ0

Addr = VA

Yes

DQ7 = Data?

No

PASS

FAIL

Notes:

1. VA = Valid address for programming. During a sector erase

operation, a valid address is an address within any sector

selected for erasure. During chip erase, a valid address is any

non-protected sector address.

2. DQ7 should be rechecked even if DQ5 = “1” because DQ7 may

change simultaneously with DQ5.

Figure 5. Data# Polling Algorithm

22

Am29SL800D

April 27, 2005

D a t a S h e e t

Table 6 on page 25 shows the outputs for Toggle Bit I

RY/BY#: Ready/Busy#

on DQ6. Figure 6, on page 24 shows the toggle bit

algorithm. Figure 20, on page 36 shows the toggle bit

timing diagrams. Figure 21, on page 37 shows the dif-

ferences between DQ2 and DQ6 in graphical form. See

also the subsection on DQ2: Toggle Bit II.

The RY/BY# is a dedicated, open-drain output pin that

indicates whether an Embedded Algorithm is in

progress or complete. The RY/BY# status is valid after

the rising edge of the final WE# pulse in the command

sequence. Since RY/BY# is an open-drain output,

several RY/BY# pins can be tied together in parallel

DQ2: Toggle Bit II

with a pull-up resistor to V

.

CC

The Toggle Bit II on DQ2, when used with DQ6, indi-

cates whether a particular sector is actively erasing

(that is, the Embedded Erase algorithm is in progress),

or whether that sector is erase-suspended. Toggle Bit

II is valid after the rising edge of the final WE# pulse in

the command sequence. The device toggles DQ2 with

each OE# or CE# read cycle.

If the output is low (Busy), the device is actively erasing

or programming. (This includes programming in the

Erase Suspend mode.) If the output is high (Ready),

the device is ready to read array data (including during

the Erase Suspend mode), or is in the standby mode.

Table 6 on page 25 shows the outputs for RY/BY#.

Figure 14, on page 31, Figure 17, on page 34, and

Figure 18, on page 35 shows RY/BY# for reset, pro-

gram, and erase operations, respectively.

DQ2 toggles when the system reads at addresses

within those sectors that have been selected for era-

sure. But DQ2 cannot distinguish whether the sector is

actively erasing or is erase-suspended. DQ6, by com-

parison, indicates whether the device is actively

erasing, or is in Erase Suspend, but cannot distinguish

which sectors are selected for erasure. Thus, both

status bits are required for sector and mode informa-

tion. Refer to Table 6 on page 25 to compare outputs

for DQ2 and DQ6.

DQ6: Toggle Bit I

Toggle Bit I on DQ6 indicates whether an Embedded

Program or Erase algorithm is in progress or complete,

or whether the device has entered the Erase Suspend

mode. Toggle Bit I may be read at any address, and is

valid after the rising edge of the final WE# pulse in the

command sequence (prior to the program or erase

operation), and during the sector erase time-out.

Figure 6, on page 24 shows the toggle bit algorithm in

flowchart form, and the section DQ2: Toggle Bit II

explains the algorithm. See also the DQ6: Toggle Bit I

subsection. Figure 20, on page 36 shows the toggle bit

timing diagram. Figure 21, on page 37 shows the differ-

ences between DQ2 and DQ6 in graphical form.

During an Embedded Program or Erase algorithm

operation, successive read cycles to any address

cause DQ6 to toggle (The system may use either OE#

or CE# to control the read cycles). When the operation

is complete, DQ6 stops toggling.

Reading Toggle Bits DQ6/DQ2

After an erase command sequence is written, if all

sectors selected for erasing are protected, DQ6 toggles

for approximately 100 µs, then returns to reading array

data. If not all selected sectors are protected, the

Embedded Erase algorithm erases the unprotected

sectors, and ignores the selected sectors that are

protected.

Refer to Figure 6, on page 24 for the following discus-

sion. Whenever the system initially begins reading

toggle bit status, it must read DQ7–DQ0 at least twice

in a row to determine whether a toggle bit is toggling.

Typically, the system would note and store the value of

the toggle bit after the first read. After the second read,

the system would compare the new value of the toggle

bit with the first. If the toggle bit is not toggling, the

device has completed the program or erase operation.

The system can read array data on DQ7–DQ0 on the

following read cycle.

The system can use DQ6 and DQ2 together to deter-

mine whether a sector is actively erasing or is erase-

suspended. When the device is actively erasing (that is,

the Embedded Erase algorithm is in progress), DQ6

toggles. When the device enters the Erase Suspend

mode, DQ6 stops toggling. However, the system must

also use DQ2 to determine which sectors are erasing

or erase-suspended. Alternatively, the system can use

DQ7 (see the subsection on DQ7: Data# Polling).

However, if after the initial two read cycles, the system

determines that the toggle bit is still toggling, the

system also should note whether the value of DQ5 is

high (see the section on DQ5). If it is, the system

should then determine again whether the toggle bit is

toggling, since the toggle bit may have stopped tog-

gling just as DQ5 went high. If the toggle bit is no longer

toggling, the device has successfully completed the

program or erase operation. If it is still toggling, the

device did not completed the operation successfully,

and the system must write the reset command to return

to reading array data.

If a program address falls within a protected sector,

DQ6 toggles for approximately 1 µs after the program

command sequence is written, then returns to reading

array data.

DQ6 also toggles during the erase-suspend-program

mode, and stops toggling once the Embedded

Program algorithm is complete.

April 27, 2005

Am29SL800D

23

D a t a S h e e t

The remaining scenario is that the system initially

condition that indicates the program or erase cycle was

not successfully completed.

determines that the toggle bit is toggling and DQ5 has

not gone high. The system may continue to monitor the

toggle bit and DQ5 through successive read cycles,

determining the status as described in the previous

paragraph. Alternatively, it may choose to perform

other system tasks. In this case, the system must start

at the beginning of the algorithm when it returns to

determine the status of the operation (top of Figure 6).

The DQ5 failure condition may appear if the system

tries to program a 1 to a location that is previously pro-

grammed to 0. Only an erase operation can change

a 0 back to a 1. Under this condition, the device halts

the operation, and when the operation has exceeded

the timing limits, DQ5 produces a 1.

Under both these conditions, the system must issue the

reset command to return the device to reading array

data.

START

Read DQ7–DQ0

DQ3: Sector Erase Timer

After writing a sector erase command sequence, the

system may read DQ3 to determine whether or not an

erase operation has begun. (The sector erase timer

does not apply to the chip erase command.) If addi-

tional sectors are selected for erasure, the entire time-

out also applies after each additional sector erase com-

mand. When the time-out is complete, DQ3 switches

from 0 to 1. If the time between additional sector erase

commands from the system can be assumed to be less

than 50 µs, the system need not monitor DQ3. See also

Sector Erase Command Sequence‚ on page 18.

Read DQ7–DQ0

No

Toggle Bit

= Toggle?

Yes

No

DQ5 = 1?

Yes

After the sector erase command sequence is written,

the system should read the status on DQ7 (Data#

Polling) or DQ6 (Toggle Bit I) to ensure the device has

accepted the command sequence, and then read DQ3.

If DQ3 is 1, the internally controlled erase cycle has

begun; all further commands (other than Erase Sus-

pend) are ignored until the erase operation is complete.

If DQ3 is 0, the device will accept additional sector

erase commands. To ensure the command has been

accepted, the system software should check the status

of DQ3 prior to and following each subsequent sector

erase command. If DQ3 is high on the second status

check, the last command might not have been

accepted. Figure 6 shows the outputs for DQ3.

Read DQ7–DQ0

Twice

Toggle Bit

= Toggle?

No

Yes

Program/Erase

Operation Not

Complete, Write

Reset Command

Program/Erase

Operation Complete

Notes:

1. Read toggle bit twice to determine whether or not it is toggling.

See text.

2. Recheck toggle bit because it may stop toggling as DQ5 changes

to “1”. See text

Figure 6. Toggle Bit Algorithm

DQ5: Exceeded Timing Limits

DQ5 indicates whether the program or erase time has

exceeded a specified internal pulse count limit. Under

these conditions DQ5 produces a 1. This is a failure

24

Am29SL800D

April 27, 2005

D a t a S h e e t

Table 6. Write Operation Status

DQ7

DQ5

DQ2

Operation

(Note 2)

DQ6

(Note 1)

DQ3

N/A

1

(Note 2)

RY/BY#

Embedded Program Algorithm

Embedded Erase Algorithm

DQ7#

0

Toggle

0

No toggle

Toggle

0

Standard

Mode

Reading within Erase

Suspended Sector

1

No toggle

0

N/A

Toggle

1

Erase

Suspend

Mode

Reading within Non-Erase

Suspended Sector

Data

0

Data

N/A

Data

N/A

1

0

Erase-Suspend-Program

DQ7#

Toggle

Notes:

1. DQ5 switches to ‘1’ when an Embedded Program or Embedded Erase operation has exceeded the maximum timing limits. See “DQ5:

Exceeded Timing Limits for more information.

2. DQ7 and DQ2 require a valid address when reading status information. Refer to the appropriate subsection for further details.

April 27, 2005

Am29SL800D

25

D a t a S h e e t

Absolute Maximum Ratings

Storage Temperature

Plastic Packages...............................–65°C to +150°C

Ambient Temperature

with Power Applied............................–65°C to +125°C

Voltage with Respect to Ground

V

(Note 1)................................–0.5 V to +2.5 V

CC

A9, OE#,

and RESET# (Note 2)................–0.5 V to +11.0 V

All other pins (Note 1)........... –0.5 V to V +0.5 V

CC

Output Short Circuit Current (Note 3) ............. 100 mA

Notes:

1. Minimum DC voltage on input or I/O pins is –0.5 V. During voltage transitions, input or I/O pins may overshoot V_SSto –2.0 V for periods of

up to 20 ns. See Figure 7. Maximum DC voltage on input or I/O pins is V_CC+0.5 V. During voltage transitions, input or I/O pins may overshoot

to V_CC+2.0 V for periods up to 20 ns. See Figure 8.

2. Minimum DC input voltage on pins A9, OE#, and RESET# is –0.5 V. During voltage transitions, A9, OE#, and RESET# may overshoot V_SS

to –2.0 V for periods of up to 20 ns. See Maximum DC input voltage on pin A9 is +11.0 V which may overshoot to 12.5 V for periods up to

20 ns.

3. No more than one output may be shorted to ground at a time. Duration of the short circuit should not be greater than one second.

Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only;

functional operation of the device at these or any other conditions above those indicated in the operational sections of this data sheet is not

implied. Exposure of the device to absolute maximum rating conditions for extended periods may affect device reliability.

20 ns

V_CC

+2.0 V

0.0 V

V_CC

–0.5 V

–2.0 V

+0.5 V

2.0 V

20 ns

Figure 7. Maximum Negative

Figure 8. Maximum Positive Overshoot Waveform

Overshoot Waveform Maximum Negative Overshoot

Waveform

Operating Ranges

Commercial (C) Devices

Ambient Temperature (T ).......................0°C to +70°C

A

Industrial (I) Devices

Ambient Temperature (T )...................–40°C to +85°C

A

V

Supply Voltages

CC

, 90ns speed option ...................+1.70 V to +2.2 V

, All other speed options............+1.65 V to +2.2 V

Operating ranges define those limits between which the functionality of the device is guaranteed.

26

Am29SL800D

April 27, 2005

D a t a S h e e t

DC Characteristics

Table 7. CMOS Compatible

Parameter

Description

Test Conditions

Min

Typ

Max

± 1.0

35

Unit

µA

V_IN= V_SSto V_CC

,

I_LI

Input Load Current

V

_CC= V_{CC max}

I_LIT

I_LO

A9 Input Load Current

Output Leakage Current

V_CC= V_{CC max}; A9 = 11.0 V

µA

V_OUT= V_SSto V_CC

,

± 1.0

µA

V

_CC= V_{CC max}

5 MHz

1 MHz

5 MHz

1 MHz

5

1

5

1

10

3

CE# = V_IL,OE# ₌V_IH,

Byte Mode

V_CCActive Read Current

(Notes 1, 2)

I_CC1

mA

10

3

CE# = V_IL,OE# ₌V_IH,

Word Mode

V_CCActive Write Current

(Notes 2, 3, 5)

I_CC2

I_CC3

I_CC4

CE# = V_IL,OE# ₌V_IH

15

30

V_CCStandby Current (Note 2)

V_CCReset Current (Note 2)

CE#, RESET# = V_CC± ±0.2 V

RESET# = V_SS± ±0.2 V

V_IH= V_CC± ±0.2 V;

0.2

5

µA

Automatic Sleep Mode

(Notes 2, 3)

I_CC5

0.2

5

µA

V

_IL= V_SS± ±0.2 V

V_IL

V_IH

Input Low Voltage

Input High Voltage

–0.5

0.3 x V_CC

V_CC+ 0.3

V

0.7 x V_CC

Voltage for Autoselect and

Temporary Sector Unprotect

V_ID

V

_CC= 2.0 V

9.0

11.0

V

V_OL1

V_OL2

V_OH1

V_OH2

V_LKO

I_OL= 2.0 mA, V_CC= V_{CC min}

I_OL= 100 µA, V_CC= V_{CC min}

I_OH= –2.0 mA, V_CC= V_{CC min}

I_OH= –100 µA, V_CC= V_{CC min}

0.25

0.1

V

Output Low Voltage

0.85 x V_CC

V_CC–0.1

1.2

Output High Voltage

Low V_CCLock-Out Voltage (Note 4)

1.5

Notes:

1. The I_CCcurrent listed is typically less than 1 mA/MHz, with OE# at V_IH. Typical V_CCis 2.0 V.

2. The maximum I_CCspecifications are tested with V_CC= V_CCmax.

3.

I_CCactive while Embedded Erase or Embedded Program is in progress.

4. Automatic sleep mode enables the low power mode when addresses remain stable for t_ACC+ 50 ns.

5. Not 100% tested.

April 27, 2005

Am29SL800D

27

D a t a S h e e t

DC Characteristics (Continued)

Zero Power Flash

20

15

10

5

0

500

1000

1500

2000

2500

3000

3500

4000

Time in ns

Note: Addresses are switching at 1 MHz

Figure 9.

I

Current vs. Time (Showing Active and Automatic Sleep Currents)

CC1

10

8

6

2.2 V

4

1.8 V

2

0

1

2

3

4

5

Frequency in MHz

Note: T = 25 °C

Figure 10. Typical I

vs. Frequency

CC1

28

Am29SL800D

April 27, 2005

D a t a S h e e t

Test Conditions

Table 8. Test Specifications

-90,

-120,

Test Condition

Output Load

-100

-150

Unit

1 TTL gate

Device

Under

Test

Output Load Capacitance, C_L

(including jig capacitance)

30

100

pF

Input Rise and Fall Times

Input Pulse Levels

5

0.0–2.0

ns

V

C

L

Input timing measurement

reference levels

1.0

V

Output timing measurement

reference levels

Figure 11. Test Setup

Table 9. Key to Switching Waveforms

WAVEFORM

INPUTS

OUTPUTS

Steady

Changing from H to L

Changing from L to H

Don’t Care, Any Change Permitted

Does Not Apply

Changing, State Unknown

Center Line is High Impedance State (High Z)

2.0 V

1.0 V

Input

Measurement Level

Output

0.0 V

Figure 12. Input Waveforms and Measurement Levels

April 27, 2005

Am29SL800D

29

D a t a S h e e t

AC Characteristics

Table 10. Read Operations

Parameter

Speed Options

JEDEC

Std

Description

Test Setup

-90

-100

-120

-150

Unit

90

(Note 3)

t_AVAV

t_RC

Read Cycle Time (Note 1)

Address to Output Delay

Chip Enable to Output Delay

Min

Max

100

120

150

ns

CE# = V_IL

OE# = V_IL

90

(Note 3)

t_AVQV

t_ACC

100

120

150

ns

90

(Note 3)

t_ELQV

t_CE

OE# = V_IL

100

35

120

50

150

65

t_GLQV

t_EHQZ

t_GHQZ

t_OE

t_DF

Output Enable to Output Delay

Chip Enable to Output High Z (Note 1)

Output Enable to Output High Z (Note 1)

Max

Min

30

ns

16

0

Read

Output Enable

Hold Time (Note 1)

t_OEH

Toggle and

Min

30

0

ns

Data# Polling

Output Hold Time From Addresses, CE# or OE#,

Whichever Occurs First (Note 1)

t_AXQX

t_OH

Notes:

1. Not 100% tested.

2. See Figure 11, on page 29 and Table 8 on page 29 for test specifications

3.

V

_CCmin. = 1.7V

.

t

RC

Addresses Stable

ACC

Addresses

CE#

t

D

t

O

OE#

t

OEH

WE#

t

CE

t

O

HIGH Z

Output Valid

Outputs

RESET#

RY/BY#

0 V

Figure 13. Read Operations Timings

30

Am29SL800D

April 27, 2005

D a t a S h e e t

AC Characteristics

Table 11. Hardware Reset (RESET#)

Parameter

JEDEC

Std

Description

All Speed Options

Unit

RESET# Pin Low (During Embedded Algorithms) to Read or Write

t_READY

Max

20

µs

(see Note)

RESET# Pin Low (NOT During Embedded Algorithms) to Read or

Write (see Note)

t_READY

Max

500

ns

t_RP

t_RH

t_RPD

t_RB

RESET# Pulse Width

RESET# High Time Before Read (see Note)

RESET# Low to Standby Mode

RY/BY# Recovery Time

Min

500

200

20

ns

µs

ns

0

Note: Not 100% tested.

RY/BY#

CE#, OE#

RESET#

t

RH

t

RP

t

Ready

Reset Timings NOT during Embedded Algorithms

Reset Timings during Embedded Algorithms

t

Ready

RY/BY#

t

RB

CE#, OE#

RESET#

t

RP

Figure 14. RESET# Timings

April 27, 2005

Am29SL800D

31

D a t a S h e e t

AC Characteristics

Table 12. Word/Byte Configuration (BYTE#)

Parameter

Speed Options

JEDEC

Std

t_{ELFL/ ELFH}

t_FLQZ

t_FHQV

Description

CE# to BYTE# Switching Low or High

BYTE# Switching Low to Output HIGH Z

BYTE# Switching High to Output Active

-90

-100

-120

-150

Unit

ns

t

Max

Min

10

50

90

50

60

ns

100

120

150

ns

CE#

OE#

BYTE#

t

ELFL

Data Output

(DQ0–DQ14)

Data

Output

BYTE#

Switching

from word

to byte

DQ0–DQ14

DQ15/A-1

mode

Address

Input

DQ15

Output

t

FLQZ

t

ELFH

BYTE#

Switching

from byte to

word mode

Data

Output

Data Output

(DQ0–DQ14)

DQ0–DQ14

DQ15/A-1

Address

Input

DQ15

Output

t

FHQV

Figure 15. BYTE# Timings for Read Operations

CE#

The falling edge of the last WE# signal

WE#

BYTE#

t_SET

(t_AS

)

t_HOLD(t_AH

)

Note: Refer to the Erase/Program Operations table for t_ASand t_AHspecifications.

Figure 16. BYTE# Timings for Write Operations

32

Am29SL800D

April 27, 2005

D a t a S h e e t

AC Characteristics

Table 13. Erase/Program Operations

Parameter

Speed Options

JEDEC

t_AVAV

Std

t_WC

t_AS

Description

Write Cycle Time (Note 1)

Address Setup Time

Address Hold Time

Data Setup Time

-90

-100

-120

-150

Unit

ns

Min

90

100

120

150

t_AVWL

t_WLAX

t_DVWH

t_WHDX

0

ns

t_AH

45

50

60

70

ns

t_DS

ns

t_DH

Data Hold Time

0

ns

t_OES

Output Enable Setup Time

ns

Read Recovery Time Before Write

(OE# High to WE# Low)

t_GHWL

Min

0

ns

t_ELWL

t_WHEH

t_WLWH

t_WHWL

t_CS

t_CH

CE# Setup Time

CE# Hold Time

Min

Typ

Min

0

ns

t_WP

Write Pulse Width

Write Pulse Width High

45

50

60

70

t_WPH

30

5

Byte

t_WHWH1

Programming Operation (Notes 1, 2)

µs

Word

7

t_WHWH2

t_VCS

Sector Erase Operation (Notes 1, 2)

V_CCSetup Time

0.7

50

0

sec

µs

t_RB

Recovery Time from RY/BY#

Program/Erase Valid to RY/BY# Delay

ns

t_BUSY

200

ns

Notes:

1. Not 100% tested.

2. See the Table 16 on page 40 for more information.

April 27, 2005

Am29SL800D

33

D a t a S h e e t

AC Characteristics

Program Command Sequence (last two cycles) Read Status Data (last two cycles)

t

AS

t

WC

Addresses

555h

PA

t

AH

CE#

OE#

t

C

t

WHWH1

t

W

WE#

t

WPH

t

CS

t

D

t

D

PD

D_OUT

A0h

Statu

Data

t

RB

BUSY

RY/BY#

V

CC

t

VCS

Notes:

1. PA = program address, PD = program data, D_OUTis the true data at the program address.

2. Illustration shows device in word mode.

Figure 17. Program Operation Timings

34

Am29SL800D

April 27, 2005

D a t a S h e e t

AC Characteristics

Erase Command Sequence (last two cycles)

Read Status Data

t

AS

VA

Addresses

CE#

2AAh

SA

555h for chip erase

t

A

t

C

OE#

t

W

WE

t

WP

WHWH

t

CS

t

D

t

D

In

Data

Complete

55h

30h

Progress

10 for Chip Erase

t

RB

BUSY

RY/BY#

t

VC

V

CC

Notes:

1. SA = sector address (for Sector Erase), VA = Valid Address for reading status data (see “Write Operation Status”).

2. Illustration shows device in word mode.

Figure 18. Chip/Sector Erase Operation Timings

April 27, 2005

Am29SL800D

35

D a t a S h e e t

AC Characteristics

Addresses

VA

ACC

VA

t

CE

CE#

t

CH

t

OE

t

OEH

WE#

t

OH

High Z

DQ7

Valid Data

Complement

Compleme

Status

Tru

DQ0–DQ6

Status

Tru

Valid Data

t_BUSY

RY/BY#

Note: VA = Valid address. Illustration shows first status cycle after command sequence, last status read cycle, and array data read cycle.

Figure 19. Data# Polling Timings (During Embedded Algorithms)

Addresses

CE#

VA

ACC

VA

t

CE

t

CH

t

OE

t

OEH

WE#

t

OH

High

DQ6/DQ2

RY/BY#

Valid

(second read)

Valid

(stops toggling)

Valid Data

(first read)

t

BUS

Note: VA = Valid address; not required for DQ6. Illustration shows first two status cycle after command sequence, last status read cycle, and

array data read cycle.

Figure 20. Toggle Bit Timings (During Embedded Algorithms)

36

Am29SL800D

April 27, 2005

D a t a S h e e t

AC Characteristics

Enter

Embedded

Erasing

Erase

Suspend

Enter Erase

Suspend Program

Erase

Resume

Erase

Complete

Erase

Erase Suspend

Read

Erase

Suspend

Program

WE#

Erase

Erase Suspend

Read

DQ6

DQ2

Note: The system may use CE# or OE# to toggle DQ2 and DQ6. DQ2 toggles only when read at an address within an erase-suspended sector.

Figure 21. DQ2 vs. DQ6

Table 14. Temporary Sector Unprotect

Parameter

JEDEC

Std

Description

V_IDRise and Fall Time

All Speed Options

Unit

t_VIDR

Min

500

ns

RESET# Setup Time for Temporary Sector

Unprotect

t_RSP

4

µs

10 V

RESET#

0 or 1.8 V

t_VIDR

0 or 1.8 V

t

VIDR

Program or Erase Command Sequence

CE#

WE#

t_RSP

RY/BY#

Figure 22. Temporary Sector Unprotect Timing Diagram

April 27, 2005

Am29SL800D

37

D a t a S h e e t

AC Characteristics

V

ID

IH

V

RESET#

SA, A6,

A1, A0

Valid*

Status

Sector Protect/Unprotect

60h 60h

Verify

40h

Data

Sector Protect: 150

µs

1 µs

CE#

WE#

OE#

* For sector protect, A6 = 0, A1 = 1, A0 = 0. For sector unprotect, A6 = 1, A1 = 1, A0 = 0.

Figure 23. Sector Protect/Unprotect Timing Diagram

38

Am29SL800D

April 27, 2005

D a t a S h e e t

AC Characteristics

Table 15. Alternate CE# Controlled Erase/Program Operations

Parameter

Speed Options

JEDEC

t_AVAV

Std

t_WC

t_AS

Description

-90

-100

-120

-150

Unit

ns

Write Cycle Time (Note 1)

Address Setup Time

Address Hold Time

Data Setup Time

Min

90

100

120

150

t_AVEL

0

ns

t_ELAX

t_DVEH

t_EHDX

t_AH

45

50

60

70

ns

t_DS

ns

t_DH

Data Hold Time

0

ns

t_OES

Output Enable Setup Time

ns

Read Recovery Time Before Write

(OE# High to WE# Low)

t_GHEL

Min

0

ns

t_WLEL

t_EHWH

t_ELEH

t_EHEL

t_WS

t_WH

t_CP

WE# Setup Time

WE# Hold Time

Min

Typ

0

ns

CE# Pulse Width

CE# Pulse Width High

45

50

60

70

t_CPH

30

5

Byte

Programming Operation

(Notes 1, 2)

t_WHWH1

µs

Word

7

t_WHWH2

t_WHWH2Sector Erase Operation (Notes 1, 2)

0.7

sec

Notes:

1. Not 100% tested.

2. See the “Erase and Programming Performance” section for more information.

April 27, 2005

Am29SL800D

39

D a t a S h e e t

AC Characteristics

555 for program PA for program

2AA for erase

SA for sector erase

555 for chip erase

Data# Polling

PA

Addresses

t

WC

AS

t

AH

t

WH

WE#

OE#

t

GHEL

t

WHWH1 or

t

CP

CE#

t

WS

CPH

t

BUS

t

D

t

D

DQ7# D_OUT

Data

t

RH

A0 for program PD for program

55 for erase

30 for sector erase

10 for chip erase

RESET

RY/BY#

Notes:

1. PA = program address, PD = program data, DQ7# = complement of the data written, D_OUT= data written

2. Figure indicates the last two bus cycles of command sequence.

3. Word mode address used as an example.

Figure 24. Alternate CE# Controlled Write Operation Timings

Table 16. Erase and Programming Performance

Parameter

Typ (Note 1)

Max (Note 2)

Unit

s

Comments

Sector Erase Time

Chip Erase Time

0.7

14

5

15

Excludes 00h programming prior

to erasure (Note 4)

s

Byte Programming Time

150

210

16

µs

s

Word Programming Time

7

Excludes system level overhead

(Note 5)

Byte Mode

Word Mode

5.3

3.7

Chip Programming Time

(Note 3)

11

s

Notes:

1. Typical program and erase times assume the following conditions: 25°C, 2.0 V V_CC, 1,000,000 cycles. Additionally, programming typicals

assume checkerboard pattern.

2. Under worst case conditions of 90°C, V_CC= 1.8 V, 1,000,000 cycles.

3. The typical chip programming time is considerably less than the maximum chip programming time listed, since most bytes program faster

than the maximum program times listed.

4. In the pre-programming step of the Embedded Erase algorithm, all bytes are programmed to 00h before erasure.

5. System-level overhead is the time required to execute the two- or four-bus-cycle sequence for the program command. See Table 5 for further

information on command definitions.

6. The device has a minimum guaranteed erase and program cycle endurance of 1,000,000 cycles.

40

Am29SL800D

April 27, 2005

D a t a S h e e t

Table 17. Latchup Characteristics

Description

Min

Max

Input voltage with respect to V_SSon all pins except I/O pins

(including A9, OE#, and RESET#)

–1.0 V

11.0 V

Input voltage with respect to V_SSon all I/O pins

–0.5 V

V_CC+ 0.5 V

+100 mA

V

_CCCurrent

–100 mA

Includes all pins except V_CC. Test conditions: V_CC= 1.8 V, one pin at a time.

Table 18. TSOP Pin Capacitance

Parameter Symbol

Parameter Description

Input Capacitance

Test Setup

V_IN= 0

Typ

6

Max

7.5

12

Unit

pF

C_IN

C_OUT

C_IN2

Output Capacitance

Control Pin Capacitance

V_OUT= 0

V_IN= 0

8.5

7.5

pF

9

pF

Notes:

1. Sampled, not 100% tested.

2. Test conditions T_A= 25°C, f = 1.0 MHz.

Table 19. Data Retention

Parameter

Test Conditions

150°C

Min

10

Unit

Years

Minimum Pattern Data Retention Time

125°C

20

April 27, 2005

Am29SL800D

41

D a t a S h e e t

Physical Dimensions

TS 048–48-Pin Standard TSOP

Dwg rev AA; 10/99

42

Am29SL800D

April 27, 2005

D a t a S h e e t

Physical Dimensions

TSR048–48-Pin Reverse TSOP

Dwg rev AA; 10/99

April 27, 2005

Am29SL800D

43

D a t a S h e e t

Physical Dimensions

FBA048–48-Ball Fine-Pitch Ball Grid Array (FBGA)

6 x 8 mm package

Dwg rev AF; 10/99

44

Am29SL800D

April 27, 2005

D a t a S h e e t

Physical Dimensions

FBC048 – 48-Ball Fine-Pitch Ball Grid Array (FBGA)

8 x 9 mm package

Dwg rev AF; 10/99

April 27, 2005

Am29SL800D

45

D a t a S h e e t

Physical Dimensions

VBK 048 - 48 Ball Fine-Pitch Ball Grid Array (FBGA)

8.15 x 6.15 mm

0.10 (4X)

D1

A

D

6

5

4

3

2

1

7

e

SE

E1

E

H

G

F

E

D

C

B

A

INDEX MARK

6

B

A1 CORNER

PIN A1

7

fb

SD

CORNER

10

f

0.08M

0.15M

C

TOP VIEW

A

B

BOTTOM VIEW

0.10C

0.08C

A2

A

SEATING PLANE

C

A1

SIDE VIEW

NOTES:

PACKAGE

JEDEC

VBK 048

1.DIMENSIONING AND TOLERANCING PER ASME Y14.5M-1994.

2.ALL DIMENSIONS ARE IN MILLIMETERS.

N/A

8.15 mm

x

6.15 mm NOM

3.BALL POSITION DESIGNATION PER JESD 95-1, SPP-010 (EXCEPT

AS NOTED).

PACKAG

E

SYMBOL

MIN

NOM

MAX

NOTE

4.

e

REPRESENTS THE SOLDER BALL GRID PITCH.

A

A1

A2

D

---

1.00 OVERALL THICKNESS

--- BALL HEIGHT

0.76 BODY THICKNESS

BODY SIZE

5.SYMBOL "MD" IS THE BALL ARTORWIXM SIZE IN THE

"D" DIRECTION.

0.18

0.62

---

SYMBOL "ME" IS THE BALL NCOMLAUTMRIX SIZE IN THE

"E" DIRECTION.

---

8.15 BSC.

6.15 BSC.

5.60 BSC.

4.00 BSC.

8

N IS THE TOTAL NUMBER OF SOLDER BALLS.

E

BODY SIZE

6

7

DIMENSION "b" IS MEASURED AT THE MAXIMUM BALL

DIAMETER IN PLANE PARALLEL TO DATUM C.

D1

E1

MD

ME

N

BALL FOOTPRINT

A

SD AND SE ARE MEASURED WITH RETSOPEDCATTUMS

AND AND DEFINE THE POSOIFTITOHNE CENTER

A

B

ROW MATRIX SIZE

TOTAL BALL COUNT

0.43 BALL DIAMETER

BALL PITCH

D

DIRECTION

SOLDER BALL IN THE OUTER ROW.

6

E

WHEN THERE IS AN ODD NUMBER OF SOLDER BALLS IN

THE OUTER ROW PARALLEL TO THEEDDOIRMENSION,

RESPECTIVELY, SD OR SE = 0.000.

48

fb

e

0.35

---

WHEN THERE IS AN EVEN NUMBER OF SOLDER BALLS IN

THE OUTER ROW, SD OR SE = e/2

0.80 BSC.

0.40 BSC.

---

SD

/

SE

SOLDER BALL PLACEMEN

T

8.NOT USED.

DEPOPULATED SOLDER BALLS

9."+" INDICATES THE THEORETICAL CENTER OF DEPOPULATED

BALLS.

10 A1 CORNER TO BE IDENTIFIED BY CHAMFER, LASER OR INK

MARK, METALLIZED MARK INDENTATION OR OTHER MEANS.

3338 \ 16-038.25b

46

Am29SL800D

April 27, 2005

D a t a S h e e t

Revision Summary

Revision A (February 4, 2003)

Initial release.

Revision A+1 (March 17, 2003)

Ordering Information

Corrected typo in table.

Corrected typo to OPNs.

Revision A+2 (June 10, 2004)

Ordering Information

Added Pb-free package OPNs.

Revision A+3 (October 27, 2004)

Updated V values

CC

Revision A+4 (April 27, 2005)

Added VBK048 package.

Added Colophon.

Updated Trademark.

Colophon

The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary industrial

use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated (1) for any use that includes fatal risks

or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical

damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile

launch control in weapon system), or (2) for any use where chance of failure is intolerable (i.e., submersible repeater and artificial satellite). Please note that Spansion

LLC will not be liable to you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. Any semiconductor

devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility

and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. If any products described in this

document represent goods or technologies subject to certain restrictions on export under the Foreign Exchange and Foreign Trade Law of Japan, the US Export

Administration Regulations or the applicable laws of any other country, the prior authorization by the respective government entity will be required for export of those

products.

Trademarks

AMD, the AMD logo, and combinations thereof are registered trademarks of Advanced Micro Devices, Inc.

ExpressFlash is a trademark of Advanced Micro Devices, Inc.

Product names used in this publication are for identification purposes only and may be trademarks of their respective companies.

April 27, 2005

Am29SL800D

47


型号：	AM29SL800DB-120WCI
厂家：	SPANSION
描述：	512KX16 FLASH 1.8V PROM, 120ns, PBGA48, 8 X 9 MM, 0.80 MM PITCH, FBGA-48 可编程只读存储器内存集成电路
文件：	总49页 (文件大小：1191K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

AM29SL800DB-120WCI [SPANSION]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB

SI9137LG

SI9122E