HVLED002TR [STMICROELECTRONICS]
High performance current mode LED controller;
| 型号： | HVLED002TR |
| 厂家： | 
ST |
| 描述： | High performance current mode LED controller |
| 文件： | 总19页 (文件大小：481K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
HVLED002
High performance current mode LED controller
Datasheet - production data
Description
The HVLED002 control IC provides the necessary
features to implement off-line or DC to DC fixed
frequency current mode control schemes to
implement LED drivers. Internally implemented
circuits include a trimmed oscillator for the precise
duty cycle control, undervoltage lockout,
a precision reference trimmed for accuracy at the
error amplifier input, a PWM comparator which
also provides current limit control and a totem
pole output stage designed to the source or sink
high peak current. The output stage, suitable for
driving N-channel MOSFETs, is low in the off-
state.
SO-8
Features
Trimmed oscillator for precise frequency
control
Oscillator frequency guaranteed at 250 kHz
Current mode operation to 500 kHz
Latching PWM for cycle-by-cycle current
limiting
Internally trimmed reference with undervoltage
Table 1. Device summary
lockout
Order codes
Package
Packaging
High current totem pole output
HVLED002
Tube
Undervoltage lockout with hysteresis
Low start-up and operating current
SO8
HVLED002TR
Tape and reel
Figure 1. Block diagram
December 2015
DocID028720 Rev 1
1/19
This is information on a product in full production.
www.st.com
Contents
HVLED002
Contents
1
2
3
4
5
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Pin connection and functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.1
5.2
5.3
5.4
5.5
5.6
5.7
Supply voltage and undervoltage lockout . . . . . . . . . . . . . . . . . . . . . . . . . 12
Reference voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Current sense . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Error amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Totem pole output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Typical application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
6
7
Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
6.1
SO-8 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2/19
DocID028720 Rev 1
HVLED002
List of figures
List of figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Figure 9.
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Pin connection (top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Open loop test circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Timing resistor vs. oscillator frequency. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Output deadtime vs. oscillator frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Oscillator discharge current vs. temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Maximum output duty cycle vs. timing resistor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Error amplifier open loop gain and phase vs. frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Current sense input threshold vs. error amplifier output voltage . . . . . . . . . . . . . . . . . . . . . 9
Figure 10. Reference voltage change vs. source current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Figure 11. Reference short-circuit current vs. temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Figure 12. Output saturation voltage vs. load current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Figure 13. Supply current vs. supply voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Figure 14. Oscillator and output waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Figure 15. Error amplifier configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Figure 20. Error amplifier compensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Figure 16. Undervoltage lockout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Figure 17. Current sense circuit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Figure 18. Soft-start circuit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Figure 19. External clock synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Figure 21. Leading edge blanking circuitries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Figure 22. Shutdown circuitries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Figure 23. Typical application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Figure 24. SO-8 package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
DocID028720 Rev 1
3/19
19
Absolute maximum ratings
HVLED002
1
Absolute maximum ratings
(1)
Table 2. Absolute maximum ratings
Parameter
Symbol
Value
Unit
Vi
IO
Supply voltage
30
V
A
Output current
± 1
EO
Output energy (capacitive load)
Analog inputs (pins 2, 3)
Error amplifier output sink current
5
- 0.3 to 5.5
10
µJ
V
mA
1. All voltages are with respect to the pin 5, all currents are positive into the specified terminal.
4/19
DocID028720 Rev 1
HVLED002
Pin connection and functions
2
Pin connection and functions
Figure 2. Pin connection (top view)
Table 3. Pin functions
Description
No. Function
1
2
COMP
VFB
This pin is the error amplifier output and is made available for loop compensation.
This is the inverting input of the error amplifier. It is normally connected to the
switching power supply output through a resistor divider.
A voltage proportional to the inductor current is connected to this input. The PWM
uses this information to terminate the output switch conduction.
3
4
ISENSE
The oscillator frequency and maximum output duty cycle are programmed by the
connecting resistor RT to VREF and the capacitor CT to ground. An operation to
500 kHz is possible.
RT/CT
5
6
7
8
GROUND This pin is the ground reference of the device.
This output directly drives the gate of a power MOSFET. Peak currents up to 1 A
are sourced and sunk by this pin.
OUTPUT
Vi
This pin is the positive supply of the control IC.
This is the reference output. It provides the charging current for the capacitor CT
through the resistor RT.
VREF
3
Thermal data
Table 4. Thermal data
Description
Symbol
SO8
Unit
Rth j-amb
Tstg
Thermal resistance junction ambient
Storage temperature range
150
°C/W
°C
-65 to 150
-40 to 150
300
TJ
Junction operating temperature
Lead temperature (soldering 10 s)
°C
TL
°C
DocID028720 Rev 1
5/19
19
Electrical characteristics
HVLED002
4
Electrical characteristics
Unless otherwise stated, these specifications apply for 0 ≤ T
≤ 85 °C; V = 15 V;
amb
i
(a)
R = 10 K; C = 3.3 nF
.
T
T
Table 5. Electrical characteristics
Test conditions
Symbol
Parameter
Min. Typ. Max. Unit
SUPPLY VOLTAGE
Vi Max. operative volt.
REFERENCE SECTION
VREF Output voltage
25
V
TJ = 25 °C, Io = 1 mA
4.95 5.00 5.05
V
mV
mV
mV/°C
V
VREF Line regulation
VREF Load regulation
VREF/T Temperature stability
Total output variation
12 V ≤ Vi ≤ 25 V
2
3
20
25
1 ≤ Io ≤ 20 mA
(1)
0.2
Line, load, temperature
4.82
-30
5.18
25
eN
Output noise voltage
Long term stability
Output short-circuit
10 Hz ≤ f ≤ 10 KHz, Tj = 25 °C(1)
50
5
µV
T
amb = 125 °C, 1000 hrs(1)
mV
mA
ISC
-100 -180
OSCILLATOR SECTION
TJ = 25 °C
49
48
52
-
55
56
fOSC
Frequency
TA = 0 to 85 °C
KHz
TJ = 25 °C (RT = 6.2 k, CT = 1 nF)
225
250
275
fOSC/V Frequency change with volt.
VCC = 12 V to 25 V
-
-
0.2
0.5
1.6
8.3
-
1
-
%
%
fOSC/T Frequency change with temp. Tamb = 0 °C to 85 °C
VOSC Oscillator voltage swing Peak-to-peak
Idischg Discharge current (VOSC = 2 V) TJ = 25 °C
TA = 0°C to 85°C
-
-
V
7.8
7.6
8.8
8.8
mA
mA
ERROR AMPLIFIER SECTION
VREF,EA Input voltage
V(COMP) = 2.5 V
VFB = 5 V
2.42 2.50 2.58
V
µA
Ib
Input bias current
AVOL
-0.1
90
1
-2
2 V ≤ Vo ≤ 4 V
65
0.7
60
2
dB
BW
Unity gain bandwidth
TJ = 25 °C(1)
MHz
dB
PSRR Power supply reject. ratio
Io Output sink current
12 V ≤ Vi ≤ 25 V
V(VFB) = 2.7 V, V(COMP) = 1.1 V
70
12
mA
a. Max. package power dissipation limits must be respected; low duty cycle pulse techniques are used during the test
maintaining TJ as close to Tamb as possible.
6/19
DocID028720 Rev 1
HVLED002
Electrical characteristics
Table 5. Electrical characteristics (continued)
Symbol
Parameter
Test conditions
Min.
Typ.
Max.
Unit
Output source current
VCOMP high
V(VFB) = 2.3 V, V(COMP) = 5 V
-0.5
-1
mA
Io
V(VFB) = 2.3 V; RL = 15 K between
5
6.2
0.8
V
V
COMP and ground
V(VFB) = 2.7 V; RL = 15 K between
COMP and VREF
VCOMP low
1.1
CURRENT SENSE SECTION
GV Gain
MAXCS Maximum input signal
(2) (3)
,
3
V/V
mV
dB
µA
ns
V(COMP) = 5.6 V
258
267
70
276
SVR
Ib
Supply voltage rejection
Input bias current
Delay to output
12 ≤ Vi ≤ 25 V(1)
-2
-10
150
300
OUTPUT SECTION
Output low level
ISINK = 20 mA
0.1
1.6
13.5
13.5
0.1
50
0.4
2.2
V
V
VOL
ISINK = 200 mA
Output high level
ISOURCE = 20 mA
13
12
V
VOH
ISOURCE = 200 mA
VCC = 6 V; ISINK = 1 mA
TJ = 25 °C; CL = 1 nF(1)
TJ = 25 °C; CL = 1 nF(1)
V
VOLS
UVLO saturation
Rise time
1.1
150
150
V
tr
tf
ns
ns
Fall time
50
UNDERVOLTAGE LOCKOUT SECTION
VON
Start threshold
Increasing voltage
Decreasing voltage
7.8
7.0
8.4
7.6
9.0
8.2
V
V
Min. operating voltage after
turn-on
VOFF
PWM SECTION
Maximum duty cycle
94
96
100
0
%
%
Minimum duty cycle
TOTAL STANDBY CURRENT
Ist
Ii
Start-up current
0.3
12
0.5
17
mA
mA
Operating supply current
V(VFB) = V(COMP) = 0 V
1. These parameters, although guaranteed, are not 100% tested in production.
2. Parameter measured at the trip point of the latch with V(VFB) = 0.
3. Gain defined as : A = V(COMP)/V(ISENSE) ; 0 ≤ V(ISENSE) ≤ 267 mV.
DocID028720 Rev 1
7/19
19
Electrical characteristics
HVLED002
Figure 3. Open loop test circuit
VREF
RT
2N2222
A
Vi
VREF
0.1 μF
COMP
VFB
8
1
2
7
Vi
ERROR AMP.
ADJUST
1W
0.1 μF
HVLED002
ISENSE
RT/CT
ISENSE
ADJUST
3
OUTPUT
GROUND
6
OUTPUT
4
5
CT
GROUND
AM039820
High peak currents associated with capacitive loads necessitate careful grounding
techniques. Timing and bypass capacitors should be connected close to the pin 5 in a single
point ground. The transistor and 5 K potentiometer are used to sample the oscillator
waveform and apply an adjustable ramp to the pin 3.
Figure 4. Timing resistor vs. oscillator
frequency
Figure 5. Output deadtime vs. oscillator
frequency
8/19
DocID028720 Rev 1
HVLED002
Electrical characteristics
Figure 6. Oscillator discharge current
Figure 7. Maximum output duty cycle vs. timing
resistor
vs. temperature
Figure 8. Error amplifier open loop gain and
phase vs. frequency
Figure 9. Current sense input threshold
vs. error amplifier output voltage
DocID028720 Rev 1
9/19
19
Electrical characteristics
HVLED002
Figure 10. Reference voltage change vs. source
current
Figure 11. Reference short-circuit current
vs. temperature
Figure 12. Output saturation voltage vs. load
current
Figure 13. Supply current vs. supply voltage
Figure 14. Oscillator and output waveforms
Figure 15. Error amplifier configuration
10/19
DocID028720 Rev 1
HVLED002
Electrical characteristics
Figure 16. Undervoltage lockout
Figure 17. Current sense circuit
Figure 18. Soft-start circuit
Figure 19. External clock synchronization
Figure 20. Error amplifier compensation
ꢀ
'SP ꢃ7
ꢆ ꢃ7
0
ꢃN"
3
J
ꢄ3
ꢀ
ꢁ
ꢄ
ꢂ
&"
3
3
$
3
E
G
G
ꢅ
&SSPSꢃBNQMJGJFSꢃDPNQFOTBUJP ꢃDJSDVJUꢃGPSꢃTUBCJMJ[JO ꢃBO ꢃDVSSFOUꢃNPE ꢃUPQPMPH ꢃFYDFQU
GPSꢃCPPTUꢃBO ꢃGMZCBD ꢃDPOWFSUFS ꢃPQFSBUJO ꢃXJU ꢃDPOUJOVPV ꢃJOEVDUPSꢃDVSSFOUꢆ
ꢀ
'SP ꢃ7
ꢆ ꢃ7
0
ꢃN"
3
1
ꢄ3
ꢀ
3
J
ꢁ
ꢄ
ꢂ
&"
3
$
3
$
3
1
E
G
G
ꢅ
&SSPSꢃBNQMJGJFSꢃDPNQFOTBUJP ꢃDJSDVJUꢃGPSꢃTUBCJMJ[JO ꢃDVSSFOUꢃNPE ꢃCPPTUꢃBO ꢃGMZCBDL
UPQPMPHJF ꢃPQFSBUJO ꢃXJU ꢃDPOUJOVPV ꢃJOEVDUPSꢃDVSSFOUꢆ
"
.ꢇ
ꢈ
ꢉ
ꢊ
ꢂ
ꢋ
DocID028720 Rev 1
11/19
19
Application information
HVLED002
5
Application information
5.1
Supply voltage and undervoltage lockout
The HVLED002 device is able to operate with a very wide range of supply voltage between
8.4 V and 30 V. The UVLO circuit insures that VCC is adequate to make the HVLED002 fully
operational before enabling the output stage. Figure 16 shows that the UVLO turn-on and
turn-off thresholds are fixed internally at 8.4 V and 7.6 V respectively. The hysteresis
prevents V oscillations during power sequencing and the start-up current is less than
CC
1 mA.
During UVLO, the output driver is in a low state and it can easily sink 1 mA, enough to
insure the MOSFET is held off.
5.2
Reference voltage
The HVLED002 contains a precision reference voltage (5 V) that generates all the internal
reference voltages such as the error amplifier's reference (connected to its non-inverting
input), current sense clamp limit (MAXCS) and oscillator's internal bias currents and
thresholds.
The reference voltage is also available on the VREF pin that, thanks to its high output
current capability (over 20 mA), is able to supply not only nearby passive circuitries but also
auxiliary microcontrollers.
The pin must be bypassed with at least a 0.1 µF ceramic capacitor placed as close as
possible to the respective VREF and GND pins.
5.3
Oscillator
The HVLED002 oscillator is programmed as shown in Figure 14. The timing capacitor CT is
charged from a reference voltage (e.g.: VREF) through the timing resistor RT, and
discharged by an internal current source.
The MOSFET is turned on (GD pin high) when the oscillator starts the charge of the CT. As
soon as the voltage of the CT reaches an upper threshold the internal discharge current is
activated until the CT voltage reaches a lower threshold. This occurrence initiates a new
oscillator cycle.
The difference between the upper and the lower thresholds (Vosc) determines the duration
of charging and discharging time. During the discharging time (also called deadtime) the
MOSFET is off and any spurious GD triggering is avoided. The deadtime also limits the
maximum obtainable duty cycle.
The oscillator can be differently connected to external circuitry to obtain different operating
schemes. Connecting the RT to VREF a very accurate fixed frequency operation is
achieved: the RT,CT combinations are plot into Figure 5 on page 8, Figure 6 and Figure 8
for a quick reference, or calculated as follows:
Equation 1
FOSC (kHz) = 1.72 / [RT (k) x CT (µF)]
12/19
DocID028720 Rev 1
HVLED002
Application information
Connecting the RT to a variable voltage, dependency of the operating frequency on said
voltage is introduced. A pull-down switch can be used to reset the CT during the MOSFET's
on time, for example to operate in fixed off time. A synchronous operation is also possible
using circuitries like the one proposed as an example in Figure 19. The HVLED002
oscillator can be used to a maximum of 500 kHz.
5.4
Current sense
The peak current mode operation of the HVLED002 is made by the embedded current
sense comparator: the said element turns off the MOSFET as soon as the current sense
input voltage is greater than the internal threshold derived by the COMP pin voltage
(Figure 17).
The current sense pin (ISENSE) is normally connected to a shunt resistor, put in series with
the main switch, but different connections are also possible.
Under the normal operation the threshold voltage (VCS) is controlled by the E/A according
to the following relation:
Equation 2
VCS = 1/3 * (VCOMP - 1.4 V)
VCS is upper limited to MAXCS to reduce the shunt resistor power dissipation without the
need of current transformers or offsets circuitries. This parameter is beneficial in those
applications where both the peak current accuracy and the operating power dissipation are
critical aspects (e.g.: LED secondary side LED current regulators).
When the sensing current resistor is in series with the power switch, the current waveform
will often have a large spike at its leading edge due to parasitic capacitances and gate driver
charging currents. A very simple leading edge blanking (LEB) circuit consists on an RC filter,
but more effective active circuitries are also possible.
Figure 21. Leading edge blanking circuitries
065165
ꢌ
*
*
4
4
$
3
)7-&%ꢇꢇꢄ
)7-&%ꢇꢇꢄ
*4&/4&
ꢈ
3
*4&/4&
$
ꢈ
ꢅ
ꢅ
3
4
3
4
(/%
(/%
"
.ꢇ
ꢈ
ꢉ
ꢊ
ꢂ
ꢌ
DocID028720 Rev 1
13/19
19
Application information
HVLED002
5.5
Error amplifier
An error amplifier (E/A) structure is present in the HVLED002 (Figure 15 on page 10). The
non-inverting input is internally connected to a very precise reference voltage (2.5 V ± 2%).
The E/A output and inverting pin are connected respectively to the pin 1 and 2, available for
external compensation. The E/A output will source at least 0.5 mA and sink 2 mA. Figure 8
on page 9 shows the open loop frequency response of the E/A.
The output of the error amplifier can be forced to ground in different ways to shut down the
application as shown in Figure 22.
Figure 22. Shutdown circuitries
4
OSC
8
R
BIAS
R
+
1 mA
2R
+
-
2
1
EA
R
5
2N
3905
2N
3903
The SCR must be selected for a holding current of less than 0.5 mA at T
.
A(min)
The simple two-transistor circuit can be used in place of the SCR as shown. All resistors are 10 K
.
AM039818
5.6
Totem pole output
The HVLED002 has a single totem pole output which can be operated to the ± 1 Amp peak
current for driving MOSFET gates, and a + 200 mA average current for bipolar power
transistors.
Cross conduction between the driver's output transistors is minimal, the average added
power with VIN = 30 V is around 80 mW at 200 kHz.
Limiting the peak current through the IC is accomplished by placing a resistor between the
totem pole output and the gate of the MOSFET. Without this resistor, the peak current is
limited only by the dV/dT rate of the totem pole switching and the FET gate capacitance.
An additional discharging diode can be put in parallel with the said limiting resistor to quickly
turn off the MOSFET, reducing the switching losses and the control to output delay.
14/19
DocID028720 Rev 1
HVLED002
Application information
5.7
Typical application
The HVLED002 device can be used as a secondary side step-down current regulator in the
multiple staged LED driver - see Figure 23. It is easy to configure the device to drive an
inverse (or modified) buck topology based on the fixed off-time (FOT) algorithm.
The MOSFET remains on until the current sense threshold is reached; during the on time,
the oscillator remains reset to ground. The current sense threshold is set by the saturation
of the E/A to MAXCS to guarantee the higher precision as possible.
The MOSFET is then turned off and the oscillator is released: the resulting off time is fixed
by the charging of the CT by RT, connected to VREF.
An optional auxiliary microcontroller, supplied by VREF itself can be used to dim the LED
current according to the information sent to the application by a remote controller.
Figure 23. Typical application
V
IN
Vaux
)
5.6 V(1
COMP
D
VFB
1
Vi
2
8
7
6
VDD
VREF
L
OUTPUT
Isense
Q
1
μC
HVLED002
User interface
GPIO
3
RT/CT
4
5
GND
R
S
GROUND
Osc. reset
Dimming
1. Optional for better performances.
DocID028720 Rev 1
15/19
19
Package information
HVLED002
6
Package information
In order to meet environmental requirements, ST offers these devices in different grades of
®
®
ECOPACK packages, depending on their level of environmental compliance. ECOPACK
specifications, grade definitions and product status are available at: www.st.com.
®
ECOPACK is an ST trademark.
6.1
SO-8 package information
Figure 24. SO-8 package outline
$0ꢀꢀꢁꢂꢁ9ꢀ
16/19
DocID028720 Rev 1
HVLED002
Package information
Table 6. SO-8 package mechanical data
Dimensions (mm)
Typ.
Dimensions (inch)
Symbol
Min.
Max.
Min.
Typ.
Max.
A
A1
A2
b
1.750
0.250
0.0689
0.0098
0.100
1.250
0.280
0.170
4.800
5.800
3.800
0.0039
0.0492
0.0110
0.0067
0.1890
0.2283
0.1496
0.480
0.230
5.000
6.200
4.000
0.0189
0.0091
0.1969
0.2441
0.1575
c
D(1)
4.900
6.000
3.900
1.270
0.1929
0.2362
0.1535
0.0500
E
E1(2)
e
h
0.250
0.400
0.500
1.270
0.0098
0.0157
0.0197
0.0500
L
L1
k
1.040
0.0409
0°
8°
0°
8°
ccc
0.10
0.0039
1. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold Flash, protrusions or gate burrs
shall not exceed 0.15 mm in total (both sides).
2. Dimension “E1” does not include interlead Flash or protrusions. Interlead Flash or protrusions shall not
exceed 0.25 mm per side.
DocID028720 Rev 1
17/19
19
Revision history
HVLED002
7
Revision history
Table 7. Document revision history
Date
Revision
Changes
15-Dec-2015
1
Initial release.
18/19
DocID028720 Rev 1
HVLED002
IMPORTANT NOTICE – PLEASE READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and
improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on
ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order
acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or
the design of Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2015 STMicroelectronics – All rights reserved
DocID028720 Rev 1
19/19
19
相关型号：
HVM10
HIGH VOLTAGE ASSEMBLIED RECTIFIER (VOLTAGE RANGE 5000 to 16000 Volts CURRENT 0.35 Amperes)
RECTRON
©2020 ICPDF网 联系我们和版权申明