L6911E_07 [STMICROELECTRONICS]
5-Bit programmable step down controller with synchronous rectification; 采用同步整流5位可编程降压控制器
| 型号： | L6911E_07 |
| 厂家： | 
ST |
| 描述： | 5-Bit programmable step down controller with synchronous rectification |
| 文件： | 总34页 (文件大小：483K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
L6911E
5-Bit programmable step down controller
with synchronous rectification
Features
■ Operating supply IC voltage from 5V to 12V
buses
■ Up to 1.3A gate current capability
SO-20
■ TTL-compatible 5 bit programmable output
compliant with VRM 8.5 :
1.050V to 1.825V with 0.025V binary steps
Description
■ Voltage mode PWM control
The device is a power supply controller
specifically designed to provide a high
performance DC/DC conversion for high current
microprocessors. A precise 5 bit digital to analog
converter (DAC) allows to adjust the output
voltage from 1.050 to 1.825 with 25mV binary
steps.
■ Excellent output accuracy: 1ꢀ over line and
temperature variations
■ Very fast load transient response: from 0ꢀ to
100ꢀ Duty Cycle
■ Power good output voltage
■ Overvoltage protection and monitor
■ Overcurrent protection realized using the upper
The high precision internal reference assures the
selected output voltage to be within 1ꢀ. The
high peak current gate drive affords to have fast
switching to the external power mos providing low
switching losses.
MOSFET's R
ds(ON)
■ 200kHz internal oscillator
■ Oscillator externally adjustable from 50kHz to
1MHz
The device assures a fast protection against load
overcurrent and load over-voltage. An external
SCR is triggered to crowbar the input supply in
case of hard overvoltage. An internal crowbar is
also provided turning on the low side mosfet as
long as the over-voltage is detected. In case of
over-current detection, the soft start capacitor is
discharged an the system works in HICCUP
mode.
■ Soft start and inhibit functions
Applications
■ Power supply for advanced
microprocessor core
■ Distributed power supply
Table 1. Device summary
Part Number
Package
TSSOP8
Packaging
L6911E
Tube
L6911ETR
TSSOP8
Tape and reel
April 2007
Rev 3
1/34
www.st.com
34
Contents
L6911E
Contents
1
2
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Pin settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.1
2.2
Pin connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3
Electrical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.1
3.2
Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4
5
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.1
VID Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Device description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Digital to analog converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Soft start and inhibit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Driver section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Monitor and protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Inductor design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Output capacitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Input capacitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Compensation network design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
6
VRM demo board description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
6.1
6.2
6.3
6.4
6.5
Efficiency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Inductor design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Output capacitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Input capacitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Over-current protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
2/34
L6911E
Contents
Connector pin orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
PCB and components layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
7
8
9
10
3/34
Block diagram
L6911E
1
Block diagram
Figure 1. Block diagram
Vcc 5V to12V
Vin 5V to12V
VCC
OCSET
PGOOD
SS
BOOT
MONITOR and
PROTECTION
UGATE
OVP
RT
Vo
1.050V to 1.825V
PHASE
LGATE
PGND
GND
OSC
VD0
VD1
VD2
VD3
VD4
-
D/A
+
PWM
+
-
VSEN
VFB
E/A
D98IN957
COMP
4/34
L6911E
Pin settings
2
Pin settings
2.1
Pin connection
Figure 2. Pin connection (top view)
VSEN
OCSET
SS/INH
VID0
1
20
19
18
17
16
15
14
13
12
11
RT
2
OVP
3
VCC
4
LGATE
PGND
BOOT
UGATE
PHASE
PGOOD
GND
VID1
5
VID2
6
VID3
7
VID4
8
COMP
FB
9
10
D98IN958
2.2
Pin description
Table 2. Pin description
N°
Name
Description
Connected to the output voltage is able to manage over-voltage conditions and
the PGOOD signal.
1
VSEN
A resistor connected from this pin and the upper Mos Drain sets the current
limit protection. The internal 200µA current generator sinks a current from the
drain through the external resistor. The Over-Current threshold is due to the
following equation:
2
OCSET
I
Þ R
IP = --O----C----S----E---T---------------O----C---S----E---T-
RDSon
The soft start time is programmed connecting an external capacitor from this
pin and GND. The internal current generator forces through the capacitor
10µA.
3
SS/INH
VID0 - 4
This pin can be used to disable the device forcing a voltage lower than 0.4V
Voltage Identification Code pins. These input are internally pulled-up and TTL
compatible. They are used to program the output voltage as specified in
Table 6 on page 9 and to set the overvoltage and power good thresholds.
Connect to GND to program a ‘0’ while leave floating to program a ‘1’.
4 - 8
This pin is connected to the error amplifier output and is used to compensate
the voltage control feedback loop.
9
COMP
FB
This pin is connected to the error amplifier inverting input and is used to
compensate the voltage control feedback loop.
10
5/34
Pin settings
L6911E
Table 2. Pin description (continued)
N°
Name
Description
All the internal references are referred to this pin. Connect it to the PCB signal
ground.
11
GND
This pin is an open collector output and is pulled low if the output voltage is not
12
PGOOD within the above specified threshlds.
If not used may be left floating.
This pin is connected to the source of the upper mosfet and provides the return
13
14
15
PHASE
UGATE
BOOT
path for the high side driver. This pin monitors the drop across the upper mosfet
for the current limit.
High side gate driver output.
Bootstrap capacitor pin. Through this pin is supplied the high side driver and
the upper mosfet. Connect through a capacitor to the PHASE pin and through
a diode to Vcc (catode vs boot).
Power ground pin. This pin has to be connected closely to the low side mosfet
source in order to reduce the noise injection into the device
16
17
18
PGND
LGATE
VCC
This pin is the lower mosfet gate driver output
Device supply voltage. The operative supply voltage range is from 4.5 to 12V.
DO NOT CONNECT VIN to 12V if VCC IS 5V.
Over voltage protection. If the output voltage reach the 15ꢀ above the
programmed voltage this pin is driven high and can be used to drive an
external SCR that crowbar the supply voltage.
19
OVP
If not used, it may be left floating.
Oscillator switching frequency pin. Connecting an external resistor from this pin
to GND, the external frequency is increased according to the equation:
5 ⋅ 106
fS = 200kHz + --------------------
RT(kΩ)
Connecting a resistor from this pin to Vcc (12V), the switching frequency is
reduced according to the equation:
20
RT
4 ⋅ 107
fS = 200kHz – --------------------
RT(kΩ)
If the pin is not connected, the switching frequency is 200KHz.
The voltage at this pin is fixed at 1.23V. Forcing a 50µA current into this pin, the
built in oscillator stops to switch.
6/34
L6911E
Electrical data
3
Electrical data
3.1
Maximum ratings
Table 3. Absolute maximum ratings
Symbol
Parameter (1)
Value
Unit
V
Vcc
BOOT-VPHASE Boot Voltage
HGATE-VPHASE
Vcc to GND, PGND
15
15
V
V
V
15
V
OCSET, PHASE, LGATE
-0.3 to Vcc+0.3
V
V
V
ROSC, SS, FB, PGOOD, VSEN
COMP, OVP
7
6.5
1. ESD immunity for pins 2 to 9 and 18 to 20 is guaranteed up to 1500V (Human Body Model).
3.2
Thermal data
Table 4. Thermal data
Symbol
Parameter
Value
Unit
RthJA
Thermal resistance junction to ambient
110
°C/W
Tmax
TSTG
TJ
Maximum junction temperature
Storage temperature range
Junction temperature range
150
°C
°C
°C
-40 to 150
0 to 125
7/34
Electrical characteristics
L6911E
4
Electrical characteristics
Table 5. Electrical characteristic (VCC = 12V; TA = 25°C unless otherwise specified)
Symbol
Parameter
Test condition
Min
Typ
Max
Unit
VCC supply current
Icc
Vcc supply current
UGATE and LGATE open
5
mA
Power-ON
Turn-On VCC threshold
Turn-Off VCC threshold
Rising VOCSET threshold
Soft start current
VOCSET = 4.5V
VOCSET = 4.5V
4.6
V
V
3.6
1.26
10
V
ISS
µA
Oscillator
Free running frequency
Total Variation
RT = OPEN
180
-15
200
1.9
220
15
kHz
ꢀ
6 KΩ < RT to GND < 200 KΩ
∆VOSC Ramp amplitude
RT = OPEN
Vp-p
Reference and DAC
DACOUT voltage accuracy
VID0, VID1,VID2, VID3, VID25mV
see Table 6 on page 9;
TA = 0 to 70°C
-1
1
ꢀ
VID Pull-Up voltage
Error amplifier
3.1
V
DC gain
88
15
10
dB
GBWP Gain-bandwidth product
MHz
V/µS
SR
Slew-rate
COMP = 10pF
Gate drivers
IUGATE High side source current
VBOOT - VPHASE = 12V,
VUGATE - VPHASE = 6V
1
1.3
2
A
RUGATE High side sink resistance
VBOOT - VPHASE = 12V,
IUGATE = 300mA
4
3
Ω
ILGATE
Low side source current
VCC = 12V, VLGATE = 6V
Vcc=12V, ILGATE = 300mA
PHASE connected to GND
0.9
1.1
1.5
A
Ω
RLGATE Low side sink resistance
Output driver dead time
Protections
120
nS
Over voltage trip (VSEN/DACOUT) VSEN rising
IOCSET OCSET current source VOCSET = 4.5V
117
200
120
230
ꢀ
170
µA
8/34
L6911E
Electrical characteristics
Table 5. Electrical characteristic (VCC = 12V; TA = 25°C unless otherwise specified) (continued)
Symbol
Parameter
Test condition
Min
Typ
Max
Unit
IOVP
OVP sourcing current
VSEN > OVP trip, VOVP = 0V
60
mA
Power GOOD
Upper threshold
VSEN rising
108
88
110
90
2
112
92
ꢀ
ꢀ
ꢀ
V
(VSEN/DACOUT)
Lower threshold
(VSEN/DACOUT)
VSEN falling
Hysteresis
(VSEN/DACOUT)
Upper and lower threshold
IPGOOD = -5mA
VPGOOD PGOOD voltage low
0.5
4.1
VID Setting
Table 6. VID Setting
VID4
(25mV)
Output
VID4
(25mV)
Output
VID3 VID2 VID1 VID0
VID3 VID2 VID1 VID0
Voltage (V)
1.050
1.075
1.100
1.125
1.150
1.175
1.200
1.225
1.250
1.275
1.300
1.325
1.350
1.375
1.400
1.425
Voltage (V)
1.450
1.475
1.500
1.525
1.550
1.575
1.600
1.625
1.650
1.675
1.700
1.725
1.750
1.775
1.800
1.825
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
9/34
Device description
L6911E
5
Device description
The device is an integrated circuit realized in BCD technology. It provides complete control
logic and protections for a high performance step-down DC-DC converter optimized for
microprocessor power supply. It is designed to drive N Channel Mosfets in a synchronous-
rectified buck topology. The device works properly with Vcc ranging from 5V to 12V and
regulates the output voltage starting from a 1.26V power stage supply voltage (Vin). The
output voltage of the converter can be precisely regulated, programming the VID pins, from
1.050V to 1.825V with 25mV binary steps, with a maximum tolerance of 1ꢀ over
temperature and line voltage variations. The device provides voltage-mode control with fast
transient response. It includes a 200kHz free-running oscillator that is adjustable from
50kHz to 1MHz. The error amplifier features a 15MHz gain-bandwidth product and 10V/ms
slew rate which permits high converter bandwidth for fast transient performance. The
resulting PWM duty cycle ranges from 0ꢀ to 100ꢀ. The device protects against over-
current conditions entering in HICCUP mode. The device monitors the current by using the
r
of the upper MOSFET which eliminates the need for a current sensing resistor.
ds(ON)
The device is available in SO20 package.
5.1
Oscillator
The switching frequency is internally fixed to 200kHz. The internal oscillator generates the
triangular waveform for the PWM charging and discharging with a constant current an
internal capacitor. The current delivered to the oscillator is tipically 50µA (F
= 200KHz)
SW
and may be varied using an external resistor (R ) connected between RT pin and GND or
T
VCC. Since the RT pin is maintained at fixed voltage (typ. 1.235V), the frequency is varied
proportionally to the current sinked (forced) from (into) the pin.
In particular connecting it to GND the frequency is increased (current is sinked from the pin),
according to the following relationship:
Equation 1
4.94 ⋅ 106
fS = 200kHz + -------------------------
RT(kΩ)
10/34
L6911E
Device description
Connecting R to V = 12V or to V = 5V the frequency is reduced (current is forced into
T
CC
CC
the pin), according to the following relationships:
Equation 2
4.306 ⋅ 107
fS = 200kHz + ----------------------------
RT(kΩ)
VCC = 12V
Equation 3
15 ⋅ 107
RT(kΩ)
fS = 200kHz + --------------------
VCC = 5V
Switching frequency variations vs. R are reported in Figure 3 on page 11.
T
Note:
That forcing a 50µA current into this pin, the device stops switching because no current is
delivered to the oscillator.
Figure 3. Switching frequency variations vs. R
T
10000
1000
100
RT to GND
10
RT to VCC=12V
RT to VCC=5V
10
100
1000
Frequency [kHz]
11/34
Device description
L6911E
5.2
Digital to analog converter
The built-in digital to analog converter allows the adjustment of the output voltage from
1.050V to 1.825V with 25mV binary steps as shown in the previous Table 6: VID Setting on
page 9. The internal reference is trimmed to ensure the precision of 1ꢀ.
The internal reference voltage for the regulation is programmed by the voltage identification
(VID) pins. These are TTL compatible inputs of an internal DAC that is realised by means of
a series of resistors rpoviding a partition of the internal voltage reference. The VID code
drives a multiplexer that selects a voltage on a precise point of the divider. The DAC output
is delivered to an amplifier obtaining the VPROG voltage reference (i.e. the set-point of the
error amplifier). Internal pull-ups are provided (realized with a 5µA current generator); in this
way, to program a logic "1" it is enough to leave the pin floating, while to program a logic "0"
it is enough to short the pin to GND.
The voltage identification (VID) pin configuration also sets the power-good thresholds
(PGOOD) and the over- voltage protection (OVP) thresholds.
5.3
Soft start and inhibit
At start-up a ramp is generated charging the external capacitor C by means of a 10µA
SS
constant current, as shown in Figure 4 on page 13
When the voltage across the soft start capacitor (V ) reaches 0.5V the lower power MOS is
SS
turned on to discharge the output capacitor. As V reaches 1V (i.e. the oscillator triangular
SS
wave inferior limit) also the upper MOS begins to switch and the output voltage starts to
increase.
The VSS growing voltage initially clamps the output of the error amplifier, and consequently
VOUT linearly increases, as shown in Figure 4 on page 13. In this phase the system works
in open loop. When VSS is equal to VCOMP the clamp on the output of the error amplifier is
released. In any case another clamp on the non-inverting input of the error amplifier remains
active, allowing to VOUT to grow with a lower slope (i.e. the slope of the VSS voltage, see
Figure 4 on page 13). In this second phase the system works in closed loop with a growing
reference. As the output voltage reaches the desired value VPROG, also the clamp on the
error amplifier input is removed, and the soft start finishes. Vss increases until a maximum
value of about 4V.
The Soft-Start will not take place, and the relative pin is internally shorted to GND, if both
VCC and OCSET pins are not above their own Turn-On thresholds; in this way the device
starts switching only if both the power supplies are present. During normal operation, if any
under-voltage is detected on one of the two supplies, the SS pin is internally shorted to GND
and so the SS capacitor is rapidly discharged.
The device goes in INHIBIT state forcing SS pin below 0.4V. In this condition both external
MOSFETS are kept OFF.
12/34
L6911E
Device description
Figure 4. Soft start
Vcc Turn-on threshold
Vin Turn-on threshold
Vcc
Vin
1V
Vss
to GND
0.5V
LGATE
Vout
Timing diagram
Aquisition: CH1 = PHASE; CH2 = VOUT
;
CH3 = PGOOD; CH4 = VSS
CH3 = PGOOD; CH4 = V
SS
5.4
Driver section
The driver capability on the high and low side drivers allows to use different types of power
MOS (also multiple MOS to reduce the R ), maintaining fast switching transition.
ds(ON)
The low-side mos driver is supplied directly by Vcc while the high-side driver is supplied by
the BOOT pin.
Adaptative dead time control is implemented to prevent cross-conduction and allow to use
many kinds of mosfets. The upper mos turn-on is avoided if the lower gate is over about
200mV while the lower mos turn-on is avoided if the PHASE pin is over about 500mV. The
upper mos is in any case turned-on after 200nS from the low side turn-off.
The peak current is shown for both the upper (Figure 5 on page 14) and the lowr (Figure 6
on page 14) driver at 5V and 12V. a 4nF capacitive load has been used in these
measurements.
For the lower driver, the source peak current is 1.1A @ V = 12V and 500mA @ V = 5V,
CC
CC
and the sink peak current is 1.3A @ V = 12V and 500mA @ V = 5V.
CC
CC
Similary, for the upper driver, the source peak current is 1.3A @ Vboot-Vphase = 12V and
600mA @ Vboot-Vphase = 5V, and the sink peak current is 1.3A @ Vboot-Vphase = 12V
and 550mA @ Vboot-Vphase = 5V.
13/34
Device description
L6911E
Figure 5. High side driver peak current, Vboot-Vphase=12V (left) Vboot-Vphase=5V
(right) CH1 = High Side Gate CH4 = inductor current
Figure 6. Low side driver peak current,
V
=12V (left) V =5V (right)CH1 = Low side gate CH4 = inductor current
CC
CC
14/34
L6911E
Device description
5.5
Monitor and protection
The output voltage is monitored by means of pin 1 (VSEN). If it is not within 10ꢀ (typ.) of
the programmed value, the powergood output is forced low.
The device provides overvoltage protection, when the output voltage reaches a value 17ꢀ
(typ.) greater than the nominal one. If the output voltage exceed this threshold, the OVP pin
is forced high (5V) and the lower driver is turned on as long as the over-voltage is detected.
The OVP pin is capable to deliver up to 60mA (min) in order to trigger an external SCR
connected to burn the input fuse. The low-side mosfet turn-on implement this function when
the SCR is not used and helps in keeping the ouput low.
To perform the overcurrent protection the device compares the drop across the high side
MOS, due to its
RDSON, with the voltage across the external resistor (R
) connected between the
OCS
OCSET pin and drain of the upper MOS. Thus the overcurrent threshold (I ) can be
P
calculated with the following relationship:
Equation 4
I
⋅ ROCS
IP = --O----C----S----------------------
RDSON
where the typical value of I
is 200µA.
OCS
To calculate the R
value it must be considered the maximum R
(also the variation
OCS
DSON
with temperature) and the minimum value of I
. To avoid undesirable trigger of
OCS
overcurrent protection this relationship must be satisfied:
Equation 5
∆l
IP ≥ IOUTMAX + ---- = IPEAK
2
where ∆I is the inductance ripple current and I
is the maximum output current.
OUTMAX
In case of output short circuit the soft start capacitor is discharged with constant current
(10µA typ.) and when the SS pin reaches 0.5V the soft start phase is restarted. During the
soft start the over-current protection is always active and if such kind of event occours, the
device turns off both mosfets, and the SS capacitor is dicharged again after reaching the
upper threshold of about 4V. The system is now working in HICCUP mode, as shown in
Figure 7 on page 16 a. After removing the cause of the over-current, the device restart
working normally without power supplies turn off and on.
15/34
Device description
Figure 7. Hiccup mode and Inductor ripple current vs. V
L6911E
OUT
9
8
7
6
5
4
3
2
1
0
L=1.5 H, Vin=12V
µ
L=2 H,
Vin=12V
µ
L=3µH,
Vin=12V
L=1.5 H,
Vin=5V
µ
L=2 H,
µ
Vin=5V
L=3 H, Vin=5V
µ
0.5
1.5
2.5
3.5
Output Voltage [V]
a)
b)
5.6
Inductor design
The inductance value is defined by a compromise between the transient response time, the
efficiency, the cost and the size. The inductor has to be calculated to sustain the output and
the input voltage variation to maintain the ripple current ∆I between 20ꢀ and 30ꢀ of the
L
maximum output current. The inductance value can be calculated with this relationship:
Equation 6
V
IN – VOUT VOUT
----------------------------- --------------
L =
⋅
fs ⋅ ∆IL
VIN
Where f
is the switching frequency, V is the input voltage and V
is the output
SW
IN
OUT
voltage. Figure 7 b shows the ripple current vs. the output voltage for different values of the
inductor, with vin = 5V and Vin = 12V.
Increasing the value of the inductance reduces the ripple current but, at the same time,
reduces the converter response time to a load transient. If the compensation network is well
designed, the device is able to open or close the duty cycle up to 100ꢀ or down to 0ꢀ. The
response time is now the time required by the inductor to change its current from initial to
final value. Since the inductor has not finished its charging time, the output current is
supplied by the output capacitors. Minimizing the response time can minimize the output
capacitance required.
The response time to a load transient is different for the application or the removal of the
load: if during the application of the load the inductor is charged by a voltage equal to the
difference between the input and the output voltage, during the removal it is discharged only
by the output voltage. The following expressions give approximate response time for ∆I load
transient in case of enough fast compensation network response:
16/34
L6911E
Device description
Equation 7
Equation 8
L ⋅ ∆I
tapplication = -----------------------------
V
IN – VOUT
L ⋅ ∆I
tremoval = --------------
VOUT
The worst condition depends on the input voltage available and the output voltage selected.
Anyway the worst case is the response time after removal of the load with the minimum
output voltage programmed and the maximum input voltage available.
5.7
Output capacitor
Since the microprocessors require a current variation beyond 10A doing load transients,
with a slope in the range of tenth A/µsec, the output capacitor is a basic component for the
fast response of the power supply. In fact for first few microseconds they supply the current
to the load. The controller recognizes immediately the load transient and sets the duty cycle
at 100ꢀ, but the current slope is limited by the inductor value.
The output voltage has a first drop due to the current variation inside the capacitor
(neglecting the effect of the ESL):
Equation 9
∆VOUT = ∆IOUT · ESR
A minimum capacitor value is required to sustain the current during the load transient
without discharge it. The voltage drop due to the output capacitor discharge is given by the
following equation:
Equation 10
∆I2OUT
∆VOUT = -------------------------------------------------------------------------------------------
2 ⋅ COUT ⋅ (VINMIN ⋅ DMAX – VOUT
L
)
Where D
is the maximum duty cycle value that is 100ꢀ. The lower is the ESR, the lower
MAX
is the output drop during load transient and the lower is the output voltage static ripple.
17/34
Device description
L6911E
5.8
Input capacitor
The input capacitor has to sustain the ripple current produced during the on time of the
upper MOS, so it must have a low ESR to minimize the losses.
The rms value of this ripple is:
Equation 11
Irms = IOUT D ⋅ (1 – D)
Where D is the duty cycle. The equation reaches its maximum value with D = 0.5.
The losses in worst case are:
Equation 12
P = ESR ⋅ Ir2ms
5.9
Compensation network design
The control loop is a voltage mode (Figure 9 on page 19) that uses a droop function to
satisfy the requirements for a VRM module, reducing the size and the cost of the output
capacitor.
This method "recovers" part of the drop due to the output capacitor ESR in the load
transient, introducing a dependence of the output voltage on the load current: at light load
the output voltage will be higher than the nominal level, while at high load the output voltage
will be lower than the nominal value.
Figure 8. Output transient response without (a) and with (b) the droop function
18/34
L6911E
Device description
As shown in Figure 8 on page 18, the ESR drop is present in any case, but using the droop
function the total deviation of the output voltage is minimized. In practice the droop function
introduces a static error (Vdroop in Figure 8 on page 18) proportional to the output current.
Since a sense resistor is not present, the output DC current is measured by using the
intrinsic resistance of the inductance (a few mΩ). So the low-pass filtered inductor voltage
(that is the inductor current) is added to the feedback signal, implementing the droop
function in a simple way. Referring to the schematic in Figure 9, the static characteristic of
the closed loop system is:
Equation 13
RL ⋅ R8 // R9
R3 + R8 // R9
----------------------------------
VOUT = VPROG + VPROG ⋅ ------------------------------------ –
⋅ IOUT
R8
R2
Where V
is the output voltage of the digital to analog converter (i.e. the set point) and
PROG
R is the inductance resistance. The second term of the equation allows a positive offset at
L
+
zero load (∆V ); the third term introduces the droop effect (∆V
). Note that the droop
DROOP
effect is equal the ESR drop if:
Equation 14
RL ⋅ R8 // R9
---------------------------------- = ESR
R8
Figure 9. Compensation network
V IN
V
C O
M
P
V
P H A S E
L 2
R
L
V
O U T
P W M
E S R
R 8
C 1 8
Z F
C 6 -1 5
C 2 0
R 4
R 9
R 3
C 2 5
V
P R O
G
Z I
R 2
19/34
Device description
L6911E
Considering the previous relationships R2, R3, R8 and R9 may be determined in order to
obtain the desired droop effect as follow:
●
Choose a value for R2 in the range of hundreds of KΩ to obtain realistic values for the
other components.
●
From the above equations, it results:
Equation 15
∆V+ ⋅ R2
---------------------- -------------------------
RL ⋅ IMAX
R8 =
⋅
VPROG ∆VDROOP
Equation 16
∆VDROOP
1
------------------------- -----------------------------------
R9 = R8 ⋅
⋅
RL ⋅ IMAX
∆VDROOP
1 + -------------------------
RL ⋅ IMAX
Where I
is the maximum output current.
MAX
●
The component R3 must be chosen in order to obtain R3 << R8//R9 to permit these
and successive simplifications.
Therefore, with the droop function the output voltage decreases as the load current
increases, so the DC output impedance is equal to a resistance R . It is easy to verify that
OUT
the output voltage deviation under load transient is minimum when the output impedance is
constant with frequency.
20/34
L6911E
Device description
To choose the other components of the compensation network, the transfer function of the
voltage loop is considered. To simplify the analysis is supposed that R3 << Rd,
where Rd = (R8//R9).
Figure 10. Compensation network definition
|A v|
2
fLC
fC E
fE C
fC C
f
f
f
|R |
R
0
fD
f2
f1
f3
|G loop|
G 0
fc
Compensati onNetworkS ingularity
f
= 1 / 2π ⋅ R 4 ⋅ C20
= 1 / 2π ⋅ (R3 + R 4) ⋅ C 20
= 1 / 2π ⋅ R3 ⋅ C 25
ConverterS ingularity
f
f
= 1/ 2π
⋅
LC
doublepole
ESRzero
1
LC
f
f
f
= 1/ 2π ⋅ ESR ⋅ C
2
3
d
CE
OUT
= 1 / 2π ⋅ ESR ⋅ Cceramic
f
Introduced by
EC
= 1 / 2π ⋅ Rd ⋅ C 25
f
= 1 / 2π ⋅ Rceramic ⋅ Cceramic
CeramicCap acitor
CC
The transfer function may be evaluated neglecting the connection of R8 to PHASE because,
as will see later, this connection is important only at low frequencies. So R4 is considered
connected to VOUT. Under this assumption, the voltage loop has the following transfer
function:
Equation 17
ZC(s)
--------------- ------------------------------------
Zf(s)
Zi(s)
Vin
-------------
Gloop(s) = Av(s) ⋅ R(s) = Av(s) ⋅
where
Av(s) =
⋅
∆Vosc ZC(s) + ZL(s)
Where Z (s) and Z (s) are the output capacitor and inductor impedance respectively.
C
L
The expression of Z (s) may be simplified as follow:
I
21/34
Device description
Equation 18
L6911E
2 R3
R3
1
s
⎛
⎞
⎛
⎝
⎞
1
s
⎛
⎝
⎞
-------
-------
Rd 1 + s ⋅ (τ1 + τd) + s ⋅
⋅ τ1 ⋅ τd
1 + s
⋅ τd ⋅ (1
--
R4 + ⋅ C20 ⋅ R3
--
Rd ⋅ ⋅ C25
⎝
⎠
⎠
Rd
Rd
⎠
-------------------------------------------------------------------------------------------------
----------------------------------------------
--------------------------------- + ----------------------------------------------------- =
= Rd
(1 + s ⋅ τ2) ⋅ (1 + s ⋅ τd)
(1 + s ⋅ τ2) ⋅ (1 +
1
1
⎛
⎞
Rd + -- ⋅ C25
--
R4 + ⋅ C20 + R3
s
⎝
⎠
s
Where: τ = R4 × C20, τ = (R4+R3) × C20 and τ = Rd × C25.
1
2
d
The regulator transfer function became now:
Equation 19
(1 + s ⋅ τ2) ⋅ (1 + s ⋅ τd)
-------------------------------------------------------------------------------------------------------
R(s) ≈
R3
⎛
⎞
-------
s ⋅ C18 ⋅ Rd ⋅ 1 + s
⋅ τd ⋅ (1 + s ⋅ τ1)
⎝
⎠
Rd
Figure 10 on page 21 shows a method to select the regulator components (please note that
the frequencies f and f corresponds to the singularities introduced by additional
EC
CC
ceramic capacitors in parallel to the output main electrolytic capacitor).
To obtain a flat frequency response of the output impedance, the droop time constant
τ has to be equal to the inductor time constant (see the note at the end of the section):
●
d
Equation 20
L
RL
L
τd = Rd ⋅ C25 = ------ = τL
⇒ C25 = -----------------------
(RL ⋅ Rd)
●
To obtain a constant -20dB/dec Gloop(s) shape the singularity f and f are placed in
1
2
proximity of f and f respectively. This implies that:
CE
LC
Equation 21
fLC
--------
fCE
f2
fLC
⎛
⎞
--- =
f1
⇒
R4 = R3 ⋅ -------- – 1
⎝
⎠
fCE
1
2
--
f1= fCE
⇒
C20
=
⋅ π ⋅ R4 ⋅ fCE
●
To obtain a Gloop bandwidth of f , results:
C
Equation 22
fC
VIN C20 // C25
----------------- ----------------------------
VIN
C20 ⋅ C25
-------
----------------- ----------------------------
⋅
fLC = 1 ⋅ fC
⇒
G0 = A0 ⋅ R0
=
⋅
=
⇒ C18 =
∆Vosc
C18
fLC
∆Vosc C20 + C25
22/34
L6911E
Device description
Note:
To understand the reason of the previous assumption, the scheme in Figure 11 on page 23
must be considered.
In this scheme, the inductor current has been substituted by the load current, because in the
frequencies range of interest for the Droop function these current are substantially the same
and it was supposed that the droop network don't represent a charge for the inductor.
Figure 11. Voltage regulation with droop function block scheme
Vcomp
Vout
Av(s)
R(s)
Iout
It results:
Equation 23
1 + sτL
GLOOP
1 + sτL
-----------------
1 + sτd
Vo
ZOUT = --------------- = Rd ⋅
----------------- ----------------------------
⋅
= ROUT ⋅
1 + sτd 1 + GLOOP
ILOAD
Because in the interested range |Gloop|>>1.
To obtain a flat shape, the relationship considered will naturally follow.
23/34
VRM demo board description
L6911E
6
VRM demo board description
Figure 12 shows the schematic circuit of the VRM evaluation board. The design has been
developed for a VRM 8.5 Flexible Motherboard applicaton delivering up to 28.5A.
An additional circuit sense a Vtt bus (1.2V typ.) and generate a 2.5mS (typ.) delayed
Vtt_PWRGD signal when this rail is over 1.1V. The assertion of the Vtt_PWRGD signal
enables the device together with the ENOUT input.
Figure 12. Schematic circuit
L1
F1
+5 VIN
D1
C10
R7
C1-3
C11
+12Vcc
15
19
R14
VCC
GND
VID0
VID1
VID2
VID3
VID4
OSC
SS
OCSET
18
11
4
2
C12
UGATE
PHASE
LGATE
PGND
14
13
VID0
Q1,Q2
L2
VID1
VOUTCORE
Vss
5
VID2
U1
VID3
L6911E17
Q3,Q4,Q5
D2
C4-9
R15
R6
6
7
16
VID25mV
8
PGOOD
VSEN
R1
12
PWRGD
20
3
1
9
10
C13
R8
C18
Q7
R3
R4
R9
C20
C17
C19
R5
C14
Vdd
RESET
5
R2
6
8
2
NOT RESET
NOT RESIN
GND
UZ
D3
Vtt_PGOOD
TLC7701
4
CT
3
Vtt_sense
SENSE
R13
7
1
C15
C16
CONTROL
L6911E CONNECTOR EVALUATION KIT REV. 1.1
OUTEN
R10
R12
Q6
R11
24/34
L6911E
VRM demo board description
6.1
Efficiency
The measured efficiency versus load current at different output voltages is shown in
Figure 13. In the application two Mosfets STS12NF30L (30V, 8.5mΩ typ with V = 12V)
GS
connected in parallel are used for the High Side, while three of them are used for the Low
Side.
Figure 13. Efficiency vs. load current
90
80
70
Vout = 1.825V
60
Vout = 1.225V
50
40
Vout = 1.500V
0
5
10
15
20
25
Output Current [A]
6.2
6.3
Inductor design
Since the maximum output current is 28.5A, to have a 20ꢀ ripple (5A) the inductor chosen
is 1.5µH.
Output capacitor
In the demo six OSCON capacitors, model 6SP680M, are used, with a maximum ESR equal
to 12mΩ each. Therefore the resultant ESR is of 2mΩ. For load transient of 28.5A in the
worst case the voltage drop is of:
Equation 24
∆Vout = 28.5 * 0.002 = 57mV
The voltage drop due to the capacitor discharge during load transient, considering that the
maximum duty cicle is equal to 100ꢀ results in 46.5mV with 1.85V of programmed output.
25/34
VRM demo board description
L6911E
6.4
Input capacitor
For I
= 28.5A and with D = 0.5(worst case for input current ripple), Irms is equal to 17.8A.
OUT
Three OSCON electrolityc capacitors 6SP680M, with a maximum ESR equal to 12mΩ, are
chosen to substain the ripple. So the losses in worst case are:
Equation 25
P = ESR ⋅ Ir2ms = (1.25(670)m)W
6.5
Over-current protection
Substituting the demo board parameters in the relationship reported in the relative section,
(I
= 170µA; I =33A; R
= 3mΩ) it results that R
= 1kΩ.
OCSMIN
P
DSONMAX
OCS
26/34
L6911E
Connector pin orientation
7
Connector pin orientation
Table 7. Connector pin orientation
Pin #
1
Row A
5Vin
Pin #
50
49
48
47
46
45
44
43
42
41
40
39
Row B
5Vin
2
5Vin
5Vin
3
5Vin
5Vin
4
5Vin
5Vin
5
12Vin
12Vin
12Vin
No Contact
VID1
6
12Vin
7
Reserved
VID0
8
9
VID2
VID3
10
11
12
VID4 (25mV)
OUTEN
VTT_PWRGD
PWRGD
Ishare
VTT
13
14
Vss
38
37
Vss
Vss
VccCORE
15
VccCORE
36
VccCORE
16
17
Vss
35
34
Vss
VccCORE
VccCORE
Mechanical Key
18
19
Vss
33
32
Vss
VccCORE
VccCORE
20
21
Vss
31
30
Vss
VccCORE
VccCORE
22
23
Vss
29
28
Vss
VccCORE
VccCORE
24
25
Vss
27
26
Vss
VccCORE
VccCORE
27/34
PCB and components layout
L6911E
8
PCB and components layout
Figure 14. PCB and components layouts
Component side silkscreen
Component side
Figure 15. PCB and components layouts
Internal Layer
Internal Ground Plane
Figure 16. PCB and components layouts
Solder Side
Solder Side Silkscreen
28/34
L6911E
PCB and components layout
Table 8. Part list
Resistors
R1
R2
Not Mounted
470K
1K
SMD 0805
SMD 0805
SMD 0805
SMD 0805
SMD 0805
SMD 0805
SMD 0805
SMD 0805
SMD 0805
SMD 0805
SMD 0805
SMD 0805
SMD 0805
SMD 0805
SMD 0805
1ꢀ
R3
R4
82
R5
Not Mounted
20K
R6
R7
680
R8
13K
R9
100K
6.8K
10K
R10
R11
R12
R13
R14
R15
1ꢀ
1ꢀ
1K
10K
8.2Ω
1K
Capacitors
C1-C3
C4-C9
680µF- 6.3V
OSCON 6SP680M
Radial 10x10.5
820 µF – 4V or
680µF – 6.3V
OSCON 4SP820M
OSCON 6SP680M
Radial 10x10.5
Radial 10x10.5
C10
C11,C13-C16
C12
1nF
100nF
1µF
SMD 0805
SMD 0805
SMD 0805
SMD 0805
SMD 0805
SMD 0805
SMD 0805
C17
47nF
C18
3.3nF
C19
Not Mounted
100nF
C20
Magnetics
L1
L2
1.5µH
1.8µH
T44-52 Core, 7T - 18AWG
T50-52B Core, 8T – 16AWG
Transistors
Q1-Q5
STS12NF30L or
FDS6670
STMicroelectronics
Fairchild
SO8
SO8
Q6
Q7
Signal NPN BJT
Signal MOSFET
SOT23
SOT23
29/34
PCB and components layout
Table 8. Part list (continued)
L6911E
Diodes
D1
D2
D3
1N4148
SOT23
STPS3L25U
STMicroelectronics
SMB
Ics
U1
U2
L6911E
STMicroelectronics
Texas Instruments
SO20
SO8
TLC7701QD
Fuse
F1
251015A-15A
Littlefuse
AXIAL
30/34
L6911E
Package mechanical data
9
Package mechanical data
In order to meet environmental requirements, ST offers these devices in ECOPACK®
packages. These packages have a Lead-free second level interconnect . The category of
second level interconnect is marked on the package and on the inner box label, in
compliance with JEDEC Standard JESD97. The maximum ratings related to soldering
conditions are also marked on the inner box label. ECOPACK is an ST trademark.
ECOPACK specifications are available at: www.st.com
31/34
Package mechanical data
Figure 17. SO20 Mechanical data & package dimensions
L6911E
mm
inch
DIM.
OUTLINE AND
MECHANICAL DATA
MIN. TYP. MAX. MIN.
TYP. MAX.
0.104
A
A1
B
2.35
0.10
0.33
0.23
12.60
2.65 0.093
0.30 0.004
0.51 0.013
0.32 0.009
13.00 0.496
0.012
0.200
C
0.013
(1)
D
0.512
E
e
7.40
7.60 0.291
0.299
0.050
1.27
H
10.0
0.25
0.40
10.65 0.394
0.75 0.010
1.27 0.016
0˚ (min.), 8˚ (max.)
0.10
0.419
h
0.030
L
0.050
k
ddd
0.004
SO20
(1) “D” dimension does not include mold flash, protusions or gate
burrs. Mold flash, protusions or gate burrs shall not exceed
0.15mm per side.
0016022 D
32/34
L6911E
Revision history
10
Revision history
Table 9. Revision history
Date
Revision
Changes
15-Nov-2001
10-Apr-2007
2
3
Preliminary version
Document has been reformatted, updated Table 3.
33/34
L6911E
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2007 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
34/34
相关型号：
©2020 ICPDF网 联系我们和版权申明