LD39015JXX12 [STMICROELECTRONICS]
150 mA low quiescent current low noise voltage regulator;型号: | LD39015JXX12 |
厂家: | ST |
描述: | 150 mA low quiescent current low noise voltage regulator |
文件: | 总17页 (文件大小:505K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LD39015Jxx
150 mA low quiescent current
low noise voltage regulator
Features
■ Input voltage from 1.5 to 5.5 V
■ Ultra low dropout voltage (90 mV typ. at 100
mA load)
■ Very low quiescent current (20 µA typ. at no
load, 35 µA typ. at 150 mA load, 1 µA max in off
mode)
■ Low noise (54 µV
from 10 Hz to 100 kHz at
Flip-chip 4
RMS
V
= 1.8 V)
OUT
■ Output voltage tolerance: 2.0% @ 25 °C
■ 150 mA guaranteed output current
74 dB at low frequencies and starts to roll off at 10
kHz. Enable logic control function puts the
LD39015Jxx in shut-down mode allowing a total
current consumption lower than 1 µA. The device
also includes a short-circuit constant current
limiting and thermal protection. Typical
■ Wide range of output voltages available on
request: 0.8 V to 4.5 V with 100 mV step
■ Logic-controlled electronic shutdown
■ Compatible with ceramic capacitor
applications are mobile phones, personal digital
assistant (PDAs), cordless phone and similar
battery powered systems.
C
= 1 µF
OUT
■ Internal current and thermal limit
■ Flip-chip 4 bumps 1.1 x 1.1 mm.
■ Temperature range: -40 °C to 125 °C
Description
The LD39015Jxx provides 150 mA maximum
current from an input voltage ranging from 1.5 V
to 5.5 V with a typical dropout voltage of 80 mV. It
is stable with ceramic capacitor. The ultra low
drop-voltage, low quiescent current and low noise
features make it suitable for low power battery
powered applications. Power supply rejection is
Table 1.
Device summary
Part numbers
Order codes
Output voltages
LD39015JXX12
LD39015JXX13
LD39015JXX15
LD39015JXX18
LD39015JXX28
LD39015J12R
LD39015JJ13R
LD39015J15R
LD39015J18R
LD39015J28R
1.2 V
1.3 V
1.5 V
1.8 V
2.8 V
August 2009
Doc ID 15968 Rev 2
1/17
www.st.com
17
Contents
LD39015Jxx
Contents
1
2
3
4
5
6
7
8
Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Typical application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Typical performance characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Different output voltage versions of the LD39015Jxx
available on request . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
9
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2/17
Doc ID 15968 Rev 2
LD39015Jxx
1
Diagram
Diagram
Figure 1.
Block diagram
OUT
IN
BandGap
1.22 V
R1
R2
Trimming
Thermal
Protection
Enable
EN
GND
Doc ID 15968 Rev 2
3/17
Pin configuration
LD39015Jxx
2
Pin configuration
Figure 2.
Pin connection (top view)
Table 2.
Pin description
Symbol
Pin n°
Function
A2
A1
B2
B1
EN
GND
IN
Enable pin logic input: Low=shutdown, High=active
Common ground
Input voltage of the LDO
Output voltage
OUT
4/17
Doc ID 15968 Rev 2
LD39015Jxx
3
Typical application
Typical application
Figure 3.
Typical application circuit
VOUT
Load
VIN
IN
OUT
1 µF
1 µF
EN
GND
VEN
Doc ID 15968 Rev 2
5/17
Maximum ratings
LD39015Jxx
4
Maximum ratings
Table 3.
Absolute maximum ratings
Parameter
Symbol
Value
Unit
VIN
VOUT
VEN
IOUT
PD
DC input voltage
- 0.3 to 6
- 0.3 to VI + 0.3
- 0.3 to VI + 0.3
Internally limited
Internally limited
-65 to 150
V
V
DC output voltage
Enable input voltage
Output current
V
mA
mW
°C
°C
Power dissipation
TSTG
TOP
Storage temperature range
Operating junction temperature range
-40 to 125
Note:
Absolute maximum ratings are those values beyond which damage to the device may occur.
Functional operation under these conditions is not implied. All values are referred to GND.
Table 4.
Symbol
RthJA
Thermal data
Parameter
Value
Unit
Thermal resistance junction-ambient
180
°C/W
6/17
Doc ID 15968 Rev 2
LD39015Jxx
Electrical characteristics
5
Electrical characteristics
T = 25 °C, V = V
+ 1 V, C = C
= 1 µF, I
= 1 mA, V = V , unless
OUT EN IN
J
IN
OUT(NOM)
IN
OUT
otherwise specified.
Table 5.
Symbol
Electrical characteristics
Parameter
Test conditions
Min.
Typ.
Max.
Unit
VIN
Operating input voltage
Turn-on threshold
1.5
5.5
V
V
1.45
1.35
1.48
VUVLO
Turn-off threshold
1.30
-2.0
mV
VOUT > 1.5V, IOUT = 1mA, TJ = 25°C
OUT > 1.5V, IOUT = 1mA,
2.0
3.0
%
V
-3.0
-40°C < TJ < 125°C
VOUT VOUT accuracy
VOUT ≤ 1.5V, IOUT = 1mA
10
30
mV
VOUT ≤ 1.5V, IOUT = 1mA,
-40°C < TJ < 125°C
ΔVOUT Static line regulation
ΔVOUT Static load regulation
VOUT +1V ≤ VIN ≤ 5.5V, IOUT = 1mA
0.01
%/V
IOUT = 1mA to 150mA
0.002
%/mA
IOUT = 100mA, VOUT > 1.5V
-40°C < TJ < 125°C
VDROP Dropout voltage (1)
90
54
130
mV
10Hz to 100kHz, IOUT = 10mA, VOUT
= 1.8V, VIN = 2.8V
eN
Output noise voltage
µVRMS
VIN = VOUTNOM + 1V +/-VRIPPLE
VRIPPLE = 0.1V, freq. = 1kHz
IOUT = 10mA
74
Supply voltage rejection
VOUT = 1.5V
SVR
dB
µA
VIN = VOUTNOM + 0.5V +/-VRIPPLE
VRIPPLE = 0.1V, Freq.=10kHz
IOUT = 10mA
67
20
IOUT = 0mA
IOUT = 0mA, -40°C < TJ < 125°C
IOUT = 0 to 150mA
40
35
IQ
Quiescent current
I
OUT = 0 to 150mA
50
1
-40°C < TJ< 125°C
VIN input current in OFF MODE:
0.003
VEN = GND
ISC
Short circuit current
RL = 0
200
0.9
mA
V
VIN = 1.5V to 5.5V,
Enable input logic low
0.4
1
-40°C < TJ < 125°C
VEN
VIN = 1.5V to 5.5V,
-40°C < TJ < 125°C
Enable input logic high
V
IEN
Enable pin input current
Turn on time (2)
VSHDN = VIN, -40°C < TJ < 125°C
0.1
30
µA
µs
TON
Doc ID 15968 Rev 2
7/17
Electrical characteristics
LD39015Jxx
Table 5.
Symbol
Electrical characteristics (continued)
Parameter
Test conditions
Min.
Typ.
Max.
Unit
Thermal shutdown
Hysteresis
160
20
TSHDN
°C
Capacitance (see typical
performance characteristics for
stability)
COUT Output capacitor
1
22
µF
1. Dropout voltage is the input-to-output voltage difference at which the output voltage is 100 mV below its nominal value. This
specification does not apply for output voltages below 1.5 V.
2. Turn-on time is time measured between the enable input just exceeding VEN High Value and the output voltage just
reaching 95% of its nominal value.
8/17
Doc ID 15968 Rev 2
LD39015Jxx
Typical performance characteristics
6
Typical performance characteristics
Figure 4.
Output voltage vs. temperature
Figure 5.
Output voltage vs. input voltage
1.24
1.23
1.22
1.21
1.2
2
1.8
1.6
1.4
1.2
1
1 mA
150 mA
1.19
1.18
1.17
1.16
1.15
1.14
0.8
0.6
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
-75 -50 -25
0
25 50 75 100 125 150 175
VIN [V]
T [°C]
Figure 6.
Dropout voltage vs. output current Figure 7.
C
stability region
OUT
3
2.5
2
CI = 1 µF, VIN = VEN = VOUTNOM +1 to 5.5 V
IOUT=1 to 150mA
1.5
1
STABLE ZONE
0.5
0
0
5
10
15
20
COUT [µF] (nominal value)
Figure 8.
Supply voltage rejection vs.
frequency
Figure 9.
Output noise spectral density
Noise spectrum - VOUT(NOM) = 1.2V VIN=2.2V
1.4E-05
1.2E-05
1.0E-05
8.0E-06
6.0E-06
4.0E-06
2.0E-06
IOUT = 0A
IOUT = 1mA
IOUT = 10mA
IOUT = 100mA
0.0E+00
10
100
1000
10000
100000
f [Hz]
Doc ID 15968 Rev 2
9/17
Typical performance characteristics
Figure 10. SVR vs. drop
LD39015Jxx
Figure 11. Quiescent current vs. I
OUT
90
IQ versus IOUT
IOUT = 10 mA, VOUT = 1.8 V, ΔVIN = 0.3 V, f = 1kHz
40
85
80
75
70
65
60
35
30
25
20
15
10
5
0
0
10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0
0.5
1
1.5
2
2.5
3
3.5
4
IOUT [mA]
V
DROP(VIN - VOUT
)
Figure 12. Quiescent current vs. input voltage Figure 13. Load transient
IQ(GND) versus VIN
ILOAD = 1mA
35
ILOAD = 0
30
25
20
15
10
5
0
0
1
2
3
4
5
6
7
VIN [V]
IOUT = 10mA to 150mA, tr = tf = 5µs
Figure 14. Line transient
Figure 15. Enable transient
VIN = 1.5 V, VEN = 0 to 1 V, IOUT = 1 mA, CIN = COUT = 1 µF
IOUT = 10 mA; VOUT= 1.8 V; ΔVIN = 0.5 V; VIN = from 2.550
to 3.055V; Tr = Tf = 5 µs
10/17
Doc ID 15968 Rev 2
LD39015Jxx
Package mechanical data
7
Package mechanical data
In order to meet environmental requirements, ST offers these devices in different grades of
®
®
ECOPACK packages, depending on their level of environmental compliance. ECOPACK
specifications, grade definitions and product status are available at: www.st.com. ECOPACK
is an ST trademark.
Doc ID 15968 Rev 2
11/17
Package mechanical data
LD39015Jxx
Flip-chip 4 mechanical data
mm.
mils.
Dim.
Min.
Typ.
0.65
0.25
0.40
0.315
1.07
0.5
Max.
0.715
0.29
Min.
23.03
8.27
Typ.
25.59
9.84
Max.
28.15
11.42
A
A1
A2
b
0.585
0.21
15.75
12.40
42.13
19.69
42.13
19.69
9.84
0.265
1.02
0.365
10.43
14.37
44.09
D
1.12
40.15
D1
E
1.02
1.07
0.5
1.12
40.15
44.09
E1
SD
SE
0.25
0.25
9.84
7224716/G
12/17
Doc ID 15968 Rev 2
LD39015Jxx
Package mechanical data
Tape and reel Flip-chip 4 mechanical data
mm.
Typ.
inch.
Typ.
Dim.
Min.
Max.
178
Min.
Max.
6.926
0.519
A
C
12.8
20.2
59
13.2
0.504
0.795
2.323
D
N
60
61
8.4
2.362
2.401
0.331
0.048
0.048
0.031
0.161
0.161
T
Ao
Bo
Ko
Po
P
1.12
1.12
0.68
3.9
1.17
1.17
0.73
4
1.22
1.22
0.78
4.1
0.044
0.044
0.027
0.153
0.153
0.046
0.046
0.029
0.157
0.157
3.9
4
4.1
Doc ID 15968 Rev 2
13/17
Package mechanical data
Figure 16. Foot print data
LD39015Jxx
14/17
Doc ID 15968 Rev 2
LD39015Jxx
Different output voltage versions of the LD39015Jxx available on request
8
Different output voltage versions of the LD39015Jxx
available on request
Table 6.
Options available on request
Order codes
Output voltages
LD39015J08R
LD39015J10R
LD39015J33R
0.8 V
1.0 V
3.3 V
Doc ID 15968 Rev 2
15/17
Revision history
LD39015Jxx
9
Revision history
Table 7.
Document revision history
Revision
Date
Changes
29-Jun-2009
05-Aug-2009
1
2
First release.
Updated tape and reel mechanical data on page 13.
16/17
Doc ID 15968 Rev 2
LD39015Jxx
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2009 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
Doc ID 15968 Rev 2
17/17
相关型号:
©2020 ICPDF网 联系我们和版权申明