LD39015J [STMICROELECTRONICS]
150 mA low quiescent current low noise voltage regulator;型号: | LD39015J |
厂家: | ST |
描述: | 150 mA low quiescent current low noise voltage regulator |
文件: | 总16页 (文件大小:367K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LD39015J
150 mA low quiescent current low noise voltage regulator
Datasheet
-
production data
• Logic-controlled electronic shutdown
• Compatible with ceramic capacitor COUT = 1 µF
• Internal current and thermal limit
• Flip-chip 4 bumps 1.1 x 1.1 mm.
• Temperature range: -40 °C to 125 °C
Flip-chip 4
Description
The LD39015J provides 150 mA maximum
current from an input voltage ranging from 1.5 V
to 5.5 V with a typical dropout voltage of 90 mV. It
is stable with ceramic capacitor. The ultra low
drop-voltage, low quiescent current and low noise
features make it suitable for low power battery
powered applications. Power supply rejection is
74 dB at low frequencies and starts to roll off at 10
kHz. Enable logic control function puts the
LD39015J in shut-down mode allowing a total
current consumption lower than 1 µA. The device
also includes a short-circuit constant current
limiting and thermal protection. Typical
Features
• Input voltage from 1.5 to 5.5 V
• Ultra low dropout voltage (90 mV typ. at 100
mA load)
• Very low quiescent current (20 µA typ. at no
load, 35 µA typ. at 150 mA load, 1 µA max in off
mode)
• Low noise (54 µVRMS from 10 Hz to 100 kHz at
applications are mobile phones, personal digital
assistant (PDAs), cordless phone and similar
battery powered systems.
VOUT = 1.8 V)
• Output voltage tolerance: ± 2.0% @ 25 °C
• 150 mA guaranteed output current
• Wide range of output voltages available on
request: 0.8 V to 4.5 V with 100 mV step
Table 1. Device summary
Order codes
Output voltages
LD39015J12R
LD39015J15R
LD39015J18R
LD39015J25R
LD39015J28R
1.2 V
1.5 V
1.8 V
2.5 V
2.8 V
January 2014
DocID15968 Rev 4
1/16
This is information on a product in full production.
www.st.com
Contents
LD39015J
Contents
1
2
3
4
5
6
7
8
9
Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Typical application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Typical performance characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Packaging mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2/16
DocID15968 Rev 4
LD39015J
Diagram
1
Diagram
Figure 1. Block diagram
OUT
IN
BandGap
1.22 V
R1
R2
Trimming
Thermal
Protection
Enable
EN
GND
DocID15968 Rev 4
3/16
16
Pin configuration
LD39015J
2
Pin configuration
Figure 2. Pin connection (top view)
Table 2. Pin description
Pin n°
Symbol
Function
A2
A1
B2
B1
EN
GND
IN
Enable pin logic input: Low=shutdown, High=active
Common ground
Input voltage of the LDO
Output voltage
OUT
4/16
DocID15968 Rev 4
LD39015J
Typical application
3
Typical application
Figure 3. Typical application circuit
VOUT
Load
VIN
IN
OUT
1 µF
1 µF
EN
VEN
GND
DocID15968 Rev 4
5/16
16
Maximum ratings
LD39015J
4
Maximum ratings
Table 3. Absolute maximum ratings
Parameter
Symbol
Value
Unit
VIN
VOUT
VEN
IOUT
PD
DC input voltage
DC output voltage
Enable input voltage
Output current
- 0.3 to 6
- 0.3 to VI + 0.3
- 0.3 to VI + 0.3
Internally limited
Internally limited
-65 to 150
V
V
V
mA
mW
°C
°C
Power dissipation
TSTG
TOP
Storage temperature range
Operating junction temperature range
-40 to 125
Note:
Absolute maximum ratings are those values beyond which damage to the device may occur.
Functional operation under these conditions is not implied. All values are referred to GND.
Table 4. Thermal data
Symbol
RthJA
Parameter
Value
Unit
Thermal resistance junction-ambient
180
°C/W
6/16
DocID15968 Rev 4
LD39015J
Electrical characteristics
5
Electrical characteristics
TJ = 25 °C, VIN = VOUT(NOM) + 1 V, CIN = COUT = 1 µF, IOUT = 1 mA, VEN = VIN, unless
otherwise specified.
Table 5. Electrical characteristics
Symbol
Parameter
Test conditions
Min.
Typ.
Max.
Unit
VIN
Operating input voltage
Turn-on threshold
1.5
5.5
V
V
1.45
1.35
1.48
VUVLO
Turn-off threshold
1.30
-2.0
mV
VOUT > 1.5 V, IOUT = 1 mA,
TJ = 25 °C
2.0
3.0
%
VOUT > 1.5 V, IOUT = 1 mA,
-40 °C < TJ < 125 °C
-3.0
VOUT VOUT accuracy
VOUT ≤ 1.5 V, IOUT = 1 mA
10
30
mV
VOUT ≤ 1.5 V, IOUT = 1 mA,
-40 °C < TJ < 125 °C
V
OUT +1 V ≤ VIN ≤ 5.5 V,
ΔVOUT Static line regulation
ΔVOUT Static load regulation
VDROP Dropout voltage (1)
0.01
0.002
90
%/V
%/mA
mV
IOUT = 1 mA
IOUT = 1 mA to 150 mA
IOUT = 100 mA, VOUT > 1.5 V
-40 °C < TJ < 125 °C
130
10 Hz to 100 kHz, IOUT = 10 mA,
VOUT = 1.8 V, VIN = 2.8 V
eN
Output noise voltage
54
74
µVRMS
VIN = VOUTNOM + 1 V +/-VRIPPLE
VRIPPLE = 0.1 V, freq. = 1 kHz
IOUT = 10 mA
Supply voltage rejection
VOUT = 1.5V
SVR
dB
VIN = VOUTNOM + 0.5 V +/-VRIPPLE
VRIPPLE = 0.1 V, Freq.=10 kHz
67
20
I
OUT = 10 mA
I
OUT = 0 mA
IOUT = 0 mA, -40 °C < TJ < 125 °C
OUT = 0 to 150 mA
40
I
35
IQ
Quiescent current
Short circuit current
µA
IOUT = 0 to 150 mA
-40 °C < TJ< 125 °C
50
1
VIN input current in OFF MODE:
0.003
V
EN = GND
ISC
RL = 0
200
mA
DocID15968 Rev 4
7/16
16
Electrical characteristics
LD39015J
Table 5. Electrical characteristics (continued)
Test conditions Min.
VIN = 1.5 V to 5.5 V,
-40 °C < TJ < 125 °C
IN = 1.5 V to 5.5 V,
Symbol
Parameter
Typ.
Max.
Unit
Enable input logic low
0.4
V
VEN
V
Enable input logic high
0.9
V
-40 °C < TJ < 125°C
IEN
Enable pin input current
Turn on time (2)
VSHDN = VIN, -40 °C < TJ < 125 °C
0.1
30
1
µA
µs
TON
Thermal shutdown
Hysteresis
160
20
TSHDN
°C
µF
Capacitance (see typical
performance characteristics for
stability)
COUT Output capacitor
1
22
1. Dropout voltage is the input-to-output voltage difference at which the output voltage is 100 mV below its nominal value. This
specification does not apply for output voltages below 1.5 V.
2. Turn-on time is time measured between the enable input just exceeding V High Value and the output voltage just
EN
reaching 95% of its nominal value.
8/16
DocID15968 Rev 4
LD39015J
Typical performance characteristics
6
Typical performance characteristics
Figure 4. Output voltage vs. temperature
Figure 5. Output voltage vs. input voltage
1.24
1.23
1.22
1.21
1.2
2
1.8
1.6
1.4
1.2
1
1 mA
150 mA
1.19
1.18
1.17
1.16
1.15
1.14
0.8
0.6
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
-75 -50 -25
0
25 50 75 100 125 150 175
VIN [V]
T [°C]
Figure 6. Dropout voltage vs. output current
Figure 7. COUT stability region
3
2.5
2
CI = 1 µF, VIN = VEN = VOUTNOM +1 to 5.5 V
IOUT=1 to 150mA
1.5
1
STABLE ZONE
0.5
0
0
5
10
15
20
COUT [µF] (nominal value)
Figure 8. Supply voltage rejection vs. frequency
Figure 9. Output noise spectral density
Noise spectrum - VOUT(NOM) = 1.2V VIN=2.2V
1.4E-05
1.2E-05
IOUT = 0A
1.0E-05
IOUT = 1mA
IOUT = 10mA
8.0E-06
IOUT = 100mA
6.0E-06
4.0E-06
2.0E-06
0.0E+00
10
100
1000
10000
100000
f [Hz]
DocID15968 Rev 4
9/16
16
Typical performance characteristics
Figure 10. SVR vs. drop
LD39015J
Figure 11. Quiescent current vs. IOUT
90
IQ versus IOUT
IOUT = 10 mA, VOUT = 1.8 V, ΔVIN = 0.3 V, f = 1kHz
40
35
30
25
20
15
10
5
85
80
75
70
65
60
0
0
10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0
0.5
1
1.5
2
2.5
3
3.5
4
IOUT [mA]
VDROP(VIN - VOUT
)
Figure 12. Quiescent current vs. input voltage
Figure 13. Load transient
IQ(GND) versus VIN
ILOAD = 1mA
35
ILOAD = 0
30
25
20
15
10
5
0
0
1
2
3
4
5
6
7
VIN [V]
I
= 10mA to 150mA, t = t = 5µs
r f
OUT
Figure 14. Line transient
Figure 15. Enable transient
V
= 1.5 V, V = 0 to 1 V, I
= 1 mA, C = C
= 1 µF
OUT
I
= 10 mA; V
= 1.8 V; ΔV = 0.5 V; V = from 2.550
f
IN
EN
OUT
IN
OUT
OUT
IN
IN
to 3.055V; T = T = 5 µs
r
10/16
DocID15968 Rev 4
LD39015J
Package mechanical data
7
Package mechanical data
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK is an ST trademark.
Figure 16. Flip-chip 4 drawings
ꢀꢁꢁꢂꢀꢃꢄ*
DocID15968 Rev 4
11/16
16
Package mechanical data
LD39015J
Figure 17. Flip-chip 4 footprint
Table 6. Flip-chip 4 mechanical data
mm
Dim.
Min.
Typ.
Max.
A
A1
A2
b
0.585
0.21
0.65
0.25
0.40
0.315
1.07
0.5
0.715
0.29
0.265
1.02
0.365
1.12
D
D1
E
1.02
1.07
0.5
1.12
E1
SD
SE
0.25
0.25
12/16
DocID15968 Rev 4
LD39015J
Packaging mechanical data
8
Packaging mechanical data
Figure 18. Flip-chip 4 tape and reel drawing
DocID15968 Rev 4
13/16
16
Packaging mechanical data
LD39015J
Table 7. Flip-chip 4 tape and reel mechanical data
mm
Dim.
Min.
Typ.
Max.
A
C
178
12.8
20.2
59
13.2
D
N
60
61
8.4
T
Ao
Bo
Ko
Po
P
1.12
1.12
0.68
3.9
1.17
1.17
0.73
4.0
1.22
1.22
0.78
4.1
3.9
4.0
4.1
14/16
DocID15968 Rev 4
LD39015J
Revision history
9
Revision history
Table 8. Document revision history
Changes
Date
Revision
29-Jun-2009
1
2
3
First release.
05-Aug-2009
11-Sep-2012
Updated tape and reel mechanical data.
Added: new order code LD39015J25R Table 1 on page 1
.
Part number LD39015JXX changed to LD39015J.
Updated the Description in cover page, Section 7: Package mechanical data
Added Section 8: Packaging mechanical data
Minor text changes.
.
08-Jan-2014
4
.
DocID15968 Rev 4
15/16
16
LD39015J
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
ST PRODUCTS ARE NOT DESIGNED OR AUTHORIZED FOR USE IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE
SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B)
AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS
OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT
PURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN WRITING OF SUCH USAGE, UNLESS A PRODUCT IS
EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR “AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRY
DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS. PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE
DEEMED SUITABLE FOR USE IN AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2014 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
16/16
DocID15968 Rev 4
相关型号:
©2020 ICPDF网 联系我们和版权申明