LM158_08 [STMICROELECTRONICS]
Low power dual operational amplifiers; 低功耗双运算放大器型号: | LM158_08 |
厂家: | ST |
描述: | Low power dual operational amplifiers |
文件: | 总19页 (文件大小:323K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LM158-LM258-LM358
Low power dual operational amplifiers
Features
■ Internally frequency compensated
■ Large DC voltage gain: 100 dB
N
DIP8
(Plastic package)
■ Wide bandwidth (unity gain): 1.1 MHz
(temperature compensated)
■ Very low supply current per operator
essentially independent of supply voltage
■ Low input bias current: 20 nA
(temperature compensated)
D & S
SO-8 & miniSO-8
(Plastic micropackage)
■ Low input offset voltage: 2 mV
■ Low input offset current: 2 nA
■ Input common-mode voltage range includes
negative rails
■ Differential input voltage range equal to the
power supply voltage
+
■ Large output voltage swing 0 V to (V
- 1.5V)
CC
P
TSSOP8
(Thin shrink small outline package)
Description
These circuits consist of two independent, high-
gain, internally frequency-compensated op-amps
which are designed specifically to operate from a
single power supply over a wide range of
voltages. The low power supply drain is
independent of the magnitude of the power supply
voltage.
Pin connections
(Top view)
1
2
3
4
8
7
6
5
-
Application areas include transducer amplifiers,
DC gain blocks and all the conventional op-amp
circuits which now can be more easily
+
-
+
implemented in single power supply systems. For
example, these circuits can be directly supplied
with the standard +5 V which is used in logic
systems and will easily provide the required
interface electronics without requiring any
additional power supply.
1 - Output 1
2 - Inverting input
3 - Non-inverting input
4 - VCC
-
5 - Non-inverting input 2
6 - Inverting input 2
7 - Output 2
In linear mode, the input common-mode voltage
range includes ground and the output voltage can
also swing to ground, even though operated from
only a single power supply voltage.
8 - VCC
+
February 2008
Rev 7
1/19
www.st.com
19
Schematic diagram
LM158-LM258-LM358
1
Schematic diagram
Figure 1.
Schematic diagram (1/2 LM158)
VCC
6μA
4μA
100μA
Q5
Q6
CC
Q3
Q2
Inverting
input
Q7
Q1
Q4
R SC
Q11
Non-inverting
input
Output
Q13
Q10
Q12
Q8
Q9
50μA
GND
2/19
LM158-LM258-LM358
Absolute maximum ratings
2
Absolute maximum ratings
Table 1.
Symbol
Absolute maximum ratings
Parameter
LM158,A
LM258,A LM358,A Unit
VCC
Vi
Supply voltage
+/-16 or 32
V
V
V
Input voltage
32
32
Vid
Differential input voltage
Output short-circuit duation (1)
Input current (2)
Infinite
50
Iin
Toper
Tstg
Tj
mA
°C
°C
°C
Operating free-air temperature range
Storage temperature range
Maximum junction temperature
Thermal resistance junction to ambient(3)
-55 to +125 -40 to +105 0 to +70
-65 to +150
150
SO-8
125
190
120
85
Rthja
°C/W
°C/W
MiniSO-8
TSSOP8
DIP8
Thermal resistance junction to case (3)
SO-8
40
39
37
41
Rthjc
ESD
MiniSO-8
TSSOP8
DIP8
HBM: human body model(4)
MM: machine model(5)
300
200
1.5
V
V
CDM: charged device model(6)
kV
1. Short-circuits from the output to VCC can cause excessive heating if VCC > 15 V. The maximum output
current is approximately 40 mA independent of the magnitude of VCC. Destructive dissipation can result
from simultaneous short-circuits on all amplifiers.
2. This input current only exists when the voltage at any of the input leads is driven negative. It is due to the
collector-base junction of the input PNP transistor becoming forward biased and thereby acting as input
diode clamps. In addition to this diode action, there is also NPN parasitic action on the IC chip. This
transistor action can cause the output voltages of the Op-amps to go to the VCC voltage level (or to ground
for a large overdrive) for the time during which an input is driven negative.
This is not destructive and normal output is restored for input voltages above -0.3 V.
3. Short-circuits can cause excessive heating and destructive dissipation. Rth are typical values.
4. Human body model: A 100pF capacitor is charged to the specified voltage, then discharged through a
1.5kΩ resistor between two pins of the device. This is done for all couples of connected pin combinations
while the other pins are floating.
5. Machine model: A 200pF capacitor is charged to the specified voltage, then discharged directly between
two pins of the device with no external series resistor (internal resistor < 5Ω). This is done for all couples of
connected pin combinations while the other pins are floating.
6. Charged device model: all pins and the package are charged together to the specified voltage and then
discharged directly to the ground through only one pin. This is done for all pins.
3/19
Operating conditions
LM158-LM258-LM358
3
Operating conditions
Table 2.
Symbol
Operating conditions
Parameter
Value
Unit
VCC
Vicm
Supply voltage
3 to 30
V
V
Common mode input voltage range
VCC- -0.3 to VCC+ -1.5
Operating free air temperature range
-55 to +125
-40 to +105
0 to +70
LM158
LM258
LM358
Toper
°C
4/19
LM158-LM258-LM358
Electrical characteristics
4
Electrical characteristics
+
-
Table 3.
Symbol
Electrical characteristics for V
(unless otherwise specified)
= +5V, V
= Ground, V = 1.4V, T
= +25°C
CC
CC
o
amb
Parameter
Min.
Typ.
Max.
Unit
Input offset voltage (1)
LM158A
2
3
5
7
LM258A, LM358A
LM158, LM258
LM358
1
2
Vio
mV
Tmin ≤ Tamb ≤ Tmax
LM158A, LM258A, LM358A
LM158, LM258
LM358
4
7
9
Input offset voltage drift
DVio
µV/°C
nA
LM158A, LM258A, LM358A
LM158, LM258, LM358
7
7
15
30
Input offset current
LM158A, LM258A, LM358A
LM158, LM258, LM358
2
2
10
30
Iio
Tmin ≤ Tamb ≤ Tmax
LM158A, LM258A, LM358A
LM158, LM258, LM358
30
40
Input offset current drift
DIio
pA/°C
nA
LM158A, LM258A, LM358A
LM158, LM258, LM358
10
10
200
300
Input bias current (2)
LM158A, LM258A, LM358A
LM158, LM258, LM358
20
20
50
150
Iib
Tmin ≤ Tamb ≤ Tmax
LM158A, LM258A, LM358A
LM158, LM258, LM358
100
200
Large signal voltage gain
Avd
SVR
ICC
VCC+= +15 V, RL = 2 kΩ, Vo = 1.4 V to 11.4 V
Tmin ≤ Tamb ≤ Tmax
50
25
100
100
0.7
V/mV
dB
Supply voltage rejection ratio
VCC+ = 5 V to 30 V, Rs ≤ 10 kΩ
Tmin ≤ Tamb ≤ Tmax
65
65
Supply current, all amp, no load
Tmin ≤ Tamb ≤ Tmax VCC+ = +5 V
1.2
2
mA
V
Tmin ≤ Tamb ≤ Tmax VCC+ = +30 V
Input common mode voltage range
VCC+= +30 V (3)
Vicm
0
0
VCC+ -1.5
VCC+ -2
Tmin ≤ Tamb ≤ Tmax
5/19
Electrical characteristics
LM158-LM258-LM358
+
-
Table 3.
Symbol
Electrical characteristics for V
(unless otherwise specified)
= +5V, V
= Ground, V = 1.4V, T
= +25°C
CC
CC
o
amb
Parameter
Min.
Typ.
Max.
Unit
Common mode rejection ratio
Rs ≤ 10 kΩ
Tmin ≤ Tamb ≤ Tmax
CMR
Isource
Isink
70
60
85
dB
Output current source
VCC+ = +15 V, Vo = +2 V, Vid = +1 V
20
40
60
mA
Output sink current
VCC+ = +15V, Vo = +2V, Vid = -1V
10
12
20
50
mA
µA
VCC+ = +15V, Vo = +0.2V, Vid = -1V
High level output voltage
RL = 2 kΩ, VCC+ = 30 V
Tmin ≤ Tamb ≤ Tmax
26
26
27
27
27
28
VOH
V
RL = 10 kΩ, VCC+ = 30 V
Tmin ≤ Tamb ≤ Tmax
Low level output voltage
RL = 10 kΩ
Tmin ≤ Tamb ≤ Tmax
VOL
SR
5
20
20
mV
V/µs
MHz
%
Slew rate
VCC+ = 15V, Vi = 0.5 to 3V, RL = 2kΩ,
CL = 100pF, unity Gain
0.3
0.7
0.6
1.1
0.02
Gain bandwidth product
VCC+ = 30 V, f = 100 kHz,Vin = 10 mV,
RL = 2 kΩ, CL = 100 pF
GBP
THD
Total harmonic distortion
f = 1 kHz, Av = 20 dB, RL = 2 kΩ, Vo = 2 Vpp
CL = 100 pF, VO = 2 Vpp
,
Equivalent input noise voltage
f = 1 kHz, Rs = 100 Ω, VCC+ = 30 V
nV
en
55
-----------
Hz
Channel separation(4)
Vo1/Vo2
120
dB
1kHz ≤ f ≤ 20 kHz
1. Vo = 1.4 V, Rs = 0 Ω, 5 V < VCC+ < 30 V, 0 < Vic < VCC+ - 1.5 V
2. The direction of the input current is out of the IC. This current is essentially constant, independent of the state of the output
so there is no change in the load on the input lines.
3. The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3 V.
The upper end of the common-mode voltage range is VCC+ - 1.5 V, but either or both inputs can go to +32 V without
damage.
4. Due to the proximity of external components, ensure that stray capacitance between these external parts does not cause
coupling. Typically, this can be detected because this type of capacitance increases at higher frequencies.
6/19
LM158-LM258-LM358
Electrical characteristics
Figure 2.
Open loop frequency response
Figure 3.
Large signal frequency response
20
140
100k
W
10M
W
0.1
F
120
100
m
1k
W
+15V
-
V
-
CC
VO
V
V
15
10
V
I
I
O
V
/2
CC
2k
+
W
+
+7V
80
60
40
V
CC
-55°C
= 30V &
T
amb
+125°C
5
0
20
0
V
= +10 to + 15V &
CC
T
amb
+125°C
-55°C
1.0 10
100
1k
10k 100k 1M 10M
1k
10k
100k
1M
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 4.
Voltage follower pulse response
Figure 5.
Voltage follower pulse response
4
3
2
1
0
3
2
1
500
450
400
350
300
250
RL 2 k
VCC = +15V
W
+
e
O
e
l
-
50pF
Input
Output
T
V
= +25°C
= 30 V
amb
CC
0
10
20
30
40
0
1
2
3
4
5
6
7
8
TIME ( s)
TIME ( s)
m
m
Figure 6.
Input current
Figure 7.
Output characteristics
10
90
80
70
60
VCC = +5V
VCC = +15V
VCC = +30V
V = 0 V
I
V
V
= +30 V
= +15 V
CC
1
50
40
v
cc
CC
v
/2
cc
-
30
20
10
0
0.1
I
O
V
= +5 V
V
+
CC
O
T
= +25°C
10
amb
0.01
0,001
0,01
0,1
1
100
-55 -35 -15
5
25 45 65 85 105 125
TEMPERATURE (°C)
OUTPUT SINK CURRENT (mA)
7/19
Electrical characteristics
LM158-LM258-LM358
Figure 8.
Output characteristics
Figure 9.
Current limiting
90
80
70
60
8
7
6
V
CC
-
I
O
+
-
V
V
/2
O
CC
+
50
40
5
I
O
4
30
20
10
0
Independent of V
CC
3
2
1
T
= +25°C
amb
-55 -35 -15
5
25 45 65 85 105 125
0,01
0,1
1
10
100
0,001
OUTPUT SOURCE CURRENT (mA)
TEMPERATURE (°C)
Figure 10. Input voltage range
Figure 11. Positive supply voltage
15
160
W
R L = 20k
120
10
Négative
W
R L = 2k
80
40
Positive
5
0
5
10
15
0
10
20
30
40
POWER SUPPLY VOLTAGE (±V)
POSITIVE SUPPLY VOLTAGE (V)
Figure 12. Input voltage range
Figure 13. Supply current
4
160
V
CC
W
R L = 20k
I
D
mA
-
120
80
3
2
1
W
R L = 2k
+
T
= 0°C to +125°C
40
amb
T
= -55°C
amb
0
10
20
30
0
10
20
30
POSITIVE SUPPLY VOLTAGE (V)
POSITIVE SUPPLY VOLTAGE (V)
8/19
LM158-LM258-LM358
Electrical characteristics
Figure 14. Input current
Figure 15. Gain bandwidth product
100
1.5
1.35
1.2
75
50
25
1.05
0.9
VCC
=
15V
0.75
0.6
0.45
0.3
Tamb= +25°C
0.15
0
-55-35-15 5 25 45 65 85 105 125
0
10
20
30
TEMPERATURE (°C)
POSITIVE SUPPLY VOLTAGE (V)
Figure 16. Power supply rejection ratio
Figure 17. Common mode rejection ratio
115
110
105
100
95
115
110
SVR
105
100
95
90
85
80
75
70
65
90
85
80
75
70
65
-55-35-15 5 25 45 65 85 105 125
60
-55-35-15 5 25 45 65 85 105 125
60
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 18. Phase margin vs. capacitive load
Phase Margin at Vcc=15V and Vicm=7.5V
Vs. Iout and Capacitive load value
9/19
Typical applications
LM158-LM258-LM358
5
Typical applications
Single supply voltage V = +5V
.
CC
DC
Figure 19. AC coupled inverting amplifier
Figure 20. Non-inverting DC amplifier
Rf
100k
R2
R1
W
Rf
A
V= 1 +
A = -
V
R1
10k
W
R1
(as shown A = -10)
A
(As shown V = 101)
V
CI
W
10k
eO
+5V
Co
1/2
LM158
1/2
LM158
2VPP
0
eo
R
B
W
R
L
W
6.2k
10k
eI
R2
100k
R3
W
100k
~
V
W
R2
CC
1M
W
R1
W
10k
C1
m
10
F
0
eI
(mV)
Figure 21. AC coupled non-inverting amplifier Figure 22. DC summing amplifier
e 1
W
R1
100k
R2
1M
100k
W
W
R2
R1
A
= 1 +
V
(as shown A = 11)
V
C1
0.1 F
m
eO
1/2
LM158
Co
100k
W
1/2
LM158
2VPP
0
eo
CI
e 2
e 3
W
W
100k
R
B
W
R
L
10k
6.2k
100k
W
R3
1M
eI
~
W
100k
W
R4
100k
W
e 4
100k
W
V
CC
C2
R5
W
100k
e
= e + e - e - e
1 2 3 4
m
o
10 F
where (e1 + e ) ≥ (e + e )
2
3
4
to keep e ≥ 0V
o
Figure 23. High input Z, DC differential
amplifier
Figure 24. High input Z adjustable gain DC
instrumentation amplifier
R1
100k
W
R4
100k
R3
100k
R4
100k
W
R2
100k
W
1/2
LM158
W
W
e1
R1
100k
eO
1/2
LM158
W
Gain adjust
R3
100k
R2
W
2k
R5
100k
W
W
1/2
LM158
1/2
LM158
R6
100k
R7
100k
W
V
o
+V1
+V2
W
1/2
LM158
e2
if R1 = R5 and
if R1 = R5 and R3 = R4 = R6 = R7
2R1
R3 = R4 = R6 = R7
e
= [1 +
] ( (e + e )
2 1
2R1
] ( (e + e )
2 1
-----------
e
= [ 1 +
o
-----------
R2
o
R2
As shown e = 101 (e + e )
o
2
1
As shown e = 101 (e + e )
o
2
1
10/19
LM158-LM258-LM358
Typical applications
Figure 25. Using symmetrical amplifiers to
reduce input current
Figure 26. Low drift peak detector
I
1/2
LM158
B
eo
I I
I
B
1/2
LM158
e I
eo
I
I
I
B
B
1/2
LM158
2N 929
Zo
C
2I
e I
B
1mF
m
0.001 F
ZI
2N 929
I
0.001
m
F
B
B
I
2I
B
1/2
B
W
3M
LM158
R
1/2
LM158
3R
3M
1M
W
Input current compensation
W
I
B
Input current
compensation
W
1.5M
I
B
Figure 27. Active band-pass filter
R1
100k
W
C1
330pF
1/2
R2
100k
R5
470k
LM158
W
W
+V1
R4
10M
W
1/2
LM158
C2
R6
470k
330 F
p
R3
100k
W
W
Vo
1/2
LM158
R7
100k
W
VCC
C3
R8
100k
m
10
F
W
11/19
Package information
LM158-LM258-LM358
6
Package information
In order to meet environmental requirements, STMicroelectronics offers these devices in
®
ECOPACK packages. These packages have a lead-free second level interconnect. The
category of second level interconnect is marked on the package and on the inner box label,
in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering
conditions are also marked on the inner box label. ECOPACK is an STMicroelectronics
trademark. ECOPACK specifications are available at: www.st.com.
12/19
LM158-LM258-LM358
Package information
6.1
DIP8 package information
Figure 28. DIP8 package mechanical drawing
Table 4.
Ref.
DIP8 package mechanical data
Millimeters
Dimensions
Inches
Min.
Typ.
Max.
Min.
Typ.
Max.
A
A1
A2
b
5.33
0.210
0.38
2.92
0.36
1.14
0.20
9.02
7.62
6.10
0.015
0.115
0.014
0.045
0.008
0.355
0.300
0.240
3.30
0.46
1.52
0.25
9.27
7.87
6.35
2.54
7.62
4.95
0.56
1.78
0.36
10.16
8.26
7.11
0.130
0.018
0.060
0.010
0.365
0.310
0.250
0.100
0.300
0.195
0.022
0.070
0.014
0.400
0.325
0.280
b2
c
D
E
E1
e
eA
eB
L
10.92
3.81
0.430
0.150
2.92
3.30
0.115
0.130
13/19
Package information
LM158-LM258-LM358
6.2
SO-8 package information
Figure 29. SO-8 package mechanical drawing
Table 5.
Ref.
SO-8 package mechanical data
Millimeters
Dimensions
Inches
Min.
Typ.
Max.
Min.
Typ.
Max.
A
A1
A2
b
1.75
0.25
0.069
0.010
0.10
1.25
0.28
0.17
4.80
5.80
3.80
0.004
0.049
0.011
0.007
0.189
0.228
0.150
0.48
0.23
5.00
6.20
4.00
0.019
0.010
0.197
0.244
0.157
c
D
4.90
6.00
3.90
1.27
0.193
0.236
0.154
0.050
H
E1
e
h
0.25
0.40
1°
0.50
1.27
8°
0.010
0.016
1°
0.020
0.050
8°
L
k
ccc
0.10
0.004
14/19
LM158-LM258-LM358
Package information
6.3
MiniSO-8 package information
Figure 30. MiniSO-8 package mechanical drawing
Table 6.
Ref.
MiniSO-8 package mechanical data
Dimensions
Millimeters
Typ.
Inches
Min.
Max.
Min.
Typ.
Max.
A
A1
A2
b
1.1
0.043
0.006
0.037
0.016
0.009
0.126
0.203
0.122
0
0.15
0.95
0.40
0.23
3.20
5.15
3.10
0
0.75
0.22
0.08
2.80
4.65
2.80
0.85
0.030
0.009
0.003
0.11
0.033
c
D
3.00
4.90
3.00
0.65
0.60
0.95
0.25
0.118
0.193
0.118
0.026
0.024
0.037
0.010
E
0.183
0.11
E1
e
L
0.40
0°
0.80
0.016
0°
0.031
L1
L2
k
8°
8°
ccc
0.10
0.004
15/19
Package information
LM158-LM258-LM358
6.4
TSSOP8 package information
Figure 31. TSSOP8 package mechanical drawing
Table 7.
Ref.
TSSOP8 package mechanical data
Dimensions
Millimeters
Typ.
Inches
Min.
Max.
Min.
Typ.
Max.
A
A1
A2
b
1.2
0.047
0.006
0.041
0.012
0.008
0.122
0.260
0.177
0.05
0.80
0.19
0.09
2.90
6.20
4.30
0.15
1.05
0.30
0.20
3.10
6.60
4.50
0.002
0.031
0.007
0.004
0.114
0.244
0.169
1.00
0.039
c
D
3.00
6.40
4.40
0.65
0.118
0.252
0.173
0.0256
E
E1
e
k
0°
8°
0°
8°
L
0.45
0.60
1
0.75
0.018
0.024
0.039
0.004
0.030
L1
aaa
0.1
16/19
LM158-LM258-LM358
Ordering information
7
Ordering information
Table 8.
Order codes
Temperature range
Order code
Package
Packaging
Marking
LM158N
DIP8
Tube
LM158N
LM158D
LM158DT
SO-8
158
-55°C, +125°C
Tube or tape & reel
Tube
LM158YD(1)
SO-8
Automotive grade
158Y
LM258A
258A
LM158YDT(1)
LM258AN
DIP8
SO-8
LM258AD
LM258ADT
Tube or tape & reel
LM258AYD(1)
SO-8
Automotive grade
258AY
LM258AYDT(1)
258
258A
LM258PT
TSSOP8
LM258APT
Tape & reel
LM258YPT(2)
LM258AYPT(2)
TSSOP8
-40°C, +105°C
258Y
Automotive grade
258AY
K408
LM258AST
LM258N
MiniSO-8
DIP8
Tape & reel
Tube
LM258N
LM258D
LM258DT
SO-8
258
Tube or tape & reel
Tube
LM258YD(1)
SO-8
Automotive grade
258Y
LM258YDT(1)
LM358N
LM358N
DIP8
SO-8
LM358AN
LM358AN
LM358D
LM358DT
358
LM358YD(1)
SO-8
Automotive grade
Tube or tape & reel
358Y
358A
LM358YDT(1)
LM358AD
LM358ADT
SO-8
0°C, +70°C
358
358A
358Y
358AY
K405
K404
LM358PT
TSSOP8
LM358APT
Tape & reel
Tape & reel
LM358YPT(2)
LM358AYPT(2)
TSSOP8
Automotive grade
LM358ST
MiniSO-8
LM358AST
1. Qualified and characterized according to AEC Q100 and Q003 or equivalent, advanced screening according to AEC Q001
& Q 002 or equivalent.
2. Qualification and characterization according to AEC Q100 and Q003 or equivalent, advanced screening according to AEC
Q001 & Q 002 or equivalent are on-going.
17/19
Revision history
LM158-LM258-LM358
8
Revision history
Table 9.
Date
Document revision history
Revision
Changes
1-Jul- 2003
2-Jan-2005
1-Jul-2005
5-Oct-2006
30-Nov-2006
1
2
3
4
5
First release.
Rthja and Tj parameters added in AMR Table 1 on page 3.
ESD protection inserted in Table 1 on page 3.
Added Figure 18: Phase margin vs. capacitive load.
Added missing ordering information.
Removed LM158A, LM258A and LM358A from document title.
Corrected error in MiniSO-8 package data. L1 is 0.004 inch.
Added automotive grade order codes in Section 7 on page 17.
25-Apr-2007
6
Corrected VCC max (30V instead of 32V) in operating conditions.
Changed presentation of electrical characteristics table.
Deleted Vopp parameter in electrical characteristics table.
Corrected miniSO-8 package information.
12-Feb-2008
7
Corrected temperature range for automotive grade order codes.
Updated automotive grade footnotes in order codes table.
18/19
LM158-LM258-LM358
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2008 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
19/19
相关型号:
©2020 ICPDF网 联系我们和版权申明