TS882IQ2T [STMICROELECTRONICS]
Rail-to-rail 1.1 V dual and quad nanopower comparators;型号: | TS882IQ2T |
厂家: | ST |
描述: | Rail-to-rail 1.1 V dual and quad nanopower comparators 放大器 光电二极管 |
文件: | 总26页 (文件大小:1079K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TS882
TS884
Rail-to-rail 1.1 V dual and quad nanopower comparators
Datasheet
-
production data
•
Quad version available in SO14, TSSOP14
and QFN16 3 x 3 mm package
Related product
•
See the TS881 datasheet for single operator
with smaller package.
DFN8 (2 x 2 mm)
MiniSO8
SO14
Applications
•
•
•
Portable systems
Signal conditioning
Medical
TSSOP14
Description
The TS882 is a dual and the TS884 device a
quad comparator featuring ultra-low supply
current (220 nA typical per operator with output
high, VCC = 1.2 V, no load) with rail-to-rail input
and output capability. The performance of these
comparators allows them to be used in a wide
range of portable applications. The TS882 and
TS884 devices minimize battery supply leakage
and therefore enhance battery lifetime.
QFN16 (3 x 3 mm)
Features
•
•
•
•
•
•
•
•
Ultra-low current consumption: 220 nA typ./op.
Propagation delay: 2 µs typ.
Rail-to-rail inputs
Operating from 1.1 to 5.5 V supply voltage, these
comparators can be used over a wide
temperature range (-40 to +125 °C) keeping the
current consumption at an ultra-low level.
Push-pull outputs
Supply operation from 1.1 V to 5.5 V
Wide temperature range: -40 to +125 °C
ESD tolerance: 8 kV HBM / 300 V MM
Dual version available in MiniSO8 and DFN8
(2 x 2 mm) package
Table 1. Device summary
Order codes
Temperature range
Packages
Packaging
Marking
TS882IST
TS882IQ2T
TS884IDT
TS884IPT
TS884IQ4T
MiniSO8
DFN8 2 x 2 mm
SO14
K514
K56
-40 to +125 °C
Tape and reel
S884I
S884I
K514
-40 to +125 °C
TSSOP14
Tape and reel
QFN16 3 x 3 mm
July 2014
DocID024119 Rev 3
1/26
This is information on a product in full production.
www.st.com
Contents
TS882, TS884
Contents
1
2
3
4
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Absolute maximum ratings and operating conditions . . . . . . . . . . . . . 4
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4.1
4.2
4.3
4.4
4.5
DFN8 2 x 2 mm package mechanical data . . . . . . . . . . . . . . . . . . . . . . . 17
MiniSO8 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
SO14 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
QFN16 3 x 3 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
TSSOP14 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
5
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
2/26
DocID024119 Rev 3
TS882, TS884
Pin description
1
Pin description
Figure 1. Pin connections TS882 (top view)
TS882IDT/IST/IQ2T
MiniSO8/DFN8
Figure 2. Pin connections TS884 (top view)
SO14 / TSSOP14
287ꢄ 287ꢀ
,1ꢄꢂ
,1ꢀꢂ
ꢄꢆ ꢄꢇ ꢄꢀ ꢄꢃ
ꢄ
ꢅ
ꢃ
ꢀ
ꢄꢅ
ꢄꢄ
ꢄꢈ
ꢉ
,1ꢄꢁ
9&&ꢁ
1&
,1ꢀꢁ
9&&ꢂ
1&
,1ꢅꢁ
,1ꢃꢁ
ꢇ
ꢆ
ꢊ
ꢋ
,1ꢅꢂ
,1ꢃꢂ
287ꢅ 287ꢃ
QFN16
DocID024119 Rev 3
3/26
26
Absolute maximum ratings and operating conditions
TS882, TS884
2
Absolute maximum ratings and operating conditions
Table 2. Absolute maximum ratings
Parameter
Symbol
Value
Unit
VCC
VID
VIN
Supply voltage(1)
6
V
V
V
Differential input voltage(2)
±6
Input voltage range
(VCC-) - 0.3 to (VCC+) + 0.3
Thermal resistance junction to ambient (TS882)(3)
MiniSO8
190
57
DFN8 2 x 2 mm
Thermal resistance junction to ambient (TS884)(3)
RTHJA
°C/W
SO14
105
100
45
TSSOP14
QFN16 3 x 3 mm
TSTG Storage temperature
TJ Junction temperature
-65 to +150
150
°C
°C
°C
kV
TLEAD Lead temperature (soldering 10 seconds)
Human body model (HBM)(4)
260
8
ESD
Machine model (MM)(5)
Charged device model (CDM)(6)
Latch-up immunity
300
V
1300
200
mA
1. All voltage values, except differential voltages, are referenced to V -. V is defined as the difference
CC
CC
between V + and V -.
CC
CC
2. The magnitude of input and output voltages must never exceed the supply rail ±0.3 V.
3. Short-circuits can cause excessive heating. These values are typical.
4. According to JEDEC standard JESD22-A114F.
5. According to JEDEC standard JESD22-A115A.
6. According to ANSI/ESD STM5.3.1.
Table 3. Operating conditions
Symbol
Parameter
Value
Unit
Toper Operating temperature range
-40 to +125
°C
Supply voltage
VCC
V
V
-40 °C < Tamb < +125 °C
1.1 to 5.5
Common mode input voltage range
VICM -40 °C < Tamb < +85 °C
-40 °C < Tamb < +125 °C
(VCC-) - 0.2 to (VCC+) + 0.2
(VCC-) to (VCC+) + 0.2
4/26
DocID024119 Rev 3
TS882, TS884
Electrical characteristics
3
Electrical characteristics
Table 4. VCC = +1.2 V, Tamb = +25 °C, VICM = VCC/2 (unless otherwise specified)(1)
Symbol
VIO
Parameter
Test conditions
Min.
Typ.
Max.
Unit
Tamb = +25 °C
1
Input offset voltage(2)
mV
µV/°C
mV
-40 °C < Tamb < +125 °C
-40 °C < Tamb < +125 °C
-6
6
∆VIO Input offset voltage drift
3
Tamb = +25 °C
2.4
VHYST Input hysteresis voltage(3)
-40 °C < Tamb < +125 °C
1.5
4.2
Tamb = +25 °C
10
100
IIO
Input offset current(4)
Input bias current(4)
pA
pA
-40 °C < Tamb < +125 °C
Tamb = +25 °C
1
10
100
IIB
-40 °C < Tamb < +125 °C
No load, output low, VID = -0.1 V
-40 °C < Tamb < +125 °C
300
450
350
ICC
Supply current per operator
nA
No load, output high, VID = +0.1 V
-40 °C < Tamb < +125 °C
220
Source
Sink
1.0
1.7
ISC
Short-circuit current
Output voltage high
mA
V
Isource = 0.2 mA
-40 °C < Tamb < +85 °C
-40 °C < Tamb < +125 °C
1.13
1.10
1.00
1.15
VOH
Isink = 0.2 mA
-40 °C < Tamb < +85 °C
-40 °C < Tamb < +125 °C
35
50
60
70
VOL
Output voltage low
mV
dB
0 < VICM < VCC
-40 °C < Tamb < +125 °C
68
CMRR Common mode rejection ratio
50
f = 1 kHz, CL = 30 pF, RL = 1 MΩ
5.5
2.1
11
13
Overdrive = 10 mV
-40 °C < Tamb < +125 °C
Propagation delay
TPLH
µs
(low to high)
3.1
3.4
Overdrive = 100 mV
-40 °C < Tamb < +125 °C
f = 1 kHz, CL = 30 pF, RL = 1 MΩ
Overdrive = 10 mV
5.1
8
Propagation delay
TPHL
-40 °C < Tamb < +125 °C
10
µs
ns
(high to low)
Overdrive = 100 mV
-40 °C < Tamb < +125 °C
1.9
2.6
3.1
TR
Rise time (10% to 90%)
CL = 30 pF, RL = 1 MΩ
100
DocID024119 Rev 3
5/26
26
Electrical characteristics
TS882, TS884
Table 4. VCC = +1.2 V, Tamb = +25 °C, VICM = VCC/2 (unless otherwise specified)(1) (continued)
Symbol
Parameter
Test conditions
Min.
Typ.
Max.
Unit
TF
Fall time (90% to 10%)
Power-up time
CL = 30 pF, RL = 1 MΩ
110
1.1
ns
TON
1.7
ms
1. All values over the temperature range are guaranteed through correlation and simulation. No production test is performed
at the temperature range limits.
2. The offset is defined as the average value of positive and negative trip points (input voltage differences requested to
change the output state in each direction).
3. The hysteresis is a built-in feature of the TS882 device. It is defined as the voltage difference between the trip points.
4. Maximum values include unavoidable inaccuracies of the industrial tests.
6/26
DocID024119 Rev 3
TS882, TS884
Electrical characteristics
Table 5. VCC = +2.7 V, Tamb = +25 °C, VICM = VCC/2 (unless otherwise specified)(1)
Symbol
Parameter
Test conditions
Min.
Typ.
Max.
Unit
Tamb = +25 °C
1
VIO
Input offset voltage(2)
mV
µV/°C
mV
-40 °C < Tamb < +125 °C
-40 °C < Tamb < +125 °C
-6
6
∆VIO Input offset voltage drift
3
Tamb = +25 °C
2.7
VHYST Input hysteresis voltage(3)
-40 °C < Tamb < +125 °C
1.6
4.2
Tamb = +25 °C
10
100
IIO
Input offset current(4)
Input bias current(4)
pA
pA
-40 °C < Tamb < +125 °C
Tamb = +25 °C
1
10
100
IIB
-40 °C < Tamb < +125 °C
No load, output low, VID = -0.1 V
-40 °C < Tamb < +125 °C
310
450
350
ICC
Supply current per operator
nA
No load, output high, VID = +0.1 V
-40 °C < Tamb < +125 °C
220
Source
Sink
10
13
ISC
Short-circuit current
Output voltage high
mA
V
Isource = 2 mA
-40 °C < Tamb < +85 °C
-40 °C < Tamb < +125 °C
2.48
2.40
2.10
2.51
130
74
VOH
Isink = 2 mA
-40 °C < Tamb < +85 °C
-40 °C < Tamb < +125 °C
210
230
310
VOL
Output voltage low
mV
dB
0 < VICM < VCC
-40 °C < Tamb < +125 °C
CMRR Common mode rejection ratio
55
f = 1 kHz, CL = 30 pF, RL = 1 MΩ
Overdrive = 10 mV
-40 °C < Tamb < +125 °C
6.4
2.3
12
14
Propagation delay
TPLH
µs
µs
(low to high)
Overdrive = 100 mV
-40 °C < Tamb < +125 °C
3.0
3.7
f = 1 kHz, CL = 30 pF, RL = 1 MΩ
Overdrive = 10 mV
-40 °C < Tamb < +125 °C
6.4
2.2
12
14
Propagation delay
TPHL
(high to low)
Overdrive = 100 mV
-40 °C < Tamb < +125 °C
3.0
3.7
TR
TF
Rise time (10% to 90%)
Fall time (90% to 10%)
Power-up time
CL = 30 pF, RL = 1 MΩ
CL = 30 pF, RL = 1 MΩ
120
130
1.1
ns
ns
TON
1.7
ms
1. All values over the temperature range are guaranteed through correlation and simulation. No production test is performed
at the temperature range limits.
2. The offset is defined as the average value of positive and negative trip points (input voltage differences requested to
change the output state in each direction).
3. The hysteresis is a built-in feature of the TS882. It is defined as the voltage difference between the trip points.
4. Maximum values include unavoidable inaccuracies of the industrial tests.
DocID024119 Rev 3
7/26
26
Electrical characteristics
TS882, TS884
Table 6. VCC = +5 V, Tamb = +25 °C, VICM = VCC/2 (unless otherwise specified)(1)
Symbol
Parameter
Test conditions
Min.
Typ.
Max.
Unit
Tamb = +25 °C
1
VIO
Input offset voltage(2)
mV
µV/°C
mV
-40 °C < Tamb < +125 °C
-40 °C < Tamb < +125 °C
-6
6
∆VIO Input offset voltage drift
3
Tamb = +25 °C
3.1
VHYST Input hysteresis voltage(3)
-40 °C < Tamb < +125 °C
1.6
4.2
Tamb = +25 °C
10
100
IIO
Input offset current(4)
Input bias current(4)
pA
pA
-40 °C < Tamb < +125 °C
Tamb = +25 °C
1
10
100
IIB
-40 °C < Tamb < +125 °C
No load, output low, VID = -0.1 V
-40 °C < Tamb < +125 °C
350
500
400
ICC
Supply current per operator
nA
No load, output high, VID = +0.1 V
-40 °C < Tamb < +125 °C
250
Source
Sink
32
32
ISC
Short-circuit current
Output voltage high
mA
V
Isource = 2 mA
-40 °C < Tamb < +85 °C
-40 °C < Tamb < +125 °C
4.86
4.75
4.60
4.88
VOH
Isink = 2 mA
-40 °C < Tamb < +85 °C
-40 °C < Tamb < +125 °C
90
130
170
280
VOL
Output voltage low
mV
0 < VICM < VCC
-40 °C < Tamb < +125 °C
78
80
CMRR Common mode rejection ratio
dB
dB
55
65
∆VCC = 1.2 V to 5 V
-40 °C < Tamb < +125 °C
SVR
Supply voltage rejection
f = 1 kHz, CL = 30 pF, RL = 1 MΩ
Overdrive = 10 mV
-40 °C < Tamb < +125 °C
8.3
2.5
13
22
Propagation delay
(low to high)
TPLH
µs
Overdrive = 100 mV
-40 °C < Tamb < +125 °C
3.4
4.1
f = 1 kHz, CL = 30 pF, RL = 1 MΩ
Overdrive = 10 mV
-40 °C < Tamb < +125 °C
9.0
16
19
Propagation delay
(high to low)
TPHL
µs
ns
Overdrive = 100 mV
-40 °C < Tamb < +125 °C
2.6
3.5
4.2
TR
Rise time (10% to 90%)
CL = 30 pF, RL = 1 MΩ
160
8/26
DocID024119 Rev 3
TS882, TS884
Electrical characteristics
Table 6. VCC = +5 V, Tamb = +25 °C, VICM = VCC/2 (unless otherwise specified)(1) (continued)
Symbol
Parameter
Test conditions
Min.
Typ.
Max.
Unit
TF
Fall time (90% to 10%)
Power-up time
CL = 30 pF, RL = 1 MΩ
150
1.1
ns
TON
1.7
ms
1. All values over the temperature range are guaranteed through correlation and simulation. No production test is performed
at the temperature range limits.
2. The offset is defined as the average value of positive and negative trip points (input voltage differences requested to
change the output state in each direction).
3. The hysteresis is a built-in feature of the TS882 device. It is defined as the voltage difference between the trip points.
4. Maximum values include unavoidable inaccuracies of the industrial tests.
DocID024119 Rev 3
9/26
26
Electrical characteristics
TS882, TS884
Figure 3. Current consumption per operator vs. Figure 4. Current consumption per operator
supply voltage - output low vs. supply voltage - output high
Figure 5. Current consumption per operator Figure 6. Current consumption per operator
vs. input common mode voltage at
VCC = 1.2 V
vs. input common mode voltage at
VCC = 5 V
Figure 7. Current consumption per operator Figure 8. Current consumption per operator
vs. temperature vs. toggle frequency
10/26
DocID024119 Rev 3
TS882, TS884
Electrical characteristics
Figure 9. Input offset voltage vs. input
common mode voltage at
VCC = 1.2 V
Figure 10. Input hysteresis voltage vs. input
common mode voltage at
VCC = 1.2 V
Figure 11. Input offset voltage vs. input
common mode voltage at VCC = 5 V
Figure 12. Input hysteresis voltage vs. input
common mode voltage at VCC = 5 V
Figure 13. Input offset voltage vs. temperature Figure 14. Input hysteresis voltage vs.
temperature
DocID024119 Rev 3
11/26
26
Electrical characteristics
TS882, TS884
Figure 15. Output voltage drop vs. sink current Figure 16. Output voltage drop vs. source
at VCC = 1.2 V current at VCC = 1.2 V
Figure 17. Output voltage drop vs. sink current Figure 18. Output voltage drop vs. source
at VCC = 2.7 V current at VCC = 2.7 V
Figure 19. Output voltage drop vs. sink current Figure 20. Output voltage drop vs. source
at VCC = 5 V current at VCC = 5 V
12/26
DocID024119 Rev 3
TS882, TS884
Electrical characteristics
Figure 21. Propagation delay TPLH vs. input
common mode voltage at VCC = 1.2 V
Figure 22. Propagation delay TPHL vs. input
common mode voltage at VCC = 1.2 V
Figure 23. Propagation delay TPLH vs. input
common mode voltage at VCC = 5 V
Figure 24. Propagation delay TPHL vs. input
common mode voltage at VCC = 5 V
Figure 25. Propagation delay TPLH vs. input
signal overdrive at VCC = 1.2 V
Figure 26. Propagation delay TPHL vs. input
signal overdrive at VCC = 1.2 V
DocID024119 Rev 3
13/26
26
Electrical characteristics
TS882, TS884
Figure 27. Propagation delay TPLH vs. input
signal overdrive at VCC = 5 V
Figure 28. Propagation delay TPHL vs. input
signal overdrive at VCC = 5 V
Figure 29. Propagation delay TPLH vs. supply Figure 30. Propagation delay TPHL vs. supply
voltage for signal overdrive 10 mV voltage for signal overdrive 10 mV
Figure 31. Propagation delay TPLH vs. supply Figure 32. Propagation delay TPHL vs. supply
voltage for signal overdrive 100 mV
voltage for signal overdrive 100 mV
14/26
DocID024119 Rev 3
TS882, TS884
Electrical characteristics
Figure 33. Propagation delay vs. temperature Figure 34. Propagation delay vs. temperature
for signal overdrive 10 mV for signal overdrive 100 mV
DocID024119 Rev 3
15/26
26
Package information
TS882, TS884
4
Package information
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK is an ST trademark.
16/26
DocID024119 Rev 3
TS882, TS884
Package information
4.1
DFN8 2 x 2 mm package mechanical data
Figure 35. DFN8 2 x 2 mm package outline
4&"5*/(ꢀꢀ
$
1-"/&
EEE
$
"ꢁ
"ꢂ
"
%
F
1*/ꢀꢂꢀ*%
ꢂ
ꢃ
ꢁ
ꢄ
&
&ꢃ
-
ꢅ
ꢆ
ꢇ
C
ꢈ
%ꢃ
Table 7. DFN8 2 x 2 mm package mechanical data (pitch 0.5 mm)
Dimensions
Symbol
Millimeters
Inches
Min.
Typ.
Max.
Min.
Typ.
Max.
A
A1
A3
b
0.51
0.55
0.60
0.05
0.020
0.022
0.024
0.002
0.15
0.25
2.00
1.60
2.00
0.90
0.50
0.006
0.010
0.079
0.063
0.079
0.035
0.020
0.18
1.85
1.45
1.85
0.75
0.30
2.15
1.70
2.15
1.00
0.007
0.073
0.057
0.073
0.030
0.012
0.085
0.067
0.085
0.039
D
D2
E
E2
e
L
0.50
0.08
0.020
0.003
ddd
DocID024119 Rev 3
17/26
26
Package information
TS882, TS884
Figure 36. DFN8 2 x 2 mm footprint recommendation
ꢀꢁꢂꢃꢄPP
ꢉꢁꢊꢃꢄPP
ꢃꢁꢅꢆꢄPP
ꢃꢁꢈꢆꢄPP
ꢃꢁꢆꢃꢄPP
ꢃꢁꢇꢃꢄPP
18/26
DocID024119 Rev 3
TS882, TS884
Package information
4.2
MiniSO8 package information
Figure 37. MiniSO8 package outline
Table 8. MiniSO8 package mechanical data
Dimensions
Symbol
Millimeters
Inches
Min.
Typ.
Max.
Min.
Typ.
Max.
A
A1
A2
b
1.10
0.15
0.95
0.40
0.23
3.20
5.15
3.10
0.043
0.006
0.037
0.016
0.009
0.126
0.203
0.122
0
0
0.75
0.22
0.08
2.80
4.65
2.80
0.85
0.030
0.009
0.003
0.11
0.033
c
D
3.00
4.90
3.00
0.65
0.60
0.95
0.25
0.118
0.193
0.118
0.026
0.024
0.037
0.010
E
0.183
0.11
E1
e
L
0.40
0°
0.80
0.016
0°
0.031
L1
L2
k
8°
8°
ccc
0.10
0.004
DocID024119 Rev 3
19/26
26
Package information
TS882, TS884
4.3
SO14 package information
Figure 38. SO14 package outline
Table 9. SO14 package mechanical data
Dimensions(1)
Millimeters
Typ.
Inches
Typ.
Symbol
Note
Min.
Max.
Min.
Max.
A
A1
A2
B
1.35
0.10
1.10
0.33
0.19
8.55
3.80
1.75
0.25
1.65
0.51
0.25
8.75
4.0
0.05
0.004
0.04
0.068
0.009
0.06
0.01
0.02
C
0.007
0.33
0.009
0.34
(2)
D
E
0.15
0.15
e
1.27
0.05
H
5.80
0.40
0°
6.20
1.27
8°
0.22
0.015
0°
0.24
0.05
8°
L
k
ddd
0.10
0.004
1. Drawing dimensions include “Single” and “Matrix” versions.
2. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold flash, protrusions or gate burrs
shall not exceed 0.15 mm per side.
20/26
DocID024119 Rev 3
TS882, TS884
Package information
4.4
QFN16 3 x 3 package information
Figure 39. QFN16 3 x 3 mm (pitch 0.5 mm) package outline
6($7,1*ꢀ
3/$1(
&
GGGꢀꢀꢀꢀꢀꢀꢀ&
$
$ꢂ
$ꢁ
'
3,1ꢀꢃꢂꢀ,'
&ꢀ ꢀꢄꢅꢁꢄ
'ꢂ
H
ꢂꢁ
ꢂꢆ
ꢂ
ꢂꢊ
H
(ꢂ
(
(ꢊ
E
ꢋ
ꢇ
/
ꢉ
ꢈ
E
/
'ꢊ
%27720ꢀ9,(:
DocID024119 Rev 3
21/26
26
Package information
TS882, TS884
Table 10. QFN16 3 x 3 mm (pitch 0.5 mm) package mechanical data
Dimensions
Symbol
Millimeters
Typ.
Inches
Typ.
Min.
Max.
Min.
Max.
A
A1
A3
b
0.80
0.90
0.02
0.20
0.25
3.00
1.50
1.00
0.05
0.031
0.035
0.001
0.008
0.010
0.118
0.059
0.039
0.002
0.18
2.85
0.30
3.15
0.007
0.112
0.012
0.124
D
D1
D2
E
See exposed pad variation
See exposed pad variation
2.85
3.00
1.50
3.15
0.112
0.118
0.059
0.124
E1
E2
e
See exposed pad variation
See exposed pad variation
0.45
0.30
0.50
0.40
0.55
0.018
0.012
0.020
0.016
0.022
L
0.50
0.08
0.020
0.003
ddd
22/26
DocID024119 Rev 3
TS882, TS884
Package information
Figure 40. QFN16 3 x 3 mm (pitch 0.5 mm) footprint recommendation
ꢀꢁꢂꢃ
ꢃꢁꢀꢃ
ꢃꢁꢄꢀ
%
ꢀꢁꢂꢃ
ꢅꢁꢆꢇ
ꢃꢁꢅꢇ
ꢃꢁꢇꢃ
ꢅꢁꢆꢇ
$
DocID024119 Rev 3
23/26
26
Package information
TS882, TS884
4.5
TSSOP14 package information
Figure 41. TSSOP14 package outline
'
(ꢀ
$ꢀ $ꢂ
$
F
E
DDDꢃꢃꢃ&
ꢀꢁ
ꢄ
6($7,1*ꢃ
3/$1(
ꢆꢇꢂꢈꢃPP
*$*(ꢃ3/$1(
&
(
N
3,1ꢃꢀꢃ,'(17,),&$7,21
/
ꢀ
ꢅ
/ꢀ
H
76623ꢀꢁ
Table 11. TSSOP14 package mechanical data
Dimensions
Symbol
Millimeters
Typ.
Inches
Typ.
Min.
Max.
Min.
Max.
A
1.20
0.15
1.05
0.30
0.20
5.10
6.60
4.50
0.047
0.006
0.041
0.012
A1
A2
b
0.05
0.80
0.19
0.09
4.90
6.20
4.30
0.002
0.031
0.007
0.004
0.193
0.244
0.169
0.004
0.039
1.00
c
0.0089
0.201
0.260
0.176
D
5.00
6.40
4.40
0.65
0.60
1.00
0.197
0.252
0.173
0.0256
0.024
0.039
E
E1
e
L
0.45
0°
0.75
0.018
0°
0.030
L1
k
8°
8°
aaa
0.10
0.004
24/26
DocID024119 Rev 3
TS882, TS884
Revision history
5
Revision history
Table 12. Document revision history
Changes
Date
Revision
18-Jan-2013
1
Initial release.
Added TS884 device to header, Description, and Table 1: Device
summary.
Updated title (added “quad” comparator).
Updated Features and Table 2 (ESD tolerance: “6 kV” HBM replaced
by “8 kV” HBM).
Updated Description in accordance with added TS884 device.
Added SO14, TSSOP14 and QFN16 3 x 3 mm package to Features,
figure on page 1, Section 4: Package information. and Table 1:
Device summary.
02-May-2013
2
Moved Figure 1: Pin connections TS882 (top view) to page 3.
Added Figure 2: Pin connections TS884 (top view).
Updated Table 2: Absolute maximum ratings (added TS884 device
RTHJA values).
Minor corrections throughout document.
14-Jul-2014
3
Updated Table 1: Device summary on page 1
DocID024119 Rev 3
25/26
26
TS882, TS884
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
ST PRODUCTS ARE NOT DESIGNED OR AUTHORIZED FOR USE IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE
SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B)
AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS
OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT
PURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN WRITING OF SUCH USAGE, UNLESS A PRODUCT IS
EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR “AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRY
DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS. PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE
DEEMED SUITABLE FOR USE IN AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2014 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
26/26
DocID024119 Rev 3
相关型号:
TS88915T
TS88915T [Updated 6/02. 19 Pages] Low Skew CMOS PLL Clock Driver. 3 state 70 and 100 MHZ versions
ETC
TS88915TCRD/T100
PLL Based Clock Driver, 7 True Output(s), 1 Inverted Output(s), CMOS, CPGA29, CERAMIC, PGA-29
ATMEL
TS88915TCRD/T70
PLL Based Clock Driver, 7 True Output(s), 1 Inverted Output(s), CMOS, CPGA29, CERAMIC, PGA-29
ATMEL
TS88915TMR70
PLL Based Clock Driver, 8 True Output(s), 0 Inverted Output(s), CMOS, CPGA29, CERAMIC, PGA-29
ATMEL
TS88915TMRB/T70
PLL Based Clock Driver, 8 True Output(s), 0 Inverted Output(s), CMOS, CPGA29, CERAMIC, PGA-29
ATMEL
TS88915TMRD/T70
PLL Based Clock Driver, 8 True Output(s), 0 Inverted Output(s), CMOS, CPGA29, CERAMIC, PGA-29
ATMEL
TS88915TMW100
PLL Based Clock Driver, 8 True Output(s), 0 Inverted Output(s), CMOS, CQCC28, CERAMIC, LCC-28
ATMEL
©2020 ICPDF网 联系我们和版权申明