PIA2313SP750MN [SUPERWORLD]
Molded Choke Coil;
| 型号： | PIA2313SP750MN |
| 厂家： | 
SUPERWORLD ELECTRONICS |
| 描述： | Molded Choke Coil |
| 文件： | 总7页 (文件大小：266K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
P1
Molded Choke Coil – PIA2313SP Series
1. Part No. Expression:
P I A 2 3 1 3 S P 1 R 5 M N
a) Series Code
d) Inductance Code
e) Tolerance Code
(a)
(b)
(c) (d) (e)(f)
b) Dimension Code
c) Type Code
f) Internal Control Code
2. Configuration & Dimensions:
C
A
A`
D
L
Marking
D/C
G
Recommend PC Board Pattern
Note:
1. The above PCB layout is for reference only.
2. Solder paste thickness of 0.20mm and above is recommended.
3. Marking: Top row – Inductance code, Bottom row – YYWW
Unit: mm
A
A’
B
C
D
E
G
H
L
12.5 Ref. 19.6 Ref. 24.0 Ref.
23.5±0.5 22.7±0.3 22.0±0.3 12.6±0.4 5.0±0.4 19.0±0.3
3. Schematic:
4. Material List:
a) Core
b) Wire
c) Terminal
d) Ink
NOTE: Specifications subject to change without notice. Please check our website for latest information.
Proprietary and Confidential
Document of Superworld
31/01/2018
P2
Molded Choke Coil – PIA2313SP Series
5. General Specification:
(a) Operating Temp. : -40°C to +125°C (Inclusive of coil temp rise)
(b) Storage Temp. : -40°C to +125°C (on board)
(c) Humidity Range : 85 ± 2% RH
(d) Heat Rated Current (Irms) will cause the coil temperature rise approximately ∆t of 40°C (keep 1min)
(e) Saturation Current (Isat Typ.) will cause L0 to drop approximately 30%.
(f) Part Temp. (Ambient + Temp. Rise) should not exceed 125°C under worst case operating conditions.
(g) Storage condition (component in its packaging)
i)
Temperature: Less than 40°C
Humidity : 60% RH
ii)
6. Electrical Characteristics:
Heat Rating
Current DC
( A ) Irms.
Saturation
Current DC
(A) Isat.
Inductance
Test
Lo (uH)
DCR
DCR
Part Number
Frequency, L
@ 0A
±20%
(mΩ)Typ. (mΩ)Max.
(Hz)
Typ.
62
Max. Typ. Max.
PIA2313SP1R5MN
PIA2313SP2R0MN
PIA2313SP2R2MN
PIA2313SP3R0MN
PIA2313SP3R3MN
PIA2313SP4R7MN
PIA2313SP6R8MN
PIA2313SP100MN
PIA2313SP220MN
PIA2313SP230MN
PIA2313SP330MN
PIA2313SP470MN
PIA2313SP680MN
PIA2313SP750MN
PIA2313SP820MN
PIA2313SP101MN
1.50
2.00
2.20
3.00
3.30
4.70
6.80
10.0
22.0
23.0
33.0
47.0
68.0
75.0
82.0
100.0
1.0V/100K
1.0V/100K
1.0V/100K
1.0V/100K
1.0V/100K
1.0V/100K
1.0V/100K
1.0V/100K
1.0V/100K
1.0V/100K
1.0V/100K
1.0V/100K
1.0V/100K
1.0V/100K
1.0V/100K
1.0V/100K
57
54
52
48
47
44
36
30
18
18
16
14
12
11
10
9.5
52
50
48
45
1.0
1.02
1.05
1.42
1.5
1.15
1.20
1.25
1.64
1.75
2.2
60
58
51
49
47
40
33
22
22
19
17
14
13
12
11
48
43
44
39
41
37
38
34
1.9
36
32
2.7
3.1
28
20
3.8
4.15
11
15
14
9.2
15
14
9.2
11
12
10.5
10
13.5
17.3
26.2
27.5
31
15.4
20.8
29.5
31.6
34.2
40
12
12
9.0
8.5
7.7
7.5
10.5
9.0
9.0
36
Notes:
1) At all times, the current supplied to the product should not exceed Isat Max. value.
NOTE: Specifications subject to change without notice. Please check our website for latest information.
Proprietary and Confidential
Document of Superworld
31/01/2018
P3
Molded Choke Coil – PIA2313SP Series
7. Characteristics Curves:
PIA2313SP2R2MN
PIA2313SP2R0MN
PIA2313SP1R5MN
PIA2313SP3R0MN
PIA2313SP3R3MN
PIA2313SP4R7MN
PIA2313SP6R8MN
PIA2313SP100MN
PIA2313SP220MN
PIA2313SP470MN
PIA2313SP230MN
PIA2313SP330MN
NOTE: Specifications subject to change without notice. Please check our website for latest information.
Proprietary and Confidential
Document of Superworld
31/01/2018
P4
Molded Choke Coil – PIA2313SP Series
PIA2313SP680MN
PIA2313SP750MN
PIA2313SP820MN
PIA2313SP101MN
NOTE: Specifications subject to change without notice. Please check our website for latest information.
Proprietary and Confidential
Document of Superworld
31/01/2018
P5
Molded Choke Coil – PIA2313SP Series
8. Soldering:
Mildly activated rosin fluxes are preferred. The minimum amount of solder can lead to damage from the
stresses caused by the difference in coefficients of expansion between solder, chip and substrate. Our
terminations are suitable for all re-flow soldering systems. If hand soldering cannot be avoided, the preferred
technique is the utilization of hot air.
8-1 Solder Re-flow:
Recommended temperature profiles for re-flow soldering in Figure 1.
8-2 Soldering Iron (Figure 2):
Products attachment with soldering iron is discouraged due to the inherent process control limitations.
In the event that a soldering iron must be employed the following precautions are recommended.
Note :
a) Preheat circuit and products to 150°C.
b) 355°C tip temperature (Max.)
c) Never contact the ceramic with the iron tip
d) 1.0mm tip diameter (Max.)
e) Use a 20 watt soldering iron with tip diameter of 1.0mm
f) Limit soldering time to 4~5 secs.
NOTE: Specifications subject to change without notice. Please check our website for latest information.
Proprietary and Confidential
Document of Superworld
31/01/2018
P6
Molded Choke Coil – PIA2313SP Series
9. Packaging Information:
9-1 Reel Dimension:
2.0±0.5
COVER TAPE
A
EMBOSSED CARRIER
Type
A(mm)
B(mm)
C(mm)
D(mm)
330
13”x44mm 44.4+2/-0 100±2 13+0.5/-0.2
9-2 Tape Dimension:
Blank portions
Chip cavity
T
Blank portions
4.0
K0
P
200mm or more
400mm or more
A0
Direction of tape
Series Size Bo(mm) Ao(mm) Ko(mm) P(mm)
W(mm)
F(mm)
T(mm)
D(mm)
PIA 2313 25.0±0.1 23.0±0.1 13.6±0.1 32.0±0.1 44.0±0.3 20.2±0.1 0.5±0.05 1.5±0.1
9-3 Packaging Quantity:
PIA
2313
120
120
480
Chip / Reel
Inner box
Carton
NOTE: Specifications subject to change without notice. Please check our website for latest information.
Proprietary and Confidential
Document of Superworld
31/01/2018
P7
Molded Choke Coil – PIA2313SP Series
9-4 Tearing Off Force:
The force for tearing off cover tape is 10 to 130 grams in the
arrow direction under the following conditions.
Room
Humidity
(%)
Tearing
Speed
mm/min
Room Temp.
Room atm
(hPa)
(℃)
5~35
45~85
860~1060
300
Application Notice:
1. Storage Conditions:
To maintain the solderabililty of terminal electrodes:
a) Recommended products should be used within 12 months from the time of delivery.
b) The packaging material should be kept where no chlorine or sulfur exists in the air.
2. Transportation:
a) Products should be handled with care to avoid damage or contamination from perspiration and skin oils.
b) Vacuum pick up is strongly recommended for individual components.
c) Bulk handling should ensure that abrasion and mechanical shock are minimized.
NOTE: Specifications subject to change without notice. Please check our website for latest information.
Proprietary and Confidential
Document of Superworld
31/01/2018
相关型号：
©2020 ICPDF网 联系我们和版权申明