PIB0402MPR47MN [SUPERWORLD]

MOLDED POWER CHOKE COIL; 模压POWER CHOKE COIL


型号：	PIB0402MPR47MN
厂家：	SUPERWORLD ELECTRONICS
描述：	MOLDED POWER CHOKE COIL 模压POWER CHOKE COIL
文件：	总8页 (文件大小：363K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

MOLDED POWER CHOKE COIL

PIB0402MP SERIES

1. PART NO. EXPRESSION :

(a) Series code

(b) Dimension code

(d) Inductance code : 1R0 = 1.0uH

P I B 0 4 0 2 M P 1 R 0 M N -

(e) Tolerance code : M = ± 20%, Y = ± 30%

(a)

(b) (c)

(d) (e) (f)

(g)

(f) No coating

(g) Internal control number : 11 ~ 99

2. CONFIGURATION & DIMENSIONS :

1R0

Unit:m/m

4.45± 0.25 4.06± 0.25 1.8± 0.2 0.76± 0.30 2.0± 0.20

3. SCHEMATIC :

4. MATERIALS :

(a) Core : Alloy metal powder or equivalent

(b) Wire : Polyester wire or equivalent

(d) Ink : Halogen-free ketone

5. GENERAL SPECIFICATION :

a) Test Freq. : L : 100KHz/1V

b) Ambient Temp. : 25° C

c) Operating Temp. : -40° C to +125° C

d) Storage Temp. : -10° C to +40° C

Halogen

Free

e) Humidity Range : 50 ~ 60% RH (Product without taping)

f) Heat Rated Current (Irms) : Will cause the coil temp. rise approximately ǻt of 40°C (keep 1min.)

g) Saturation Current (Isat) : Will cause L0 to drop 30% typical (keep quickly)

h) Part Temperature (Ambient+Temp. Rise) : Should not exceed 125° C under worst case operating conditions.

NOTE : Specifications subject to change without notice. Please check our website for latest information.

25.02.2011

SUPERWORLD ELECTRONICS (S) PTE LTD

PG. 1

MOLDED POWER CHOKE COIL

PIB0402MP SERIES

6. ELECTRICAL CHARACTERISTICS :

Inductance L0

( µH )

Irms

( A )

Typ.

Isat

( A )

Typ.

DCR

Part No.

( mȍ )

@ 0 A

Typ. @ 25° C Max. @ 25° C

PIB0402MPR22YN

PIB0402MPR47MN

PIB0402MPR68MN

PIB0402MP1R0MN

PIB0402MP2R2MN

PIB0402MP3R3MN

PIB0402MP4R7MN

PIB0402MP6R8MN

0.22 ± 30%

0.47 ± 20%

0.68 ± 20%

1.00 ± 20%

2.20 ± 20%

3.30 ± 20%

4.70 ± 20%

6.80 ± 20%

9.0

7.5

7.0

4.5

3.5

2.5

2.6

2.1

12.5

9.5

8.5

7.0

5.0

4.0

3.2

2.5

6.0

6.6

141

162

Halogen

Free

NOTE : Specifications subject to change without notice. Please check our website for latest information.

25.02.2011

SUPERWORLD ELECTRONICS (S) PTE LTD

PG. 2

MOLDED POWER CHOKE COIL

PIB0402MP SERIES

7. CHARACTERISTICS CURVES :

PIB0402MPR22MN

TMPB0402MP-R22

PIB0402MPR47MN

TMPB0402MP-R47

0.4

0.3

0.2

0.1

0.8

0.6

0.4

0.2

2.5

7.5

12.5

1.9

3.8

5.7

7.6

9.5

DC CURRENT(A)

PIB0402MP1R0MN

TMPB0402MP-1R0

PIB0402MPR68MN

TMPB0402MP-R68

1.6

1.2

0.8

0.4

1.2

0.9

0.6

0.3

1.4

2.8

4.2

5.6

1.7

3.4

5.1

6.8

8.5

DC CURRENT(A)

PIB0402MP2R2MN

TMPB0402MP-2R2

PIB0402MP3R3MN

TMPB0402MP-3R3

4.5

1.5

DC CURRENT(A)

Halogen

Free

NOTE : Specifications subject to change without notice. Please check our website for latest information.

25.02.2011

SUPERWORLD ELECTRONICS (S) PTE LTD

PG. 3

MOLDED POWER CHOKE COIL

PIB0402MP SERIES

7. CHARACTERISTICS CURVES :

PIB0402MP4R7MN

TMPB0402MP-4R7

PIB0402MP6R8MN

TMPB0402MP-6R8

3.2

0.5

1.5

2.5

0.8

1.6

2.4

DC CURRENT(A)

Halogen

Free

NOTE : Specifications subject to change without notice. Please check our website for latest information.

25.02.2011

SUPERWORLD ELECTRONICS (S) PTE LTD

PG. 4

MOLDED POWER CHOKE COIL

PIB0402MP SERIES

8. RELIABILITY AND TEST CONDITION

ITEM

PERFORMANCE

TEST CONDITION

Electrical Characteristics Test

HP4284A, CH11025, CH3302, CH1320, CH1320S

LCR meter.

Inductance

Refer to standard electrical characteristics list

DCR

CH16502, Agilent33420A Micro-Ohm Meter.

Heat Rated Current (Irms)

Irms(A) will cause the coil temperature rise

approximately ǻT of 40°C without core loss

1. Applied the allowed DC current(keep 1min).

2. Temperature measured by digital surface thermometer

Saturation Current (Isat)

Reliability Test

ǻL30% typical

Isat(A) will cause Lo to drop

Electric specification should be satisfied

Temperature : 125± 2° C

Time : 1000± 12hrs

Measured at room temperature after placing for 2 to 3hrs

High

Temperature Test

(MIL-PRF-27)

Low

Temperature : -40± 2° C

Time :500± 12hrs

Measured at room temperature after placing for 2 to 3hrs

Temperature Test

Thermal Shock

Conditions of 1 cycle.

Step

Temperature (° C) Times (min.)

-40+0/-2

Room Temperature

+125+2/-0

15± 1

Within <0.2

15± 1

Total : 300 cycles

Measure at room temperature after placing for 2 to 3 hrs.

(AEC-Q200-REV C)

Humidity Resistance

Temperature : 85± 2° C

Humidity : 85± 3% RH

Time : 1000± 12hrs

Measured at room temperature after placing for 2 to 3hrs

(AEC-Q200-REV C)

Random Vibration

Test

Frequency : 10-2000-10Hz for 20 min.

Amplitude: Parts mounted within 2" from any secure point

Directions and times : X, Y, Z directions for 20 min.

This cycle shall be performed 12 times in each of three

mutually perpendicular directions.

(Total 12hours).

(MIL-STD-202 Method 204 D Test condition B)

Reflow Test

Solder test

Preheat : 150± 5° C

Duration : 5 minutes

Temperature : 260± 5° C, 20-40 seconds

(IPC/JEDEC J-STD-020C)

Terminals should be covered by over 95%

solder on visual inspection.

After dip into fluxˈdip into solder

235± 5° C, 4± 1seconds

Flux, solder for lead free

(ANSI/J-STD-002C Method B)

Halogen

Free

NOTE : Specifications subject to change without notice. Please check our website for latest information.

25.02.2011

SUPERWORLD ELECTRONICS (S) PTE LTD

PG. 5

MOLDED POWER CHOKE COIL

PIB0402MP SERIES

9. SOLDERING AND MOUNTING :

9-1. Recommended PC Board Pattern

5.2

2.2

9-2. Soldering

Mildly activated rosin fluxes are preferred. The minimum amount of solder can lead to damage from the stresses caused

by the difference in coefficients of expansion between solder, chip and substrate. Our terminations are suitable for all

wave and re-flow soldering systems. If hand soldering cannot be avoided, the preferred technique is the utilization of hot

air soldering tools.

9-2.1 Solder Re-flow :

Recommended temperature profiles for re-flow soldering in Figure 1.

9-2.2 Soldering Iron (Figure 2) :

Products attachment with soldering iron is discouraged due to the inherent process control limitations.

In the event that a soldering iron must be employed the following precautions are recommended.

Note :

a) Preheat circuit and products to 150° C.

b) 355° C tip temperature (max)

c) Never contact the ceramic with the iron tip

d) 1.0mm tip diameter (max)

e) Use a 20 watt soldering iron with tip diameter of 1.0mm

f) Limit soldering time to 4-5 secs.

Preheating

Soldering

20~40s

Natural

cooling

Preheating

Soldering

Natural

cooling

350

150

TP(260° C/40s max.)

217

200

150

60~150s

60~180s

480s max.

Gradual

Cooling

Time(sec.)

Over 1min.

Within 4-5s

Figure 1. Re-flow Soldering

Figure 2. Iron Soldering

Halogen

Free

NOTE : Specifications subject to change without notice. Please check our website for latest information.

25.02.2011

SUPERWORLD ELECTRONICS (S) PTE LTD

PG. 6

MOLDED POWER CHOKE COIL

PIB0402MP SERIES

10. PACKAGING INFORMATION :

10-1. Reel Dimension

COVER TAPE

2.0± 0.5

EMBOSSED CARRIER

Type

A(mm)

B(mm)

C(mm)

D(mm)

330

13" x 12mm 12.0± 0.5 100± 2.0 13.5± 0.5

10-2 Tape Dimension

4.0

2.0

Ø1.5

Series

Ao(mm)

Bo(mm)

Ko(mm)

2.3± 0.1

P(mm)

W(mm)

F(mm)

t(mm)

PIB0402MP

4.41± 0.1 5.0± 0.1

8.0± 0.1 12.0± 0.3 5.5± 0.1 0.35± 0.05

10-3. Packaging Quantity

Size

PIC0402HP

3000

Chip / Reel

Inner Box

Carton

Halogen

Free

6000

24000

NOTE : Specifications subject to change without notice. Please check our website for latest information.

25.02.2011

SUPERWORLD ELECTRONICS (S) PTE LTD

PG. 7

MOLDED POWER CHOKE COIL

PIB0402MP SERIES

10-4. Tearing Off Force

The force for tearing off cover tape is 10 to 130 grams

in the arrow direction under the following conditions.

(referenced ANSI/EIA-481-C-2003 of 4.11 standard)

180°

165° to

Room Temp.

(° C)

Room Humidity

(%)

Room atm Tearing Speed

Top cover tape

(hPa)

(mm/min)

5~35

45~85

860~1060

300

Base tape

Application Notice

1. Storage Conditions :

To maintain the solderabililty of terminal electrodes :

a) Temperature and humidity conditions : Less than 30° C and 70% RH.

b) Recommended products should be used within 6 months from the time of delivery.

c) The packaging material should be kept where no chlorine or sulfur exists in the air.

2. Transportation :

a) Products should be handled with care to avoid damage or contamination from perspiration and skin oils.

b) The use of tweezers or vacuum pick up is strongly recommended for individual components.

c) Bulk handling should ensure that abrasion and mechanical shock are minimized.

Halogen

Free

NOTE : Specifications subject to change without notice. Please check our website for latest information.

25.02.2011

SUPERWORLD ELECTRONICS (S) PTE LTD

PG. 8

相关型号：