WBB [SYSTEMSENSOR]
Weatherproof Back Box Accessory; 防水底盒配件型号: | WBB |
厂家: | SYSTEMSENSOR ADVANCED IDEAS. |
描述: | Weatherproof Back Box Accessory |
文件: | 总1页 (文件大小:148K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
INSTALLATION AND MAINTENANCE INSTRUCTIONS
WBB
Weatherproof Back Box
Accessory
3825 Ohio Avenue, St. Charles, Illinois 60174
1-800-SENSOR2, FAX: 630-377-6495
www.systemsensor.com
Specifications
This accessory is UL listed for use with:
Dimensions:
Box:
• H12/24K, S1224MCK, P1224MCK, and P12015K series
®
4.33″Lꢀ× 1.55″Wꢀ× 4.33″H
SpectrAlert wall horn, strobe and horn/strobe models
Foam gasket:
Conduit opening: (2) 1⁄
0.125″ thick, adheres to box top
• SSM24 and SSV120 series alarm bells
2
″ NPT, fully threaded with
(2) 1⁄
2
″ꢀNPT plug, (1) 7⁄
8″ꢀknockout plug Refer to specific model installation instructions for weath-
Rear mounting tabs with 0.25″ diameter eyelets
Top mounting holes, #8-32 × 0.50″ DP
erproof rating, temperature operating range, indoor and
outdoor application information.
Mounting Instructions
Figure 1: SpectrAlert horn, strobe, and horn/strobe
(‘K’ suffix models) mounting with universal plate
Figure 2: Typical SSM and SSV bell weatherproof
installation
GASKET
WBB
Plate
WBB
Flat Head
Screw (4 total)
CONDUIT
ENTRANCE
Gasket
Conduit
Slot
Entrance
PAN HEAD SCREW
(4 TOTAL)
Locking Rib
Paper Liner
For Plate
Gasket
W0169-01
1. Mount back box in desired location (See Figure 2).
A0135-01
1
2. Install ⁄
2
″ꢀNPT plug into unused conduit opening.
1. Mount back box in desired location (See Figure 1).
1
3. For SSM24 and SSV120 alarm bells, remove gong (refer
to SSM and SSV bell series installation manual) and
complete field wiring.
2. Install ⁄
3. For SpectrAlert models, mount plate to back box using 4
#8-32 x 1⁄
″ screws (Figure 1)supplied with product.
2
″ꢀNPT plug into unused conduit opening.
2
4. Mount bell to WBB with 4 #8-32 x 3⁄
4″ꢀscrews (Figure 2)
4. Complete field wiring.
supplied with product.
5. Remove paper liner on plate gasket – NOTE: Perform elec-
trical tests first, then remove liner. Paper liner must be
removed from gasket before final installation.
6. Insert locking rib into slot on plate.
7. Press into plate; the SpectrAlert model will make a
“click” when it has locked into place.
Figure 3: Knockout plug removal
1. If a rear conduit entry
is required, remove the
knockout plug using a
flat blade screwdriver as
shown in Figure 3. Strike
sharply with a hammer
to pierce the wall of the
knockout plug. Move to
an adjacent wall section
NOTE: The weatherproof or outdoor notification appli-
ance must be used with the System Sensor
WBB back box when installed in applications
requiring the appliance to be weatherproof or
outdoor-listed. In such applications, using a back
box other than the System Sensor WBB will void
the UL designation.
A0134-00
and repeat until the plug falls out. Make sure that the
back box is supported adequately during this operation
to avoid injury.
NOTE: All System Sensor weatherproof wall-mount
horns and horn/strobes can be surface mounted
or flush mounted when used with the System
Sensor WBB.
2. To meet weatherproof or outdoor listing, the conduit
entrance must be gasketed.
1
3. Install ⁄
2
″ꢀNPT plugs (2) into unused conduit openings.
D770-41-00
1
I56-1893-005
2004 System Sensor
©
相关型号:
WBC-B0202AG-01-1002-B
Wire Bondable Chip ResistorsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TTELEC
WBC-B0202AG-01-1002-C
Wire Bondable Chip ResistorsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TTELEC
WBC-B0202AG-01-1002-D
Wire Bondable Chip ResistorsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TTELEC
WBC-B0202AG-01-1002-F
Wire Bondable Chip ResistorsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TTELEC
WBC-B0202AG-01-1002-G
Wire Bondable Chip ResistorsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TTELEC
WBC-B0202AG-01-1002-J
Wire Bondable Chip ResistorsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TTELEC
WBC-B0202AG-01-1002-K
Wire Bondable Chip ResistorsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TTELEC
WBC-B0202AS-01-1002-B
Wire Bondable Chip ResistorsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TTELEC
WBC-B0202AS-01-1002-C
Wire Bondable Chip ResistorsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TTELEC
WBC-B0202AS-01-1002-D
Wire Bondable Chip ResistorsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TTELEC
WBC-B0202AS-01-1002-F
Wire Bondable Chip ResistorsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TTELEC
WBC-B0202AS-01-1002-G
Wire Bondable Chip ResistorsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TTELEC
©2020 ICPDF网 联系我们和版权申明