B84114D0000B020 [TDK]

Single Phase EMI Filter, 250V, 50/60HzHz,;


型号：	B84114D0000B020
厂家：	TDK ELECTRONICS
描述：	Single Phase EMI Filter, 250V, 50/60HzHz, LTE
文件：	总10页 (文件大小：421K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

EMC filters

2-line filters

SIFI-D for high insertion loss

Series/Type:

B84114D

Date:

May 2014

information contained therein without EPCOS' prior express consent is prohibited.

EPCOS AG is a TDK Group Company.

2-line filters

B84114D

SIFI-D for high insertion loss

Power line filters for 1-phase systems

Rated voltage V_R: 250 V AC/DC

Rated current I_R: 1 A to 10 A

Construction

2-line filters

Metal case

Polyurethane potting (UL 94 V-0)

Features

Easy to install

Compact design

Optimized leakage current

ENEC, UL and cUL approval

Typical applications

Switch-mode power supplies

Industrial electronics

Telecommunications

Data systems

DC applications

Terminals

Tab connectors

Marking

Marking on component:

Manufacturer's logo, ordering code, rated voltage, rated

current, rated temperature, climatic category, date code,

approvals

Minimum data on packaging:

Manufacturer's logo, ordering code, quantity, date code

Circuit diagram

Please read Cautions and warnings and

Important notes at the end of this document.

Page 2 of 10

2-line filters

B84114D

SIFI-D for high insertion loss

Technical data and measuring conditions

Rated voltage V_R

Rated current I_R

Test voltage V_test

250 V AC (50/60 Hz) / 250 V DC

Referred to 40 °C rated temperature

1414 V DC, 2 s (line/line)

2700 V DC, 2 s (lines/case)

Climatic category (IEC 60068-1)

Approvals

25/085/21 (ꢀ25 °C/+85 °C/21 days damp heat test)

IEC 60939, UL 1283, CSA C22.2 No.8

Characteristics and ordering codes

C_R

µF

C_R

Approvals

I_R

L_R

I_LK

Approx. Ordering code

weight

V_R= 250 V AC/DC

2 × 0.47

2 × 0.68

2 × 4700

2 × 5.6

2 × 4.7

0.369 150

0.369 230

0.369 420

B84114D0000A010

B84114D0000B010

B84114D0000A020

B84114D0000B020

B84114D0000A030

B84114D0000B030

B84114D0000A060

B84114D0000B060

B84114D0000A110

B84114D0000B110

× = Approval granted

Cases and dimensions

I_R

Dimensions (mm)

b₁

b₂

b₃

b₄

l₁

l₂

l₃

l₄

h₁

h₂

ꢀ

50.8

31.5

60.4

ꢀ

63.5

89.5

28.6

74.7

84.5

ꢀ

50.8

31.5

60.4

ꢀ

63.5

89.5

28.6

74.7

84.5

ꢀ

50.8

31.5

60.4

ꢀ

63.5

89.5

28.6

74.7

84.5

ꢀ

50.8

31.5

60.4

ꢀ

75.5

101.5 31.8

87.1

See dimensional drawing

Please read Cautions and warnings and

Important notes at the end of this document.

Page 3 of 10

2-line filters

B84114D

SIFI-D for high insertion loss

B84114D0000A010 ... A60 (1 A ... 6 A)

B84114D0000A110 (10 A)

General tolerances according to ISO 2768ꢀcL General tolerances according to ISO 2768ꢀcL

Dimensions in mm Dimensions in mm

B84114D0000B010 ... B60 (1 A ... 6 A) B84114D0000B110 (10 A)

General tolerances according to ISO 2768ꢀcL General tolerances according to ISO 2768ꢀcL

Dimensions in mm Dimensions in mm

Please read Cautions and warnings and

Important notes at the end of this document.

Page 4 of 10

2-line filters

B84114D

SIFI-D for high insertion loss

Insertion loss (typical values at Z = 50 Ω)

Filters for 1 A, 2 A and 3 A

Filters for 6 A

Filters for 10 A

Please read Cautions and warnings and

Important notes at the end of this document.

Page 5 of 10

2-line filters

B84114D

SIFI-D for high insertion loss

Cautions and warnings

Please read all safety and warning notes carefully before installing the EMC filter and putting it

into operation (see ). The same applies to the warning signs on the filter. Please ensure that

the signs are not removed nor their legibility impaired by external influences.

Death, serious bodily injury and substantial material damage to equipment may occur if the

appropriate safety measures are not carried out or the warnings in the text are not observed.

Using according to the terms

The EMC filters may be used only for their intended application within the specified values in low-

voltage networks in compliance with the instructions given in the data sheets and the data book.

The conditions at the place of application must comply with all specifications for the filter used.

Warning

It shall be ensured that only qualified persons (electricity specialists) are engaged on work such

as planning, assembly, installation, operation, repair and maintenance. They must be provided

with the corresponding documentation.

Danger of electric shock. EMC filters contain components that store an electric charge. Danger-

ous voltages can continue to exist at the filter terminals for longer than five minutes even after

the power has been switched off.

The protective earth connections shall be the first to be made when the EMC filter is installed

and the last to be disconnected. Depending on the magnitude of the leakage currents, the par-

ticular specifications for making the protective-earth connection must be observed.

Impermissible overloading of the EMC filter or filter, such as with circuits able to cause reso-

nances, impermissible voltages at higher frequencies etc. can lead to bodily injury and death as

well as cause substantial material damages (e.g. destruction of the filter housing).

EMC filters and filters must be protected in the application against impermissible exceeding of

the rated currents by overcurrent protective circuitry.

In case of leakage currents >3.5 mA you shall mount the PE conductor stationary with the

required cross section before beginning of operation and save it against disconnecting. For

leakage currents I_L¹⁾<10 mA the PE conductor must have a KU value²⁾of 4.5 A³⁾; for leakage

currents I_L≥10 mA the PE conductor must have a KU value of 6.⁴⁾

Output chokes and output filters must be protected in the application against impermissible

exceeding of the component temperature.

The converter output frequency must be within the specified range to avoid resonances and

uncontrolled warming of the output chokes and output filters.

1) I_L= leakage current let-go

2) The KU value (symbol KU) is a classification parameter of safety-referred failure types designed to ensure protection against hazardous

body currents and excessive heating.

3) A value of KU = 4.5 with respect to interruptions is attained with: a) a permanently connected protective earth circuit ≥2.5 mm²

connected via shroud connectors (IEC 60309ꢀ2) and b) a protective earth circuit.

4) KU = 6 with respect to interruptions is achieved for fixedꢀconnection lines ≥10 mm²where the type of connection and line layout

correspond to the requirements for PEN conductors as specified in relevant standards.

Please read Cautions and warnings and

Important notes at the end of this document.

Page 6 of 10

2-line filters

B84114D

SIFI-D for high insertion loss

The table below summarizes the safety instructions that must be observed without fail. A detailed

description can be found in the relevant chapters of the databook.

Topic

Instructions

Reference chapter

(data book),

paragraph

Selecting a filter

When selecting a filter, it is mandatory to observe the Selection guide for

rated data of the equipment (such as its rated input

current, rated voltage, harmonic content etc.) as well

as the derating instructions in Chapters 9 and 10.

converter filters

Rated voltage

When power distribution systems deviating from the

Power distribution

symmetric TN-S system it is to check the suitability of systems,

the EMC filters and the allowed voltages including the

fault cases.

Protection from

residual voltages

Discharge resistors

Active parts must be discharged within 5 s to a Safety regulations,

voltage of less than 60 V (or 50 µ C). If this limit 6.1

cannot be observed due to the operating mode, the

hazardous point must be permanently marked in a

clearly visible way.

Filters which are not permanently connected (e.g.

when the test voltage is applied to the filter at the

incoming goods inspection) must be discharged after

the voltage has been switched off.

Safety regulations,

6.2

Installing and

removing of EMC

filters

When installing and removing our EMC filters, a Safety regulations,

voltage-free state must be set up and secured with 6.4

observance of the five safety rules described in

EN 50110-1.

Installation

Use in IT systems

The special features of the IT system ("first fault case" Power distribution

and other fault cases) shall be observed.

system (network

types), 7.6

Safety notes on

leakage currents

The filter leakage currents specified in the data book Leakage current,

are intended for user information only.The maximum 8.4

leakage current of the entire electrical equipment or Leakage current,

appliance has to be limited for safety reasons. Please 8.6

obtain the applicable limits for your application from

the relevant regulations, provisions and standards.

Voltage derating

If the permissible limits for the higher-frequency Voltage derating,

voltages at the filter are exceeded, the filter may be 9.8

damaged or destroyed.

Hazards caused by

overloading the filters

Current derating at

elevated ambient

temperatures

Non-observance of the current derating may lead to Current derating,

overheating and consequently represents

hazard.

a fire 10.1

Please read Cautions and warnings and

Important notes at the end of this document.

Page 7 of 10

2-line filters

B84114D

SIFI-D for high insertion loss

Topic

Instructions

Reference chapter

(data book),

paragraph

Protective earth

connection at

operating currents

>250 A

For operating currents greater than 250 A, we Mounting

recommend the PE connection to be set up between instructions, point

the feed (filter: line) and output (filter: load) not via the

PE terminal bolt in the filter housing.

Mounting position

Note the mounting position of the filters! It must Mounting

always be ensured that natural convection is not instructions, point

impaired.

Long motor cables

Long motor cables cause parasitic currents in the

Mounting

installation. The cable lengths indicated for the output instructions, point

chokes and output filters serve for orientation. The

user must check the technical parameters and

especially the choke temperatures for the respective

application.

Display of ordering codes for EPCOS products

The ordering code for one and the same product can be represented differently in data sheets,

data books, other publications and the website of EPCOS, or in order-related documents such as

shipping notes, order confirmations and product labels. The varying representations of the

ordering codes are due to different processes employed and do not affect the specifications of the

respective products. Detailed information can be found on the Internet under

www.epcos.com/orderingcodes

Please read Cautions and warnings and

Important notes at the end of this document.

Page 8 of 10

2-line filters

B84114D

SIFI-D for high insertion loss

Symbols and terms

Symbol

English

German

Insertion loss

Einfügungsdämpfung

C_R

C_X

C_Y

∆V

dv/dt

Rated capacitance

Capacitance X capacitor

Capacitance Y capacitor

Voltage drop (input to output)

Rate of voltage rise

Frequency

Bemessungskapazität

Kapazität X-Kondensator

Kapazität Y-Kondensator

Spannungsabfall im Filter

Spannungsanstiegsgeschwindigkeit

Frequenz

f_M

f_P

Converter output frequency

Pulse frequency

Motorfrequenz

Pulsfrequenz

f_R

f_res

I_C

I_LK

I_max

I_N

Rated frequency

Bemessungsfrequenz

Resonanzfrequenz

Strom durch Kondensator

Filter-Ableitstrom

Maximalstrom

Nennstrom

Resonant frequency

Current through capacitor

Filter leakage current

Maximum current

Nominal current

I_op

I_pk

I_q

I_R

I_S

Operating current (design current)

Rated peak withstand current

Capacitive reactive current

Rated current

Interference current

Inductance

Betriebsstrom

Bemessungs-Stoßstromfestigkeit

Kapazitiver Blindstrom

Bemessungsstrom

Störstrom

Induktivität

L_R

L_stray

P_L

Rated inductance

Stray inductance

Power loss

Resistance

Bemessungsinduktivität

Streuinduktivität

Verlustleistung

Widerstand

R_is

R_typ

T_A

T_max

T_min

T_R

u_k

V_eff

V_K

V_LE

V_N

V_R

V_peak

V_test

V_X

V_Y

X_L

Insulation resistance

DC resistance, typical value

Ambient temperature

Upper category temperature

Lower category temperature

Rated temperature

Refered voltage drop in %

RMS voltage

Isolationswiderstand

Gleichstromwiderstand, Richtwert

Umgebungstemperatur

Obere Kategorietemperatur

Untere Kategorietemperatur

Bemessungstemperatur

Bezogener Spannungsabfall in %

Effektivspannung

Voltage drop

Spannungsabfall

Voltage line to earth; voltage line to ground Spannung Phase zu Erdpotential

Nominal voltage

Rated voltage

Peak voltage

Nennspannung

Bemessungsspannung

Spitzenspannung

Test voltage

Prüfspannung

Voltage over X capacitor

Voltage over Y capacitor

Inductive reactance

Impedance

Spannung über X-Kondensator

Spannung über Y-Kondensator

Induktiver Blindwiderstand

Scheinwidertand

|Z|

Impedance, absolute value

Scheinwiderstand (Betragswert)

Please read Cautions and warnings and

Important notes at the end of this document.

Page 9 of 10

Important notes

The following applies to all products named in this publication:

1. Some parts of this publication contain statements about the suitability of our products for

certain areas of application. These statements are based on our knowledge of typical re-

quirements that are often placed on our products in the areas of application concerned. We

nevertheless expressly point out that such statements cannot be regarded as binding

statements about the suitability of our products for a particular customer application.

As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar

with them than the customers themselves. For these reasons, it is always ultimately incum-

bent on the customer to check and decide whether an EPCOS product with the properties de-

scribed in the product specification is suitable for use in a particular customer application.

2. We also point out that in individual cases, a malfunction of electronic components or

failure before the end of their usual service life cannot be completely ruled out in the

current state of the art, even if they are operated as specified. In customer applications

requiring a very high level of operational safety and especially in customer applications in

which the malfunction or failure of an electronic component could endanger human life or

health (e.g. in accident prevention or lifesaving systems), it must therefore be ensured by

means of suitable design of the customer application or other action taken by the customer

(e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by

third parties in the event of malfunction or failure of an electronic component.

3. The warnings, cautions and product-specific notes must be observed.

4. In order to satisfy certain technical requirements, some of the products described in this

publication may contain substances subject to restrictions in certain jurisdictions (e.g.

because they are classed as hazardous). Useful information on this will be found in our Ma-

terial Data Sheets on the Internet (www.epcos.com/material). Should you have any more de-

tailed questions, please contact our sales offices.

5. We constantly strive to improve our products. Consequently, the products described in this

publication may change from time to time. The same is true of the corresponding product

specifications. Please check therefore to what extent product descriptions and specifications

contained in this publication are still applicable before or when you place an order. We also

reserve the right to discontinue production and delivery of products. Consequently, we

cannot guarantee that all products named in this publication will always be available. The

aforementioned does not apply in the case of individual agreements deviating from the fore-

going for customer-specific products.

6. Unless otherwise agreed in individual contracts, all orders are subject to the current ver-

sion of the "General Terms of Delivery for Products and Services in the Electrical In-

dustry" published by the German Electrical and Electronics Industry Association

(ZVEI).

7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CeraLink, CeraPlas, CSMP, CSSP,

CTVS, DeltaCap, DigiSiMic, DSSP, FilterCap, FormFit, MiniBlue, MiniCell, MKD, MKK,

MLSC, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, SIFERRIT, SIFI,

SIKOREL, SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV, SIP5D, SIP5K, TFAP,

ThermoFuse, WindCap are trademarks registered or pending in Europe and in other coun-

tries. Further information will be found on the Internet at www.epcos.com/trademarks.

Page 10 of 10

B84114D0000B020 [TDK]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB

SI9137LG

SI9122E