CLT32-R31 [TDK]
SMD/SMT 电感器(线圈);型号: | CLT32-R31 |
厂家: | TDK ELECTRONICS |
描述: | SMD/SMT 电感器(线圈) 电感器 |
文件: | 总7页 (文件大小:1143K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Inductors for power circuits
Size 3.2 x 2.5 x 2.5 (mm)
Series/Type:
CLT32
Date:
March 2022
TDK Electronics AG 2022. Reproduction, publication and dissemination of this publication, enclosures hereto
and the information contained therein without TDK Electronics’ prior express consent is prohibited.
Inductors for power circuits
Size 3.2 x 2.5 x 2.5 (mm)
CLT32
Construction
Thick copper frame
Molded metal solution
No internal connection
Features
High current, low DC resistance
Temperature range from –40 °C up to +165 °C incl. self-heating
ESD tested up to 2 kV to AEC-Q200
Suitable for lead-free reflow soldering as
referenced in JEDEC J-STD 020D
Qualified to AEC-Q200
RoHS-compatible
Applications
PMIC systems in automotive electronics
Terminals
Tinned terminals
Layer composition Ni, Sn
Lead-free tinned
Marking
No marking on component
Minimum data on reel:
Manufacturer, ordering code, lot number, quantity, date of packing
Delivery mode and packing unit
12-mm blister tape, wound on 330-mm Ø reel
Packing unit: 6000 pcs./reel
Please read Cautions and warnings and
Important notes at the end of this document.
2
3/22
Inductors for power circuits
Size 3.2 x 2.5 x 2.5 (mm)
CLT32
Dimensions
Layout recommendation
Taping an packing
Blister tape
Reel
Please read Cautions and warnings and
Important notes at the end of this document.
3
3/22
Inductors for power circuits
Size 3.2 x 2.5 x 2.5 (mm)
CLT32
Technical data and measuring conditions
Rated inductance LR
Inductance tolerance
Operating temperature range
Rated current Itemp
Measured with Agilent 4990A at 1 MHz, 0.1 V, +23 °C 3 °C
20% at +23 °C 3 °C
–40 °C … +165 °C
Based on the temperature increase
(temperature increase 40 K by self-heating)
Ambient temperature: +23 °C
Measured in 100 µm Cu thickness single layer
PCB 100x40x1 mm (equivalent to multilayer PCB)
Temperature rise is highly dependent on many factors and
consequently, it must be verified in final application
Based on the inductance change rate
Saturation current Isat
(30% below the initial value)
DC resistance RDC
Measured at +23 °C 3 °C; tolerance 15%
Sn95.5Ag3.8Cu0.7: +245 °C / 5 s
Solderability (lead-free)
Method:
Solder bath (Dip)
Wetting of soldering area: 95%
+260 °C, 40 s (as referenced in JEDEC J-STD 020D)
40/165/56 (to IEC 60068-1)
Resistance to soldering heat
Climatic category
Storage conditions
Mounted: –40 °C … +165 °C
Packaged: –25 °C … +40 °C, 75% RH
Approx. 120 mg
Weight
Characteristics and ordering codes
LR
RDC,typ
ISat,typ
at 23 °C
Itemp,typ
at 23 °C
Internal code
Ordering code
at +40 K temp. increase
nH
17
m
0.39
1.0
1.0
1.9
1.9
3.3
3.3
5.3
7.6
A
A
60.0
54.0
39.5
36.0
29.0
25.4
20.5
17.5
13.5
45.0
28.0
28.0
20.0
20.0
15.4
15.4
12.1
10.1
B82403T0170M000 CLT32-17N
B82403T0420M000 CLT32-42N
B82403T0550M000 CLT32-55N
B82403T0800M000 CLT32-80N
B82403T0111M000 CLT32-R11
B82403T0151M000 CLT32-R15
B82403T0201M000 CLT32-R20
B82403T0311M000 CLT32-R31
B82403T0441M000 CLT32-R44
42
55
80
110
150
200
310
440
Please read Cautions and warnings and
Important notes at the end of this document.
4
3/22
Inductors for power circuits
Size 3.2 x 2.5 x 2.5 (mm)
CLT32
Cautions and warnings
Please note the recommendations in our Inductors data book (latest edition) and in the data
sheets.
– Particular attention should be paid to the derating curves given there.
– The soldering conditions should also be observed. Temperatures quoted in relation to wave
soldering refer to the pin, not the housing.
If the components are to be washed varnished it is necessary to check whether the washing
varnish agent that is used has a negative effect on the wire insulation, any plastics that are used,
or on glued joints. In particular, it is possible for washing varnish agent residues to have a
negative effect in the long-term on wire insulation.
Washing processes may damage the product due to the possible static or cyclic mechanical
loads (e.g. ultrasonic cleaning). They may cause cracks to develop on the product and its parts,
which might lead to reduced reliability or lifetime.
The following points must be observed if the components are potted in customer applications:
– Many potting materials shrink as they harden. They therefore exert a pressure on the plastic
housing or core. This pressure can have a deleterious effect on electrical properties, and in
extreme cases can damage the core or plastic housing mechanically.
– It is necessary to check whether the potting material used attacks or destroys the wire, wire
insulation, plastics or glue.
– The effect of the potting material can change the high-frequency behaviour of the components.
– Many coating materials have a negative effect (chemically and mechanically) on the winding
wires, insulation materials and connecting points. Customers are always obligated to
determine whether and to what extent their coating materials influence the component.
Customers are responsible and bear all risk for the use of the coating material. TDK
Electronics does not assume any liability for failures of our components that are caused by the
coating material.
Ceramics / ferrites are sensitive to direct impact. This can cause the core material to flake, or
lead to breakage of the core.
Even for customer-specific products, conclusive validation of the component in the circuit can
only be carried out by the customer.
Due to product design and applied manufacturing process, appearance, symmetry, and shape
of not dimensioned details could vary within same lot, as well discoloration of housing is possible.
TDK does not expect detrimental effects on product function or reliability. In case of conflicts,
TDK reference standard shall prevail.
Display of ordering codes for TDK Electronics products
The ordering code for one and the same product can be represented differently in data sheets, data
books, other publications, on the company website, or in order-related documents such as shipping
notes, order confirmations and product labels. The varying representations of the ordering
codes are due to different processes employed and do not affect the specifications of the
respective products. Detailed information can be found on the Internet under
www.tdk-electronics.tdk.com/orderingcodes.
Please read Cautions and warnings and
Important notes at the end of this document.
5
3/22
Important notes
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical require-
ments that are often placed on our products in the areas of application concerned. We never-
theless expressly point out that such statements cannot be regarded as binding statements
about the suitability of our products for a particular customer application. As a rule, we
are either unfamiliar with individual customer applications or less familiar with them than the cus-
tomers themselves. For these reasons, it is always ultimately incumbent on the customer to
check and decide whether a product with the properties described in the product specification is
suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of electronic components or fail-
ure before the end of their usual service life cannot be completely ruled out in the current
state of the art, even if they are operated as specified. In customer applications requiring a
very high level of operational safety and especially in customer applications in which the mal-
function or failure of an electronic component could endanger human life or health (e.g. in acci-
dent prevention or life-saving systems), it must therefore be ensured by means of suitable de-
sign of the customer application or other action taken by the customer (e.g. installation of pro-
tective circuitry or redundancy) that no injury or damage is sustained by third parties in the event
of malfunction or failure of an electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this pub-
lication may contain substances subject to restrictions in certain jurisdictions (e.g. be-
cause they are classed as hazardous). Useful information on this will be found in our Material
Data Sheets on the Internet (www.tdk-electronics.tdk.com/material). Should you have any more
detailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order.
We also reserve the right to discontinue production and delivery of products. Consequent-
ly, we cannot guarantee that all products named in this publication will always be available. The
aforementioned does not apply in the case of individual agreements deviating from the foregoing
for customer-specific products.
6. Unless otherwise agreed in individual contracts, all orders are subject to our General Terms
and Conditions of Supply.
6
3/22
Important notes
7. Our manufacturing sites serving the automotive business apply the IATF 16949 standard.
The IATF certifications confirm our compliance with requirements regarding the quality manage-
ment system in the automotive industry. Referring to customer requirements and customer spe-
cific requirements (“CSR”) TDK always has and will continue to have the policy of respecting in-
dividual agreements. Even if IATF 16949 may appear to support the acceptance of unilateral re-
quirements, we hereby like to emphasize that only requirements mutually agreed upon can
and will be implemented in our Quality Management System. For clarification purposes we
like to point out that obligations from IATF 16949 shall only become legally binding if individually
agreed upon.
8. The trade names EPCOS, CarXield, CeraCharge, CeraDiode, CeraLink, CeraPad, CeraPlas,
CSMP, CTVS, DeltaCap, DigiSiMic, ExoCore, FilterCap, FormFit, LeaXield, MiniBlue, MiniCell,
MKD, MKK, ModCap, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap,
PowerHap, PQSine, PQvar, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SiMic, SIMID,
SineFormer, SIOV, ThermoFuse, WindCap, XieldCap are trademarks registered or pending
in Europe and in other countries. Further information will be found on the Internet at
www.tdk-electronics.tdk.com/trademarks.
Release 2020-06
7
3/22
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明