EV1406-1800-A [TDK]

µPOL™嵌入式DC-DC转换器;
EV1406-1800-A
型号: EV1406-1800-A
厂家: TDK ELECTRONICS    TDK ELECTRONICS
描述:

µPOL™嵌入式DC-DC转换器

DC-DC转换器
文件: 总15页 (文件大小:5856K)
中文:  中文翻译
下载:  下载PDF数据表文档文件
EV1406-1800-A  
EV1406-1800-A  
EVALUATION BOARD  
USER GUIDE  
Page 1  
Rev 1.2, Jun 10, 2020  
Patent Protected: US 9,729,059 B1; US 10,193,442 B2  
Copyright© 2018–20 TDK Corporation. All rights reserved.  
All registered trademarks and trademarks are the property of their respective owners.  
Data and specifications subject to change without notice.  
EV1406-1800-A  
Introduction  
This user guide describes the evaluation board provided for the FS1406 µPOL™ product.  
The board generates an output voltage (VOUT) of 1.8V for loads of 0–6A from an input voltage (PVIN) of 12V.  
Specifications  
Input voltage (PVIN) = +12V  
Output voltage (VOUT) = +1.8V  
Output load (IO) = 0–6A  
Switching frequency (FSW) = 1.9MHz  
Output capacitance (CO) = 2x22µF (MLCC)  
In put capacitance (CIN) = 2x22µF (MLCC)  
Dimensions (width x length x thickness) = 63 x 84 x 1.5mm  
Connections  
Name  
PVIN  
Gnd  
VOUT  
Gnd  
VCC  
Identifier  
J1  
Description  
Input voltage (+12V)  
Ground for input voltage  
Output voltage (+1.8V)  
Ground for output voltage  
Internal supply (VCC) – output of an LDO regulator  
Ground for internal supply  
Enable  
J2  
J8  
J7  
TP2  
TP3  
TP11  
TP12  
Gnd  
En  
PG  
Power Good  
The board is configured for a single input supply. An internal low drop-out regulator generates the internal supply (VCC)  
from PVIN. The Enable (En) input is connected to PVIN through a resistor divider, so that no Enable signal is needed.  
Operation  
To use the evaluation board:  
1. Connect a well-regulated +12V input supply to PVIN (J1) and Gnd (J2).  
2. Connect a load of 0–6A to VOUT (J8) and Gnd (J7).  
Page 2  
Rev 1.2, Jun 10, 2020  
Patent Protected: US 9,729,059 B1; US 10,193,442 B2  
Copyright© 2018–20 TDK Corporation. All rights reserved.  
All registered trademarks and trademarks are the property of their respective owners.  
Data and specifications subject to change without notice.  
EV1406-1800-A  
Description  
The evaluation board consists of a 4-layer PCB made from FR4 glass-reinforced epoxy laminate material. All layers use  
2oz copper (equating to a thickness of 0.0694mm). The major power components, including the FS1406, are mounted  
on the top side of the board.  
Part reference  
Quantity  
Type  
Description  
FS1406 µPOL  
1
1
2
1
1
2
1
1
2
1
2
1
2
5
1
2
17  
Main IC  
C9  
2.2µF  
22µF  
0.1µF  
68µF  
22µF  
1µF  
0402, 10V, X7S  
0805, 16V, X5R  
0402, 16V, X7R  
25V  
C10, C21  
C12  
C13  
C14, C15  
0805, 6.3V, X5R  
0603, 25V, X5R  
Banana connector  
Banana connector  
Banana connector  
3-pin header  
C26  
J1  
Red  
J2, J7  
Black  
Green  
J8  
J10, J11  
R1  
2.7  
49.9kΩ  
0Ω  
10%, 1/8W, 0805 case size  
10%, 1/8W, 0805 case size  
0402 case size  
R3, R7  
R4, R9, R11, R13, R17  
R6  
12.7kΩ  
4.99kΩ  
10%, 1/8W, 0805 case size  
0402 case size  
R18, R19  
TP1-TP12, SW/NC15, VBUS, VEXTBUS, SCL, SDA  
Test points  
Figure 1 shows the layout of the board and Figure 2 shows a schematic of the electrical circuit.  
Page 3  
Rev 1.2, Jun 10, 2020  
Patent Protected: US 9,729,059 B1; US 10,193,442 B2  
Copyright© 2018–20 TDK Corporation. All rights reserved.  
All registered trademarks and trademarks are the property of their respective owners.  
Data and specifications subject to change without notice.  
EV1406-1800-A  
Figure 1 Board layout  
Page 4  
Rev 1.2, Jun 10, 2020  
Patent Protected: US 9,729,059 B1; US 10,193,442 B2  
Copyright© 2018–20 TDK Corporation. All rights reserved.  
All registered trademarks and trademarks are the property of their respective owners.  
Data and specifications subject to change without notice.  
 
EV1406-1800-A  
Figure 2 Schematic  
Page 5  
Rev 1.2, Jun 10, 2020  
Patent Protected: US 9,729,059 B1; US 10,193,442 B2  
Copyright© 2018–20 TDK Corporation. All rights reserved.  
All registered trademarks and trademarks are the property of their respective owners.  
Data and specifications subject to change without notice.  
 
EV1406-1800-A  
Typical performance  
Figure 3 to Figure 17 show typical operating waveforms for the evaluation board, while Figure 18 shows a  
thermal image of the board in operation. In all cases, the board is operating at room temperature with no  
airflow; PVIN is 12V, VOUT is 1.8V and IO is 0–6A.  
Figure 3 Startup with no load (Ch1:PVIN, Ch2: VOUT, Ch3: PG, Ch4:VCC, Ch5: Enable)  
Figure 4 Startup with 6A load (Ch1:PVIN, Ch2: VOUT, Ch3: PG, Ch4:VCC, Ch5: Enable)  
Page 6  
Rev 1.2, Jun 10, 2020  
Patent Protected: US 9,729,059 B1; US 10,193,442 B2  
Copyright© 2018–20 TDK Corporation. All rights reserved.  
All registered trademarks and trademarks are the property of their respective owners.  
Data and specifications subject to change without notice.  
 
EV1406-1800-A  
Figure 5 Shutdown with Enable de-assertion at 6A load (Ch1:PVIN, Ch2: VOUT, Ch3: PG, Ch4:VCC, Ch5: Enable)  
Figure 6 Soft turn off at 6A (Ch1:PVIN, Ch2: VOUT, Ch3: PG, Ch4:VCC, Ch5: Enable)  
Page 7  
Rev 1.2, Jun 10, 2020  
Patent Protected: US 9,729,059 B1; US 10,193,442 B2  
Copyright© 2018–20 TDK Corporation. All rights reserved.  
All registered trademarks and trademarks are the property of their respective owners.  
Data and specifications subject to change without notice.  
EV1406-1800-A  
Figure 7 Startup into pre-bias  
(Ch1:PVIN, Ch2: VOUT, Ch3: PG, Ch4:VCC, Ch5: Enable)  
Figure 8 Over-current protection and auto-recover to 6A  
(Ch1:PVIN, Ch2: VOUT, Ch3: PG, Ch4:VCC, Ch5: Enable)  
Page 8  
Rev 1.2, Jun 10, 2020  
Patent Protected: US 9,729,059 B1; US 10,193,442 B2  
Copyright© 2018–20 TDK Corporation. All rights reserved.  
All registered trademarks and trademarks are the property of their respective owners.  
Data and specifications subject to change without notice.  
EV1406-1800-A  
Figure 9 Sw at 0A (Ch2: Sw, Ch6: IO)  
Figure 10 Sw at 0A (Ch2: Sw, Ch6: IO)  
Page 9  
Rev 1.2, Jun 10, 2020  
Patent Protected: US 9,729,059 B1; US 10,193,442 B2  
Copyright© 2018–20 TDK Corporation. All rights reserved.  
All registered trademarks and trademarks are the property of their respective owners.  
Data and specifications subject to change without notice.  
EV1406-1800-A  
Figure 11 VOUT ripple at 0A (Ch7:VOUT, Ch8:IO), Peak-Peak VOUT ripple = 12.5mV  
Figure 12 VOUT ripple at 6A (Ch7:VOUT, Ch8:IO), Peak-Peak VOUT ripple = 12.4mV  
Page 10  
Rev 1.2, Jun 10, 2020  
Patent Protected: US 9,729,059 B1; US 10,193,442 B2  
Copyright© 2018–20 TDK Corporation. All rights reserved.  
All registered trademarks and trademarks are the property of their respective owners.  
Data and specifications subject to change without notice.  
EV1406-1800-A  
Figure 13 Transient response 0A to 6A (Ch6:IO, Ch7: VOUT), peak-peak deviation = 30mV  
Figure 14 Transient response 3A to 6A (Ch6:IO, Ch7: VOUT), peak-peak deviation = 21mV  
Page 11  
Rev 1.2, Jun 10, 2020  
Patent Protected: US 9,729,059 B1; US 10,193,442 B2  
Copyright© 2018–20 TDK Corporation. All rights reserved.  
All registered trademarks and trademarks are the property of their respective owners.  
Data and specifications subject to change without notice.  
EV1406-1800-A  
Figure 15 Efficiency  
Figure 16 Power loss  
Page 12  
Rev 1.2, Jun 10, 2020  
Patent Protected: US 9,729,059 B1; US 10,193,442 B2  
Copyright© 2018–20 TDK Corporation. All rights reserved.  
All registered trademarks and trademarks are the property of their respective owners.  
Data and specifications subject to change without notice.  
EV1406-1800-A  
Figure 17 Load regulation (IO = 0–6A)  
Page 13  
Rev 1.2, Jun 10, 2020  
Patent Protected: US 9,729,059 B1; US 10,193,442 B2  
Copyright© 2018–20 TDK Corporation. All rights reserved.  
All registered trademarks and trademarks are the property of their respective owners.  
Data and specifications subject to change without notice.  
 
EV1406-1800-A  
Figure 18 Thermal image – maximum temperature reached by FS1406 = 69°C  
Page 14  
Rev 1.2, Jun 10, 2020  
Patent Protected: US 9,729,059 B1; US 10,193,442 B2  
Copyright© 2018–20 TDK Corporation. All rights reserved.  
All registered trademarks and trademarks are the property of their respective owners.  
Data and specifications subject to change without notice.  
 
EV1406-1800-A  
Disclaimer  
IMPORTANT NOTICE AND DISCLAIMER  
TDK PROVIDES THIS POWER DESIGN USER GUIDE (“Resources”) “AS IS” AND WITH ALL  
FAULTS, AND DISCLAIMS. ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT  
LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR  
PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS.  
These Resources are intended for skilled developers designing with TDK products. You are solely responsible for (1) selecting the appropriate TDK  
products for your application, (2) designing, validating and testing your application, (3) ensuring your application meets applicable standards, and any  
other safety, security, or other requirements, and (4) ensuring your application complies with all applicable laws and regulations. These Resources are  
subject to change without notice and TDK assumes no responsibility for any notices or lack thereof. TDK grants you permission to use these Resources  
solely for development of an application that uses the TDK products described in the Resource.  
This permission may be revoked at any time by TDK or any of its affiliates. Your use of these Resources shall be in compliance with all applicable laws  
and regulations including applicable export/import controls. Reproduction and display of these Resources is prohibited. No license is granted to any  
other TDK intellectual property right or to any third party intellectual property right. TDK disclaims responsibility for, and you agree to fully indemnify  
TDK, its affiliates and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these Resources.  
REMINDERS FOR USING THESE PRODUCTS  
Before using these products, be sure to request the delivery specifications.  
SAFETY REMINDERS  
Please pay sufficient attention to the warnings for safe designing when using these products.  
The products listed on this specification sheet are intended for use in general electric equipment (AV equipment, telecommunication equipment,  
REMINDER  
home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots)  
under a normal condition and use condition.  
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a  
more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to sociality, person or property.  
Please understand that we are not responsible for any damage or liability caused by use of the products in any of the applications below or for any  
other use exceeding the range or conditions set forth in this specification sheet.  
1.  
2.  
3.  
Aerospace/Aviation equipment  
Transportation equipment (cars, electric trains, ships, etc.)  
Medical equipment  
4.  
5.  
6.  
Power-generation control equipment  
Atomic energy related equipment  
Seabed equipment  
7.  
8.  
9.  
Transportation control equipment  
Public Information-processing equipment  
Military equipment  
10.  
11.  
12.  
13.  
Electric heating apparatus, burning equipment  
Disaster prevention/crime prevention equipment  
Safety equipment  
Other applications that are not considered general-purpose applications  
When using this product in general-purpose application, you are kindly requested to take into consideration securing protection circuit/ equipment or  
providing backup circuits, etc., to ensure higher safety.  
This product is subject to a license from Power One, Inc. related to digital power technology patents owned by Power One,  
Inc. Power One, Inc. technology is protected by patents including:  
AU  
CN  
3287379M 3287437AA 3290643AA 3291357AA  
10371856C 10452610C 10458656C 10459360C 10465848C 1069332A 11124619A 11346682A 1685299A 1685459A  
1685582A 1685583A 1698023A 1802619A  
EP  
1561156A1 1561268A2 1576710A1 1576711A1 1604254A4 1604264A4 1714369A2 1745536A4 1769382A4 1899789A2  
1984801A2  
US  
20040246754 2004090219A1 2004093533A1 2004123164A1 2004123167A1 2004178780A1 2004179382A1  
20050200344 20050223252 2005209373A1 20060061214 2006015619A1 20060174145 20070226526 20070234095  
20070240000 20080052551 20080072080 20080186006 6741099 6788036 6936999 6949916 7000125 7049798  
7069021 7080265 7249267 7266709 7315156 7372682 7373527 7394445 7456617 7459892 7493504 7526660  
04044718A1 04045042A3 04045042C1 04062061A1 04062062A1 04070780A3 04084390A3 04084391A3 05079227A3  
05081771A3 06019569A3 2007001584A3 2007094935A3  
WO  
Page 15  
Rev 1.2, Jun 10, 2020  
Patent Protected: US 9,729,059 B1; US 10,193,442 B2  
Copyright© 2018–20 TDK Corporation. All rights reserved.  
All registered trademarks and trademarks are the property of their respective owners.  
Data and specifications subject to change without notice.  

相关型号:

EV1409EAN

VOLTAGE-CONTROLLED SAW OSCILLATOR (VCSO)
EPSON

EV1409SAN

VOLTAGE-CONTROLLED SAW OSCILLATOR (VCSO)
EPSON

EV1412-0600-A

µPOL™嵌入式DC-DC转换器
TDK

EV14D1100K

Metal Oxide Varistors
WPI

EV14D11K

Metal Oxide Varistors
WPI

EV14D11K-J

Metal Oxide Varistors
WPI

EV14D120K

Metal Oxide Varistors
WPI

EV14D120K-H

Metal Oxide Varistors
WPI

EV14D120K-J

Metal Oxide Varistors
WPI

EV14D130K

Metal Oxide Varistors
WPI

EV14D130K-H

Metal Oxide Varistors
WPI

EV14D130K-J

Metal Oxide Varistors
WPI