ICG-1020P [TDK]
陀螺仪;
| 型号： | ICG-1020P |
| 厂家： | 
TDK ELECTRONICS |
| 描述： | 陀螺仪 |
| 文件： | 总1页 (文件大小：311K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
ICG-1020P and ICG-1021P
Thinnest and Highest Performance Dual-Axis OIS Optimized MEMS Gyroscope
GENERAL DESCRIPTION
APPLICATIONS
The ICG-1020P and ICG-1021P dual-axis MEMS angular rate
sensors are designed for optical image stabilization (OIS)
applications in smartphone camera modules and other
mobile devices.
Smart Phone Camera Modules
Digital Still Camera and Video Cameras
High Resolution / Low Noise Applications
The ICG-1020P provides small 2.3x2.3mm2 package with
0.65mm thickness where the ICG-1021P offers the same
performance in an extremely thin package with 0.5mm
package height.
FEATURES
ICG-1020P: Small 2.3 x 2.3 x 0.65 mm LGA Package
ICG-1021P: Thin 2.3 x 2.3 x 0.5 mm LGA Package
Very Low 3.5 mdps/√Hz Rate Noise
Extremely tight sensitivity eliminates OIS dynamic
calibration
Both ICG-1020P and ICG-1021P support an innovative
approach of allowing the ODR to vary slightly to provide
lower RMS noise than the already benchmark level of ICG-
1020S and ICG-1021S devices.
Fully programmable Low-pass filters to 1500 Hz
Drop-in replacement for IDG-2030U
Resistant to 36kHz to 40kHz ultrasonic wash
frequencies
The high-resolution gyros support a programmable full-scale
range of ±46.5 dps to ±374 degrees/sec, fast sample rate at
up to 32 KHz, low phase delay including a fast 20 MHz SPI
interface, very low rate noise at 3.5 mdps/√Hz, and extremely
low power consumption at 2.5 mA. Precise sensitivity control
allows a calibration-less strategy for gyroscope to save
production cost and time by eliminating the shake table.
Fully programmable High-pass filters at 0.05 to 10Hz
to remove offset drift due to temp & PCB warp
Sense Peak Frequency tolerance and Fdrive values
are stored in OTP
Independent ODR v. LPF selection for the most
optimized performance
Narrow FSR Range from ±46.5 dps to ±374 dps
High Resolution at up to 700 LSB/(º/s)
Fast Start up Time; Sleep to Ready at 25 ms
Fast 20 MHz (3 & 4 wire) SPI Interface
Temperature sensor for offset temp compensation
Wide 1.71V to 3.6V Supply Voltage Range
Low 5mW Active Power & 6μA Sleep Mode
Self-test allows quick gyro functionally check
High 10,000g Shock Survivability
ORDERING INFORMATION
AXES
X,Y
X,Y
PART
ICG-1020P+
ICG-1021P+
TEMP RANGE
-40°C to +85°C
-40°C to +85°C
PACKAGE
12-Pin LGA
12-Pin LGA
†Denotes RoHS and Green-Compliant Package
BLOCK DIAGRAM
TYPICAL OPERATING CIRCUIT (TOP VIEW)
NC
12
NC
10
VDD
11
INT
CSN
1
2
3
9
8
7
C2
0.1µF, ±10%
10V
RESV-G
REGOUT
RSV-G
C1
0.1µF, ±10%
5V
4
5
6
SDO
SDI/SDIO SCLK
InvenSense Inc.
1745 Technology Drive, San Jose, CA 95110 U.S.A
This document contains information on a pre-production
product. InvenSense Inc. reserves the right to
changespecifications and information herein without
notice.
Document Number: PB-ICG-1020/1P-00
Revision: 1.0
Revision Date: 11/30/2015
+1(408) 988–7339
www.invensense.com
相关型号：
©2020 ICPDF网 联系我们和版权申明