MHQ0603P_技术文档

I

N

D

U

C

T

O

R

S

September 2013

Inductors for High Frequency Circuits

Multilayer Ceramic

MHQ-Pseries

MHQ0603P

MHQ1005P

0603 [0201 inch]*

1005 [0402 inch]

* Dimensions Code JIS[EIA]

(2/17)

I

N

D

U

C

T

O

R

S

REMINDERS FOR USING THESE PRODUCTS

Before using these products, be sure to request the delivery specifications.

SAFETY REMINDERS

Please pay sufficient attention to the warnings for safe designing when using these products.

REMINDERS

The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH

or less).

If the storage period elapses, the soldering of the terminal electrodes may deteriorate.

Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).

Before soldering, be sure to preheat components.

The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature

does not exceed 150°C.

Soldering corrections after mounting should be within the range of the conditions determined in the specifications.

If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.

When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to

the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.

Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal

design.

Carefully lay out the coil for the circuit board design of the non-magnetic shield type.

A malfunction may occur due to magnetic interference.

Use a wrist band to discharge static electricity in your body through the grounding wire.

Do not expose the products to magnets or magnetic fields.

Do not use for a purpose outside of the contents regulated in the delivery specifications.

The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications

equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement

equipment, industrial robots) under a normal operation and use condition.

The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or

quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to

society, person or property.

If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions

set forth in the each catalog, please contact us.

(1) Aerospace/Aviation equipment

(2) Transportation equipment (cars, electric trains, ships, etc.)

(3) Medical equipment

(8) Public information-processing equipment

(9) Military equipment

(10) Electric heating apparatus, burning equipment

(11) Disaster prevention/crime prevention equipment

(12) Safety equipment

(4) Power-generation control equipment

(5) Atomic energy-related equipment

(6) Seabed equipment

(13) Other applications that are not considered general-purpose

applications

(7) Transportation control equipment

When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing

protection circuit/device or providing backup circuits in your equipment.

001-01 / 20130929 / inductor_high-frequency_mhq_en.fm

(3/17)

I

N

D

U

C

T

O

R

S

Product compatible with RoHS directive

Halogen-free

Inductors for High Frequency Circuits

Multilayer Ceramic

Compatible with lead-free solders

AEC-Q200

Overview of the MHQ-P Series

FEATURES

Unique ceramic material and configuration allows for the realization of high Q characteristics that are equivalent to that of air core wound

inductors.

Multilayer method allows for a lineup with fine increments of inductance.

APPLICATION

Smart phones, tablet terminals, high frequency modules (PAs, VCOs, FEMs , etc.), Bluetooth, W-LAN, UWB, tuners, automotive equipment

and other high frequency circuits for the mobile communication industry

PART NUMBER CONSTRUCTION

MHQ

0603

P

0N6

S

T

□□□

L×W×H Dimensions

(mm)

Inductance

(nH)

Inductance

tolerance

Series name

Characteristics

Packaging style

Internal code

0603 0.65×0.35×0.35

P

0N6

1N1

11N

0.6

1.1

11

B

0.1nH

0.2nH

0.3nH

2%

3%

5%

T

Taping

1005

1.0×0.5×0.5

C

S

G

H

J

OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT

Temperature range

Package quantity

Individual weight

Operating

temperature

Storage

temperature

Type

ꢀ

(pieces/reel)

15000

（°C）

（mg）

MHQ0603P

MHQ1005P

–55 to +125

1

10000

ꢀꢁꢁ

The Storage temperature range is for after the circuit board is mounted.

RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://www.tdk.co.jp/rohs/

Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.

• All specifications are subject to change without notice.

001-01 / 20130929 / inductor_high-frequency_mhq_en.fm

(4/17)

I

N

D

U

C

T

O

R

S

Overview of the MHQ-P Series

RECOMMENDED REFLOW PROFILE

Preheating

Soldering

Natural

cooling

Peak

T4

T3

T2

t3

t2

T1

t1

t: Time

Preheating

Temp.

T1

Soldering

Temp.

T3

Peak

Temp.

T4

Time

t1

60 to 120s

Time

t2

30 to 60s

Time

t3

10s max.

T2

180°C

150°C

230°C

250 to 260°C

• All specifications are subject to change without notice.

001-01 / 20130929 / inductor_high-frequency_mhq_en.fm

(5/17)

I

N

D

U

C

T

O

R

S

MHQ-Pseries

MHQ0603P Type

SHAPE & DIMENSIONS

0.09 0.04

0.65 0.05

Dimensions in mm

0.15 0.05

RECOMMENDED LAND PATTERN

0.25

0.30

0.25

Dimensions in mm

• All specifications are subject to change without notice.

001-01 / 20130929 / inductor_high-frequency_mhq_en.fm

(6/17)

I

N

D

U

C

T

O

R

S

MHQ-Pseriesꢀ

MHQ0603P Type

ELECTRICAL CHARACTERISTICS

CHARACTERISTICS SPECIFICATION TABLE

Self-resonant

frequency

(GHz)

DC resistance

(ꢂ)

L measuring

frequency

(MHz)

Q measuring

frequency

(MHz)

Rated current

(mA)

max.

L

Q

min.

Part No.*

(nH)

0.6

0.7

0.8

0.9

1.0

1.1

1.2

1.3

1.4

1.5

1.6

1.7

1.8

1.9

2.0

2.1

2.2

2.3

2.4

2.5

2.6

2.7

2.8

2.9

3.0

3.1

3.2

3.3

3.4

3.5

3.6

3.7

3.8

3.9

4.0

4.1

4.2

4.3

4.7

5.1

5.6

6.2

Tolerance

0.1, 0.2nH

min.

10.0

8.0

typ.

20.0

18.8

19.3

20.0

18.6

19.5

17.5

16.7

15.8

16.1

13.8

12.7

13.2

12.5

11.7

11.1

10.5

10.6

10.8

10.3

10.5

9.5

max.

0.07

0.08

0.10

0.12

0.15

0.25

0.30

0.20

0.25

0.30

0.35

0.40

0.70

typ.

0.02

0.03

0.04

0.06

0.05

0.06

0.07

0.08

0.09

0.08

0.17

0.16

0.18

0.19

0.13

0.15

0.14

0.17

0.16

0.17

0.19

0.23

0.26

0.22

0.23

0.25

0.24

0.29

0.52

500

1000

800

700

500

450

550

500

450

400

350

300

－

16

MHQ0603P0N6△T□□□

MHQ0603P0N7△T□□□

MHQ0603P0N8△T□□□

MHQ0603P0N9△T□□□

MHQ0603P1N0△T□□□

MHQ0603P1N1△T□□□

MHQ0603P1N2△T□□□

MHQ0603P1N3△T□□□

MHQ0603P1N4△T□□□

MHQ0603P1N5△T□□□

MHQ0603P1N6△T□□□

MHQ0603P1N7△T□□□

MHQ0603P1N8△T□□□

MHQ0603P1N9△T□□□

MHQ0603P2N0△T□□□

MHQ0603P2N1△T□□□

MHQ0603P2N2△T□□□

MHQ0603P2N3△T□□□

MHQ0603P2N4△T□□□

MHQ0603P2N5△T□□□

MHQ0603P2N6△T□□□

MHQ0603P2N7△T□□□

MHQ0603P2N8△T□□□

MHQ0603P2N9△T□□□

MHQ0603P3N0△T□□□

MHQ0603P3N1△T□□□

MHQ0603P3N2△T□□□

MHQ0603P3N3△T□□□

MHQ0603P3N4△T□□□

MHQ0603P3N5△T□□□

MHQ0603P3N6△T□□□

MHQ0603P3N7△T□□□

MHQ0603P3N8△T□□□

MHQ0603P3N9△T□□□

MHQ0603P4N0△T□□□

MHQ0603P4N1△T□□□

MHQ0603P4N2△T□□□

MHQ0603P4N3△T□□□

MHQ0603P4N7△T□□□

MHQ0603P5N1△T□□□

MHQ0603P5N6△T□□□

MHQ0603P6N2△T□□□

0.1, 0.2, 0.3nH 500

0.2, 0.3nH, 3% 500

8.0

7.0

9.6

6.5

9.3

6.5

9.5

6.5

9.1

6.5

9.1

6.5

9.1

6.5

9.2

6.0

8.5

6.0

8.3

6.0

8.2

6.0

8.2

5.5

7.9

5.5

7.8

5.0

7.1

0.3nH, 3%

500

4.0

6.7

^ꢀꢁThe " △ " of the Part Number contains the inductance tolerance code, B（ 0.1nH）, C（ 0.2nH）, S（ 0.3nH）, G（ 2%）, H（ 3%）or J（ 5%）.

^ꢀꢁThe " □□□ " of the Part Number contains the internal code.

^・Short bar residual inductance =0.556nH

○ Measurement equipment

Measurement item

Product No.

4991A+16197A

8720C

Manufacturer

L, Q

Agilent Technologies

Yokogawa

Self-resonant frequency

DC resistance

Type-7561

＊ Equivalent measurement equipment may be used.

• All specifications are subject to change without notice.

001-01 / 20130929 / inductor_high-frequency_mhq_en.fm

(7/17)

I

N

D

U

C

T

O

R

S

MHQ-Pseriesꢀ

MHQ0603P Type

ELECTRICAL CHARACTERISTICS

CHARACTERISTICS SPECIFICATION TABLE

Self-resonant

frequency

(GHz)

DC resistance

(ꢂ)

L measuring

frequency

(MHz)

Q measuring

frequency

(MHz)

Rated current

(mA)

max.

L

Q

min.

Part No.*

(nH)

6.8

7.5

8.2

9.1

10

11

12

13

15

16

18

20

22

24

27

30

33

36

39

Tolerance

3%, 5%

min.

4.0

3.8

3.5

3.2

2.8

2.5

2.4

2.2

2.1

2.0

1.9

1.8

1.7

1.6

typ.

6.8

5.7

5.4

5.5

5.2

4.6

4.5

4.2

4.0

3.7

3.5

3.3

3.1

2.9

2.7

2.5

2.4

2.3

max.

0.70

0.50

0.90

1.20

1.30

1.40

1.50

1.70

2.00

2.20

2.70

2.80

3.00

typ.

0.53

0.37

0.64

0.62

0.86

0.89

0.77

1.01

1.05

1.21

1.38

1.40

1.55

1.98

2.06

2.08

2.24

500

300

16

14

500

300

250

240

180

160

MHQ0603P6N8△T□□□

MHQ0603P7N5△T□□□

MHQ0603P8N2△T□□□

MHQ0603P9N1△T□□□

MHQ0603P10N△T□□□

MHQ0603P11N△T□□□

MHQ0603P12N△T□□□

MHQ0603P13N△T□□□

MHQ0603P15N△T□□□

MHQ0603P16N△T□□□

MHQ0603P18N△T□□□

MHQ0603P20N△T□□□

MHQ0603P22N△T□□□

MHQ0603P24N△T□□□

MHQ0603P27N△T□□□

MHQ0603P30N△T□□□

MHQ0603P33N△T□□□

MHQ0603P36N△T□□□

MHQ0603P39N△T□□□

^ꢀꢁThe " △ " of the Part Number contains the inductance tolerance code, B（ 0.1nH）, C（ 0.2nH）, S（ 0.3nH）, G（ 2%）, H（ 3%）or J（ 5%）.

^ꢀꢁThe " □□□ " of the Part Number contains the internal code.

^・Short bar residual inductance =0.556nH

○ Measurement equipment

Measurement item

Product No.

4991A+16197A

8720C

Manufacturer

L, Q

Agilent Technologies

Yokogawa

Self-resonant frequency

DC resistance

Type-7561

＊ Equivalent measurement equipment may be used.

• All specifications are subject to change without notice.

001-01 / 20130929 / inductor_high-frequency_mhq_en.fm

(8/17)

I

N

D

U

C

T

O

R

S

MHQ-Pseriesꢀ

MHQ0603P Type

ELECTRICAL CHARACTERISTICS

L, Q FREQUENCY CHARACTERISTICS TABLE

L(nH)typ.

Q typ.

500MHz

29min.

29

28

30

29

28

27

29

28

31

25

26

24

23

24

27

25

27

25

26

24

23

Part No.*

500MHz

0.6

0.7

0.8

0.9

1.0

1.1

1.2

1.3

1.4

1.5

1.6

1.7

1.8

1.9

2.0

2.1

2.2

2.3

2.4

2.5

2.6

2.7

2.8

2.9

3.0

3.1

3.2

3.3

3.4

3.5

3.6

3.7

3.8

3.9

4.0

4.1

4.2

4.3

4.7

5.1

5.6

6.2

800MHz

0.6

0.7

0.8

0.9

1.0

1.1

1.2

1.3

1.4

1.5

1.6

1.7

1.8

1.9

2.0

2.1

2.2

2.3

2.4

2.5

2.6

2.7

2.8

2.9

3.0

3.1

3.2

3.3

3.4

3.5

3.6

3.7

3.8

3.9

4.0

4.1

4.2

4.3

4.7

5.1

5.6

6.2

1.8GHz

0.6

0.7

0.8

0.9

1.0

1.1

1.2

1.3

1.4

1.5

1.6

1.7

1.8

1.9

2.0

2.1

2.2

2.3

2.4

2.5

2.6

2.7

2.8

2.9

3.0

3.2

3.3

3.4

3.5

3.6

3.7

3.8

3.9

4.0

4.1

4.2

4.3

4.4

4.9

5.3

5.9

6.6

2.0GHz

0.6

0.7

0.8

0.9

1.0

1.1

1.2

1.3

1.4

1.5

1.6

1.7

1.8

1.9

2.0

2.1

2.2

2.3

2.4

2.6

2.7

2.8

2.9

3.0

3.1

3.2

3.3

3.4

3.5

3.6

3.7

3.8

3.9

4.1

4.2

4.3

4.4

4.5

4.9

5.4

6.0

6.7

2.4GHz

0.6

0.7

0.8

0.9

1.0

1.1

1.2

1.3

1.4

1.5

1.6

1.7

1.8

1.9

2.0

2.2

2.3

2.4

2.5

2.6

2.7

2.8

2.9

3.0

3.1

3.2

3.4

3.5

3.6

3.7

3.8

3.9

4.0

4.2

4.3

4.4

4.5

4.6

5.1

5.5

6.2

7.0

800MHz

38min.

38

37

39

38

35

37

40

41

32

34

35

31

30

32

35

32

35

33

34

32

30

1.8GHz

58min.

58

56

62

59

57

55

58

57

61

62

51

54

48

46

49

53

48

53

50

51

49

47

2.0GHz

60min.

60

65

62

60

58

62

61

64

53

56

57

55

51

48

51

55

50

55

52

51

49

2.4GHz

66min.

66

71

69

66

64

68

71

59

62

63

62

56

52

57

61

54

61

57

58

56

54

MHQ0603P0N6△T□□□

MHQ0603P0N7△T□□□

MHQ0603P0N8△T□□□

MHQ0603P0N9△T□□□

MHQ0603P1N0△T□□□

MHQ0603P1N1△T□□□

MHQ0603P1N2△T□□□

MHQ0603P1N3△T□□□

MHQ0603P1N4△T□□□

MHQ0603P1N5△T□□□

MHQ0603P1N6△T□□□

MHQ0603P1N7△T□□□

MHQ0603P1N8△T□□□

MHQ0603P1N9△T□□□

MHQ0603P2N0△T□□□

MHQ0603P2N1△T□□□

MHQ0603P2N2△T□□□

MHQ0603P2N3△T□□□

MHQ0603P2N4△T□□□

MHQ0603P2N5△T□□□

MHQ0603P2N6△T□□□

MHQ0603P2N7△T□□□

MHQ0603P2N8△T□□□

MHQ0603P2N9△T□□□

MHQ0603P3N0△T□□□

MHQ0603P3N1△T□□□

MHQ0603P3N2△T□□□

MHQ0603P3N3△T□□□

MHQ0603P3N4△T□□□

MHQ0603P3N5△T□□□

MHQ0603P3N6△T□□□

MHQ0603P3N7△T□□□

MHQ0603P3N8△T□□□

MHQ0603P3N9△T□□□

MHQ0603P4N0△T□□□

MHQ0603P4N1△T□□□

MHQ0603P4N2△T□□□

MHQ0603P4N3△T□□□

MHQ0603P4N7△T□□□

MHQ0603P5N1△T□□□

MHQ0603P5N6△T□□□

MHQ0603P6N2△T□□□

26

23

24

25

24

25

24

21

34

30

31

33

31

32

31

28

52

46

49

47

49

46

42

53

48

51

49

51

48

43

59

52

56

54

56

52

47

^ꢀꢁThe " △ " of the Part Number contains the inductance tolerance code, B（ 0.1nH）, C（ 0.2nH）, S（ 0.3nH）, G（ 2%）, H（ 3%）or J（ 5%）.

^ꢀꢁThe " □□□ " of the Part Number contains the internal code.

○ Measurement equipment

Product No.

Manufacturer

4291B+16193A

Agilent Technologies

＊ Equivalent measurement equipment may be used.

• All specifications are subject to change without notice.

001-01 / 20130929 / inductor_high-frequency_mhq_en.fm

(9/17)

I

N

D

U

C

T

O

R

S

MHQ-Pseriesꢀ

MHQ0603P Type

ELECTRICAL CHARACTERISTICS

L, Q FREQUENCY CHARACTERISTICS TABLE

L(nH)typ.

Q typ.

500MHz

22

24

21

23

22

21

23

21

23

22

23

22

23

22

23

Part No.*

500MHz

6.8

7.5

8.2

9.1

10

800MHz

6.8

7.5

8.2

9.2

10

1.8GHz

7.2

8.1

8.9

9.9

11

2.0GHz

7.4

8.3

9.2

10.2

11

2.4GHz

7.7

8.8

9.7

10.9

12

800MHz

28

30

27

29

28

27

29

27

29

28

27

29

26

28

27

1.8GHz

43

44

39

42

41

37

41

36

37

36

33

34

29

30

2.0GHz

44

45

40

44

42

38

41

36

37

35

32

33

27

28

2.4GHz

48

42

46

43

39

41

36

35

33

27

MHQ0603P6N8△T□□□

MHQ0603P7N5△T□□□

MHQ0603P8N2△T□□□

MHQ0603P9N1△T□□□

MHQ0603P10N△T□□□

MHQ0603P11N△T□□□

MHQ0603P12N△T□□□

MHQ0603P13N△T□□□

MHQ0603P15N△T□□□

MHQ0603P16N△T□□□

MHQ0603P18N△T□□□

MHQ0603P20N△T□□□

MHQ0603P22N△T□□□

MHQ0603P24N△T□□□

MHQ0603P27N△T□□□

MHQ0603P30N△T□□□

MHQ0603P33N△T□□□

MHQ0603P36N△T□□□

MHQ0603P39N△T□□□

11

12

13

14

12

14

16

13

15

16

18

15

18

19

21

16

19

20

23

18

22

24

28

20

21

26

28

34

22

23

29

32

40

28

24

25

34

38

27

28

38

44

30

32

47

22

23

33

35

55

27

26

36

38

67

39

42

79

^ꢀꢁThe " △ " of the Part Number contains the inductance tolerance code, B（ 0.1nH）, C（ 0.2nH）, S（ 0.3nH）, G（ 2%）, H（ 3%）or J（ 5%）.

^ꢀꢁThe " □□□ " of the Part Number contains the internal code.

○ Measurement equipment

Product No.

Manufacturer

4291B+16193A

Agilent Technologies

＊ Equivalent measurement equipment may be used.

• All specifications are subject to change without notice.

001-01 / 20130929 / inductor_high-frequency_mhq_en.fm

(10/17)

I

N

D

U

C

T

O

R

S

MHQ-Pseriesꢀ

MHQ0603PType

ELECTRICAL CHARACTERISTICS

L FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE)

100

39N

27N

22N

33N

18N

15N

12N

10N

8N2

10

6N8

5N6

4N7

3N9

3N3

2N7

2N2

1N8

1N5

1N2

1N0

1

0

1

10

100

1000

10000

(

)

Frequency MHz

○ Measurement equipment

Product No.

Manufacturer

E4991+16193A

Agilent Technologies

＊ Equivalent measurement equipment may be used.

• All specifications are subject to change without notice.

001-01 / 20130929 / inductor_high-frequency_mhq_en.fm

(11/17)

I

N

D

U

C

T

O

R

S

MHQ-Pseriesꢀ

MHQ0603P Type

ELECTRICAL CHARACTERISTICS

Q FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE)

100

1N0

1N2

90

80

70

60

50

40

30

20

10

0

1N8

1N5

2N2

2N7

4N7

3N9

3N3

5N6

6N8

8N2

10N

12N

15N

18N

22N

27N

33N

39N

1

10

100

1000

10000

(

)

Frequency MHz

○ Measurement equipment

Product No.

Manufacturer

E4991+16193A

Agilent Technologies

＊ Equivalent measurement equipment may be used.

• All specifications are subject to change without notice.

001-01 / 20130929 / inductor_high-frequency_mhq_en.fm

(12/17)

I

N

D

U

C

T

O

R

S

MHQ-Pseries

MHQ1005P Type

SHAPE & DIMENSIONS

0.12 0.05

1.00 0.05

Dimensions in mm

0.22 0.08

RECOMMENDED LAND PATTERN

0.35

0.50

0.35

Dimensions in mm

• All specifications are subject to change without notice.

001-01 / 20130929 / inductor_high-frequency_mhq_en.fm

(13/17)

I

N

D

U

C

T

O

R

S

MHQ-Pseriesꢀ

MHQ1005P Type

ELECTRICAL CHARACTERISTICS

CHARACTERISTICS SPECIFICATION TABLE

Self-resonant

frequency

(GHz)

DC resistance

(ꢂ)

L measuring

frequency

(MHz)

Q measuring

frequency

(MHz)

Rated current

(mA)

max.

L

Q

min.

Part No.*

(nH)

1.0

1.1

1.2

1.3

1.5

1.6

1.8

2.0

2.2

2.4

2.7

3.0

3.3

3.6

3.9

4.3

4.7

5.1

5.6

6.2

6.8

7.5

8.2

9.1

10

Tolerance

min.

15.0

14.0

13.0

12.0

11.0

10.0

9.0

typ.

20.0

18.3

20.0

19.7

15.2

15.1

11.5

12.1

9.8

max.

0.03

0.04

0.05

0.06

0.07

0.08

0.09

0.10

0.11

0.12

0.13

0.14

0.16

0.17

0.19

0.24

0.28

typ.

0.01

0.02

0.01

0.02

0.03

0.04

0.06

0.07

0.08

0.09

0.10

0.09

0.10

0.12

0.13

0.15

0.19

0.22

0.1, 0.2, 0.3nH 100

—

23

250

1200

1000

900

800

700

600

550

500

450

400

MHQ1005P1N0△T□□□

MHQ1005P1N1△T□□□

MHQ1005P1N2△T□□□

MHQ1005P1N3△T□□□

MHQ1005P1N5△T□□□

MHQ1005P1N6△T□□□

MHQ1005P1N8△T□□□

MHQ1005P2N0△T□□□

MHQ1005P2N2△T□□□

MHQ1005P2N4△T□□□

MHQ1005P2N7△T□□□

MHQ1005P3N0△T□□□

MHQ1005P3N3△T□□□

MHQ1005P3N6△T□□□

MHQ1005P3N9△T□□□

MHQ1005P4N3△T□□□

MHQ1005P4N7△T□□□

MHQ1005P5N1△T□□□

MHQ1005P5N6△T□□□

MHQ1005P6N2△T□□□

MHQ1005P6N8△T□□□

MHQ1005P7N5△T□□□

MHQ1005P8N2△T□□□

MHQ1005P9N1△T□□□

MHQ1005P10N△T□□□

MHQ1005P12N△T□□□

MHQ1005P15N△T□□□

8.0

6.5

9.6

6.0

9.4

6.0

9.0

5.5

8.4

5.0

7.7

5.0

7.1

5.0

7.7

4.5

7.2

4.5

6.5

4.0

5.9

2%, 3%, 5%

100

4.0

5.8

4.0

5.6

3.6

4.9

3.4

4.5

3.3

4.6

12

15

2.8

3.8

2.3

3.2

^ꢀꢁThe " △ " of the Part Number contains the inductance tolerance code, B（ 0.1nH）, C（ 0.2nH）, S（ 0.3nH）, G（ 2%）, H（ 3%）or J（ 5%）.

^ꢀꢁThe " □□□ " of the Part Number contains the internal code.

^・Short bar residual inductance =0.556nH

○ Measurement equipment

Measurement item

Product No.

4291B+16193A

8720C

Manufacturer

L, Q

Agilent Technologies

Yokogawa

Self-resonant frequency

DC resistance

Type-7561

＊ Equivalent measurement equipment may be used.

• All specifications are subject to change without notice.

001-01 / 20130929 / inductor_high-frequency_mhq_en.fm

(14/17)

I

N

D

U

C

T

O

R

S

MHQ-Pseriesꢀ

MHQ1005P Type

ELECTRICAL CHARACTERISTICS

L, Q FREQUENCY CHARACTERISTICS TABLE

L(nH)typ.

Q typ.

500MHz

56min.

56

60

52

54

47

45

47

41

40

41

38

41

39

45

42

38

42

38

39

Part No.*

500MHz

1.0

1.1

1.2

1.3

1.5

1.6

1.8

2.0

2.2

2.3

2.6

2.9

3.2

3.5

3.8

4.2

4.6

5.0

5.5

6.1

6.7

7.3

8.0

8.9

9.8

12

800MHz

1.0

1.1

1.2

1.3

1.5

1.6

1.8

2.0

2.1

2.3

2.6

2.9

3.2

3.5

3.8

4.2

4.6

5.0

5.5

6.1

6.7

7.3

8.1

9.0

9.9

12

1.8GHz

1.0

1.1

1.2

1.3

1.5

1.6

1.8

2.0

2.2

2.4

2.7

3.0

3.3

3.6

3.9

4.4

4.7

5.2

5.7

6.5

7.2

7.9

8.9

9.9

11.1

14

2.0GHz

1.0

1.1

1.2

1.3

1.5

1.6

1.8

2.0

2.2

2.4

2.7

3.0

3.3

3.6

4.0

4.5

4.8

5.3

5.8

6.7

7.4

8.1

9.2

10.3

11.6

14

2.4GHz

1.0

1.1

1.2

1.3

1.5

1.6

1.8

2.0

2.2

2.4

2.7

3.1

3.4

3.7

4.1

4.6

4.9

5.4

6.1

7.0

7.8

8.5

9.8

11.2

12.6

16

800MHz

76min.

76

78

72

70

62

59

57

59

55

53

54

50

52

51

56

53

49

53

49

51

1.8GHz

126min.

126

136

123

108

104

98

87

92

91

87

86

82

79

81

84

77

76

77

73

74

67

2.0GHz

130min.

130

144

129

113

110

102

91

97

95

91

89

85

83

84

2.4GHz

160min.

160

174

152

132

129

120

108

116

112

107

105

102

98

97

95

99

91

87

88

79

77

MHQ1005P1N0△T□□□

MHQ1005P1N1△T□□□

MHQ1005P1N2△T□□□

MHQ1005P1N3△T□□□

MHQ1005P1N5△T□□□

MHQ1005P1N6△T□□□

MHQ1005P1N8△T□□□

MHQ1005P2N0△T□□□

MHQ1005P2N2△T□□□

MHQ1005P2N4△T□□□

MHQ1005P2N7△T□□□

MHQ1005P3N0△T□□□

MHQ1005P3N3△T□□□

MHQ1005P3N6△T□□□

MHQ1005P3N9△T□□□

MHQ1005P4N3△T□□□

MHQ1005P4N7△T□□□

MHQ1005P5N1△T□□□

MHQ1005P5N6△T□□□

MHQ1005P6N2△T□□□

MHQ1005P6N8△T□□□

MHQ1005P7N5△T□□□

MHQ1005P8N2△T□□□

MHQ1005P9N1△T□□□

MHQ1005P10N△T□□□

MHQ1005P12N△T□□□

MHQ1005P15N△T□□□

87

80

79

80

75

68

57

39

37

49

45

70

54

15

18

20

23

57

^ꢀꢁThe " △ " of the Part Number contains the inductance tolerance code, B（ 0.1nH）, C（ 0.2nH）, S（ 0.3nH）, G（ 2%）, H（ 3%）or J（ 5%）.

^ꢀꢁThe " □□□ " of the Part Number contains the internal code.

○ Measurement equipment

Product No.

Manufacturer

4291B+16193A

Agilent Technologies

＊ Equivalent measurement equipment may be used.

• All specifications are subject to change without notice.

001-01 / 20130929 / inductor_high-frequency_mhq_en.fm

(15/17)

I

N

D

U

C

T

O

R

S

MHQ-Pseriesꢀ

MHQ1005PType

ELECTRICAL CHARACTERISTICS

L FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE)

1000

100

10

1

15N

12N

10N

8N2

6N8

5N6

4N7

3N9

3N3

2N7

2N2

1N8

1N5

1N2

1N0

0

10

100

1000

10000

(

)

Frequency MHz

○ Measurement equipment

Product No.

E4991+16193A

Manufacturer

Agilent Technologies

＊ Equivalent measurement equipment may be used.

• All specifications are subject to change without notice.

001-01 / 20130929 / inductor_high-frequency_mhq_en.fm

(16/17)

I

N

D

U

C

T

O

R

S

MHQ-Pseriesꢀ

MHQ1005P Type

ELECTRICAL CHARACTERISTICS

Q FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE)

200

1N5

1N8

1N2

1N0

180

160

140

120

100

80

2N2

2N7

3N3

3N9

4N7

5N6

6N8

8N2

10N

12N

60

40

15N

20

0

10

100

1000

10000

(

)

Frequency MHz

○ Measurement equipment

Product No.

E4991+16193A

Manufacturer

Agilent Technologies

＊ Equivalent measurement equipment may be used.

• All specifications are subject to change without notice.

001-01 / 20130929 / inductor_high-frequency_mhq_en.fm

(17/17)

I

N

D

U

C

T

O

R

S

MHQ-Pseries

Packaging Style

REEL DIMENSIONS

1.0

+2.0

2.0 0.5

ø13 0.2

ø21 0.8

8.4

–0.0

14.4max.

ø180 2.0

Dimensions in mm

TAPE DIMENSIONS

Type

A

B

K

MHQ0603P

MHQ1005P

0.74 0.05 0.44 0.05 0.60 max.

1.15 0.10 0.75 0.10 0.8 max.

+0.1

1.5

Sprocket hole

Cavity

–0.0

K

B

4.0 0.1

2.0 0.05

200min.

160min.

Taping

300min.

Drawing direction

• All specifications are subject to change without notice.

001-01 / 20130929 / inductor_high-frequency_mhq_en.fm


型号：	MHQ0603P
厂家：	TDK ELECTRONICS
描述：	Inductors for High Frequency Circuits 电感高频电路
文件：	总17页 (文件大小：158K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

MHQ0603P [TDK]

相关型号：

MHQ0603P0N6BT

MHQ0603P0N6BT000

MHQ0603P0N6BT000_17

MHQ0603P0N6BTD25

MHQ0603P0N6CT

MHQ0603P0N6CT000

MHQ0603P0N6CT000_17

MHQ0603P0N6CTD25

MHQ0603P0N6GT

MHQ0603P0N6HT

MHQ0603P0N6JT

MHQ0603P0N6ST