TCM0806G-650-2P-T [TDK]
Data Line Filter, 2 Function(s), 10V, 0.1A, HALOGEN FREE AND ROHS COMPLIANT, SMD, 4 PIN;
| 型号： | TCM0806G-650-2P-T |
| 厂家： | 
TDK ELECTRONICS |
| 描述： | Data Line Filter, 2 Function(s), 10V, 0.1A, HALOGEN FREE AND ROHS COMPLIANT, SMD, 4 PIN LTE |
| 文件： | 总14页 (文件大小：196K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
E M C C o m p o n e n t s
July 2013
Common Mode Filters
For high-speed differential signal line
(USB2.0, LVDS, etc.)
TCM-G series
TCM0605G
TCM0806G
TCM1608G
[0202 inch]*
[0302 inch]
[0603 inch]
* Dimensions Code JIS[EIA]
(2/14)
E M C C o m p o n e n t s
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using these products.
REMINDERS
The storage period is less than 6 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 20 to 70% RH or
less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications
equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement
equipment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or
quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to
society, person or property.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/Aviation equipment
(2) Transportation equipment (cars, electric trains, ships, etc.)
(3) Medical equipment
(8) Public information-processing equipment
(9) Military equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment
(6) Seabed equipment
(13) Other applications that are not considered general-purpose
applications
(7) Transportation control equipment
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing
protection circuit/device or providing backup circuits in your equipment.
001-01 / 20130723 / e9712_tcm_g.
(3/14)
E M C C o m p o n e n t s
Product compatible with RoHS directive
Halogen-free
Common Mode Filters
For high-speed differential signal line
Compatible with lead-free solders
(USB2.0, LVDS, etc.)
Overview of the TCM-G Series
FEATURES
Thin-film common mode filter based on the thin-film processing techniques and material technology cultivated from HDD head
manufacturing.
Has EMC suppression by achieving wide frequency range (cutoff frequency of 3GHz or higher) differential mode transmission while
ensuring common mode impedance with virtually no affect on the high-speed differential transmission line signal.
Lineup includes the compact 0605 size (0.65×0.50×0.30mm) and 1608 (1.60×0.80×0.40mm) array type, etc.
APPLICATION
Noise countermeasure for high-speed differential interfaces (USB2.0, LVDS, MIPI, etc.) for mobile devices and general consumer
products such as smart phones, tablets, digital cameras, and portable music players.
PART NUMBER CONSTRUCTION
TCM
0605
-
G
-
900
-
2P
-
T
□□□
Internal
code
L×W×T Dimensions
(mm)
Impedance
(ꢂ) at 100MHz
Product internal
Series name
Number of lines
Packaging style
code
0605 0.65×0.50×0.30
0806 0.85×0.65×0.40
1608 1.60×0.80×0.40
G
201
151
900
650
350
200
150
90
65
35
2P
4P
2 lines
4 lines
T
Taping
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT
Temperature range
Package quantity
Individual weight
Operating
temperature
ꢀ
Type
Storage temperature
（°C）
（°C）
（pieces/reel）
10,000
（mg）
0.5
1.0
TCM0605G
TCM0806G
TCM1608G
–25 to +85
–25 to +85
–25 to +85
–25 to +85
–25 to +85
–25 to +85
10,000
4,000
4.0
ꢀꢁ
The Storage temperature range is for after the circuit board is mounted.
RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://www.tdk.co.jp/rohs/
Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.
• All specifications are subject to change without notice.
001-01 / 20130723 / e9712_tcm_g.
(4/14)
E M C C o m p o n e n t s
Overview of the TCM-G Series
RECOMMENDED REFLOW PROFILE
Preheating
Soldering
Natural
cooling
Peak
T4
T3
T3
T2
t3
t2
T1
t1
t: Time
Preheating
Temp.
T1
Soldering
Temp.
T3
Peak
Temp.
T4
Time
t1
60 to 120s
Time
t2
10 to 30s
Time
t3
5s max.
T2
180°C
150°C
230°C
245°C
• All specifications are subject to change without notice.
001-01 / 20130723 / e9712_tcm_g.
(5/14)
E M C C o m p o n e n t s
TCM-G series
TCM0605G Type
SHAPE & DIMENSIONS
0.50 0.05
1
4
2
3
0.15 0.05
Dimensions in mm
RECOMMENDED LAND PATTERN
CIRCUIT DIAGRAM
0.8
1
2
4
3
• No polarity
0.3
0.2
Dimensions in mm
• All specifications are subject to change without notice.
001-01 / 20130723 / e9712_tcm_g.
(6/14)
E M C C o m p o n e n t s
TCM-G seriesꢀ
TCM0605G Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Common mode impedance
[at 100MHz]
Insulation
resistance
(Mꢂ)min.
10
DC resistance
(ꢂ)[1 line]
Rated current
(A)max.
Rated voltage
(V)max.
Part No.
(ꢂ)
65
Tolerance
20%
2.7 30%
3.0 30%
0.1
0.1
10
10
TCM0605G-650-2P-T□□□
TCM0605G-900-2P-T□□□
90
20%
10
○ Measurement equipment
Measurement item
Product No.
Manufacturer
Common mode impedance
DC resistance
Insulation resistance
4291A
4338A
4339A
Agilent Technologies
Agilent Technologies
Agilent Technologies
＊ Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20130723 / e9712_tcm_g.
(7/14)
E M C C o m p o n e n t s
TCM-G seriesꢀ
TCM0605G Type
ELECTRICAL CHARACTERISTICS
IMPEDANCE VS. FREQUENCY CHARACTERISTICS
10000
900 Common mode
1000
100
10
650 Common mode
900 Differential mode
650 Differential mode
1
1
10
100
1000
10000
(
)
Frequency MHz
○ Measurement equipment
Product No.
Manufacturer
E4991A
Agilent Technologies
＊ Equivalent measurement equipment may be used.
INSERTION LOSS VS. FREQUENCY CHARACTERISTICS
0
650 Differential mode
650 Common mode
900 Differential mode
5
900 Common mode
10
15
20
25
30
35
40
1
10
100
1000
10000
(
)
Frequency MHz
○ Measurement equipment
Product No.
Manufacturer
E5071B
Agilent Technologies
＊ Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20130723 / e9712_tcm_g.
(8/14)
E M C C o m p o n e n t s
TCM-G series
TCM0806G Type
SHAPE & DIMENSIONS
0.65 0.05
1
4
2
3
Dimensions in mm
+0.05
–0.10
0.20
RECOMMENDED LAND PATTERN
CIRCUIT DIAGRAM
0.9
1
2
4
3
• No polarity
0.3
0.3
Dimensions in mm
• All specifications are subject to change without notice.
001-01 / 20130723 / e9712_tcm_g.
(9/14)
E M C C o m p o n e n t s
TCM-G seriesꢀ
TCM0806G Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Common mode impedance
[at 100MHz]
Insulation
resistance
(Mꢂ)min.
10
10
10
10
DC resistance
(ꢂ)[1 line]
Rated current
(A)max.
Rated voltage
(V)max.
Part No.
(ꢂ)
35
Tolerance
30%
1.15 30%
2.50 30%
2.70 30%
3.50 30%
0.10
0.10
0.10
0.05
10
10
10
10
TCM0806G-350-2P-T□□□
TCM0806G-650-2P-T□□□
TCM0806G-900-2P-T□□□
TCM0806G-151-2P-T□□□
65
20%
90
20%
150
20%
○ Measurement equipment
Measurement item
Product No.
Manufacturer
Common mode impedance
DC resistance
Insulation resistance
4291A
4338A
4339A
Agilent Technologies
Agilent Technologies
Agilent Technologies
＊ Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20130723 / e9712_tcm_g.
(10/14)
E M C C o m p o n e n t s
TCM-G seriesꢀ
TCM0806G Type
ELECTRICAL CHARACTERISTICS
IMPEDANCE VS. FREQUENCY CHARACTERISTICS
10000
151 Common mode
900 Common mode
1000
650 Common mode
350 Common mode
100
10
1
900 Differential mode
650 Differential mode
350 Differential mode
151 Differential mode
1
10
100
1000
10000
(
)
Frequency MHz
○ Measurement equipment
Product No.
Manufacturer
E4991A
Agilent Technologies
＊ Equivalent measurement equipment may be used.
INSERTION LOSS VS. FREQUENCY CHARACTERISTICS
0
350 Differential mode
900 Differential mode
5
10
15
20
650 Differential mode
650 Common mode
25
30
35
40
350 Common mode
900 Common mode
151 Differential mode
151 Common mode
1
10
100
1000
10000
(
)
Frequency MHz
○ Measurement equipment
Product No.
Manufacturer
E5071B
Agilent Technologies
＊ Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20130723 / e9712_tcm_g.
(11/14)
E M C C o m p o n e n t s
TCM-G series
TCM1608G Type
SHAPE & DIMENSIONS
0.80 0.10
1
2
3
4
8
7
6
5
Dimensions in mm
0.16 0.10
RECOMMENDED LAND PATTERN
CIRCUIT DIAGRAM
1.42
0.48
1
2
3
4
8
7
6
5
• No polarity
Dimensions in mm
• All specifications are subject to change without notice.
001-01 / 20130723 / e9712_tcm_g.
(12/14)
E M C C o m p o n e n t s
TCM-G seriesꢀ
TCM1608G Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Common mode impedance
[at 100MHz]
Insulation
resistance
(Mꢂ)min.
10
10
10
10
DC resistance
(ꢂ)[1 line]
Rated current
(A)max.
Rated voltage
(V)max.
Part No.
(ꢂ)
35
Tolerance
30%
0.85 30%
1.30 30%
1.50 30%
4.00 30%
0.10
0.10
0.10
0.05
5
5
5
5
TCM1608G-350-4P-T□□□
TCM1608G-650-4P-T□□□
TCM1608G-900-4P-T□□□
TCM1608G-201-4P-T□□□
65
20%
90
20%
200
20%
○ Measurement equipment
Measurement item
Common mode impedance
DC resistance
Product No.
4291A
4338A
Manufacturer
Agilent Technologies
Agilent Technologies
Agilent Technologies
Insulation resistance
4339A
＊ Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20130723 / e9712_tcm_g.
(13/14)
E M C C o m p o n e n t s
TCM-G seriesꢀ
TCM1608G Type
ELECTRICAL CHARACTERISTICS
IMPEDANCE VS. FREQUENCY CHARACTERISTICS
10000
201 Common mode
900 Common mode
1000
650 Common mode
350 Common mode
100
10
1
201 Differential mode
900 Differential mode
650 Differential mode
350 Differential mode
1
10
100
1000
10000
(
)
Frequency MHz
○ Measurement equipment
Product No.
Manufacturer
E4991A
Agilent Technologies
＊ Equivalent measurement equipment may be used.
INSERTION LOSS VS. FREQUENCY CHARACTERISTICS
0
201 Differential mode
350 Differential mode
900 Differential mode
650 Differential mode
5
10
15
20
25
30
35
40
900 Common mode
350 Common mode
650 Common mode
201 Common mode
1
10
100
1000
10000
(
)
Frequency MHz
○ Measurement equipment
Product No.
Manufacturer
E5071B
Agilent Technologies
＊ Equivalent measurement equipment may be used.
• All specifications are subject to change without notice.
001-01 / 20130723 / e9712_tcm_g.
(14/14)
E M C C o m p o n e n t s
TCM-G series
Packaging style
REEL DIMENSIONS
2.0 0.5
1.0
9+0.3
ø13 0.2
ø21 0.8
13+1.4
+0
–3
ø180
Dimensions in mm
TAPE DIMENSIONS
TCM0605G
TCM0806G,
TCM1608G
2.0
4.0
ø1.5
K
A
P1
K
Dimensions in mm
Type
A
B
P1
K
TCM0605G
TCM0806G
TCM1608G
0.63
0.74
1.00
0.77
0.94
1.80
2.0
2.0
4.0
0.35
0.50
0.50
160min.
Taping
200min.
300min.
Drawing direction
Dimensions in mm
• All specifications are subject to change without notice.
001-01 / 20130723 / e9712_tcm_g.
相关型号：
TCM0806G-900-2P-T
Data Line Filter, 2 Function(s), 10V, 0.1A, HALOGEN FREE AND ROHS COMPLIANT, SMD, 4 PIN
TDK
TCM0806S-120-2P-T
Data Line Filter, 2 Function(s), 10V, 0.1A, HALOGEN FREE AND ROHS COMPLIANT PACKAGE-4
TDK
TCM0806S-350-2P-T
Data Line Filter, 2 Function(s), 10V, 0.1A, HALOGEN FREE AND ROHS COMPLIANT PACKAGE-4
TDK
©2020 ICPDF网 联系我们和版权申明