VLS201610ET-1R0N-CA [TDK]
General Purpose Inductor,;
| 型号： | VLS201610ET-1R0N-CA |
| 厂家： | 
TDK ELECTRONICS |
| 描述： | General Purpose Inductor, 电感器 |
| 文件： | 总9页 (文件大小：231K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
I N D U C T O R S
October 2017
Inductors for power circuits
Wound ferrite
VLS-E-CA series (For automobiles)
VLS201610E-CA type
VLS201610E-CA
Caution
The products in this catalog is not recommended
to a new design
Please refer to our Web site about replacement information.
The products in this catalog is not recommended to a new design
(2/9)
I N D U C T O R S
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using these products.
REMINDERS
The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH
or less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications
equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement
equipment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or
quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to
society, person or property.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/Aviation equipment
(2) Transportation equipment (electric trains, ships, etc.)
(3) Medical equipment
(8) Public information-processing equipment
(9) Military equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment
(6) Seabed equipment
(13) Other applications that are not considered general-purpose
applications
(7) Transportation control equipment
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing
protection circuit/device or providing backup circuits in your equipment.
20171026 / inductor_automotive_power_vls201610e-ca_en.
The products in this catalog is not recommended to a new design
(3/9)
I N D U C T O R S
Product compatible with RoHS directive
Halogen-free
Inductors for power circuits
Wound ferrite
Overview of the VLS201610E-CA type
FEATURES
Magnetic shield type wound inductor for power circuits.
Low-profile product.
High magnetic shield construction and compatible with high-density mounting.
APPLICATION
Car navigation, car stereo and car accessories only
Not available for use related to driving, curving, stopping, and the other safety.
PART NUMBER CONSTRUCTION
VLS
201610
E
T
-
R47
N
-
CA
L×W×H Dimensions
(mm)
Inductance
(µH)
Inductance
tolerance
Series name
internal code
Packaging style
Internal code
201610
2.0×1.6×1.0
T
Taping
R47
2R2
100
0.47
2.2
10
M
N
20%
30%
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT
Temperature range
Package quantity
Individual weight
Operating Storage
Type
temperature
temperature
(pieces/reel)
（°C）
（°C）
（mg）
VLS201610E-CA
Operating temperature range includes self-temperature rise.
The Storage temperature range is for after the circuit board is mounted.
–40 to +105
–40 to +105
2000
12
RoHS Directive Compliant Product: See the following for more details.https://product.tdk.com/info/en/environment/rohs/index.html
Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20171026 / inductor_automotive_power_vls201610e-ca_en.
The products in this catalog is not recommended to a new design
(4/9)
I N D U C T O R S
VLS201610E-CA type
RECOMMENDED REFLOW PROFILE
Preheating
Soldering
Natural
cooling
Peak
T4
T3
T3
T2
t3
t2
T1
t1
t: Time
Preheating
Temp.
T1
Soldering
Temp.
T3
Peak
Temp.
T4
Time
t1
60 to 120s
Time
t2
30s
Time
t3
10s
T2
180°C
150°C
230°C
260°C
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20171026 / inductor_automotive_power_vls201610e-ca_en.
The products in this catalog is not recommended to a new design
(5/9)
I N D U C T O R S
VLS201610E-CA type
SHAPE & DIMENSIONS
(
)
(
)
(
)
0.65
0.65
0.7
2.0 0.1
Dimensions in mm
RECOMMENDED LAND PATTERN
0.65
0.7
0.65
Dimensions in mm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20171026 / inductor_automotive_power_vls201610e-ca_en.
The products in this catalog is not recommended to a new design
(6/9)
I N D U C T O R S
VLS201610E-CA type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Rated current
L
Measuring
frequency
DC resistance
Part No.
Isat
Isat
Itemp
(A)typ.
1.95
1.65
1.40
1.15
0.95
0.73
0.67
0.54
0.42
(µH)
0.47
Tolerance
30%
30%
30%
30%
20%
20%
20%
20%
(MHz)
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
( )max.
0.065
0.086
0.119
0.181
0.276
0.458
0.554
0.840
1.380
( )typ.
(A)max.
1.85
1.65
1.35
1.10
0.94
0.75
0.64
0.53
0.40
(A)typ.
2.10
1.85
1.50
1.20
1.05
0.84
0.72
0.59
0.45
0.054
0.072
0.099
0.151
0.230
0.382
0.462
0.700
1.150
VLS201610ET-R47N-CA
VLS201610ET-R68N-CA
VLS201610ET-1R0N-CA
VLS201610ET-1R5N-CA
VLS201610ET-2R2M-CA
VLS201610ET-3R3M-CA
VLS201610ET-4R7M-CA
VLS201610ET-6R8M-CA
VLS201610ET-100M-CA
0.68
1.0
1.5
2.2
3.3
4.7
6.8
10
20%
Rated current: smaller value of either Isat or Itemp.
Isat: When based on the inductance change rate (30% below the nominal value)
Itemp: When based on the temperature increase (Temperature increase of 40°C by self heating)
○ Measurement equipment
Measurement item
Product No.
Manufacturer
L
4194A
VP-2941A
4285A+42841A+42842C
Keysight Technologies
Panasonic
Keysight Technologies
DC resistance
Rated current Isat
＊ Equivalent measurement equipment may be used.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20171026 / inductor_automotive_power_vls201610e-ca_en.
The products in this catalog is not recommended to a new design
(7/9)
I N D U C T O R S
VLS201610E-CA type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH
100
100M
6R8M
4R7M
3R3M
2R2M
10
1R5N
1R0N
R68N
R47N
1
0.1
0.01
0.1
1
10
100
1000
(
)
Frequency MHz
○ Measurement equipment
Product No.
Manufacturer
4294A
Keysight Technologies
＊ Equivalent measurement equipment may be used.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20171026 / inductor_automotive_power_vls201610e-ca_en.
The products in this catalog is not recommended to a new design
(8/9)
I N D U C T O R S
VLS201610E-CA type
ELECTRICAL CHARACTERISTICS
INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH
100
100M
10
6R8M
4R7M
3R3M
2R2M
1R5N
1R0N
1
R68N
R47N
0.1
0
0.5
1
1.5
2
2.5
DC current(A)
○ Measurement equipment
Product No.
Manufacturer
4285A+42841A+42842C
Keysight Technologies
＊ Equivalent measurement equipment may be used.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20171026 / inductor_automotive_power_vls201610e-ca_en.
The products in this catalog is not recommended to a new design
(9/9)
I N D U C T O R S
VLS201610E-CA type
PACKAGING STYLE
REEL DIMENSIONS
2.0 0.5
E
Type
VLS201610E-CA
A
ø180
W1
9
W2
13
N
ø60
E
0.5
* These values are typical values.
(
)
1.0
ø13.0 0.5
ø21.0 0.8
W1
W2
A
Dimensions in mm
TAPE DIMENSIONS
øD0
P2
P0
P1
K
t
Dimensions in mm
A
Type
VLS201610E-CA
A
1.8
B
2.2
øD0
E
F
P0
P1
P2
W
K
t
1.5+0.10/-0 1.75 0.1 3.5 0.05 4.0 0.1 4.0 0.1 2.00 0.05 8.0 0.2 1.1 0.25
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20171026 / inductor_automotive_power_vls201610e-ca_en.
相关型号：
VLS201610ET-1R5N
Inductors for Power Circuits Wound FerriteWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TDK
VLS201610ET-1R5N-CA
General Purpose Inductor,Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TDK
VLS201610ET-2R2M
Inductors for Power Circuits Wound FerriteWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TDK
VLS201610ET-2R2M-CA
General Purpose Inductor,Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TDK
VLS201610ET-3R3M
Inductors for Power Circuits Wound FerriteWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TDK
VLS201610ET-3R3M-CA
暂无描述Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TDK
VLS201610ET-4R7M
Inductors for Power Circuits Wound FerriteWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TDK
VLS201610ET-6R8M
Inductors for Power Circuits Wound FerriteWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TDK
VLS201610ET-6R8M-CA
General Purpose Inductor,Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TDK
VLS201610ET-R47N
Inductors for Power Circuits Wound FerriteWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TDK
VLS201610ET-R47N-CA
General Purpose Inductor,Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TDK
VLS201610ET-R68N
Inductors for Power Circuits Wound FerriteWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TDK
©2020 ICPDF网 联系我们和版权申明