CCS-32HT10-D [TELEDYNE]
Failsafe SPDT Coaxial Switch;型号: | CCS-32HT10-D |
厂家: | TELEDYNE TECHNOLOGIES INCORPORATED |
描述: | Failsafe SPDT Coaxial Switch 光电二极管 |
文件: | 总9页 (文件大小:588K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Series CCS-32/CS-32
High Power DC–12 GHz
COAX SWITCHES
Failsafe SPDT Coaxial Switch
PART NUMBER DESCRIPTION
CCS-32
CS-32
Commercial Failsafe SPDT, DC-12GHz
Elite Failsafe SPDT, DC-12GHz
Available with
USB & Ethernet
Control!
The CCS-32/CS-32 is a broadband, SPDT, electromechanical, coaxial switch designed to switch a
microwave signal from a common input to either of two outputs. The characteristic impedance is 50
Ohms. The small switches incorporate Type N or TNC connectors.
The CCS-32/CS-32 series switch is offered with a failsafe actuator. This design is compatible with the
two most common mounting hole patterns. The CCS-32/CS-32 series switch is interchangeable with a
variety of switches.
Click here
MMA SERIES
ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS
ELECTRICAL CHARACTERISTICS
Operating Temperature
Form Factor
SPDT,
Commercial Model, CCS-32
Elite Model, CS-32
–40°C to 65°C
–55°C to 85°C
break before make
Frequency Range
CCS-32
CS-32
Vibration (MIL-STD-202 Method 214,
Condition D, non-operating)
10 g’s RMS
DC–12 GHz
DC–12 GHz
Shock (MIL-STD-202 Method 213,
Condition D, non-operating)
500 g’s
Characteristic Impedance
Operate Time
50 Ohms
10 ms (max.)
10 ms (max.)
Standard Actuator Life
Actuator Life w/ Additional Features
2,000,000 cycles
1,000,000 cycles
Release Time
Actuation Voltage Available
Actuation Current, max. @ ambient
RF Power Handling
12 15 24 28 V
Connector Type
Humidity (Moisture Seal)
Weight
Type N or TNC
Available
600 500 300 250 mA
1.1 kW CW @ 1.1 GHz
6 oz. (170.1g) (max.)
TYPICAL PERFORMANCE CHARACTERISTICS: N CONNECTOR OPTION (TNC CONNECTOR, 11GHZ MAX.)
Frequency
DC–3 GHz
3–6 GHz
6–9 GHz
9–12 GHz
Insertion Loss, dB,
typical.
0.2
0.2
0.4
0.4
Isolation, dB, typical.
VSWR , typical.
70
70
70
50
1.2:1
1.2:1
1.3:1
1.3:1
For maximum limits, please see charts on page 3-5
PART NUMBERING SYSTEM
CCS-32
N
1
C
-
T **
Series
Options
Actuator Type
Connectors
Actuator Voltage
Connector
N: Type N Female
T: TNC Female
HN: High Power Type N Female
HT: High Power TNC Female
Actuator Voltage
Actuator Type
0: Standard Contacts
C: Indicator Contacts
Options
1: 28 Vdc Failsafe
2: 15 Vdc Failsafe
3: 12 Vdc Failsafe
4: 24 Vdc Failsafe
T: TTL Drivers with Diodes
D: Transient Suppression
Diodes
M: Moisture Seal
S: 9 Pin D-Sub Connector
**SEE PARTS LIST ON PAGE 8-9
For other options, contact factory.
© 2015 TELEDYNE RELAYS
(800) 284-7007 • www.teledynecoax.com
CCS-32/CS-32 Page 1
CCS-32\CS-32\112015\Q4
Series CCS-32/CS-32
High Power DC–12 GHz
Failsafe SPDT Coaxial Switch
COAX SWITCHES
SCHEMATICS AND MECHANICAL OUTLINE
Indicators
TTL
Analog
2X SOLDER TERMINALS
SOLDER WIRE MAXIMUM
TEMP 250ºC FOR NO
MORE THAN 5 SEC
H = 1.70 MAX. STD MODEL
H = 2.30 MAX. TTL MODEL
H = 1.70 MAX. STD MODEL
H = 2.30 MAX. TTL MODEL
N Type Outline
TNC Outline
1
6
“-S OPTION” 9-PIN D-SUB CONNECTOR (EXAMPLE: CCS-32N10-S)
9 PIN D-SUB PINOUT FOR FAILSAFE SPDT
TRUTH TABLE (with TTL option)
OPTIONS
Logic
Input
Indicator
(if applicable)
RF Path
Pin
No.
1
Indicators &
TTL
Basic
Indicators
TTL
1
IN
IN
A
B
+
-
+
-
to 1
On
Off
to 2
2
0
1
Off
On
C
0
0
3
4
Common
1
Common
1
C
5
6
7
8
9
Vsw
Vsw
A
B
A
B
C
C
CCS-32/CS-32 Page 2
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
© 2015 TELEDYNE COAX SWITCHES
CCS-32\CS-32\112015\Q4
Series CCS-32/CS-32
High Power DC–12 GHz
COAX SWITCHES
Failsafe SPDT Coaxial Switch
TYPICAL NARROWBAND RF INSERTION LOSS PERFORMANCE CURVES
Insertion Loss ( DC-3 GHz )
Insertion Loss ( 3-6 GHz )
0
-0.1
-0.2
-0.3
-0.4
-0.5
-0.6
-0.7
-0.8
-0.9
-1
0
-0.1
-0.2
-0.3
-0.4
-0.5
-0.6
-0.7
-0.8
-0.9
-1
0
0.5
1
1.5
2
2.5
3
3
3.5
4
4.5
5
5.5
6
Frequency ( GHz )
Frequency ( GHz )
Insertion Loss ( 6-9 GHz )
Insertion Loss ( 9-12 GHz )
0
-0.1
-0.2
-0.3
-0.4
-0.5
-0.6
-0.7
-0.8
-0.9
-1
0
-0.1
-0.2
-0.3
-0.4
-0.5
-0.6
-0.7
-0.8
-0.9
-1
6
6.5
7
7.5
8
8.5
9
9
9.5
10
10.5
11
11.5
12
Frequency ( GHz )
Frequency ( GHz )
TYPICAL
MAXIMUM TEST LIMIT
© 2015 TELEDYNE RELAYS
(800) 284-7007 • www.teledynecoax.com
CCS-32/CS-32 Page 3
CCS-32\CS-32\112015\Q4
Series CCS-32/CS-32
High Power DC–12 GHz
Failsafe SPDT Coaxial Switch
COAX SWITCHES
TYPICAL NARROWBAND RF ISOLATION PERFORMANCE CURVES
Isolation ( DC-3 GHz )
0
Isolation ( 3-6 GHz )
0
-20
-20
-40
-40
-60
-60
-80
-80
-100
-120
-140
-100
-120
-140
0
0.5
1
1.5
2
2.5
3
3
3.5
4
4.5
5
5.5
6
Frequency ( GHz )
Frequency ( GHz )
Isolation ( 6-9 GHz )
Isolation ( 9-12 GHz )
0
-20
0
-20
-40
-40
-60
-60
-80
-80
-100
-120
-140
-100
-120
-140
6
6.5
7
7.5
8
8.5
9
9
9.5
10
10.5
11
11.5
12
Frequency ( GHz )
Frequency ( GHz )
TYPICAL
MAXIMUM TEST LIMIT
CCS-32/CS-32 Page 4
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
© 2015 TELEDYNE COAX SWITCHES
CCS-32\CS-32\112015\Q4
Series CCS-32/CS-32
High Power DC–12 GHz
COAX SWITCHES
Failsafe SPDT Coaxial Switch
TYPICAL NARROWBAND RF VSWR PERFORMANCE CURVES
VSWR ( DC-3 GHz )
VSWR ( 3-6 GHz )
2
1.9
1.8
1.7
1.6
1.5
1.4
1.3
1.2
1.1
1
2
1.9
1.8
1.7
1.6
1.5
1.4
1.3
1.2
1.1
1
0
0.5
1
1.5
2
2.5
3
3
3.5
4
4.5
5
5.5
6
Frequency ( GHz )
Frequency ( GHz )
VSWR ( 6-9 GHz )
VSWR ( 9-12 GHz )
2
1.9
1.8
1.7
1.6
1.5
1.4
1.3
1.2
1.1
1
2
1.9
1.8
1.7
1.6
1.5
1.4
1.3
1.2
1.1
1
6
6.5
7
7.5
8
8.5
9
9
9.5
10
10.5
11
11.5
12
Frequency ( GHz )
Frequency ( GHz )
TYPICAL
MAXIMUM TEST LIMIT
© 2015 TELEDYNE RELAYS
(800) 284-7007 • www.teledynecoax.com
CCS-32/CS-32 Page 5
CCS-32\CS-32\112015\Q4
Series CCS-32/CS-32
High Power DC–12 GHz
Failsafe SPDT Coaxial Switch
COAX SWITCHES
TYPICAL POWER PERFORMANCE CURVE
Power Handling vs. Frequency
3000
2000
1000
800
600
400
300
200
100
80
60
40
30
20
10
.1
.2 .3 .4 .6 .8 1
2
4
6 8 10
Frequency GHz
Estimates based on the following reference conditions:
• Ambient temperature of 40°C or less
• Sea level operation
• Load VSWR of 1.20:1 maximum
• No high-power (hot) switching
Please contact Teledyne Coax Switches for derating factors when applications do not meet the foregoing reference conditions.
CCS-32/CS-32 Page 6
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
© 2015 TELEDYNE COAX SWITCHES
CCS-32\CS-32\112015\Q4
Series CCS-32/CS-32
High Power DC–12 GHz
COAX SWITCHES
Failsafe SPDT Coaxial Switch
GLOSSARY
Actuator
TTL Switch Driver Option
An actuator is the electromechanical mechanism that As a special option, switch drivers can be provided for both
transfers the RF contacts from one position to another upon failsafe and latching switches, which are compatible with
DC command.
industry-standard low-power Schottky TTL circuits.
Arc Suppression Diode
Performance Parameters vs Frequency
A diode is connected in parallel with the coil. This diode Generally speaking, the RF performance of coaxial switches
limits the “reverse EMF spike” generated when the coil de- is frequency dependent. With increasing frequency, VSWR
energizes to 0.7 volts. The diode cathode is connected to and insertion loss increase while isolation decreases. All
the positive side of the coil and the anode is connected to data sheets specify these three parameters as “worst case”
the negative side.
at the highest operating frequency. If the switch is to be
used over a narrow frequency band, better performance
can be achieved.
Date Code
All switches are marked with either a unique serial number
or a date code. Date codes are in accordance with MIL- Actuator Current vs Temperature
STD-1285 Paragraph 5.2.5 and consist of four digits. The resistance of the actuator coil varies as a function of
The first two digits define the year and the last two digits temperature. There is an inverse relationship between the
define the week of the year (YYWW). Thus, 1032 identifies operating temperature of the switch and the actuator drive
switches that passed through final inspection during the current. For switches operating at 28 VDC, the approximate
32nd week of 2010.
actuator drive current at temperature, T, can be calculated
using the equation:
Failsafe
I
A
A failsafe switch reverts to the default or failsafe position
when actuating voltage is removed. This is realized by a
return spring within the drive mechanism. This type of switch
requires the continuous application of operating voltage to
select and hold any position. (Multi-position switches are
normally open with no voltage applied).
I
=
T
[1 + .00385 (T-20)]
Where:
I
I
=
=
Actuator current at temperature, T
T
Room temperature actuator current –
see data sheet
A
Indicator
Indicators tell the system which position the switch is in.
Other names for indicators are telemetry contacts or tellback
T
=
Temperature of interest in °C
circuit. Indicators are usually a set of internally mounted DC Magnetic Sensitivity
contacts linked to the actuator. They can be wired to digital An electro-mechanical switch can be sensitive to ferrous
input lines, status lights, or interlocks. Unless otherwise materials and external magnetic fields. Neighboring ferrous
specified, the maximum indicator contact rating is 30 Vdc, materials should be permitted no closer than 0.5 inches and
50 mA, or 1.5 Watts into a resistive load.
adjacent external magnetic fields should be limited to a flux
density of less than 5 Gauss.
Isolation
Isolation is the measure of the power level at the output
connector of an unconnected RF channel as referenced to
the power at the input connector. It is specified in dB below
the input power level.
SPECIAL FEATURE
SPDT Switch
Switching High-Power or Highly Sensitive Signals
Ensure the most linear response with the best galvanically
matched contact system in the industry. Extremely low
passive intermodulation is standard on all of our switches.
A single-pole double-throw, bi-directional switch that can
be used as having one input and two outputs or two inputs
and one output.
Switching Time
Carrier
Frequency 1
Carrier
Frequency 2
PIM 3rd Order
Frequency
PIM 5th
Order Fre-
quency
Switching time is the total interval beginning with the arrival
of the leading edge of the command pulse at the switch DC
input and ending with the completion of the switch transfer,
including contact bounce. It consists of three parts: (1)
inductive delay in the coil, (2) transfer time of the physical
movement of the contacts, and (3) the bounce time of the
RF contacts.
870 MHz
SPDT
893 MHz
847 MHz
824 MHz
3rd Order
Intermodulation
5th Order
Intermodulation
–91 dBm
–110 dBm
–134 dBc
–153 dBc
© 2015 TELEDYNE RELAYS
(800) 284-7007 • www.teledynecoax.com
CCS-32/CS-32 Page 7
CCS-32\CS-32\112015\Q4
Series CCS-32/CS-32
High Power DC–12 GHz
Failsafe SPDT Coaxial Switch
COAX SWITCHES
FAILSAFE CCS-32N/CS-32N/ • CCS-32T/CS-32T PART NUMBER LIST
PART NO.
PART NO.
PART NO.
PART NO.
1
CCS-32NXC
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
CS-32NX0-MS
CS-32NX0-S
85
CS-32TX0
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
CS-32HNXC-MS
CS-32HNXC-S
2
CCS-32NXC-D
CCS-32NXC-DM
CCS-32NXC-DMS
CCS-32NXC-DS
CCS-32NXC-M
CCS-32NXC-MS
CCS-32NXC-S
CCS-32NXC-T
CCS-32NXC-TM
CCS-32NXC-TMS
CCS-32NXC-TS
CCS-32NX0
86
CS-32TX0-D
3
CS-32NX0-T
87
CS-32TX0-DM
CS-32TX0-DMS
CS-32TX0-DS
CS-32HNXC-T
4
CS-32NX0-TM
CS-32NX0-TMS
CS-32NX0-TS
CCS-32TXC
88
CS-32HNXC-TM
CS-32HNXC-TMS
CS-32HNXC-TS
CS-32HNX0
5
89
6
90
CS-32TX0-M
7
91
CS-32TX0-MS
8
CCS-32TXC-D
CCS-32TXC-DM
CCS-32TXC-DMS
CCS-32TXC-DS
CCS-32TXC-M
CCS-32TXC-MS
CCS-32TXC-S
CCS-32TXC-T
CCS-32TXC-TM
CCS-32TXC-TMS
CCS-32TXC-TS
CCS-32TX0
92
CS-32TX0-S
CS-32HNX0-D
9
93
CS-32TX0-T
CS-32HNX0-DM
CS-32HNX0-DMS
CS-32HNX0-DS
CS-32HNX0-M
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
94
CS-32TX0-TM
95
CS-32TX0-TMS
CS-32TX0-TS
96
97
CCS-32HNXC
CS-32HNX0-MS
CS-32HNX0-S
CCS-32NX0-D
CCS-32NX0-DM
CCS-32NX0-DMS
CCS-32NX0-DS
CCS-32NX0-M
CCS-32NX0-MS
CCS-32NX0-S
CCS-32NX0-T
CCS-32NX0-TM
CCS-32NX0-TMS
CCS-32NX0-TS
CS-32NXC
98
CCS-32HNXC-D
CCS-32HNXC-DM
CCS-32HNXC-DMS
CCS-32HNXC-DS
CCS-32HNXC-M
CCS-32HNXC-MS
CCS-32HNXC-S
CCS-32HNXC-T
CCS-32HNXC-TM
CCS-32HNXC-TMS
CCS-32HNXC-TS
CCS-32HNX0
99
CS-32HNX0-T
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
CS-32HNX0-TM
CS-32HNX0-TMS
CS-32HNX0-TS
CCS-32HTXC
CCS-32TX0-D
CCS-32TX0-DM
CCS-32TX0-DMS
CCS-32TX0-DS
CCS-32TX0-M
CCS-32TX0-MS
CCS-32TX0-S
CCS-32TX0-T
CCS-32TX0-TM
CCS-32TX0-TMS
CCS-32TX0-TS
CS-32TXC
CCS-32HTXC-D
CCS-32HTXC-DM
CCS-32HTXC-DMS
CCS-32HTXC-DS
CCS-32HTXC-M
CCS-32HTXC-MS
CCS-32HTXC-S
CCS-32HTXC-T
CCS-32HTXC-TM
CCS-32HTXC-TMS
CCS-32HTXC-TS
CCS-32HTX0
CS-32NXC-D
CCS-32HNX0-D
CCS-32HNX0-DM
CCS-32HNX0-DMS
CCS-32HNX0-DS
CCS-32HNX0-M
CCS-32HNX0-MS
CCS-32HNX0-S
CCS-32HNX0-T
CCS-32HNX0-TM
CCS-32HNX0-TMS
CCS-32HNX0-TS
CS-32HNXC
CS-32NXC-DM
CS-32NXC-DMS
CS-32NXC-DS
CS-32NXC-M
CS-32NXC-MS
CS-32NXC-S
CS-32TXC-D
CCS-32HTX0-D
CCS-32HTX0-DM
CCS-32HTX0-DMS
CCS-32HTX0-DS
CCS-32HTX0-M
CCS-32HTX0-MS
CCS-32HTX0-S
CCS-32HTX0-T
CCS-32HTX0-TM
CCS-32HTX0-TMS
CCS-32HTX0-TS
CS-32NXC-T
CS-32TXC-DM
CS-32TXC-DMS
CS-32TXC-DS
CS-32TXC-M
CS-32NXC-TM
CS-32NXC-TMS
CS-32NXC-TS
CS-32NX0
CS-32TXC-MS
CS-32TXC-S
CS-32NX0-D
CS-32HNXC-D
CS-32HNXC-DM
CS-32HNXC-DMS
CS-32HNXC-DS
CS-32HNXC-M
CS-32NX0-DM
CS-32NX0-DMS
CS-32NX0-DS
CS-32NX0-M
CS-32TXC-T
CS-32TXC-TM
CS-32TXC-TMS
CS-32TXC-TS
*
X = 1 (28Vdc), 2 (15Vdc), 3 (12Vdc) and 4 (24Vdc)
CCS-32/CS-32 Page 8
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
© 2015 TELEDYNE COAX SWITCHES
CCS-32\CS-32\112015\Q4
Series CCS-32/CS-32
High Power DC–12 GHz
COAX SWITCHES
Failsafe SPDT Coaxial Switch
FAILSAFE CCS-32N/CS-32N/ • CCS-32T/CS-32T PART NUMBER LIST
PART NO.
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
CS-32HTXC
CS-32HTXC-D
CS-32HTXC-DM
CS-32HTXC-DMS
CS-32HTXC-DS
CS-32HTXC-M
CS-32HTXC-MS
CS-32HTXC-S
CS-32HTXC-T
CS-32HTXC-TM
CS-32HTXC-TMS
CS-32HTXC-TS
CS-32HTX0
CS-32HTX0-D
CS-32HTX0-DM
CS-32HTX0-DMS
CS-32HTX0-DS
CS-32HTX0-M
CS-32HTX0-MS
CS-32HTX0-S
CS-32HTX0-T
CS-32HTX0-TM
CS-32HTX0-TMS
CS-32HTX0-TS
*
X = 6 (28Vdc), 7 (15Vdc), 8 (12Vdc) and 9 (24Vdc)
© 2015 TELEDYNE RELAYS
(800) 284-7007 • www.teledynecoax.com
CCS-32/CS-32 Page 9
CCS-32\CS-32\112015\Q4
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明