1-1393212-1 [TE]
Meets requirements of UL Class F construction;型号: | 1-1393212-1 |
厂家: | TE CONNECTIVITY |
描述: | Meets requirements of UL Class F construction |
文件: | 总4页 (文件大小:1796K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
General Purpose
High Power PCB Relays
Potter & Brumfield
T92 Series Two-pole 30A PCB or Panel Mount Relay
n
n
n
40A, 2 form A (NO) and 2 form C (CO) switching capability
Designed to control compressor loads to 3.5 tons, 110LRA / 25.3FLA
Meets requirements of UL 508 and UL 873 spacings - 8mm through
air, 9.5mm over surface
n
Meets requirements of VDE 8mm spacing, 4kV dielectric coil-to-
contact
n
n
n
Meets requirements of UL Class F construction
UL approved for 600VAC switching (1.5HP)
New screw terminal version (consult factory for availability,
ratings)
Typical applications
HVAC, residential / commercial appliances, industrial controls.
Approvals
Contact ratings 1) (continued)
ARI 780-86 Endurance Test (section 6.6):
HVAC Definite Purpose Contactor Standard
Normally Open Contacts
UL E58304 (Recognized and Listed); CSA LR48471; VDE 40019600
Technical data of approved types on request.
Contact Data
Single Phase/Two Pole (Both poles together switching a single load)
110 LRA, 25.3 FLA, 200K operations (DC Coil)
Contact arrangement
Rated voltage
2 form A (NO), 2 form C (CO)
277VAC
L1
L2
Max. switching voltage
Rated current
Limiting continuous current
Limiting making current
Limiting breaking current
Contact material
Min. recommended contact load
Frequency of operation, with load
Operate/release time max., including bounce
600VAC
30A NO; 3A NC
40A NO; 3A NC
40A NO; 3A NC
40A NO; 3A NC
AgSnOInO, AgCdO
500ma (NO)/ 100ma (NC), 12VAC
360hr
Figure 1
T1
T2
Single Phase Per Pole (Single load per pole)
110 LRA, 18 FLA, 200K operations (DC Coil).
60 LRA, 14 FLA, 200K operations (AC Coil).
L1
L2
25/25ms
Figure 2
T1
T2
Contact ratings 1)
Type
UL508
AgCdO
NO
NO
NO
Load
Cycles
1) Contact ratings at 25°C (unless otherwise noted) with relay properly vented.
FLA, LRA ratings are compatible with 3.5 ton compressor applications.
40A, 277VAC, resistive
30A, 120/277VAC, resistive
10A, 600VAC, general purpose
1HP, 120VAC
6x103
100x103
100x103
100x103
1x103
Mechanical endurance
10x106 ops.
NO
NO
3HP, 240VAC
NO
NO
NO
NO
NO
NO
NC
NC
NC
AgSnOInO
NO
NO
NO
NO
NO
NO
NO
1.5HP, 480 or 600VAC
100x103
100x103
100x103
100x103
100x103
100x103
100x103
100x103
100x103
Coil Data
110LRA/25.3FLA, 240VAC (DC coil only)
60LRA/14FLA, 240VAC (AC coil only)
3A, 240VAC, pilot duty
20A, 28VDC, resistive
TV10, 120VAC
3A, 277VAC
2A, 480VAC
Coil voltage range
5 to 110VDC; 12 to 240VAC
1.7W; 4.0VA
155°C
Max. coil power
Max. coil temperature
Coil insulation system according UL
Coil versions, DC coil
Coil
code
Class F
Rated
voltage
VDC
6
9
12
18
24
48
110
Operate
voltage
VDC
4.5
6.75
9
13.5
18
36
Release
voltage
VDC
0.6
Coil
resistance
Ω 10ꢀ
22
Rated coil
power
W
1A, 600VAC
6
9
12
18
24
48
110
1.7
1.7
1.7
1.7
1.7
1.7
1.7
30A, 120/277VAC, resistive (DC coil only)
30A, 120/277VAC, resistive (AC coil only)
20A, 480VAC, resistive
200x103
100x103
100x103
0.9
48
1.2
1.8
86
197
1.5HP, 120VAC, 2 pole making/breaking (Fig.1) 100x103
2.4
4.8
11
350
1390
7255
3HP, 240VAC, 3 phase (DC coil only)
3HP, 480VAC, 3 phase (DC coil only)
2HP, 600VAC, 3 phase (DC coil only)
100x103
100x103
100x103
82.5
Coil versions, AC coil
VDE
Coil Rated Frequency Operate
Release
voltage resistance power
Coil
Rated coil
AgCdO, flange mount relays
code voltage
VAC
voltage
VAC, 60Hz VAC, 60Hz Ω 10ꢀ
NO
NC
CO
20A, 400VAC
3A, 400VAC
20A NO / 3A NC, 400VAC
100x103
30x103
30x103
Hz
60
60
50/60
50/60
50/60
VA
4
4
4
4
12
24
12
24
9.6
19.2
96
1.2
2.4
12
24
28
9.1
36.6
950
3800
5485
AgCdO, PC mount relays
120 110/120
240 220/240
277 250/277
NO
NC
CO
30A, 400VAC
3A, 400VAC
30A NO / 3A NC, 400VAC
100x103
30x103
30x103
192
222
4
All figures are given for coil without preenergization, at ambient temperature +23°C.
1
11-2012, Rev. 1112
Catalog and product specification according
to IEC 61810-1 and to be used only together
with the ‘Definitions’ section.
Catalog and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Catalog product data, ‘Definitions’ section,
application notes and all specifications are
subject to change.
www.te.com
© 2012 Tyco Electronics Corporation,
a TE Connectivity Ltd. company.
General Purpose
High Power PCB Relays
Potter & Brumfield
T92 Series Two-pole 30A PCB or Panel Mount Relay (Continued)
Coil Data (continued)
Other Data
Ambient temperature vs. coil voltage
Assumptions:
Material compliance: EU RoHS/ELV, China RoHS, REACH, Halogen content
refer to the Product Compliance Support Center at
www.te.com/customersupport/rohssupportcenter
1. Thermal resistance = 35°C per Watt (DC only.)
2. Still air.
3. Nominal coil resistance.
4. Max. mean coil temperature = 155°C (change of resistance method).
5. Coil temperature rise due to load = 6.3°C @ 30 amps.
6. Curves are based on 1.7W at 25°C (DC only.).
Ambient temperature
DC coil
AC coil
Category of environmental protection
IEC 61810
-55ºC to 85ºC
-55ºC to 65ºC
RTI - dust protected,
RTII - flux proof, RTIII - wash tight
1.65mm max excursions, 10-55 Hz
10g for 11msec
120
100
80
60
40
20
0
Vibration resistance (functional)
Shock resistance (functional)
Shock resistance (destructive)
Terminal type
100g
PCB-tht or quick connect
86g
Weight
Resistance to soldering heat THT
IEC 60068-2-20
Packaging/unit
250°C
tray/30 pcs., box/120 pcs.
90 95 100 105 110 115 120 125 130 135 140 145 150
Applied Coil Voltage (% of Rated Nominal)
70 75 80 85
Insulation Data
Initial dielectric strength
between open contacts
between contact and coil
between adjacent contact
Initial surge withstand voltage
between contact and coil
Initial insulation resistance
between insulated elements
Clearance/creepage
1500Vrms
4000Vrms
2000Vrms
6kV
1x109Ω
between contact and coil
8mm clearance/9.5mm creepage
Dimensions
T92 – Mounting and termination code 1
T92 – Mounting and termination code 2, 3 and 4
2.06 MAX.
(52.32)
1.36 MAX.
(34.54)
1.ꢀ6 MAX.
(ꢀ4.54)
2.700 MAX.
(68.58)
1.04 MAX.
(26.42)
1.21 MAX.
(30.73)
1.495 MAX.
(ꢀ7.97)
.156
(3.96)
.250 TYP.
(6.35)
1.618 .020
.047 TYP.
(1.19)
(41.10 .51)
2.05 MAX.
(52.07)
.585 .005
(14.86 .13)
.032 TYP.
(0.81)
.309 .005
(7.85 .13)
2.ꢀ45 .005
(59.56 .1ꢀ)
1.618 TYP.
(41.10 .51)
.585 .005
(14.86 .1ꢀ)
.ꢀ09 .005
(7.85 .1ꢀ)
1.000 .010
(25.40 .25)
.630 .005
(16.00 .13)
.090 RAD.
(2.29)
FOR #8 SCREW
.6ꢀ0 TYP.
(16.00)
2
11-2012, Rev. 1112
www.te.com
© 2012 Tyco Electronics Corporation,
a TE Connectivity Ltd. company.
Catalog and product specification according
to IEC 61810-1 and to be used only together
with the ‘Definitions’ section.
Catalog and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Catalog product data, ‘Definitions’ section,
application notes and all specifications are
subject to change.
General Purpose
High Power PCB Relays
Potter & Brumfield
T92 Series Two-pole 30A PCB or Panel Mount Relay (Continued)
Dimensions
Terminal assignment
Bottom view on pins
T92 – Mounting and termination code 5
2 form A
2 form C
2.700 MAX.
(68.58)
0
1
0
1
1.36 MAX.
(34.54)
.090 (2.29)
RAD. FOR
#8 SCREW
2
6
4
8
2
6
4
8
3
7
2.345 .005
(59.56 .13)
1.431 MAX.
(36.34)
2.135 MAX.
(54.23)
PCB layout
Bottom view on pins
T92 - Mounting and termination code 1
1.618
2.010 MAX.
(51.05)
(41.10)
.585
.913 MAX.
(23.19)
(14.86)
.309
.185
(4.70)
(7.85)
.365
(9.27)
.630
(16.00)
1.000
(25.40)
.203 TYP.
(5.16)
.052 TYP.
(1.32)
.072 TYP.
(1.83)
.162
(4.12)
An alternate PC board layout utilizes .076 .003 (1.93 .076) diameter holes on the same
center-to-center spacing shown above. Use of the rectangular holes is recommended for
improved solderability.
Only necessary terminals are present on single throw models. Consequently, some holes
will be unnecessary for single throw models.
Product code structure
Type
Typical product code
T92
S
11
D
2
2
-24
T92
Printed circuit board / panel mount power relay T92
Enclosure
P
S
Dust protected plastic case
Wash-tight, tape sealed, plastic case (Mounting and termination code 1)
Top sealed, not wash-tight, not tape sealed on bottom (Mounting and termination codes 2, 3 & 4)
Contact arrangement
7
Coil Input
A
2 form A (2 NO)
11 2 form C (2 CO)
AC voltage, 60Hz or 50/60 Hz (consult coil versions table)
D
DC voltage
Mounting and termination
1
2
3
4
5
Printed circuit board mount; printed circuit board terminals.
Panel mount via flanged cover; .250” (6.35mm) x .032” (.81mm) QC terminal
Panel mount via flanged cover; .187” (4.75mm) x .032” (.81mm) QC terminals for coil and .250” (6.35mm) for contacts
Panel mount via flanged cover, .187” (4.75mm) x .020” (.51mm) QC terminals for coil and .250” (6.35mm) for contacts.
Panel mount via flanged cover, M4 screws w/ captive pressure plates. Requires Enclosure P and Contact arrangement 7.
Contact material
2
AgCdO
4
AgSnOInO
Coil voltage
Coil code: please refer to coil versions table
3
11-2012, Rev. 1112
Catalog and product specification according
to IEC 61810-1 and to be used only together
with the ‘Definitions’ section.
Catalog and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Catalog product data, ‘Definitions’ section,
application notes and all specifications are
subject to change.
www.te.com
© 2012 Tyco Electronics Corporation,
a TE Connectivity Ltd. company.
General Purpose
High Power PCB Relays
Potter & Brumfield
T92 Series Two-pole 30A PCB or Panel Mount Relay (Continued)
Product Code
T92P7A22-24
T92P7A22-120
T92P7A22-240
T92P7A22-277
T92P7A24-240
T92P7A52-120
T92P7A52-240
T92P7D12-12
T92P7D12-24
T92P7D22-12
T92P7D22-24
T92P7D22-48
T92P7D24-12
T92P7D24-24
T92P7D42-24
T92P7D52-12
T92P7D52-24
T92P11A12-120
T92P11A22-12
T92P11A22-24
T92P11A22-120
T92P11A22-240
T92P11A22-277
T92P11A24-240
T92P11A42-120
T92P11D12-12
T92P11D22-12
T92P11D22-24
T92P11D24-12
T92P11D24-24
T92S7A12-24
T92S7A12-120
T92S7A12-240
T92S7A22-24
T92S7A22-120
T92S7A22-240
T92S7D12-12
T92S7D12-24
T92S7D12-48
T92S7D12-110
T92S7D14-24
T92S7D22-12
T92S7D22-18
T92S7D22-24
T92S7D22-110
T92S11A12-24
T92S11A12-120
T92S11A12-240
T92S11A22-12
T92S11A22-24
T92S11A22-120
T92S11A22-240
T92S11D12-12
T92S11D12-24
T92S11D12-48
T92S11D12-110
T92S11D22-12
T92S11D22-24
Enclosure
Contacts
Coil
Mounting
Contact Material
Coil
Part Number
6-1393211-0
5-1393211-7
6-1393211-2
6-1393211-3
3-1423008-3
1423008-8
1-1423008-2
6-1393211-5
6-1393211-6
6-1393211-9
7-1393211-1
7-1393211-2
2-1423008-2
1423008-9
Plastic dust cover 2 form A, 2 NO
AC
Panel mount + quick connect
AgCdO
24 VAC
120 VAC
240 VAC
277 VAC
240 VAC
120 VAC
240 VAC
12 VDC
24 VDC
12VDC
AgSnOInO
AgCdO
Panel mount + screw terminals
PCB terminals
DC
Panel mount + quick connect
24 VDC
48 VDC
12VDC
AgSnOInO
AgCdO
24 VDC
7-1393211-5
1-1423008-0
1423967-1
Panel mount + screw terminals
12 VDC
24 VDC
120 VAC
12 VAC
2 form C, 2 CO
AC
PCB terminals
Panel mount + quick connect
3-1393211-8
3-1393211-9
4-1393211-3
4-1393211-0
4-1393211-4
4-1393211-6
3-1423008-7
4-1393211-8
5-1393211-0
5-1393211-3
5-1393211-4
3-1423008-5
3-1423008-6
9-1393211-8
9-1393211-7
9-1393211-9
1393212-4
24 VAC
120 VAC
240 VAC
277 VAC
240 VAC
120VAC
12 VDC
AgSnOInO
AgCdO
DC
AC
PCB terminals
Panel mount + quick connect
24 VDC
12 VDC
24 VDC
24 VAC
120 VAC
240 VAC
24 VAC
120 VAC
240 VAC
12 VDC
24 VDC
48 VDC
110 VDC
24 VDC
12 VDC
18 VDC
24 VDC
110 VDC
24 VAC
120 VAC
240 VAC
12 VAC
24 VAC
120 VAC
240 VAC
12 VDC
24 VDC
48 VDC
110 VDC
12 VDC
24 VDC
AgSnOInO
AgCdO
Wash tight
Top sealed
Wash tight
2 form A, 2 NO
PCB terminals
Panel mount + quick connect
PCB terminals
1393212-2
1393212-5
1393212-8
1-1393212-0
1-1393212-1
1393212-7
DC
AgSnOInO
AgCdO
1-1423008-8
1-1393212-4
1-1393212-5
1-1393212-7
1-1393212-3
8-1393211-1
8-1393211-0
8-1393211-2
8-1393211-3
8-1393211-6
8-1393211-4
8-1393211-7
8-1393211-9
9-1393211-0
9-1393211-1
8-1393211-8
9-1393211-3
9-1393211-4
Top sealed
Panel mount + quick connect
Wash tight
Top sealed
2 form C, 2 CO
AC
DC
PCB terminals
Panel mount + quick connect
Wash tight
Top sealed
PCB terminals
Panel mount + quick connect
4
11-2012, Rev. 1112
www.te.com
© 2012 Tyco Electronics Corporation,
a TE Connectivity Ltd. company.
Catalog and product specification according
to IEC 61810-1 and to be used only together
with the ‘Definitions’ section.
Catalog and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Catalog product data, ‘Definitions’ section,
application notes and all specifications are
subject to change.
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明