1422002-8 [TE]
Standard telecom relay;
| 型号： | 1422002-8 |
| 厂家： | 
TE CONNECTIVITY |
| 描述： | Standard telecom relay 光电二极管 继电器 |
| 文件： | 总7页 (文件大小：1946K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Signal Relays
AXICOM
P2 Relay V23079
n
n
n
n
n
n
n
Standard telecom relay (ringing and test access)
Slim line 15x7.5mm (.590x.295”)
Max. switching current 5A
2 form C bifurcated contacts (2 changeover contacts, 2 CO)
Immersion cleanable
High sensitivity for low power consumption 140mW/ 70mW
Single coil version with surge voltage resistance between contact
and coil: 2.5kV (2/10μs) meets the Telcordia Requirement GR-1089,
1.5kV (10/160μs) meets FCC Part 68
Typical applications
Communications equipment linecard application (ringing and test access),
PABX, voice over IP, office equipment, measurement and control equipment,
automotive equipment as CAN bus, keyless entry, speaker switch, medical
equipment, consumer electronics, set top boxes, HiFi
Z
Approvals
UL 508 File No. E 111441, UL 60950,
IEC/EN60950 IEC Ref. Cert. No. 327
Technical data of approved types on request
Coil Data
Magnetic system
Coil voltage range
Max. coil temperature
Thermal resistance
polarized
2 to 24VDC
125°C
< 125K/W
Contact Data
Contact arrangement
Max. switching voltage
Rated current
2 form C (CO)
220VDC, 250VAC
2A
Coil versions, monostable
Coil
code
Rated
voltage
VDC
3.00
4.00
4.50
5.00
6.00
9.00
Operate Limiting Release
Coil
Rated coil
voltage
VDC
2.25
3.00
3.38
3.75
4.50
6.75
9.00
18.00
Voltage
VDC
6.50
8.70
9.80
10.90
13.00
19.60
26.15
52.30
voltage resistance power
Limiting continuous current, 85°C
Switching Power
Contact material
2A
VDC
0.30
0.40
0.45
0.50
0.60
0.90
1.20
2.40
Ω 10ꢀ
64
114
145
178
257
578
1029
4114
mW
140
140
140
140
140
140
140
140
60W, 62.5VA
AgNi, gold-covered
bifurcated contact
100μV
008
016
011
001
002
006
003
005
Contact style
Minimum switching voltage
Thermoelectrical potential
Initial contact resistance
Frequency of operation, without load
Operate time
Set/reset time
Release time
<10µV
<50mΩ at 10mA, 20mV
50 operations/s
typ. 2ms, max. 4ms
typ. 2ms, max. 4ms
12.00
24.00
All figures are given for coil without pre-energization, at ambient temperature +23°C.
Other coil voltages on request.
without diode in parallel
with diode in parallel
Bounce time
Electrical endurance
at 12V / 10mA
at 6V / 100mA
at 60V / 500mA
at 30V / 1000mA
at 30V / 2000mA
Contact ratings, UL
typ. 2ms, max. 4ms
typ. 4ms, max. 6ms
typ. 1ms, max. 3ms
2.8
140 mW
2.6
Umax. at 0 A
Umax. at 2 x 1 A
Umax. at 2 x 2 A
2.4
typ. 5x107 operations
typ. 1x107 operations
typ. 5x105 operations
typ. 1x106 operations
typ. 2x105 operations
110VDC / 0.3A - 33W
30VDC / 2.0A - 60W
120VAC / 0.5A - 60VA
240VAC / 0.25A -60VA
typ. 100x106 operations
2.2
2
1.8
1.6
1.4
1.2
Unom. nominal coil voltage
1
0.8
0.6
Uop. min.
Urel. min.
0.4
Mechanical endurance
0.2
0
Max. DC load breaking capacity
-40 -30 -20 -10
0
10 20 30 40 50 60 70 80 90 100 110 120 130 140
Ambient Temperature [°C]
DC current [A]
1
07-2015, Rev.0715
Datasheets and product specification
according to IEC 61810-1 and to be used
only together with the ‘Definitions’ section.
Datasheets and product data is subject to the
Datasheets, product data, ‘Definitions’ sec-
tion, application notes and all specifications
are subject to change.
www.te.com
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
© 2015 Tyco Electronics Corporation,
a TE Connectivity Ltd. company
Signal Relays
AXICOM
P2 Relay V23079 (Continued)
Coil Data (continued)
Insulation Data
Initial dielectric strength
Standard
HDV
between open contacts
between contact and coil
between adjacent contacts
Initial surge withstand voltage
1000Vrms
1500Vrms
1000 Vrms
1500Vrms
1500Vrms
1500Vrms
Limiting
Voltage
VDC
Reset
Coil
Rated coil
voltage resistance power
VDC
Ω 10ꢀ
mW
Bistable, 1 coil
according to Telcordia TR-NWT-001089 (2/10μs)
108
111
101
102
106
103
105
3.00
4.50
5.00
6.00
9.00
12.00
24.00
2.25
3.38
3.75
4.50
6.75
9.00
18.00
9.2
13.85
15.33
18.5
27.75
37
-2.25
-3.38
-3.75
-4.50
-6.75
-9.00
-18.00
128
289
357
70
70
70
70
70
70
70
between open contacts
between contact and coil
between adjacent contacts
according to (10/700 μs IEC 60950)
between open contacts
between contact and coil
between adjacent contacts
Initial insulation resistance at 500 Vdc
Capacitance
2000V
2500V
2500V
2500V
2500V
2500V
514
1157
2057
8228
2000V
2500V
2500V
2500V
2500V
2500V
74
Bistable, 2 coil
> 109Ω
219
218
208
211
201
202
206
203
205
2.00
2.40
3.00
4.50
5.00
6.00
9.00
12.00
24.00
1.50
1.80
2.25
3.38
3.75
4.50
6.75
9.00
18.00
4.33
5.2
6.5
9.8
10.9
13
19.6
26.15
52.3
1.50
1.80
2.25
3.38
3.75
4.50
6.75
9.00
18.00
28
41
64
145
178
257
578
1029
4114
140
140
140
140
140
140
140
140
140
between open contacts
max. 1pF
max. 2pF
max. 1.5pF
between contact and coil
between adjacent contacts
Clearance /creepage
according to IEC / EN 60950
1.3/2.5mm
Other Data
All figures are given for coil without pre-energization, at ambient temperature +23°C.
Other coil voltages on request.
Material compliance: EU RoHS/ELV, China RoHS, REACH, Halogen content
refer to the Product Compliance Support Center at
3.4
www.te.com/customersupport/rohssupportcenter
70 mW
3.2
Ambient temperature
-40 to +85°C
3
Umax. at 0 A
Umax. at 2 x 1 A
Umax. at 2 x 2 A
Category of environmental protection
IEC 61810
Vibration resistance (functional)
Shock resistance (functional)
IEC 60068-2-27 (half sine)
Terminal type
2.8
RT III - wash tight
35g, 10 to 1000Hz
2.6
2.4
2.2
2
100g
PCB-THT,
1.8
1.6
1.4
1.2
SMT long and short terminals
max. 2.8 g
Weight
Unom. nominal coil voltage
1
Resistance to soldering heat THT
IEC 60068-2-20
0.8
265°C/10s
Uop. min.
0.6
Moisture sensitive level, JEDEC J-Std-020D
related only to SMT relays
packed in orginal dry-packs
Ultrasonic cleaning
Packaging/unit
THT
MSL3
0.4
0.2
0
-40 -30 -20 -10
0
10 20 30 40 50 60 70 80 90 100 110 120 130 140
not recommended
box/2000 pcs.
Ambient Temperature [°C]
Coil versions, high dielectric version, monostable, overmolded
Coil
code
Rated
voltage
VDC
3.00
5.00
6.00
9.00
12.00
Coil
Rated coil
SMT
reel/2000 pcs. or 2500 pcs.
Ω 10ꢀ
45
125
180
405
mW
200
200
200
200
200
008
001
002
006
003
720
All figures are given for coil without pre-energization, at ambient temperature +23°C.
Other coil voltages on request.
200 mW
2.8
2.6
Umax. at 0 A
Umax. at 2 x 1 A
2.4
Umax. at 2 x 2 A
2.2
2
1.8
1.6
1.4
1.2
Unom. nominal coil voltage
1
0.8
0.6
Uop. min.
Urel. min.
0.4
0.2
0
-40 -30 -20
0
10 20
50 60 70 80 90
110 120 130 140
-1A0 mbient 3T0e4m0 perature [°C1]00
2
07-2015, Rev. 0715
Datasheets and product specification
according to IEC 61810-1 and to be used
only together with the ‘Definitions’ section.
Datasheets and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Datasheets, product data, ‘Definitions’ sec-
tion, application notes and all specifications
are subject to change.
www.te.com
© 2015 Tyco Electronics Corporation,
a TE Connectivity Ltd. company
Signal Relays
AXICOM
P2 Relay V23079 (Continued)
Terminal assignment
TOP view on component side of PCB
Monostable version
Bistable version, 1-coil
Bistable version, 2-coils
Contacts are shown in reset
condition.
Both coils can be used as
either set or reset coils.
Contact position might change
during transportation and must
be reset before use.
PCB layout
TOP view on component side of PCB
THT version
SMT, long terminals
SMT, short terminals
0,9 0,ꢀ
Dimensions
Standard coil
THT version
SMT, long terminals
SMT, short terminals
14.5 0.1
7.2 0.1
14.5 0.1
7.2 0.1
14.5 0.1
7.2 0.1
0.5 0.05
5.52 0.15
9.4 0.15
5.52
0.5 0.05
0.5 0.05
7.4 0.15
Overmolded coil, high dielectric version
THT version
SMT, long terminals
SMT, short terminals
ꢀ4.6 0.ꢀ
7.2 0.ꢀ
ꢀ4.6 0.ꢀ
7.2 0.ꢀ
ꢀ4.6 0.ꢀ
7.2 0.ꢀ
5.52
0.5 0.05
0.5 0.05
5.52
0.5 0.05
9.4 0.ꢀ5
7.4 0.ꢀ5
3
07-2015, Rev.0715
Datasheets and product specification
according to IEC 61810-1 and to be used
only together with the ‘Definitions’ section.
Datasheets and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Datasheets, product data, ‘Definitions’ sec-
tion, application notes and all specifications
are subject to change.
www.te.com
© 2015 Tyco Electronics Corporation,
a TE Connectivity Ltd. company
Signal Relays
AXICOM
P2 Relay V23079 (Continued)
Processing
Recommended soldering conditions
Vapour phase soldering
20 to 40s
full line: typical
dotted line: process limits
240°C
180°C
forced cooling
130°C
external preheating
100°C
Vapour phase soldering
temperature/time profile
(lead and housing peak temp.)
Time [s]
Recommended reflow soldering profile
Infrared soldering
temperature/time profile
(lead and housing peak temp.)
Time [s]
Packing
Reel dimensions
4
07-2015, Rev. 0715
Datasheets and product specification
according to IEC 61810-1 and to be used
only together with the ‘Definitions’ section.
Datasheets and product data is subject to the
Datasheets, product data, ‘Definitions’ sec-
tion, application notes and all specifications
are subject to change.
www.te.com
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
© 2015 Tyco Electronics Corporation,
a TE Connectivity Ltd. company
Signal Relays
AXICOM
P2 Relay V23079 (Continued)
NEW
roztec transportnich otvoru 1.5
distance of transport holes 1.5
4x10=40±0.2mm
4x11=44±0.2mm
4x12=48±0.2mm
B
(8)
(48)
1.5 0.1
(
1.5)
4±0.1
2±0.1
NEW
B-B
A-A
4±0.2
A
10±0.2
12±0.2
12.2±0.2
1.2+00.2
B
1.5 0.1
16±0.15
16
1.5 0.1
B
m
m
NEW
4±0.1
2±0.1
A-A
B-B
A
4±0.2
A
8±0.2
9±0.2
1.2+00.2
9.1±0.2
1.5 0.1
B
12±0.15
Tape and reel for SMT
9
12
5
07-2015, Rev.0715
www.te.com
© 2015 Tyco Electronics Corporation,
a TE Connectivity Ltd. company
Datasheets and product specification
according to IEC 61810-1 and to be used
only together with the ‘Definitions’ section.
Datasheets and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Datasheets, product data, ‘Definitions’ sec-
tion, application notes and all specifications
are subject to change.
Signal Relays
AXICOM
P2 Relay V23079 (Continued)
Product code structure
Type
Typical product code V23079
A
1
001
B
301
V23079 Signal Relay P2 Series
Version
A
THT, monostable
THT, latching, 2 coils
THT, latching, 1 coil
D
E
F
SMT, monostable, long term.
SMT, latching, 2 coils long term.
SMT, latching, 1 coil long term.
G
H
J
SMT, monostable, short term.
SMT, latching, 2 coils short term.
SMT, latching, 1 coil short term.
B
C
Coil design
1
2
Standard coil (not for high dielectric version)
Overmolded coil
Coil
Coil code: please refer to coil versions table
Version
B
X
Standard version
High dielectric version
Contacts for standard versions
301
201
2 form C contacts (2 CO), AgNi +Au
2 form C contacts (2 CO), AgPd +Au; on request only
Product code
Version
Coil design
Coil type
Coil voltage
9VDC
Part number
2-1393788-0
1-1393788-6
6-1419120-6
3-1393789-9
3-1393789-5
3-1393789-6
3-1393789-8
3-1393789-7
1422002-8
4-1393788-1
4-1393788-2
3-1393788-3
3-1393788-5
3-1393788-9
3-1393788-6
3-1393788-7
1-1422002-2
1-1422002-1
1-1422002-0
1422002-9
V23079-A1006-B301
V23079-A1005-B301
V23079-A2008-B301
V23079-A2011-B301
V23079-A2001-B301
V23079-A2002-B301
V23079-A2006-B301
V23079-A2003-B301
V23079-B1218-B301
V23079-B1208-B301
V23079-B1211-B301
V23079-B1201-B301
V23079-B1202-B301
V23079-B1206-B301
V23079-B1203-B301
V23079-B1205-B301
V23079-B2219-B301
V23079-B2218-B301
V23079-B2208-B301
V23079-B2201-B301
V23079-C1108-B301
V23079-C1111-B301
V23079-C1101-B301
V23079-C1102-B301
V23079-C1106-B301
V23079-C1103-B301
V23079-C1105-B301
24VDC
3VDC
4.5VDC
5VDC
6VDC
9VDC
12VDC
2.4VDC
3VDC
4.5VDC
5VDC
6VDC
9VDC
12VDC
24VDC
2VDC
2.4VDC
3VDC
5VDC
3VDC
4.5VDC
5VDC
6VDC
9VDC
12VDC
24VDC
Overmolded
Standard
Bistable, 2 coils
Overmolded
Standard
Bistable, 1 coils
5-1393788-3
5-1393788-4
4-1393788-5
4-1393788-7
5-1393788-1
4-1393788-8
5-1393788-0
6
07-2015, Rev. 0715
Datasheets and product specification
according to IEC 61810-1 and to be used
only together with the ‘Definitions’ section.
Datasheets and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Datasheets, product data, ‘Definitions’ sec-
tion, application notes and all specifications
are subject to change.
www.te.com
© 2015 Tyco Electronics Corporation,
a TE Connectivity Ltd. company
Signal Relays
AXICOM
P2 Relay V23079 (Continued)
Product code
Version
Coil design
Coil type
Coil voltage
9VDC
Part number
V23079-D1006-B301
V23079-D1005-B301
V23079-D2008-B301
V23079-D2011-B301
V23079-D2001-B301
V23079-D2002-B301
V23079-D2006-B301
V23079-D2003-B301
V23079-E1219-B301
V23079-E1218-B301
V23079-E1208-B301
V23079-E1211-B301
V23079-E1201-B301
V23079-E1202-B301
V23079-E1206-B301
V23079-E1203-B301
V23079-E1205-B301
V23079-E2219-B301
V23079-E2201-B301
V23079-E2208-B301
V23079-E2218-B301
V23079-F1108-B301
V23079-F1111-B301
V23079-F1101-B301
V23079-F1102-B301
V23079-F1106-B301
V23079-F1103-B301
V23079-F1105-B301
V23079-G1005-B301
V23079-G2008-B301
V23079-G2016-B301
V23079-G2011-B301
V23079-G2001-B301
V23079-G2002-B301
V23079-G2006-B301
V23079-G2003-B301
V23079-H1208-B301
V23079-H1211-B301
V23079-H1201-B301
V23079-H1202-B301
V23079-H1206-B301
V23079-H1203-B301
V23079-H1205-B301
V23079-J1108-B301
V23079-J1111-B301
V23079-J1101-B301
V23079-J1102-B301
V23079-J1103-B301
V23079-J1105-B301
V23079-G2008-X079
V23079-G2001-X071
V23079-G2002-X072
V23079-G2006-X073
V23079-G2003-X074
V23079-A2003-X074
V23079-A2008-X079
5-1393788-9
5-1393788-8
4-1393789-7
4-1393789-8
4-1393789-3
4-1393789-4
4-1393789-6
4-1393789-5
1-1422007-0
1422007-5
24VDC
3VDC
4.5VDC
5VDC
6VDC
9VDC
12VDC
2VDC
2.4VDC
3VDC
4.5VDC
5VDC
6VDC
Overmolded
Standard
Bistable, 2 coils
7-1393788-1
7-1393788-2
6-1393788-8
1393789-5
9VDC
1393789-9
12VDC
24VDC
2VDC
5VDC
3VDC
2.4VDC
3VDC
4.5VDC
5VDC
6VDC
6-1393788-9
7-1393788-0
1422007-6
1422007-7
1422007-8
Overmolded
Standard
1422007-9
7-1393788-5
1-1393789-4
7-1393788-3
1-1393789-0
1-1393789-2
7-1393788-4
1-1393789-1
7-1393788-8
5-1393789-4
1393790-5
5-1393789-5
4-1393789-9
5-1393789-0
5-1393789-3
5-1393789-1
2-1393789-4
8-1393788-4
2-1393789-0
2-1393789-1
2-1393789-3
8-1393788-3
2-1393789-2
2-1393789-9
3-1393789-0
2-1393789-5
2-1393789-6
2-1393789-7
2-1393789-8
1422006-5
Bistable, 1 coil
Monostable
9VDC
12VDC
24VDC
24VDC
3VDC
4VDC
4.5VDC
5VDC
6VDC
9VDC
12VDC
3VDC
4.5VDC
5VDC
6VDC
9VDC
12VDC
24VDC
3VDC
4.5VDC
5VDC
SMT, short pins
Overmolded
Standard
Bistable, 2 coils
Bistable, 1 coil
Monostable
6VDC
12VDC
24VDC
3VDC
5VDC
6VDC
High dielectric
Overmolded
1422006-1
1422006-2
1422006-3
1422006-4
1422025-7
1-1422025-1
9VDC
12VDC
12VDC
3VDC
7
07-2015, Rev.0715
Datasheets and product specification
according to IEC 61810-1 and to be used
only together with the ‘Definitions’ section.
Datasheets and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Datasheets, product data, ‘Definitions’ sec-
tion, application notes and all specifications
are subject to change.
www.te.com
© 2015 Tyco Electronics Corporation,
a TE Connectivity Ltd. company
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明