2018002-6 [TE]

Read these instructions thoroughly before using the seating tool kit.;


型号：	2018002-6
厂家：	TE CONNECTIVITY
描述：	Read these instructions thoroughly before using the seating tool kit.
文件：	总4页 (文件大小：349K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

Instruction Sheet

Small Form-Factor Pluggable (SFP)+ and (SFT+

Enhanced) Surface Mount PT Connector and Cage

Assembly Seating Tool Kits 2018002-[ ] and 2215005-[

408-10155

20 JAN 15 Rev C

1 X 4 Seating Tool

(Bottomed on Cage Assembly)

Back of

Seating Tool

Seating Tool Kit 2018002-1 (Shown)

1 X 4 Cage Assembly

2007576 (Shown)

1 X 4 Wall Support

(For Clarity, Not

Shown Installed

Compliant

Pin Contact

Printed Circuit

(PC) Board (Ref)

SFT+ CAGE

SFP+ ENHANCED

CAGE ASSEMBLY

CONFIGURATION

SEATING

TOOL KIT

APPLICATION

PC Board Support

Fixture (Ref)

ASSEMBLY

SPECIFICATION

CONFIGURATION

2018002-1

2018002-2

2018002-3

2018002-4

2018002-5

2018002-6

2215005-1

2215005-2

2215005-3

1 X 4

1 X 6

1 X 2

1 X 3

1 X 1

1 X 5

---

NOTE: Connector not shown.

---

114-13120

---

1 X 4

1 X 6

1 X 2

---

Figure 1

1. INTRODUCTION

SFP+ surface mount PT connector and cage assembly seating tool kits listed in Figure 1 are used to seat the

cage assemblies described in Figure 1 onto the pc board. The cage assembly contains compliant pin contacts

to allow solderless pc board installation. The seating tool is not designed to seat the connector.

Read these instructions thoroughly before using the seating tool kit.

NOTE

Dimensions on this sheet are in metric units [with U.S. customary units in brackets]. Figures and illustrations are for reference

only and are not drawn to scale.

2. DESCRIPTION (Figure 1)

Each seating tool kit consists of a seating tool and a wall support. The seating tool and wall support are also

available separately. The seating tool has cutouts (two located on each side) to accept the protruding part of

the standoffs of the cage assembly. The wall support must be installed into the ports of the cage assembly.

The top of the seating tool provides a surface to accept the force applied by the application tool to seat the

product onto the pc board. During seating, the back and sides of the seating tool protect the cage assembly

from damage. The wall support supports the individual ports of the cage assembly.

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.te.com.

*Trademark

TOOLING ASSISTANCE CENTER 1-800-722-1111

PRODUCT INFORMATION 1-800-522-6752

1 of 4

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners.

408-10155

3. REQUIREMENTS

3.1. PC Board Support Fixture (Customer Supplied)

A pc board support must be used to provide proper support for the pc board and to protect the pc board and

the connector and cage assembly from damage. The support fixture must be designed for specific needs using

the following recommendations:

 it should be at least 25.4 mm [1 in.] longer and wider than the pc board

 it should have flat surfaces with holes or a channel large enough and deep enough to receive any

protruding components of the product

3.2. Application Tool

Power for seating tools must be provided by an application tool (with a ram) capable of supplying a downward

force of 44.5 N [10 lb-force] per contact. For available application tools, call PRODUCT INFORMATION at the

number at the bottom of page 1.

CAUTION

Over-driving of the cage assembly will deform parts critical to the quality of the connection. Maximum force occurs prior to the

cage assembly bottoming on the pc board.

4. SETUP

When setting up equipment to seat the cage assembly, pay particular attention to the following:

 the seating tool must be matched to the cage assembly

CAUTION

If the seating tool and cage assembly are mismatched or are improperly aligned, damage could occur to the tooling, cage

assembly, or both.

 light pipes MUST NOT be assembled onto the cage assembly

 the wall support must be properly installed, and the seating tool, cage assembly, and application tool ram

must be properly aligned before cycling the application tool

1. Set the tool seating height to the dimension shown in Figure 2 (application tool shut height will equal

the tool seating height PLUS the combined thicknesses of the pc board and support fixture).

After seating, a gap of no more than 0.10 mm [.004 in.] between the cage assembly standoffs and the

pc board is allowed.

NOTE

Use the tool seating height as a reference starting point. This height may need to be adjusted to obtain the amount allowed

(maximum of 0.10 mm [.004 in.]) between the standoffs of the cage assembly and the pc board.

2. Slide the wall support into the ports of the cage assembly until the wall support is secure.

5. SEATING (Figure 2)

NOTE

The connector must be mounted on the pc board BEFORE seating the cage assembly.

1. Place the pc board on the support fixture.

2. Orient the seating tool over the cage assembly so that the back is aligned with the back of the cage

assembly. Then lower the seating tool onto the cage assembly, making sure that the cutouts slide

over the protruding components of the cage assembly, until the seating tool bottoms on the top of the

cage assembly.

3. Place the cage assembly on the pc board so that the contacts and alignment posts are aligned and

started into the matching holes in the pc board.

4. Center the seating tool (with the cage assembly) under the ram of the application tool. Slowly lower

the ram until it just meets the seating tool. Verify alignment of pc board support, pc board, cage

assembly, and seating tool.

2 of 4

Rev C

408-10155

Ram of Application

Tool (Fully Down

Seating Tool

Tool Seating Height

38.61 [1.52] (With Cage

Assembly Seated)

Wall Support (Installed in

Ports of Cage Assembly

Compliant Pin Contacts (and

Any Protruding Components)

inserted into Holes in PC Board

and PC Board Support Fixture

Application Tool Shut

Height

(Ram Fully Down)

(See Section 4, Step 1)

0.10 [.004] (Max)

Gap Allowed

PC Board

PC Board Support

Fixture (Ref)

Figure 2

CAUTION

Damage to the pc board, seating tool, or cage assembly may occur if the seating tool is not properly seated on the cage

assembly before cycling the application tool.

5. Cycle the application tool to seat the cage assembly on the pc board. Then retract the ram, and

carefully remove the seating tool by pulling it straight from the cage assembly.

6. Check the cage assembly for proper seating according to the following:

a. the widest section of each compliant pin is inside its intended pc board hole

b. each alignment post is in its intended pc board hole

c. if present, the gap between the standoffs and the pc board is no more than 0.10 mm [.004 in.]

NOTE

For detailed application requirements of the cage assembly, refer to the application specification given in Figure 1.

6. MAINTENANCE AND INSPECTION

The seating tool kit is assembled and inspected before shipment. It is recommended that the seating tool kit be

inspected immediately upon arrival at your facility to ensure that it has not been damaged during shipment, and

that it conforms to the dimensions provided in Figure 3.

6.1. Daily Maintenance

It is recommended that each operator be made aware of, and responsible for, the following steps of daily

maintenance:

1. Remove dust, moisture, and contaminants with a clean, soft brush or a lint-free cloth. DO NOT use

objects that could damage the components.

2. When the seating tool and wall support are not in use, store them in a clean, dry area.

6.2. Periodic Inspection

Regular inspections should be performed by quality control personnel. A record of scheduled inspections

should remain with the seating tool or be supplied to personnel responsible for the seating tool kit. Inspection

frequency should be based on amount of use, working conditions, operator training and skill, and established

standards.

3 of 4

Rev C

408-10155

7. REPLACEMENT AND REPAIR

Customer-replaceable parts are listed in Figure 3. A complete inventory should be stocked and controlled to

prevent lost time when replacement of parts is necessary. Parts other than those listed should be replaced by

TE Connectivity to ensure quality and reliability. Order replacement parts through your TE Representative, or

call 1-800-526-5142, or send a facsimile of your purchase order to 717-986-7605, or write to:

CUSTOMER SERVICE (038-035)

TYCO ELECTRONICS CORPORATION

PO BOX 3608

HARRISBURG PA 17105-3608

8. REVISION SUMMARY

 Added part number 2018002-6 and related information to tables in Figures 1 and 3

Seating Tool Kit 2018002-1 (1 X 4, Shown)

Front

Side

Top

Front

End

D (2 Places)

SEATING TOOL KIT

DIMENSION

(By Cage Assembly

Configuration)

1 X 1

1 X 2

1 X 3

1 X 4

1 X 5

1 X 6

17.78 [.700]

44.70 [1.760] 33.02 [1.300]

4.57 [.180]

4.50 [.177]

4.57 [.180]

13.64 [.537]

27.94 [1.100]

42.16 [1.660]

56.39 [2.220]

70.66 [2.782]

84.33 [3.320]

8.38 [.330]

50.8 [2.00]

31.75 [1.250] 44.70 [1.760] 33.02 [1.300]

46.07 [1.814] 44.70 [1.760] 33.02 [1.300]

60.33 [2.375] 44.70 [1.760] 33.02 [1.300]

75.20 [2.960] 43.20 [1.700] 34.00 [1.338]

88.90 [3.500] 44.70 [1.760] 33.02 [1.300]

REPLACEMENT PARTS

PART NUMBER FOR KIT (By Cage Assembly Configuration)

QTY PER

KIT

ITEM DESCRIPTION

1 X 1

1 X 2

1 X 3

1 X 4

1 X 5

1 X 6

Seating Tool

Wall Support

2018003-5

1725606-5

2018003-3

1725606-3

2018003-4

1725606-4

2018003-1

1725606-1

2215633-1

1725606-6

2018003-2

1725606-2

PART NUMBER FOR SFP+ ENHANCED KIT (By Cage Assembly Configuration)

QTY PER

KIT

ITEM DESCRIPTION

1 X 2

1 X 4

1 X 6

Seating Tool

Wall Support

2215267-3

1725606-3

2215267-1

1725606-1

2215267-2

1725606-2

Figure 3

4 of 4

Rev C

2018002-6 [TE]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB

SI9137LG

SI9122E